Used Driving for sale (21,134)

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: Csdpfx Abex Dnb Uo Tehf The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), power: 60 kW (81.58 HP), gearing type: hydrostat, fuel type: diesel, lifting height: 9,000 mm, Year of construction: 1994, operating hours: 8,172 h, Equipment: additional headlights, all wheel drive, cabin, pallet forks, Vehicle Description Telescopic Loader MERLO P25 9EVS Year of manufacture: 1994 According to the hour meter: 8,175 hours 2.5-ton lifting capacity 9-meter lifting height Perkins engine 2-speed hydrostatic drive - incl. forks - incl. bucket - hydraulic quick coupler - auxiliary hydraulic circuit to the fork carrier Codpsx Dm Eljfx Ab Tohf - hydraulic self-levelling - all-wheel drive - 3 steering modes - cab with heating - lighting system - incl. road registration NL! - nice machine! - good tires! - old but good! Affordable delivery possible!

Condition: excellent (used), functionality: fully functional, Max. air flow rate: 800 m³/h Max. negative pressure: 1,800 Pa Suction connection: 150 mm Suction connection height: 300 mm Drive power: 1.10 kW Connection voltage: 220 / 380 volts (4.33 / 2.5 amps) Dimensions (L/W/H): 610 x 740 x 1,150 mm Total depth: 670 V Sound pressure level: 72 dB(A) Weight: 70 kg • Includes flexible suction arm • Suitable for almost all types of dust • Cleanable, durable bag filter Chjdsx Dmr Sepfx Ab Tsf

Year of construction: 2013, condition: used, Empty weight: 170 kg Lifting capacity: 295 kg Lift height: 730 cm CE mark: yes General condition: good Technical condition: good Visual appearance: good Transport dimensions (LxWxH): 0,87x0,78x2,21 Please contact Christian Theißen for more information Manufacturer: Genie Model: SLC24 Year of build: 2013 Condition: Used Data: Max. lifting height: 7,30 m Lifting capacity: 295 kg Drive type: manuell Dimensions LxWxH: 2,08 x 1,67 x 2,21 m Transport dimensions LxWxH: 0,87 x 0,78 x 2,21 m Platform dimensions LxW: 0,57 x 0,67 m Own weight: 170 kg Chjdsx Dmhmepfx Ab Tof Special features: Mounted on rollers, lifting function via hand crank.

Condition: good (used), Stop for press brake, edging bench, guillotine shears, drive shaft Chsdegxnkkopfx Ab Tef -Drive shafts: for stop, from press brake EHT type EHP 11-40 2 pieces -Length: 515 mm -Socket: Ø 25 mm -Price: complete -Dimension: Ø 50 x 515 mm -Weight 5.1 kg / pc.

Condition: used, Eyelets diameter: Standard 6 mm (optional 5–5.5 mm) Material: Cardboard, paperboard, plastics Drive: Maintenance-free brake motor Eyelets feed: Automatic to upper tool Working depth: Approx. 130 mm Csdox Dmaijpfx Ab Tohf Activation: Electric foot switch

Condition: like new (used), Year of construction: 2021, operating hours: 5 h, load capacity: 1,000 kg, lifting height: 3,227 mm, fuel type: electric, mast type: duplex, construction height: 2,247 mm, empty load weight: 650 kg, mileage: 5 km, This 2021 STILL electric stacker is in like-new condition; The stacker has a capacity of 1,000 kg; Lifts up to a height of 3,227 mm; The drive-through height is 2,247 mm; ONLY 5 hours on the meter; The battery is equipped with an INTERNAL charger and an automatic filling system; Order the stacker via our webshop or schedule an appointment for a test drive! Video to follow. Cjdpfx Ajx Dmdbsb Tjhf

Condition: excellent (used), TECHNICAL DATA - Shaft width: 500 mm - Number of knives: 4 pcs - Max thickness of the processed workpiece: 230 mm From above: - Pawls - Serrated, driven, sequential infeed roller - Pressure units - Planing shaft - Pressure unit - Smooth, driven outfeed roller From below: - Adjustable driving rollers in the lower table: 2 pcs - Motor: 5.5 kW - Electrically operated table lift Cedpfx Aeqv Aivjb Tohf - Table lift motor: 0.37 kW - Infinitely variable feed speed regulation - Extraction nozzle diameter: 150 mm - Dimensions (LxWxH): 1000x1000x1350 mm - Weight: 690 kg ADVANTAGES – Electric table lifting – 4-knife shaft – Driving rollers in the lower table – Used thicknesser, in very good condition Net price: 16,900 PLN Net price: 4,020 EUR at a 4.2 EUR exchange rate (Prices may vary with exchange rate fluctuations)

Condition: good (used), Year of construction: 1995, functionality: fully functional, Control system: SIEMENS 840D Solution Line (electrical overhaul in 2017) X-travel: 7,000 mm Y-travel: 2,100 mm Z-travel: 1,500 mm Z-travel (spindle in vertical position): 1,200 mm Feed rate X, Y, and Z axes: 2–12,000 mm/min Rapid traverse speed X, Y, and Z axes: 12,000 mm/min Universal milling head UFKSpindle speeds: 22 - 2,400 rpm Drive power 100 / 60 ED: 31.5 / 39 kW Max. torque main spindle: 2,200 Nm Swivel range of milling head (C axis): 180° Swivel range of milling head (A axis): 340° PREISELER AWU 650 automatic reversible clamping device Year of manufacture: 1995 with FORKARDT F630 vertical three-jaw chuck: 630 mm Center height above plate: 500 mm Max. workpiece weight (clamped in flight): 2,000 kg Chodpfx Aox Dmrljb Tjf Max. workpiece weight (with counter bearing): 4,000 kg Counter bearing with hydraulic quill Tailstock quill taper: MK6 Tailstock center height: 500 mm Clamping plate Dimensions (LxWxH): 6,000 x 1,500 x 300 mm Max. load: 90 t T-slots: 6 pieces 28H7 (DIN650) T-slot spacing: 250 mm Coolant system with paper belt filter Manufacturer: ALLWEILER AG Type: PF 60 DVS / 500 Pump capacity at max. 3 bar: 40 l/min With recirculation unit Equipped with Automatic turning clamp with worm gear: PEISLER AWU650 Various roller blocks and supports6 UK500 machine clamping tablesMAYFRAN TYPE MT10 hinged belt conveyor SIEMENS SINUMERIK HT2 electronic handwheel Milling head design with hydromechanical rapid tool clamping Direct contactless measurement via linear measuring systems Oil circulation lubrication for main gearbox and milling head drive Work platform traveling in X direction, protective cover with viewing windows The machine is in exceptionally good condition and can be viewed under power. In 2017, a new SIEMENS 840D Solution Line control system was installed, and all drive motors and the control cabinet were replaced.

Condition: used, Year of construction: 2007, lifting height: 6,100 mm, fuel type: electric, Weights Empty weight: 1.826 kg Functional Lifting capacity: 363 kg Working height: 810 cm CE mark: yes Condition General condition: average Technical condition: average Visual appearance: average Other information Delivery terms: EXW Csdsx Dmhgepfx Ab Tohf Transport dimensions (LxWxH): 2,25x0,78 Production country: US Additional information Please contact Christian Theißen for more information Manufacturer: Genie Model: GS2032 Year of build: 2007 Condition: Used Data: Max. working height: 8,10 m Platform height: 6,10 m Lifting capacity: 363 kg Lifting capacity on extension: 113 kg Platform dimensions LxW: 2,25 x 0,78 m Platform lenght pushed out: 3,25 m Height transport position with/without railing: 1,97/1,23m Total dimensions LxW: 2,44 x 0,81m Movable up to working height: 8,10 m Ground clearance: 0,11 m Drive type: Batterie Own weight: 1.826 kg Special features: White tires, attachment points for personal protective equipment (PPE) present, indoor use only.

Condition: good (used), Motor control, controller, converter, stepper drive, stepper motor control, frequency converter, motor controller, servo drive controller -Manufacturer: Festo, Motor Controller -Type: CMMS-AS-C4--3A G2 572986 -Number: 6 controllers available -Price: per piece -Dimensions: 310/60/H180 mm Chsdpfx Abop E Hz Tj Tof -Weight: 1.4 kg/pc.

Condition: used, Year of construction: 1962, Banbury Kneader / Mixer #3 with peripheral equipment Documented modifications / upgrades: Year Modification / Upgrade 1962 Gearbox upgrade Kneader III 1973 Carbon black weighing & dosing system for Kneader III 1981 Exhaust extraction system for Kneader III 1985 Batch-Off machine for Kneader 3 1985 Temperature control unit for Kneader 3 1995 DC motor 1500 HP, 1700 V, 1678 A 1996 Upgrade to KSBI-L270 Kneader III 2007 Hose scale for Kneader #3 2008 Vibration measurement system Mixer III 2008 Column-mounted slewing crane for bale handling Mixer III 2009 Vacuum hoist system Kneader III 2010 CMS system for Mixer III 2013 Long-strip cutting device for Kneader III 2014 Slab feeder for Kneader III 2014 Overnose conveyor Kneader III 2014 2 × floor scales for Kneader III 2014 New control system for Kneader III 2014 Cooling register MUAFAN 1+2 – cooling line mill Kneader 2+3 2015 Monitoring system (Kneaders I–III) for CMS Kneader III 2017 Mixer body replacement Kneader III 2023 Rubber kneader III KSBI-L270 Control system: New control system 2014, CMS system 2010, DC Drive / Automax, PLC Batch-Off & Conveyor, AC Drives documented Maintenance / condition: Regular modernizations and upgrades documented 1962–2023 Accessories / options: Batch-Off machine, slab feeder, put-up conveyor, long-strip cutter, floor scales, bale handling crane, vacuum hoist system, carbon black silos & weighing system, extruder, roller die, roller head with conveyor, cooling systems (dip tank, cooling line, laydown), control systems (DC Drive, AC Drive, Automax, PLC) Chjdpfx Ajxb T T Rsb Tsf

Condition: used, total length: 2,200 mm, total width: 1,100 mm, total height: 1,500 mm, Empty weight: 2.000 kg - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Drive system: Conventional - Power [kW]: 3.8 - Centre height [mm]: 180 - Swing over bed [mm]: 350 - Carriage turning diameter [mm]: 200 - Distance between centres [mm]: 750 - Bed width [mm]: 260 - Spindle bore [mm]: 52 - Min. spindle speed [rpm]: 40 - Max. spindle speed [rpm]: 2500 - Max. workpiece weight [kg]: 250 - Transport dimensions: 2200mm x 1100mm x 1500mm (l x w x h) - Transport weight [kg]: 2000kg Csdpfxex Dkibo Ab Tehf - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: excellent (used), CATALOG NUMBER 6950 TECHNICAL DATA - Maximum workpiece width: 220 mm - Maximum workpiece height: 130 mm – 4 spindles: 1) Horizontal bottom, 220 mm, 5.5 kW 2) Vertical right, 130 mm 3) Vertical left, 130 mm; (spindles 2 and 3) 5.5 kW 4) Horizontal top, 220 mm, 5.5 kW - 4 electrically adjustable spindles (up/down) - All spindles adjustable up/down, right/left - Spindle diameter: 40 mm - 4 upper infeed drive rollers, gear-driven, including 1 double roller - 1 double upper outfeed drive roller, rubber-coated - Lower outfeed drive roller, rubber-coated - Feed via Cardan shaft rollers - Infinitely variable feed speed: 6–22 m/min - Feed motor: 2.2 kW - Lifting motor: 0.55 kW - Electric planing thickness adjustment - Infeed table length: 1970 mm - Central lubrication system - Extraction port diameter: 3x120 mm, 140 mm - Enclosed in cabin - Dimensions (LxWxH): 3350 x 1400 x 1400 mm - Weight: 1700 kg – German-made – Unpainted – Used planer, very good condition Csdjlikzfopfx Ab Tshf Net price: 38,900 PLN Net price: 9,260 EUR Net price calculated at exchange rate of 4.2 PLN/EUR (In case of significant exchange rate fluctuations, the price may change)

Condition: good (used), Year of construction: 1997, Clamping Unit: Clamping force: 7,000 kN Csdpfx Asx Dmp Rob Tehf Operating pressure: 250 bar Specific pressing pressure: 610 N/cm² Number of levels: 2 Installation height with 75 mm heating plate & 20 mm insulating plate: approx. 2x 190 mm Piston stroke: approx. 400 mm Piston 1 diameter: 543 mm Clamping force, rapid traverse: approx. 2 x 85 kN Retraction force: approx. 2 x 47 kN Operating pressure: 300 bar Piston 2 diameter: 60/40 mm Stroke: 400 mm Estimated weight: approx. 16 tonnes Hydraulic System: Pressure adjustment: 40 - 300 bar Flow rate regulation: 0 - 99 % Flow rate l/min (HD): 45 against 300 bar Drive power: 22 kW Tank dimensions (LxWxH): 1000 x 770 x 535 mm Closing Speed: Rapid traverse: approx. 40 - 50 mm/s Slow closing: approx. 0 - 20 mm/s Pressing speed: approx. 0 - 3 mm/s Slow opening: approx. 0 - 20 mm/s Opening, rapid traverse: approx. 0 - 60 mm/s

Condition: good (used), Year of construction: 2014, mast type: telescopic, fuel type: diesel, Weights Empty weight: 6.600 kg Functional Lifting capacity: 230 kg Working height: 1.570 cm CE mark: yes Condition Technical condition: good Visual appearance: good Other information Delivery terms: EXW Csdpfx Abjx Dmhaj Tohf Max. horizontal reach: 1250 m Max swing of arm in degrees: 360 Transport dimensions (LxWxH): 8,4x2,26x2,24 Production country: FR Additional information Please contact Christian Theißen for more information Manufacturer: Haulotte Model: H16TPX Year of build: 2014 Condition: Used Data: Max. working height: 15,70 m Max. platform height: 13,70 m Max. reach: 12,50 m Drive type: Diesel Total dimensions LxWxH: 8,40 x 2,26 x 2,24 m Length of transport position: 6,60 m Height transport position: 2,50 m Track widining: 0 m Platform dimensions LxW: 1,81 x 0,78 m Max. basket load: 230 kg Swivel range: 360° Overhang: 0,88 m Movable up to working height: 15,70 m Max. Pitch angle: 50% Wheel pressure (Support pressure): 41 kN Ground clearance: 0,25 m Own weight: 6.600 kg Special features: Rotating work basket, basket arm/vertical rotation angle 140°, all-wheel drive, differential lock, permanently installed soot filter.

Year of construction: 2001, condition: ready for operation (used), Shot Blasting Machine, PARTICLE BLASTING MACHINE, Shot Blaster Units, , Schlick Particle Blasting, Roto-jet, Used Machine Manufacturer: USF SCHLICK, Heinrich Schlick Model: Roto-Jet, 24/23457 Year: 2001 Installation dimensions: 4560 x 3920 x 5080 mm Electrical Cabinet, PLC: - Siemens S7 1200 - Servomotor Controller 2 - Siemens Simatic HMI Display - 400 V ; 20 A Particle Blasting Chamber: Chedpjrk D Tnofx Ab Tef Equipped with a servomotor, which synchronously drives the rotating table and the screw conveyor. Another servomotor provides the vertical movement of the particle sprayers. The chamber is lined and has doors that can be opened from multiple sides, with one side having a lifting opening. Table size: 900 mm in diameter. Maximum object size that can be placed: 1000 mm x 1000 mm in diameter Extraction System: Ensures the extraction of dust resulting from spraying, which it can perform in its own airspace. Equipped with bag filters on the exhaust side and cartridge filters on the extraction and dust separation side. Cup-type Distributor and Particle Sprayer Tank: The cup-type distributor transports the shot to a collector after the screw dispenser, which has a 3-stage filter for cleaning the particles (vibrating filter). The tank has outlets where the dosage of particle spraying can be regulated. - It is possible to connect to 10 adjustable particle spraying points. - Currently, 5 particle spraying points are connected.

Condition: used, total length: 1,700 mm, total width: 800 mm, total height: 1,500 mm, Empty weight: 1.000 kg - Documentation available: Yes - CE certificate present: No - Drive system: Conventional - Centre height [mm]: 150 - Swing over bed [mm]: 305 - Distance between centres [mm]: 750 - Bed width [mm]: 250 - Spindle bore [mm]: 45 - Min. spindle speed [rpm]: 50 - Max. spindle speed [rpm]: 2400 - Options: Three-jaw chuck - Transport dimensions: 1700mm x 800mm x 1500mm (l x w x h) - Transport weight [kg]: 1000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Codpfx Abox Dkh Rj Tshf Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: excellent (used), Catalogue number 6393 TECHNICAL DATA - Maximum workpiece width: 200 mm - Maximum workpiece height: 150 mm - Number of spindles: 4: 1) Bottom horizontal, 200 mm, 5.5 kW 2) Right vertical, 150 mm, 4 kW 3) Left vertical, 150 mm, 4 kW 4) Top horizontal, 200 mm, 5.5 kW - All cutterheads adjustable vertically and horizontally - Spindle diameter: 40 mm - Spindle speed: 6,000 rpm Chedpfehh Sflsx Ab Tof From above: - 6 feed-in traction rollers, toothed (including 2 double) - 1 feed-out traction roller, rubber-coated From below: - Feed-in drive roller, toothed, steering, integrated in lower table - 3 side pressure rollers - Feed-out traction roller, metal, smooth - All rollers pneumatically loaded - Infeed table length: 2,130 mm - Height-adjustable table - Centralized lubrication system - Electric adjustment of planing thickness - Lift motor: 1.1 kW - Stepless feed speed control via inverter - Feed drive motor: 3 kW - Feed via Cardan shafts - Fully enclosed in cabin - Extraction port diameters: 4 x 130 mm - Dimensions (LxWxH): 3,550 x 1,750 x 1,800 mm - Approx. weight: 3,000 kg ADVANTAGES – Equipped with 4 cutterheads – Ideal for wet and dry timber – DTR operation and maintenance manual included – Used machine, very good condition Net price: 65,900 PLN Net price: 15,690 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR (In case of significant exchange rate fluctuations, the price may change)

Condition: used, Year of construction: 2006, functionality: fully functional, Turning diameter: 650 mm Turning length: 1,500 mm Total power requirement: 33 kW Center distance: 1,500 mm Swing diameter over bed: 650 mm Swing diameter in recess: 670 Turning diameter: 650 mm Turning length: 1,500 mm Chsdox Dmntepfx Ab Tsf Total power requirement: 33 kW Center distance: 1,500 mm Swing diameter over bed: 650 mm Swing diameter in recess: 670 mm Swing diameter over face slide: 260 mm Face slide travel: 380 mm Main drive Drive power AC motor - 40/60/100% duty cycle: 33/27/22 kW Spindle box Spindle bore diameter: 106 mm Spindle diameter in front bearing: 140 mm Speed range (V constant): 1 - 2,000 rpm Cross slide Feed range, face: 0.001 - 1,000 mm/rev Feed range, face, optional up to: 5,000 mm/rev Feed range, longitudinal and thread pitch: 0.001 - 2,000 mm/rev Feed range longitudinal and thread pitch, optional up to: 13,000 mm/rev Feed force flat: 9,000 N Feed force longitudinal: 12,000 N Automatic tool turret Number of tool stations: 12 With tool drive for 6 stations Tool holder system (DIN69880) VDI40 Equipment SIMENS SINUMERIK 840D sl (Shop Turn with manual functions) COMBI control station C-axis with drilling, milling, and engraving cycles Residual material detection and machining – during roughing and contour pockets MULTIFIX C forne setup Three-jaw chuck SMW AUTOBLOK: HI-GRIP HGF260-81-3 Oil emulsion mist filter for work area extraction: MAHLE LTA600 4 driven axial tool holders 2 driven radial tool holders

Condition: used, Year of construction: 2005, operating hours: 11,148 h, total height: 3,000 mm, total length: 5,000 mm, total width: 2,500 mm, Empty weight: 10.500 kg Price: On request - Year: 2005 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 11161 - Operating hours: 11148 - Drive system: CNC - Horizontal/vertical: vertical - Control system brand: Siemens - Power [kW]: 20.0 - Number of axes [pcs]: 3 - X-axis travel [mm]: 2000 - Y-axis travel [mm]: 620 - Z-axis travel [mm]: 520 - Table length [mm]: 2500 - Table width [mm]: 600 - Tool holder: SK40 - Main spindle power [kW]: 20 Chjdpfx Asx Dkgaeb Tjf - Max. spindle speed [rpm]: 12000 - Options: Tool magazine, Chip conveyor, External cooling - └ Tool magazine [pcs.]: 30 - Transport dimensions: 5000mm x 2500mm x 3000mm (l x w x h) - Transport weight [kg]: 10500kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: excellent (used), CATALOGUE NUMBER 7026 TECHNICAL DATA - Infeed width: 740mm - Infeed height: 300mm - Shaft width: 780mm - Shaft diameter: 1000mm - Knife length: 780mm - Number of knives: 2 pcs - Screen dimensions: 55x55mm - Bottom: 4 toothed feed rollers - Lower shaft motor: 5.5kW - Top: 3 toothed feed rollers - Upper shaft motor: 5.5kW - Belt conveyor feeder - Length of belt feeder: 4300mm - Width of belt feeder: 600mm - Feeder belt drive motor: 2.2kW - Main motor: 90kW - Reverse - Autoreverse - Overall machine dimensions (L/W/H): 4600x2350x1700mm - Overall feeder dimensions (L/W/H): 4550x980x970mm - Total weight: approx. 11,000kg – German-made – Autoreverse (adjustable) – Used shredder, in very good condition Net price: 265,900 PLN Chjdpfx Abema Hv De Tsf Net price: 63,300 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR (In case of major currency fluctuations, the price may change)

Condition: used, Year of construction: 2017, operating hours: 2,110 h, lifting height: 200 mm, fuel type: electric, fork length: 1,150 mm, total height: 1,350 mm, total length: 1,800 mm, total width: 700 mm, color: other, Empty weight: 337 kg Lifting capacity: 1.400 kg - Year: 2017 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: F20164H00171 - Operating hours: 2110 - Type: Elektrische palletwagen - Lifting capacity: 1400kg - Lifting height: 200mm - Fork length: 1150mm - Fork width: 560mm - Drive: Electric - Battery voltage: 24V - Transport dimensions: 1800mm x 700mm x 1350mm (l x w x h) - Transport weight [kg]: 337kg - Transport packages [pcs.]: 1 Chodpfxoxfvcce Ab Tjf Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Tess van den Boom

Condition: excellent (used), Catalogue number: 7715 TECHNICAL SPECIFICATIONS - Maximum workpiece width: 220 mm - Maximum workpiece height: 130 mm - 8 spindles: 1) Bottom horizontal 220 mm 5.5 kW 2) Right vertical 130 mm 7.5 kW 3) Left vertical 130 mm 7.5 kW 4) Right vertical 130 mm 5.5 kW 5) Top horizontal 220 mm 11 kW – 5th spindle electrically adjustable up/down 6) Bottom horizontal 220 mm 5.5 kW 7) Bottom horizontal 220 mm 5.5 kW – 7th spindle with support + Jointer system (cutterhead sharpening) 8) Universal 220 mm, 360° adjustable, 7.5 kW - All spindles adjustable vertically and laterally - Spindle diameter: 40 mm Feed system (top): Codpfx Asw Ipcveb Tshf - 6 double-toothed infeed rollers, driven, + 1 single roller - 3 double smooth rubber outfeed rollers, driven + 3 single rollers - Digital length counter Feed system (bottom): - Swivelling toothed steel infeed roller integrated into lower table - 3 smooth steel feed rollers - Feed drive via Cardan rollers - Pneumatic pressure rollers - Stepless feed speed adjustment + 2-speed gearbox: 10–60 m/min - Feed motor: 10 kW - Electric thickness adjustment - Body lifting motor: 0.75 kW - Centralised table lubrication - Extraction connection diameters: 5x140 mm, 3x120 mm - Machine dimensions (LxWxH): 4680x1780x1850 mm - Control cabinet dimensions (on pallet): 1020x1000x2230 mm - Weight: approx. 5000 kg ADVANTAGES - Equipped with 8 cutterheads - Universal spindle - Ideal for wet and dry timber - Made in Germany, WEINIG brand - Unpainted (original finish) - Very low operating hours - Used thickness planer, like new Net price: 165,900 PLN Net price: 39,500 EUR (based on exchange rate 4.2 EUR) (Prices may change with significant exchange rate fluctuations)

Condition: excellent (used), CATALOG NUMBER 7661 TECHNICAL DATA - max machining diameter range: 140 mm - min input material length: 900 mm - machining allowance (on diameter): max 30 mm - cutter head drive motor: 15 kW - stepless feed speed adjustment via inverter - feed motor approx. 2.2 kW - pneumatic cylinders: 2 pcs - knife setting tool included - additional bushings in the set: 80, 100, 130 mm - mounted bushing diameter: 70 mm In order: - infeed chute - 4 gear-driven feed rollers (first two pneumatically adjustable) - 3-knife cutter head - 3 smooth outfeed feed rollers - dimensions (LxWxH): 4500x850x1800 mm - weight approx. 3000 kg Chsdpfjwnnkmox Ab Tof ADVANTAGES – 2 pneumatic cylinders – knife setting tool – additional bushings included – used rounder/turning machine – very good condition Net price: 43,900 PLN Net price: 10,450 EUR based on a 4.2 exchange rate (Prices may change with significant rate fluctuations)