Used Cross Table for sale (20,450)

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Fgedpfx Alozp H R Eebsg Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: new, GRAULE ZS 170 N cross-cut and mitre saw - tiltable - Includes: - GRAULE ZS 170 N cross-cut and mitre saw - tiltable - - without machine stand and saw blade - Including: - GRAULE machine stand for type ZS 135 N and ZS 170 N Includes: - GRAULE type RO feed roller conveyor complete with support feet and connection bracket Plastic rollers with ball bearings Ø 40 mm, Roller width 300 mm, roller spacing approx. 300 mm, Support feet for roller conveyor height 885 +/- 10 mm Includes: - GRAULE type RLK roller conveyor/length stop Fgjdpfx Aeu R Sypelbsg with scale and material stop that can be folded back. Ball bearing mounted plastic rollers Ø 40 mm, Roller width 300 mm, roller spacing approx. 300 mm, Support feet for roller conveyor height 885 +/- 10 mm - new exhibition machine -

Condition: used, Year of construction: 2000, with automatic stop The stop slides the material to be cut to the cutting position according to the entered measurement Saw blade: rising from below Maximum saw blade diameter (mm): 300 right long table: with automatically adjustable stop Table length (mm): 3200 Table width (mm): 120 Fgsdpsx Srrvofx Albsg Roller conveyor left: roller conveyor length – 3550 mm, roller conveyor width – 310 mm Roller width (mm): 240 Roller conveyor and stop table: not separable Machine weight (kg): 80 without extraction system as shown

Condition: used, Roller support for saw, composed of: 2 supports: L 3000 mm x Max width 550 mm x Mini height 800 mm - Max height 950 mm 1 support fitted on machine side (see photo): L 3000 mm x Max width 550 mm x Mini height 800 mm - Max height 950 mm Fgjdpfxjzzv Rfj Albsg Rolls width: 450 mm

Condition: ready for operation (used), functionality: fully functional, spindle speed (max.): 510 rpm, table length: 457 mm, table width: 457 mm, overall weight: 1,200 kg, Kearns ‘S’ Type Horizontal Borer Fsdpfxszv T Dle Albogg Table Size 457 x 457mm Long Travel: 610mm Cross Travel: 305mm Vertical Travel: 286mm Facing Head Diameter: 250mm Spindle Speeds (6 off): 45 - 510 RPM

Condition: like new (used), Year of construction: 2022, functionality: fully functional, type of input current: three-phase, cutting height (max.): 100 mm, cutting width (max.): 1,140 mm, saw blade diameter: 300 mm, tilt adjustment saw blade: 45 °, height adjustment type: mechanical, saw blade bore: 30 mm, actuation type: electric, rotational speed (max.): 7,000 rpm, total length: 1,700 mm, total width: 1,130 mm, total height: 1,100 mm, overall weight: 400 kg, Equipment: CE marking, documentation/manual, saw blade guard, Professional panel saw SICAR SEGA 300, manufactured in 2022. The machine is equipped with a 1600 mm long aluminum panel carriage, a scoring saw, and a tilting saw unit. The robust construction, based on a cast iron table and a heavy-duty saw unit, ensures stable operation and high cutting precision. The saw is designed for processing solid wood, furniture boards, MDF, plywood, and other wood-based materials. TECHNICAL DATA: - Manufacturer: SICAR / MA.CO.2L - Model: SEGA 300 - Year of manufacture: 2022 Fgodpfezxw N Rex Albeg - Panel carriage length: 1600 mm - Carriage dimensions: 1600 × 315 mm - Main saw blade diameter: 300 mm - Main saw blade arbor diameter: 30 mm - Scoring saw diameter: 90 mm - Scoring saw arbor diameter: 22 mm - Main saw blade speed: 4500 rpm - Scoring saw speed: 7000 rpm - Maximum cutting height at 90°: 100 mm - Maximum cutting height at 45°: 75 mm - Saw unit tilting range: 0–45° - Maximum cutting width with parallel guide: 1140 mm - Main work table dimensions: 800 × 500 mm - Auxiliary table dimensions: 800 × 860 mm - Auxiliary side table dimensions: 400 × 500 mm - Main motor power: 4.0 kW / approx. 5.5 HP - Power supply: 380 V, 3 phases - Frequency: 50 Hz - Machine weight: 380 kg - CE marking EQUIPMENT: - aluminum panel carriage running on ball bearings - scoring saw unit with belt drive - manual lifting and tilting of the saw using knobs - parallel guide on a steel shaft - cast iron guide bracket with micrometer adjustment - extendable crossbeam - cross guide with two reversible stops - saw blade guard with extraction port - emergency stop switch - complete set of auxiliary tables as shown in the pictures The machine is in very good visual condition. Compact and robust panel saw suitable for both a carpentry workshop and the production of custom-made furniture. The machine is available immediately. It is possible to start and inspect it before purchase. We offer assistance with loading and the possibility of arranging transport throughout Poland and abroad. JBS WOODWORKING MACHINERY Sale of used and new woodworking machines. It is possible to view the machine in operation by prior appointment. It is possible to test the machine on site. Financing options are available through leasing or installment plans. WE ORGANIZE TRANSPORT WHERE CAN YOU SEE OUR MACHINES? JBS WOODWORKING MACHINERY WOLICA DRUGA 26 23-310 MODLIBORZYCE jbsmaszyny.pl

Condition: excellent (used), Year of construction: 2020, - total length: 8,1 m - total width: 1200 mm - height: 950 mm Hydraulic lift, lifting capacity around 1 ton. Fgedpfx Aetddw Aslbjg

Condition: new, Year of construction: 2025, Martin panel saw T 66 Fsdpfx Alov Erkajbogg Cutting height: 155 mm Saw blade diameter: 450 mm Swivelling: one-sided Drive power: 5.5 KW Edging table length: 3.0 m Cutting width: 1350 mm Parallel stop via handwheel Standard cross table for length stop for angle cuts Length stop analogue with continuous system Table extension at the rear T66 T6615/2-a Drive power 5.5 KW T6630/3-a Edge table length 3.0 m T 6635/3-a Cutting width 1350 mm T 6641-a Parallel stop moved via handwheel T6660/1-a Standard cross table for angle cuts T 6670-a Length stop analogue T 6680/1-a Table extension at the rear Location: from stock 54634 Bitburg - available immediately - Some of the pictures show options that are not included in the offer.

Condition: excellent (used), Panel Beam Saw - With rear lifting table Numerical Control POWER CONTROL V2.1 (Power TOUCH) Software CADmatic 5 Cross-chains for transporting panel packs in the lifting table Lifting scissor table (mm) 4300 x 1600 Fgodpfxezxn Ecs Albog Rear pushers (N.) 1 with clamps / grippers 12 Turning device (rotating unit) at 90° Max. cutting width (mm) 4300 - Useful stroke of the pushing system (mm) 4300 Max blade projection (mm) 125 Scoring Unit (max saw diameter / power) mm 180 / Kw 2,2 Main Sawing Unit (max saw diameter / power) mm 450 / Kw 28 Adjustable speed of the saw carriage (m/min) 1 - 150 Front supporting tables with Air blowing system (N.) 4 (3 x 2160mm x 650mm + 1 x 2160mm x 800mm) Total power (Kw) OPTIONAL: 200062) Automatic unloading system for cut panels and stacking system AUTOMATECH ROBOTECH with Robot KUKA Mod. KR 470-2 PA

Condition: like new (used), Year of construction: 2019, Altendorf F45 EvoDrive panel saw in like-new and fully functional condition, manufactured in 2019. The saw has only 9 operating hours!!! Saw blade swivel: 0° to 46° Fodpozzrwujfx Albjgg Max. saw blade diameter: 450 mm Max. cutting height: 150 mm (vertical) / 103 mm (at 45° tilt) Power (main motor): 5.5 kW Parallel fence: 1,000 mm Angle/cross fence: extendable up to 3,200 mm Dust extraction connections: Ø 80 mm on the guard (top), Ø 120 mm on the port (bottom) Machine weight: approx. 1,200 kg Optionally, a suitable dust extraction system from Höcker Polytechnik / Nestro can also be purchased (see last picture). The machine can, of course, be inspected and thoroughly tested while powered on. The sale is to commercial businesses and excludes any liability for material defects. No guarantee, warranty, or right of return.

Condition: excellent (used), Year of construction: 2002, functionality: fully functional, power: 5.5 kW (7.48 HP), cutting height (max.): 140 mm, cutting width (max.): 1,400 mm, saw blade diameter: 420 mm, tilt adjustment saw blade: 45 °, saw blade bore: 30 mm, actuation type: hydraulic, Equipment: CE marking, documentation/manual, saw blade guard, scorer, Panel saw ALTENDORF, F45, with scoring unit, tilting and height adjustment of the saw blade electrically controlled up to 45 degrees, sliding table 3000mm. Fodpfxezzy Sae Albogg

Condition: excellent (used), Year of construction: 2010, Panel saw Manufacturer: Felder Type: Kappa 550 Fgodpezy Uzyjfx Albog Year of manufacture: 2010 Sliding table length: 3,200 mm Cutting width: 1,250 mm Cutting height: max. approx. 204 mm Power: 7.5 kW Max. saw blade diameter: 550 mm Height adjustment: Electric Angle adjustment: Electric Cutting width display: Digital Scoring saw: No Motor brake: Yes

Condition: used, Year of construction: 1972, spindle diameter 100 mm x-travel 1400 mm dismantled ja Fgjdpfx Ajzycrgolbog tool adaptor SK 50 digital ja weight of the machine ca. 14 t

Condition: good (used), Manufacturer: WMW Fgjdpfxouan Rmo Albsg Machine type: FUW 200/1 WMW Auerbach Machine number: Type / Model: Turn-tilt-swivel table Table top: 540 x 245 mm Clamping surface: 460 x 175 mm Stop surface: 290 x 195 mm Slot width: mm Groove spacing: mm Table cross adjustment: 135 mm Equipment: rotatable, tiltable and swiveling Condition: good Weight: 80 kg Dimensions: 550 x 500 x 300 mm

Condition: ready for operation (used), Year of construction: 2012, operating hours: 926 h, functionality: fully functional, machine/vehicle number: 546324, saw blade diameter: 500 mm, cutting width (max.): 300 mm, overall weight: 1,500 kg, saw blade length: 7,209 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Max. saw blade length: 7,209 mm Max. saw width: 300 mm Max. saw blade diameter: 500 mm Arbor saw blade diameter: 85 mm Infeed table length: 7,850 mm Outfeed table length: 2,400 mm MACHINE DETAILS Voltage: 400 V Current consumption: 22 A Fuse: 25 A Main motor power: 7.5 kW Connected power: 11 kW Fodezzbfbspfx Albegg Dimensions & Weight Dimensions (L x W x H): 11,250 x 900 x 1,800 mm Weight: 1,500 kg Operating hours: 926 h EQUIPMENT CE marking

Condition: used, table length 750 mm Fsdpszzrbmsfx Albegg table width 425 mm table surface area 600 x 320 mm x-travel 400 mm y-travel 280 mm - 2 pieces on stock -

Condition: used, Year of construction: 2008, functionality: fully functional, machine/vehicle number: LW 08.0169, Used Ruff LW-90 table winding machine with tailstock. Fjdpfozzpqfox Albjgg Self-collection only – location: 4120 Neufelden, Austria.

Condition: good (used), Year of construction: 1986, functionality: fully functional, Equipment: saw blade guard, scorer, The panel saw comes with approximately 10 saw blades and scoring saws, as well as a laser. Fjdpfx Aloy Suidebjgg

Condition: used, functionality: fully functional, power: 7.5 kW (10.20 HP), input voltage: 400 V, cutting height (max.): 125 mm, saw blade diameter: 400 mm, tilt adjustment saw blade: 45 °, height adjustment type: mechanical, saw blade bore: 30 mm, actuation type: mechanical, rotational speed (max.): 6,000 rpm, total length: 3,200 mm, Equipment: documentation/manual, scorer, Welcome, we are selling a Robland Z320 panel saw. Motor: 7.5 kW / 400 V Saw head can be swiveled up to 45° Saw blade diameter: 400 mm Sliding table length: 3,200 mm Dust extraction port: 120 mm Max. cutting height: 125 mm Max. cutting height at 45°: 100 mm Speeds: 4,000/5,000/6,000 rpm Scoring saw blade diameter: 100 mm Scoring saw cutting height: 0 - 4.5 mm Scoring saw tilt: 0 - 45° Scoring saw speed: 7,000 rpm with scoring saw with table extension with table widening with edge guide with miter gauge Fsdpfxszylxpj Albjgg with additional workpiece support with standard tools for saw blade replacement with operating manual in German without upper dust extraction/hood Location: 49176 Hilter a.T.W., unpacked Handover in the current condition as inspected, without warranty or guarantee.

Condition: used, Year of construction: 2015, total length: 2,100 mm, total width: 900 mm, total height: 1,050 mm, Colour: White Weight: 250 kg - Details: Fsdpfszrkxrex Albsgg - └ Description: Front-wheel drive not available - Year: 2015 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: KK/126675 - Main motor power [kW]: 3.0 - Max. cutting height [mm]: 100 - Parallel stop displacement [mm]: 1300 - Roller table length [mm]: 840 - Table width [mm]: 560 - Min. saw blade diameter [mm]: 250 - Max. saw blade diameter [mm]: 315 - Arbor saw blade diameter [mm]: 30 - Dust extraction nozzle diameter [mm]: 120 - Schuinstelbare zaagaggregaat: - └ Min. tilt adjustable [°]: 45 - └ Max. adjustable [°]: 90 - └ Cutting height at 45° [mm]: 70 - Voltage [V]: 400 - Current consumption [A]: 10 - Fuse [A]: 16 - Power [kW]: 3.0 - Transport dimensions: 2100mm x 900mm x 1050mm (l x w x h) - Transport weight [kg]: 250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: good (used), Year of construction: 2018, functionality: fully functional, Equipment: CE marking, scorer, Horizontal panel dividing saw / Horizontal panel saw with lifting table feed Manufacturer: SCM / Gabbiani Type: Gabbiani ST 115 Year of manufacture: 2018 Horizontal beam saw with lifting table feed from the rear, originating from a parquet factory. Fgsdpszyx Evofx Albog Cutting length approx. 3200 mm Cutting depth on the lifting table approx. 1850 mm Max. stack height on the lifting table (with supports) approx. 600 mm Saw blade projection 115 mm Variable saw carriage speed 0 - 135 m/min. Variable sliding table speed 0 - 70 m/min. Motor of the main saw blade approx. 9 kW Main saw blade speed 3900 rpm Saw blade diameter 400 mm Motor of the scoring saw approx. 1.8 kW Scoring saw speed 6300 rpm Scoring saw blade diameter 160 mm 6 clamping devices (3 of which with front aligner) 2 air cushion tables, each with blower Voltage: 400 V, 3 phases, 50 Hz, 43 A Weight approx. 5500 kg Data partially estimated and taken from the brochure.

Condition: used, Martin t60 panel saw carriage: 330 cm, tilt: 0-45 degrees, and motorized adjustment of the blade height, sliding table on the right side, manually adjustable up to 1250 mm with an electronic display, 3-axis scoring saw, electrically adjustable, scoring saw that extends and retracts pneumatically, main motor: 5.5 kW, Fsdpozzdi Nofx Albogg 3 cutting speeds, max. blade diameter: 400 mm.

Condition: used, Year of construction: 1973, spindle diameter 140 mm x-travel 2000 mm y-travel 2000 mm Fsdjy Umc Uepfx Albsgg z-axis 1500 mm spindle stroke - max. 800 mm spindle taper ISO 50 table surface area 1800 x 1500 mm table load 15000 kg turning speed range 2,3 - 810 U/min total power requirement ca. 30 kW weight of the machine ca. 31000 kg dimensions of the machine ca. 7300 x 5600 x 4000 mm Equipment: - Faceplate with NC facing slide and NC rotary table - Heidenhain digital readout - Various tool holders - Various clamping devices

Condition: good (used), Year of construction: 2003, Equipment: scorer, Altendorf F45 Fgjdpfszzl Dzox Albeg Length of aluminum sliding table: 3,400 mm Saw blade diameter: 315 mm Main saw motor: 4 kW Scoring saw motor: 0.75 kW Saw blade width to the right of the saw: 1,350 mm Saw blade height adjustment: automatic positioning Saw blade tilt: automatic positioning

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, machine/vehicle number: 1600058, total height: 300 mm, total width: 670 mm, total length: 890 mm, rotary table diameter: 600 mm, table diameter: 600 mm, compressed air connection: 8 bar, Haas HRT600 CNC rotary table / 4th axis / Ø 600 mm Haas HRT600 CNC rotary table (4th axis) for sale. This rotary table comes from a Haas VF-6B/40HE and was used as a 4th axis. The table is equipped with a servo drive and was tested on the machine again before removal. The axis could be moved and rotated flawlessly via the control. The rotary table has a diameter of approximately 600 mm. Serial number of the rotary table: 1600058. Condition Rotary table rotates and moves via the Haas control. Functionality tested before removal. No detailed geometric measurement performed. Angular accuracy, runout, and repeatability were not checked with a dial indicator. Sale due to non-use. Fgjdozzbitepfx Albeg Technical data Manufacturer: Haas Automation Model: HRT600 Type: CNC rotary table / 4th axis Table diameter: 600 mm Serial number: 1600058 Year of manufacture probably 2004/2005 (matching the original machine)