Used Electric Drill Machine for sale (85,716)

Condition: good (used), Year of construction: 1985, spindle turning speed - stepless 26 - 1650 U/min voltage 380 V Rcedpovylh Usfx Ahgsf 0 50 Hz rated current 15 A connected load 6,5 kW tool taper MK 4 weight of the machine ca. 2,3 t dimensions of the machine ca. 1500 x 1200 x 2500 mm Operating voltage: 380 V Frequency: 50 Hz Control voltage: 220 V Rated current: 15 A Connection: 6.5 kW Automatic feed: 0.05 - 0.45 mm/rev Column lifting speed: 40 mm/s Column stroke: 450 mm Drilling spindle stroke: 200 mm Drilling zone: 430 - 1150 mm Height adjustment of the drilling spindle: 330 - 780 mm Tool holder: MK 4 Table dimensions: 1525 x 560 mm Table height: 800 mm

Condition: used, Small Drilling/Milling Machine ISERT ELECTRONIC Travel X: 350 mm Travel Y: 300 mm Travel Z: 70 mm Rotation: 8000 / 9500 / 13500 / 20500 / 24000 RPM The machine could be used for drilling printed circuit boards or other use. The machine was controlled through a PC that is no longer present. Possibility to use it in manual Rcsdpfx Aezw Azcjhgof Equipped with: 1 Milling Machine KRESS Voltage: 220 V mono Dimensions (L x W x H): 950 x 700 x 700 mm Weight: approx 60 KG

Condition: used, Drilling / Milling machine OPTIMUM type OPTI F 40 E Travel X: 500 mm Travel Y: 200 mm Spindle: Ø 80 mm Cone CM3 Spindle exit: 120 mm Spindle speed: from 95 to 3200 RPM Table size: Length 730 mm x Width 210 mm 2 speeds motor Motor power: 1,5 Kw Rcodpfx Ahezw Ay Ssgjf Straight head Cross table Manual Descent Equipped with: 1 rotary vice Voltage: 380 V Dimensions (L x W x H): 1200 x 900 x 1400 mm Weight: approx 350 KG

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, Drilling / Milling Machine KNUTH MARK SUPER SV Year of construction: 2021 Travel X: 560 mm Travel Y: 190 mm Travel Z: 400 mm Spindle: CM4 Spindle exit: 120 mm Spindle speed: from 75 to 2500 RPM Table size: 800 x 240 mm Tilting head Scale 3 axes Rodpjzw Ayxofx Ahgscf Electronic speed variator Automatic head up/down Automatic X axe travel Manual Y axe travel Supplied with many accessories: Boring heads, clamps holders, etc (see photos) Voltage: 380 V Length: 1400 mm Depth: 1200 mm Height: 2000 mm Weight: approx 500 KG

Condition: used, Radial Drilling Machine SCHLUMBERGER 36-12 Spindle: Ø 110 mm - Right rotation Cone: CM4 Spindle exit: 200 mm Rotation: from 40 to 750 RPM Table size: 1000 x 700 mm Rsdpfxezw Ayle Ahgecf Slide travel: 700 mm Automatic descent Recent electrical panel Lubricant pump Voltage: 380 V Back table dimensions: 1200 x 750 mm Machine support dimensions: 1400 x 1200 mm Total height in height position: 2800 mm Total height in low position: 2550 mm Weight: approx 3,5 T

Condition: used, Radial Drilling Machine BERGONZI type UT 25 Spindle: CM3 Spindle exit: 150 mm Spindle speed: from 130 to 900 RPM Arm travel: 500 mm Max height table/spindle nose: 900 mm Column: Ø 180 mm 2 speeds motor Auto descent Return Spring defective Electric arm rise Delivered with: 1 cube Length 500 mm x Depth 400 mm x Height 450 mm 1 false table Rsdpfx Ahezw Ax Ijgecf Lubricant pump Voltage: 380 V Length: 1500 mm Width: 900 mm Total height in height position: 2300 mm Weight: approx 1,2 T

Condition: used, Radial Drilling Machine SCHLUMBERGER type RF6 Manual raising Cone: CM4 Rjdpfxezw Axzj Ahgjcf Spindle speed: from 35 to 1800 RPM Table size: 1000 x 650 mm Column slide travel along bed: 750 mm Maxi distance spindle nose/table: 700 mm (in high position) Mini distance spindle nose/table: 250 mm (in low position) Manual up/down of table + column Automatic descent Rotation at 360° on column Hydraulic column locking Drilling / tapping function Lubricant pump Voltage: 380 V Width: 1400 mm Depth: 900 mm Height in low position: 2650 mm Height in high position: 3000 mm Weight: approx 3 T

Condition: used, Radial Drilling Machine GSP type 44 T 12 Spindle: CM4 Spindle exit: 300 mm Arm travel: 1000 mm Max height swivel table/spindle nose in height position: 700 mm Max height table/spindle nos ein height position: 1300 mm Swivel table +/- 90 Swivel table dimensions: 1000 x 400 mm Spindle motor: 3,7 kW False table Length 1000 mm x Width 800 mm Auto descent Mechanical locking Lubricant pump Spindle rotation left/right Rotation at 360° around the column Voltage: 380 V Length: 2100 mm Width: 1000 mm Total height in height position: 2700 mm Total height in low position: 2400 mm Rcedjzw Axnopfx Ahgjf Weight: approx 2,5 T

Condition: used, Radial Drilling Machine GSP type 49S22 Spindle: Ø 125 mm Cone: CM6 Spindle exit: 600 mm Spindle speed: from 17 to 1050 RPM Arm travel: 1800 mm Maxi height column travel: 1800 mm Rcsdezw Atxopfx Ahgef Column diameter: Ø 600 mm Total column height: 3000 mm Spindle speed: 11 kW Drilling/tapping function Mechanical locking of the column Hydraulic locking of the trolley Auto descent Delivered with one cube Cube dimensions: L 800 x W 560 x H 600 mm Table size: L 3300 x W 1400 x H 320 mm Voltage: 380 V Weight: 12 T

Condition: used, Year of construction: 1990, Radial Drilling Machine KOLB KR 55 Year of construction: 1990 Spindle Ø 80 mm Cone CM5 Spindle exit: 400 mm Rotation: from 18 to 2000 RPM Table size: 1800 x 1000 mm Arm travel: 1250 mm Auto descent Auto rise according to the 0 setting Maxi distance spindle nose/table: 1500 mm Mini distance spindle nose/table: 800 mm Column diameter: Ø 315 mm Drilling/tapping function Rotation at 360° Possibility of sensory drilling Automatic gearbox Lubrification Hydraulic locking Voltage: 380 V Dimensions (L x W x H): 2900 x 1100 x 3060 mm Rcedpfx Ajzw Aqkehgef Weight: approx 5 T

Condition: used, Year of construction: 1990, Radial Drilling Machine Z3050 x 16 I Rcedpfx Ahezw Ap Togjf Spindle: Ø 80 mm Spindle exit: 300 mm Spindle speed: from 25 to 2000 RPM Arm travel: 1600 mm Year of construction: 1990 Column diameter: Ø 320 mm Maxi distance spindle nose/table: 1800 mm Mini distance spindle nose/table: 1200 mm Table useful dimensions: 1700 x 1000 mm Tailstock CM5 Hydraulic clamping trolley + arm + column Auto advance non-functional Lubricant pump Voltage: 380 V Dimensions (L x W x H): 2400 x 1200 x 3200 mm Weight: approx 4 T

Condition: used, Year of construction: 1998, total width: 1,100 mm, total length: 1,700 mm, total height: 1,150 mm, Colour: White Empty weight: 1.100 kg - Year: 1998 - Documentation available: No Rjdozvx N Hopfx Ahgecf - CE marking present: Yes - CE certificate present: No - Serial number: 980223 - Table length [mm]: 245 - Table width [mm]: 735 - Number of spindles [pcs]: 8 - Spindle diameter [mm]: 16 - Max. spindle speed [rpm]: 17000 - Distance between spindles [mm]: 50 - Workpiece clamps [pcs]: 2 - Workpiece support/Guide: Table - Drills included: Yes - Voltage [V]: 415 - Fuse [A]: 16 - Power [kW]: 7.5 - Transport dimensions: 1700mm x 1100mm x 1150mm (l x w x h) - Transport weight [kg]: 1100kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Drills Grinding Machine DECKEL SOE Spindle speed: 4500 RPM Maxi bore of clamps: 17,5 mm Rcodpjzww Ttefx Ahgjf Maxi sharpenable radius: 10 mm Maxi lateral displacement: 10 mm Angle adjustment: 45° Maxi displacement: 100 mm (see technical details) Delivred with 1 set of clamps + different diamond grinding wheels Voltage: 380 V Width: 600 mm Depth: 600 mm Total height: 1300 mm Weight: approx 150 kg

Condition: good (used), Please refer to the images for all technical specifications. Transport and loading can be arranged throughout Europe for an additional charge upon request. Prices are subject to VAT. Viewing is possible by appointment. Contact us—our team looks forward to assisting you. Machinery purchase / sale Rcedpfozvnnfex Ahgof PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES, MACHINE TOOLS, AND MUCH MORE. Do you need a high-quality yet affordable machine for your production? Or are you looking to sell yours? For further information or contact options, please reach us via the contact form.

Condition: new, Year of construction: 2026, Threading unit OLED display LED lighting Continuous/normal drilling capacity (mm) - R1 27/32 mm - R2 25/30 mm Maximum threading capacity - R1 M34x3 - R2 M20x2,5 Spindle MK III Drilling depth (mm) 125 Overhang (mm) 300 Column diameter (mm) 125 Usable table surface (W x D) (mm) 590 x 450 Speed display digital Drilling depth display digital Drilling depth stop with fine adjustment Table height adjustment with rack and pinion Spindle/table (mm) 150-700 Machine dimensions without control panel (mm) 610 x 900 x 1,980 mm Machine dimensions Redpfott Af Rox Ahgjcf with control panel (mm) 670 x 1,100 x 2,140 mm Spindle speeds, stepless R1 (1-stage) 0-1000 rpm R2 (1-stage) 0-1600 rpm Feed by hand Weight (kg) 370 Optional drilling package 5 (€875.00 plus VAT) - Vise [felix] 2.0 150 - Tapered mandrel MK III/B18 - Reducing sleeve MK III/MK I - Reducing sleeve MK III/MK II - Quick-change drill chuck B18 3-16 mm (accuracy 0.17 mm) Delivery in Germany, including packaging, free to your door! NOT THE RIGHT MACHINE? WE ARE A FLOTT SUPPORT PARTNER AND CAN OFFER YOU ALL PRODUCTS FROM THE FLOTT RANGE! ASK FOR A QUOTE!

Condition: used, Year of construction: 1972, Technical details: bore capacity in steel (diameter): 25 mm throat: 300 mm bore stroke: 630 mm Rcsdpszfltdofx Ahgsf spindle turning speed - continuous: 150 - 2860 U/min spindle taper MT: MK 4 Distance spindle/table max.: 630 mm table-size: 300 x 400 mm total power requirement: 1,65 kW weight of the machine ca.: 700 kg dimension machine approx.LxWxH: 0,6 x 0,8 x 2,10 m

Condition: used, Year of construction: 2011, Technical details: bore capacity in steel (diameter): 35 mm throat: 350 mm bore stroke: 180 mm threading: ST M 24 mm spindle taper MT: MK4 spindle speed:: 50 - 1450 U/min Distance spindle/table max.: 780 mm table clamping surface:: 560 x 560 mm weight of the machine ca.: 500 kg dimension machine approx.LxWxH: 0,73 x 0,56 x 0,22 m · Heavy, solid cast construction · Automatic gear lubrication via oil pump · Smooth running due to ground gearbox gears operating in an oil bath Rcjdeyli Sfopfx Ahgef · High concentricity thanks to hardened and ground main spindle · Thread cutting device · Lockable main switch and motor protection switch · Optidrill B 40GSM additionally with automatic quill feed · Electric · 2 feed rates: 0.1 / 0.2 mm/rev · Coolant system · Drilling depth stop · 18 speeds: 50 – 1,450 rpm · 9 selectable speeds via gearbox lever on the front of the drill head *

Condition: used, Year of construction: 1997, Technical details: bore capacity in steel (diameter): 32 mm x-travel: 750 mm y-travel: 520 mm drill capacity in cast iron: 45 mm revolution per minute: 90 - 4500 U/min feed steps: 6 bore spindle stroke: 250 mm boring spindle diameter: 30 mm drill spindle - Morse Taper: MK4 vertical adjustment of the arm: 520 mm throat max.: 1000 mm throat min.: 250 mm column diameter: 400 mm swivel range of the arm: 180 ° table clamping surface LxW: 1150 x 800 mm total power requirement: 3,5 KW weight of the machine ca.: 2000 kg dimension machine approx.LxWxH: 1,7 x 1,07 x 2,61 m The KOVOSVIT VO 32 is a robust and versatile radial drilling machine designed for industrial applications. The machine is suitable for drilling, boring, countersinking, reaming, and tapping operations in steel, cast iron, and other materials. Thanks to its swiveling radial arm and large reach, even large and heavy workpieces can be machined conveniently without the need for complex repositioning. The machine features a massive cast-iron construction, a powerful main drive, and an automatic feed system. The drilling head can be moved along the radial arm, providing a large working area. Its solid design ensures high precision, reliability, and a long service life, even under continuous operation. Redpfx Aszgwgfohgecf Equipment: ·Including coolant pump ·1 × boring tool block (boring cube) ·1 × machine vise *

Condition: new, Year of construction: 2026, functionality: fully functional, power: 4 kW (5.44 HP), input voltage: 400 V, input current: 16 A, input frequency: 50 Hz, actuation type: electric, rotational speed (max.): 3,100 rpm, rotational speed (min.): 700 rpm, total width: 1,487 mm, total length: 4,440 mm, total height: 2,793 mm, throat depth: 1,490 mm, overall weight: 1,900 kg, Equipment: CE marking, documentation/manual, NEW | YEAR 2026 | CE CERTIFIED | MADE IN POLAND | EXW €38,000 + VAT Rsdpfx Aeh Ek H Sshgscf WHY THE PRIAM The Priam is a vertical, electronically controlled glass drilling machine that does most of the work for the operator. The entire feed is electronically controlled — drilling is smooth and repeatable. The operator's role is minimal. After mounting the hole saws, they press the "Calibration" button — the machine measures the length of both drills (front and rear) and their diameter, then automatically assigns the correct spindle speed. After every drill change, the machine will not start drilling until calibration is done — setup errors are impossible. The hole position on the vertical axis is entered on the monitor and the support bar travels there automatically (up to 1,060 mm below the spindle axis); horizontally, the glass is positioned against 6 stops. The machine does the rest: the pneumatic clamp measures the glass thickness, the rear spindle pre-drills to a depth calculated by the controller, and the front spindle completes the hole from the other side — chip-free, clean edges at the first attempt. Optional: double-sided chamfering (hole saw with chamfering ring), tapered holes, and pulse drilling mode for laminated (VSG) glass. BUILT FOR SERIAL PRODUCTION Up to 20 holes on the vertical axis can be programmed — the operator enters the dimensions once and the machine drills them automatically. In serial production (shower enclosures, balustrades) the following panes are drilled without re-entering positions. Drilling at position 0 on the support bar allows holes on the glass edge (half-moon cut-outs). Performance: a Ø 75 mm hole in 4 mm glass in approx. 25–30 s (feed in glass approx. 1 mm/s, speed set by the operator). Recommended: thin-wall, self-sharpening hole saws (e.g. Champion, L=75 mm). TECHNICAL DATA Drilling diameter range: Ø 5–80 mm (both drills same diameter) Glass thickness: 2–20 mm Max. pane size: 2,000 × 4,000 mm, up to 200 kg Support bar travel: up to 1,060 mm below spindle axis Holes on the glass edge (half-moon): yes, position 0 Drilling program: up to 20 holes on the vertical axis Spindle speed: adjustable 700–2,800 RPM, assigned automatically after calibration Feed: automatic, electronically controlled Cooling: closed water circuit, approx. 30 l Compressed air: 6 bar (pneumatic clamping) Power supply: 400 V / 16 A / 4 kW Machine dimensions (L × W × H): 4,440 × 1,487 × 2,793 mm Weight: 1,900 kg Scope of delivery: CE marking, documentation, operating manual MANUFACTURER, SERVICE, TERMS EXPOGLASS is a Polish manufacturer of glass processing machinery — built at our own factory in Nysa (in-house welding shop and powder coating). Service with online support; spare and wear parts available from stock. Delivery and commissioning across the EU, operator training on site. Delivery time: approx. 8 weeks. Warranty: 12 months. Visit our factory and see the Priam drill your own glass samples before you buy — video of the machine in operation in this listing. Glasstec 2026, Düsseldorf, 20–23 October, Hall 12, Stand 12A72.

Year of construction: 2023, condition: used, Dimensions (LxBxH): 110 x 55 x 150 cm Serial number: SMK2023072160K-1 Power: 30W Working area: 110x110mm Overall dimensions LxWxH: 1100x550x1500mm Online auction of metalworking and sheet metal processing machines (including a wide selection of SIEGMUND welding and clamping tables and related tools, SAFAN press brakes and SAFAN guillotine shears, MOSMAN YLS-3000 3kW laser welding machine, various FRONIUS, REHM, etc. welding machines, BOMAR, URSUS, ELHA, etc.), remaining stock of sheet metal, materials and inventory, rolling stock, technical equipment, and modern office furniture, released following the recent bankruptcy of Solex Thermal Science (Netherlands) B.V., formerly Mosman Stainless Steel in Haaksbergen, the Netherlands. The online auction opens Thursday 16 July and closes Thursday 3 September. Register your account via our website and place your bid. For viewings and inspections check the auction information on the website. Viewing day is on: - Tuesday 1 September Pickup days are on: - Thursday 10 September - Friday 11 September Dome Auctions is an innovative auction platform dedicated exclusively to the industrial sector. By focusing on machinery sales from business closures, restructurings, and bankruptcies, we provide a trusted marketplace where buyers and sellers connect with confidence. Unlike general auction houses, Dome Auctions specializes in selling complete industrial assets directly from factories, ensuring quality and reliability. With a commitment to transparency, industry expertise, and tailored service, we streamline the sales process and maximize value for all parties. As online auctions continue to grow in the European industrial market, Dome Auctions offers a professional and efficient solution for companies seeking high-quality machinery at competitive prices. Rcodozm H Acepfx Ahgjf

Condition: used, Year of construction: 2014, Used Machine Year of manufacture: 2014 Condition: The machine has been factory-overhauled by Ganner Features and Technical Specifications: Complete standard configuration including: - Support with linear guide consisting of: 1 single-spindle horizontal drilling unit, 0.65 kW motor, 70 mm stroke Tool speed selectable via operator software (3000/5000/8000 rpm) 1 blow-out, gluing, and dowel-driving station for dowels Ø 8 mm, dowel length 25–50 mm - Fully automatic, electronically controlled central lubrication - X-axis NC-controlled, with working length 1300 mm, travel speed max. 105 m/min. - Z-axis manually adjustable via mechanical digital counter, position adjustable via support table 5–40 mm - Dowel drive-in overhang adjustable from 7–20 mm via a mechanical digital counter; drilling depth from 0–35 mm (for drill bit length GL 70 mm) is automatically adjusted with the drive-in overhang - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with a viscosity of 150 to 350 mPas - Glue quantity continuously adjustable via operator software - GLUE/WATER selector switch for flushing the glue system, each with: 1 stainless steel tank for 7.5 kg of glue and 7.5 l of water - Indicator light showing remaining glue levels in the glue tank - 1 left side stop, 1 right side stop, and 1 center stop (all removable) - 4 start buttons for individual processing of 1–4 workpieces - 4 pneumatic 10° angle clamping cylinders for workpiece thicknesses up to 80 mm, workpiece length (Y) min. 70 mm - 1 extraction funnel, connection Ø 80 mm - 1 TCT control unit with: Built-in industrial PC, including Beckhoff TWINCAT soft PLC, operating temperature range 0–50°C, 15-inch capacitive TFT industrial touchscreen, operating system: WINDOWS 7 - Programming via menu-driven user software, drilling distances freely programmable with ABSOLUTE, RELATIVE, or GRID dimensions, automatic workpiece mirroring and operation optimization, 4 work areas assignable to different programs, graphical workpiece display, parametric programming, zero-point offset, programmable worklists, error diagnosis with plain text Optional equipment: - 1 electronic, optical glue monitoring system G.I.C. (Glue Insert Control) for 1 glue nozzle - 1 Z-axis with NC-controlled, dynamic positioning for height adjustment of the drilling and dowel-driving station (programmable from 5–40 mm), travel speed max. 30 mm/sec. - 1 single-spindle vertical drilling unit drilling from the TOP, 0.65 kW, (3000/5000/8000 rpm), position (Y) manually adjustable via a mechanical digital counter from 5–40 mm, drilling depth (Z) max. 30 mm (with drill bit length GL 57 mm), Workpiece thickness (Z) max. 50 mm, workpiece length (Y) min. 130 mm (including drilling depth compensation, e.g., for Häfele Minifix) - 4 vertical 10° angle clamping cylinders with mount - 1 keypad with mount Rcsdpfx Ahezlbrvogjf Availability: available shortly Location: DE-63934 Röllbach

Condition: new, 6-sided drilling machine Manufacturer: Quick Type: KQ-63E New machine Technical data: - Workpiece length: 70 - 2800 mm - Workpiece width: 50 - 1220 mm - Workpiece thickness: 9 - 60 mm - Min. workpiece to be processed: 70 x 50 mm - Feed rate in X: 135 m/min - Feed rate in Y: 90 m/min - Feed rate in Z: 25 m/min - Individually controllable spindles: Top: 2 x 12 vertical, 4 horizontal / Bottom: 1 x 7 vertical - Machine control: Higerman (German) - Milling spindle (top): 9 kW, 24000 rpm - Tool changer (top): 5-position - Milling spindle (bottom): 3.5 kW, 18000 rpm - Motors: Brushless servo motors - Positioning accuracy: 0.03/1000 - Repeatability: 0.02/1000 Optional: - Machine with workpiece return Quickly found Offer machines Register for newsletter Unsubscribe from newsletter Contact us Rcodpszvgn Djfx Ahgof Overview

Condition: new, Six-sided drilling machine Manufacturer: Quick Type: KQ-62Lite New machine Technical data: Redpfx Ahozvgndogocf - Workpiece length: 70 - 2,400 mm - Workpiece thickness: 9 - 60 mm - Workpiece width: 30 - 1,220 mm - Min. processing size: 50 x 70 mm - Transport speed in X: 138 m/min - Transport speed in Y: 90 m/min - Transport speed in Z: 28 m/min - Machine control: Higerman - Working height: 890 mm - Milling spindle: 2 x 3.5 kW, 18,000 RPM, manual tool change - Drilling unit: Top 9 vertical and 4 horizontal / Bottom 7 vertical - Positioning accuracy: 0.03/1000 - Repeatability: 0.02/1000 - Power consumption: 25.8 kW Optional - Machine including workpiece return Other configurations available upon request.

Condition: good (used), *FOR SALE: Cincinnati Milacron PTC 40 Column Drill – 1982* *Price:* €2,200 – Negotiable *Location:* Les Ponts-de-Cé, 49130, Pays de la Loire *Description:* Industrial column drill *CINCINNATI MILACRON PTC 40*, manufactured in 1982. French made. Very robust machine for drilling and tapping in mechanical and sheet metal workshops. Column with cross table mounted on slides. Remote control + foot pedal. Complete and fully operational machine. *Specifications:* - *Make / Model*: CINCINNATI MILACRON PTC 40 380V Rcodpfx Ahozvgr Asgof - *Year*: 1982 - Serial No. 45117 - *Type*: Column drill on a base - *Table*: Cross table mounted on slides - *Feed*: Spindle descent via handwheel + lever - *Equipment*: Remote electrical cabinet, Foot pedal, Vises - *Mounting*: On a pallet for removal

Condition: new, Year of construction: 2023, machine/vehicle number: 320542/B, functionality: fully functional, number of axes: 3, controller manufacturer: TPA, CNC Drilling and Milling Machine Manufacturer: Vitap Type: K3 New machine Through-feed processing, workpiece machining from below, and automatic workpiece return to the operator Develop an individual class: - With this machine, you can perform many different milling operations in addition to grooving and drilling, from simple edge milling to milling shapes and letters. - We do not limit your creativity. Easy entry into CNC technology: - TPA makes it easy for you: Whether drilling, grooving, linear milling, contour milling, or milling letters. - The CAD software clearly displays the machining operations. - Particularly clear is the programming of the work steps on the individual workpiece sides. - You can mirror machining operations with a mouse click. - You can either enter the starting points precisely or determine them by clicking on the virtual workpiece. Vitap Bar Nesting - efficient and time-saving - This patented software produces entire corpus elements from a long workpiece. - You insert the long workpiece, and when you remove the first finished element, the machining of the next element continues directly. The DDT feed system (double dynamic transport) - 2 clamps enable uninterrupted workpiece transport. - The operator inserts the workpiece until it reaches the stop. - Both clamps then grip the workpiece and position it precisely. - During machining, both clamps communicate with each other, so that clamp 2 grips before clamp 1 releases. - This ensures a constant feed rate even during linear milling. 3 controlled axes: Rcodjzvduuepfx Ahgjf - X axis - DDT feed - Y axis - Drilling head travel - Z axis - Drilling - Double "0" reference: New laser generation for detecting the beginning and end of the workpiece. The program can readjust the drilling from below to achieve perfect alignment in vertical and horizontal workpieces. The laser consists of a transmitter and receiver to avoid errors with dark edge material. - Side stops with rollers, consisting of a fixed and a movable part, mechanical digital readout with automatic alignment to the 0 stop for removal of up to 3 mm on the 0 line - Constant side pressing device for precise positioning to the 0 line - Automatic 4-position tool changer - Adjustable zero point - No workpiece length limitation - Monitor LCD TFT 20" - Industrial PC - Operator interface WSC with Lister, parametric tool, and parametric setup - Graphical programming CAD TPA EDI32, basic version - USB port - Storage of all files - Macro programming - Import DXF files Technical data - Number of independent, vertical spindles: 12 - Number of independent, horizontal spindles on the X axis: (2+2) - Number of horizontal drilling spindles on the Y axis: (2+2) - 1 saw (100mm) - Electro spindle 5 kW with ISO30 taper (RPM [contact removed]) - Max. workpiece weight: 40 kg - Max. workpiece dimensions: X unlimited, Y 1250 mm, Z 50 mm - Min. workpiece dimensions: X 270, Y 150 (70op), Z 3 mm - Feed rate: 25 m/min - Spindle speed: 3600 RPM - Saw speed: 7000 RPM - Max. horizontal tool: 12mm - Max. drilling depth horizontally on the X and Y axis: 35mm - Max. drilling depth vertically: 43 mm - Max. vertical tool: 35mm - Motor: 1.7 kW - Adjustable zero point for 4-sided formatting - CE compliant Optional against additional charge