Used Bubble Wrap for sale (859)

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: Fsdpfezp H R Ejx Ak Uepl The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: used, Year of construction: 2010, functionality: fully functional, machine/vehicle number: CON.07.10.0154, compressed air connection: 8 bar, input voltage: 230 V, total width: 1,329 mm, total length: 1,150 mm, total height: 1,725 mm, overall weight: 812 kg, pneumatic connection: 8 bar, Equipment: documentation/manual, 6-color pad printing machine from the manufacturer TAMPOPRINT, model Concentra 60-6 Max. printing area diameter (circle diameter) 55mm, total of 6 colors Year of manufacture 2010, weight 812 kg Air consumption 48 standard liters per cycle Good overall condition, machine fully functional, minimal air loss on one of the main valves. Visual condition as shown in the current photos. Scope of supply: TAMPOPRINT Concentra 60-6 as a stand model + Foot pedal + Hand crank for height adjustment of the tilting table + 6 used ink pots 60mm + 6 used printing rings (for the ink pots) + 2 used mounting tables (for ink pot and cliché mounting) + 2 used gripper tongs (for ink pot and cliché mounting) + 2 used pad coupling devices plus mounting screws (4 pad coupling devices still need to be purchased) + 1 heavy-duty hook for transporting the machine + Documentation (operating manual, parts list, wiring diagram) Option 1 6 additional used ink pots 60mm, EUR 420,- excl. VAT. Option 2 4 pad coupling devices (new) from the manufacturer, EUR 1,098,- Packaging: The machine can only be packaged by wrapping it completely in cardboard and bubble wrap; it will not be placed on a pallet. The pad printing machine can be inspected and tested in Pottendorf by appointment. Delivery: Ex works Pottendorf (Austria). For collection, only trucks with a tail lift are permitted; please note the machine's weight. The transport of this machine is at the buyer's expense and risk. Packaging costs EUR 120,- Selling price EUR 18,200,- excl. VAT. Fpsdpfszwv Rwsx Ak Ujl New price approx. EUR 70,000,-

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Equipment: documentation/manual, type plate available, Taylor Hobson Talyrond 265 roundness measuring instrument. Extremely accurate; it can measure the roundness of lenses, optics, pistons, turbine components, tubes, shafts, and also eccentricity, e.g., of cams on a camshaft or journals of a crankshaft. It is certainly of interest for motorsport and tuning companies. The first photo is a "representative image" from a Taylor Hobson catalog, showing how it is constructed, except for the computer, which is a newer, more modern HP model with a small form factor. Max. diameter 350 mm Max. test piece height 500 mm (higher values are possible by measuring in two parts, up to a maximum of 1000 mm...) Fpodpfszcqy Eex Ak Ujl Self-centering of the workpiece +/- 5 mm Max. weight of test piece 40 kg The system has been used very little and has had only two owners. The first owner, from whom I bought it, was an implant company in Hamburg; it was used in a "medically clean environment" and is extremely clean. It was never located in a dirty machine hall. The year of manufacture is estimated to be between 2003 and 2005. The Taylor-Hobson measurement software is, of course, included and runs on the supplied HP computer (without a password...). It is also on the USB stick, perhaps for installation on another machine at your location. Accessories are included: the original Taylor-Hobson desk, computer, monitor, seven (7!) measuring probes, each of which is very expensive to purchase. A sample/sample lens (hemisphere) is included for calibration! The very detailed operating manual is on the USB stick, and all circuit diagrams and functional diagrams are also included! The system will be shipped on two Euro pallets via a freight carrier. It is already well secured on them. The Talyrond 265 and the desk will be wrapped with bubble wrap, etc., and secured with stretch film to provide extreme protection during transport. The system itself is fixed with "transport safety screws." Shipping is at the buyer's expense and will be on two Euro pallets. The measuring system should definitely be assembled and put into operation by a Taylor Hobson service technician, who can then also recalibrate the system on-site. This is now recommended after a few years. Errors can be made during assembly and commissioning. For example, some locking screws are installed for transport, and if you forget them, the system could be damaged when starting up. A truly well-maintained, very accurate system that will continue to provide excellent service for many years to come!

Condition: like new (used), Year of construction: 2009, functionality: fully functional, This automatic wrapping machine is specifically designed for use with dry ice slices and/or blocks. All parts in contact with the product are made of stainless steel. Automatic pitch adjustment on the conveyor, and all motors are torque-controlled. The welding temperature is displayed and electronically controlled. The control panel consists of various instruments and visual alarms and is equipped with a self-diagnostic device. TECHNICAL DATA Working speed: Up to 25 wraps per minute, 25 meters of film per minute. Product size: Max wrap width: 250mm, Max wrap height: 60mm, Wrap length: 40 to 260mm, 140 to 580mm, and 200 to 800mm. Compressed air: 4 to 5 bars Fodpfx Akjzxgglo Ujpl Version: standard version is right-hand operated.

Condition: used, Year of construction: 2002, functionality: fully functional, machine/vehicle number: 10647A, automatic overwrapping machine, primarily used in the pharmaceutical and cosmetics industries for the precise wrapping of individual cartons or bundled packages with film Format min / max Length (A) approx. 50 mm approx. 250 mm Width (B) approx. 20 mm approx. 180 mm Height (C) approx. 15 mm approx. 100 mm Operating voltage 400 V / 50 Hz (3-phase) Fedpozz Hxtsfx Ak Uepl Control system: Pester Pac (Lauer)

Condition: new, Year of construction: 2010, connected load frequency 230 V Fodpsx Dnftofx Ak Ujpl dimensions 1,6 x 0,8 x 1,55 mm Bubble wrap machine - Documentation - Includes 7 rolls of film - Like new condition See pictures

Condition: excellent (used), Year of construction: 2017, operating hours: 8,060 h, functionality: fully functional, total length: 3,051 mm, total height: 1,548 mm, total width: 1,635 mm, type of input current: three-phase, product height (max.): 120 mm, product height (min.): 20 mm, product length (min.): 100 mm, product length (max.): 550 mm, product width (max.): 380 mm, product width (min.): 30 mm, input voltage: 400 V, compressed air connection: 6 bar, input current: 22 A, width of welding knife: 450 mm, length of welding knife: 580 mm, overall weight: 1,000 kg, power: 12.9 kW (17.54 HP), input frequency: 50 Hz, air demand: 13.8 m³/h, We are offering this very well-maintained Robopac COMBITECH 5845 AVH shrink wrapping machine and shrink tunnel, manufactured in 2017. Model: COMBITECH 5845 AVH Serial number: 30153878 Year of manufacture: 2017 Mileage: 8060 Sealing bar dimensions WxH: 580 mm x 450 mm Supply voltage: 400 V Product dimensions min. WxDxH: 100 mm x 30 mm x 20 mm Product dimensions max. WxDxH: 550 mm x 380 mm x 120 mm Conveyor belt speed: 5 - 40 m/min Fedjztwg Eopfx Ak Uepl Film thickness: Polyolefin 9 - 35 µm, Polyethylene 25 - 50 µm Frequency: 50/60 Hz Number of phases: 3 Current consumption: 22.0 A Total power: 12.9 kW Air consumption: 230.0 Nl/min Maximum pressure: 6.0 bar Weight: 1,000.0 kg If you have any questions or require further information, please do not hesitate to send us a message or call us.

Year of construction: 2014, condition: good (used), High-quality Airpad machine from a renowned manufacturer. Suitable for producing custom-designed, air-filled protective and cushioning elements made of PA and PE film, as well as paper-based bubble wrap. Typically, four air cushions are produced per working cycle. Various formats can be produced. For this purpose, 10 programs are available to store multiple parameters. By calling up the corresponding program on the display, air cushions can be produced with lengths ranging from 4 cm to 16 cm and individually defined fill levels. The resulting air cushion strips are then wound into rolls by a motorized device. When the roll is full, the machine automatically shuts down. The finished roll can then be manually removed and used as packaging material. The machine can be moved by pushing it on its rollers and secured in place using brakes. Fodpokkcqqjfx Ak Uopl The machine can be demonstrated while powered on.

Condition: used, Year of construction: 2000, A machine for packaging containers such as bottles (beer, wine, beverages, oils) or cans into cardboard collective packaging. The containers are grouped and then wrapped with a cardboard blank and glued together to form a collective package. Manufacturer: SOTEMAPACK Model: WRAP-AROUND Fjdpfx Akjywclwj Uspl Year of manufacture: 2000 Capacity: up to 720 packages/hour (12 packages/minute) Control system: S7-300 Original technical documentation included. Technical condition: used machine, in working order at the time of disconnection, condition as shown in the pictures.

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, overall weight: 6,600 kg, year of last overhaul: 2025, Overhaul work 2025 - Lifting devices overhauled - Bottle carousel overhauled Fpjdpfx Akezv Rp Se Uol - Glue roller overhauled - Roller motor replaced - New protective covers installed - Printing heads overhauled - All sensors of the glue heating system replaced - Hoses of the extraction unit replaced - Entire electrical system inspected TECHNICAL DETAILS Output: 45,000 bottles/hour Bottle format: 500 ml, 1 l, 1.5 l Labeling system Labeling method: Roll-fed / roll labeling Label placement: Wrap-around labeling Rotation direction: Clockwise Carousel movement: Mechanical cam drive with brake/clutch Optical centering system: Mechanical Head adjustment: Manual Number of bottle carousels: 25 Number of labeling stations: 2 MACHINE DETAILS Mains voltage: 400 V Mains frequency: 50 Hz Power consumption: 35 kW Current consumption: 57 A Machine weight: 6,600 kg EQUIPMENT - Mechanical cam drive with brake/clutch for bottle carousel movement - Mechanical optical centering system - Manual head adjustment - Roll-fed labeling system for wrap-around labels - Two labeling stations - Safety guards

Condition: used, Year of construction: 2012, functionality: fully functional, total width: 1,370 mm, total length: 2,950 mm, total height: 1,800 mm, We offer this used Profi Packer SCV 400 film wrapping machine, manufactured in 2012. Manufacturer: Profi Packer Model: SCV 400 Year of manufacture: 2012 Condition: used Category ID: 1262 Fodozvdadspfx Ak Uspl Type ID: 907 Machine type: Film wrapping machine Machine dimensions (L x W x H): 2,950 x 1,370 x 1,800 mm Cycle rate per minute: approx. 65 cycles Film thickness: 7 to 80 μm Includes infeed conveyor and hot air tunnel for heat sealing. If you have any questions or require further information, please feel free to send us a message or call us.

Condition: excellent (used), Year of construction: 2017, operating hours: 627 h, functionality: fully functional, total length: 6,900 mm, total height: 1,800 mm, total width: 1,600 mm, type of input current: three-phase, input voltage: 400 V, input current: 62 A, passage height: 300 mm, overall weight: 1,200 kg, passage width: 800 mm, input frequency: 50 Hz, nominal power (apparent): 43 kVA, throughput speed: 20 mm/s, temperature: 250 °C, Equipment: documentation/manual, BVM SC 8530 D3 Shrink Tunnel – Year of Manufacture 2017 – approx. 627 operating hours Fpodpfezwk T Tex Ak Usl For sale is a BVM shrink tunnel SC 8530 D3, year of manufacture 2017, in technically flawless and visually very good, well-maintained condition. The system has only approximately 627 operating hours and is suitable for shrinking packaging films using hot air circulation. The adjustable tunnel transport and the adjustable side and bottom air flow allow the shrinking result to be adapted to different products and films. Technical data Manufacturer: BVM Brunner GmbH & Co. KG Type: SC 8530 D3 Year of manufacture: 2017 Machine no.: 20170962241 Commission no.: 6224 Operating hours: approx. 627 h Mains voltage: 3N 400 V Mains frequency: 50 Hz Current consumption: 62 A Power: 43 kVA Fuse rating: 63 A Max. passage width: 800 mm Max. passage height: 300 mm Transport speed: approx. 1.2 m/min at 50 Hz Working temperature: 110–250 °C Suitable for film types up to 100 µm External dimensions L × W × H: approx. 6,900 × 1,600 × 1,800 mm Total weight in operating condition: approx. 1,200 kg Sound emission: ≤ 75 dB(A) Equipment / Functions Hot air circulation Adjustable tunnel transport Temperature control Adjustable side air flaps Adjustable bottom air flow Heating fan Cooling fan Electronic preset counter Emergency stop device Cooling automatic Clean and clearly structured control cabinet Original operating manual available Condition The system is in perfect technical condition and is also visually in very good and well-maintained condition. With only approximately 627 operating hours, the machine has very low operating hours. Price €17,000 (negotiable) Inspection possible by arrangement. Further information and pictures available upon request. Subject to prior sale and errors.

Condition: like new (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: 1393, arm reach: 2,500 mm, No minimum price – guaranteed sale to the highest bidder! Fedpfx Aszrd R Usk Uopl Includes notebook and PCdemis 2016 software! TECHNICAL DETAILS FP2 Mobility Pack: included Measuring software: PCdemis (2016) Notebook: DELL M 6800 with a 17-inch screen and Windows 10 Tripod: Brunson heavy-duty rolling tripod, type 230 FIX Measuring range: 2,500 mm Accuracy class: 5 Number of axes: 6 Target single-point deviation: 0.020 mm Target volumetric accuracy: ±0.029 mm Arm weight: 8 kg Probe set: Probe with ruby ball 3mm, 6mm and with steel ball 15mm EQUIPMENT - Carbon fiber double-tube construction enables separation of stability and measurement - AbsoluteArm series can start measuring directly without referencing - Probing system with automatic probe recognition - Mounting plate with magnet - FP2 Mobility Pack - Transport case - Magnetic tripod - Test bar L = 700 mm - Test sphere D = 25 mm - Power supply with connecting cable - USB cable measuring arm - notebook - Dust cover - New pressure cylinder installed - Relabeling of the measuring arm before calibration 2023 - ISO 10360 acceptance with certificate 2023 is included Shipping conditions - Ex works, without additional packaging (measuring arm in case and notebook in protective cover) and Brunson rolling tripod – i.e. 3 parts - If the buyer arranges collection via a shipping company, the seller recommends special packaging (approx. 160 x 70 x 70 cm cardboard box on a pallet, with bubble wrap inside) and a Euro pallet (Brunson rolling tripod) at a price of €250, secured with strapping to the pallet.

Condition: good (used), Year of construction: 1992, functionality: fully functional, product height (max.): 200 mm, product width (max.): 600 mm, nominal power: 12.75 kW (17.34 HP), Shrink-wrapping machine with infeed conveyor table, in good and functional condition. Maximum product width: 600 mm. Fpodpozb Duysfx Ak Uol

Condition: used, Year of construction: 2015, Overview This Atlanta Giotto is a single-lane wrap-around case packer for end-of-line carton packaging of PET bottles, rated at more than 20 cartons per minute. It erects the wrap-around case around the bottle group from a flat blank held in an inclined magazine, and closes it with a hot-melt glue unit. Neutral and printed carton both run on the machine. The machine was built in 2015 and ran on a mineral water bottling line until early 2025, packing 1.5 l PET bottles in 4 x 3 cartons and 1.0 l PET bottles in 5 x 3 cartons. It was operated alternately with a shrink-film bundling process, so its operating hours are low. Control is a Siemens S7 PLC with a touchscreen HMI panel. Infeed and outfeed conveyors, motorisation and the CE control panel are part of the machine. Technical data - Manufacturer: Atlanta - Model: Giotto - Year of manufacture: 2015 - Machine type: single-lane wrap-around case packer - Capacity: more than 20 cartons/minute - Infeed: single lane, inclined carton magazine - Carton formats: 80 x H262 mm for 1.5 l PET bottles, 87.5 x H322 mm for 1.0 l PET bottles Fpedpfxjzxtyro Ak Usl - Pack patterns: 4 x 3 bottles in 1.5 l PET, 5 x 3 bottles in 1.0 l PET - Carton: neutral or printed - Case closing: hot-melt glue unit - Control: Siemens S7 PLC with touchscreen HMI panel - Length: approx. 7,175 mm machine body, plus 1,300 mm infeed conveyor - Width: approx. 2,345 mm - Height: approx. 2,336 mm - Infeed height: min. 1,050 mm - Weight: approx. 800 kg magazine section, approx. 2,250 kg packer body - Power supply: 25 kW - Compressed air: approx. 400 Nl/min at 6 bar - Infeed belt: acetal, 685 mm wide Equipment - Infeed and outfeed conveyors - Inclined carton magazine - Hot-melt glue unit - Motorisation and CE control panel - Siemens S7 control with touchscreen panel - Electrical and mechanical drawings - Service and maintenance manuals - Spare parts books Condition Used, in very good condition with a low number of operating hours. The machine was in production until early 2025 and has since been dismantled and moved into storage. It can be inspected dismantled in the warehouse by appointment. Availability Immediately available. Location: Italy. Lifting, craning, loading and transport are available on request and are not included.

Condition: new, Year of construction: 2025, Gutenberg FLEXOR Flexographic Printing Machine – High-Performance Printing for Packaging & Labels Upgrade your packaging production with the FLEXOR flexographic printing machine, engineered for converters and packaging manufacturers who need reliability, flexibility, and consistent high-quality print. Designed for modern production environments, FLEXOR combines robust construction with customizable configuration to support a wide range of substrates and applications. Built for Modern Packaging Production The FLEXOR is designed as a multi-application flexo press capable of producing professional packaging and labels across multiple industries. Its modular design allows you to configure the machine according to your product range and future expansion plans. Key advantages High-quality flexographic printing with excellent color consistency Wide substrate compatibility Customizable configuration and upgrade options Reliable performance for long production runs Ideal for both packaging converters and label producers Wide Range of Packaging Applications The FLEXOR press is suitable for printing on: Paper bags and shopping bags Folding cartons and corrugated packaging Flexible packaging and plastic bags Fjdpfx Akoumn Exe Uspl Food packaging and pouches Industrial and household product packaging Produce vibrant, durable prints that elevate brand visibility and shelf appeal. Ideal for Food & Beverage Packaging The FLEXOR is widely used for: Snack food bags and bakery packaging Bread, pasta, rice, flour, sugar, and salt packaging Sauce, ketchup, mustard, and honey sachets Salad dressing pouches and yogurt lids Milk cartons and juice cartons Beverage and water bottle labels Wine and specialty drink labels Designed to support food-safe packaging production with consistent print quality. Perfect for Labels & Consumer Products Expand into high-margin label production: Cosmetic and personal care labels Shampoo and beauty product packaging Pharmaceutical and medical packaging Household and detergent labels Automotive, lubricant, and paint labels The FLEXOR enables converters to serve multiple industries with one press. Additional Specialty Applications This machine is also suitable for: Agricultural and gardening packaging Bubble wrap and gift wrap Greeting cards and specialty prints Medical packaging and blister packs Industrial packaging solutions A truly versatile press designed to grow with your business. Why Choose the FLEXOR? Flexible configuration and upgrade potential Suitable for startups and expanding converters Designed for efficiency, reliability, and scalability Backed by professional installation, training, and after-sales support Boost your packaging capabilities and open new markets with the Gutenberg FLEXOR flexographic printing machine. Contact us today for specifications, configuration options, and pricing.

Condition: ready for operation (used), Year of construction: 2019, functionality: fully functional, machine/vehicle number: h288 di, power of vacuum pump: 11 W, overall weight: 4,900 kg, Resta Automatic Mattress Packaging Machine: Integrated Compression and Decompression The Resta mattress packaging machine is an automatic packaging machine designed for the industrial packaging of mattresses. In practice, on your production line, this machine performs double packaging with mattress compression followed by decompression, while also protecting it in a suitable film. Advantages of Mattress Packaging in Production and Distribution First and foremost, an efficient mattress packaging machine reduces transport volume by 70 to 80%. The mattress remains compressed during transit and then returns to its original shape upon arrival. In practice, you save storage space and reduce logistics costs. Automated Compression: Mattresses are bagged in PVC or plastic film, without manual intervention. Easy Decompression: The mattress returns to its normal shape in the store or at the customer's location. Optimized Transport: Significant reduction in volume, with more space in the truck and in storage. Presentation for Sale: Final presentation of the mattress in suitable commercial conditions. Vacuum Packaging Machine: Protection and transport of the mattress. What truly changes in production is material compatibility. The Resta mattress packaging machine adapts to different types of mattress films, including PVC film and plastic film, and ensures an airtight seal. The fully automatic packaging process avoids manual handling, limits the risk of tearing, and maintains consistent quality. Compatibility with Spring and Foam Mattresses This is particularly beneficial when your production involves both spring mattresses and foam mattresses. This packaging machine handles both types without major reconfiguration. The equipment can accommodate both bagged mattresses and compressible structures, which simplifies workshop organization. Spring Mattresses: Compression without damage to the springs, thanks to a progressive hydraulic system. Foam Mattresses: Adaptation tailored to the product, with rapid shape recovery after compression. Compatibility with PVC film and other specialized packaging films. Professional Sealing: Airtight closure of the film to protect the mattress during transport. Industrial Applications and Mattress Packaging Processes In practice, on an industrial mattress packaging line, this automatic Resta packaging machine integrates after the… Special Feature: Enables double, independent packaging (two separate bags) within the same footprint as a standard packaging machine, thanks to two superimposed polyethylene rolls. Also allows for single or customized packaging (two different rolls, automatic change according to programming). The feed conveyor and disconnectable press also allow for packaging of bed bases. Manual and/or automatic operation, interfaceable with barcodes or RFID on the production line. Official Technical Specifications: Weight: 4,900 kg Electrical consumption: 11 kW Compressed air: 6-10 bar Power supply: 400V – 50Hz three-phase Fpodpszmpvrefx Ak Usl Available Options: Press with 2 or 4 cylinders Reinforced hoist Motorized cradle for additional customization rolls Kit for disposal of polyethylene waste

Condition: used, Machine: SIGNODE Plastic band wrapper Fedpfx Aszz Rr Rsk Ujpl

Condition: used, Year of construction: 1995, Machine for palletizing cartons or bottles and wrapping with stretch film. Fodpfx Aoyrf Atjk Ujpl Manufacturer: KRONES Model: PALMASTER Year of manufacture: 1995 Set includes an OCTOPUS pallet stretch wrapper with pressing device. Used machines, still installed—as shown in the photos. Technical documentation included. A KRONES depalletizer is also available in the offer.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Brüninghaus / Fromm / Siat WS 165 NOW pallet wrapper in fully functional condition, manufactured in 2017: Turntable diameter: 165 cm Overall height: 241 cm Pallet height: 210 cm Pallet weight: 2,000 kg The access ramp can be attached at the front, left, or right. The WS 165 NOW can be programmed with 10 different programs for individual products and pallets. The machine has 5 different operating modes: Fpsdozpv Igjpfx Ak Usl - Automatic mode, upward only, as well as up and down - Automatic mode, upward only, as well as up and down with a pause for a pallet top sheet - Manual mode The motor cover (see picture) is only loosely placed and is not attached. Shipping via a freight forwarder is possible after consultation. #8553

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, product height (max.): 450 mm, product height (min.): 90 mm, product length (min.): 230 mm, product length (max.): 800 mm, product width (max.): 500 mm, product width (min.): 120 mm, Equipment: documentation/manual, The production line is a complete system suitable for packaging all types of AFH tissue paper products. The line begins with a conveyor belt which serves as a buffer. The end of the conveyor belt can be lowered, enabling the machine to handle all types of hand towels. Following the conveyor belt is an Italian-made MAC DUE stacker, which is capable of stacking toilet roll in 1, 2 or 3 layers. This is followed by another conveyor belt, which connects the stacker to the packaging machine. Next comes the CB 150A universal, fully automatic packaging machine, designed in Italy for packaging AfH tissue products. The packaging machine is highly flexible, easy to set up and operates automatically. The maximum packaging speed is 5 packs per minute. Following the packaging machine is a shrink tunnel, which is integrated into the packaging machine. Fedezvym Tjpfx Ak Uopl The MAC DUE HMI is a new DELTA model. The CB 050A packaging machine’s PLC (OMRON) comes with a new program; the electrical cabinet was rewired in 2022, and a diagram of this has also been drawn up, which I will provide with the machine. This packaging machine’s HMI is also a new Delta model. I will provide the source programs for both the HMI and the PLC with the machine. The production line was dismantled on 12 July 2026 due to the purchase of a new machine. The machine is packed and in storage, ready for delivery at any time. Commissioning can be arranged on request, but it is straightforward to install and I can also provide online support. Numerous videos have been made of the machine.

Condition: good (used), Year of construction: 1997, machine/vehicle number: 0488, KEBER Palletizer & Wrapping machine [Year : 1997 sn : 0488 Model :101 ] ~ 1700 packets / h Wrapper [Year : 1997 sn : 0487 Model :MEC ARM] Fsdpfxetgmwrj Ak Uepl Machines are operation. ALSO FOR SALE : Palletiser - ACMI - RASAR P135 H - €49,000 2000 Year ACMI s.r.l Palletiser with wrapper used for 5000ml PET bottles & EUR pallets C-1581 Serial No

Condition: used, Year of construction: 2009, machine/vehicle number: FA71, Technical Specifications & Performance DataThe SMI SK450 T is a shrink wrapping machine for PET bottles, designed for secondary packaging applications within a used bottling line. Manufactured in 2009, this second hand unit includes a heating oven for controlled shrink-film processing and bundle formation. It is configured for industrial packaging operations requiring stable, transport-ready bottle packs.Manufacturer: SMIModel: SK450 TYear of production: 2009Capacity: 45 packs/minuteContainer type: PET bottlesIncluded equipment: Heating ovenPackage configurations: 0.5L in 3x3, 0.75L in 2x3, and 1.5L in 2x3Advanced Automation & Control SystemsThis shrink wrapping machine is intended for coordinated operation in an industrial packaging environment, where bottle infeed, film handling, heat shrinking, and discharge must remain synchronized. Its operating setup supports repeatable bundle production for the stated PET bottle formats. Installation and commissioning should include verification of the existing control interface, electrical connection, conveyor synchronization, and heating-oven operating parameters.Production Line Integration CapabilitiesThe SK450 T can be positioned downstream of filling, capping, labeling, or accumulation equipment to create multipacks for distribution. In a beverage production line, shrink wrapping provides a practical secondary-packaging stage between bottle handling and palletizing. The machine is suited to PET bottle bundles in 3x3 and 2x3 arrangements, allowing the line to handle the documented 0.5L, 0.75L, and 1.5L formats.For integration into a used bottling line, upstream and downstream conveyors should be matched to the machine's infeed and discharge flow. The heating oven forms part of the packaging process and should be assessed together with film transport components, bottle guides, and pack transfer arrangements during installation planning.Machine Condition & Maintenance HistoryThe machine is in production and remains operational until 30 September 2026. It is described as being in very good condition, with regular maintenance and extensive annual overhauls carried out by the manufacturer. This maintenance history is relevant for buyers seeking second hand bottling equipment with documented attention to operational continuity and packaging performance.Operational Performance & VersatilityWith a stated output of 45 packs per minute, the SMI SK450 T supports efficient shrink-film bundling of PET bottles for industrial packaging. The documented pack patterns provide flexibility for common beverage production formats, including compact 0.5L bundles and larger 0.75L and 1.5L bottle configurations. Shrink wrapping helps produce stable multipacks suitable for handling, storage, and onward palletizing.Installation Requirements & Site PreparationSite preparation should provide sufficient space for the shrink wrapper, heating oven, safe material flow, and access for operation and maintenance. The installation layout should account for bottle conveyors, film supply, bundle discharge, and connection to downstream packaging machinery. Electrical services and any required line utilities should be checked... Fjdpfx Aeztwl Iek Uopl

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, total length: 7,000 mm, total height: 2,200 mm, total width: 2,350 mm, input voltage: 380 V, overall weight: 1,700 kg, compressed air connection: 6 bar, warranty duration: 12 months, film width: 250 mm, power: 5.2 kW (7.07 HP), product height (max.): 850 mm, product height (min.): 50 mm, product length (min.): 650 mm, EDDA Olympia 150s BN | Automatic "Total Closing" Bubble Wrap & Stretch Wrapping Machine The Olympia 150s BN is a premium, fully automatic horizontal orbital wrapping machine featuring the innovative Total Closing Series technology. Engineered specifically for the furniture, door, panel, and wood-processing industries, it combines Bubble Wrap (Air Bubble Film) and Stretch Film application in a single inline process to provide 360° total protection for high-value or fragile products. Fjdsy D Nzlepfx Ak Uepl Advanced Total Closing & Dual-Layer Protection: Simultaneous Dual Coating: Applies a protective layer of bubble wrap followed immediately by an industrial stretch film layer, ensuring maximum cushioning against impacts and scratches. Complete 360° Sealing: Delivers a fully enclosed, airtight packaging result that safely protects products from dust, moisture, and transport damage. Optimized Material Efficiency: Precise mechanical/electronic tension control guarantees uniform wrapping while reducing film and bubble wrap consumption to the minimum. Premium Automation & High-End Components: Fully Automated Inline Cycle: Equipped with heavy-duty automatic film clamping, cutting, and welding units—completely removing manual operator dependency. Integrated Motorized Conveyors: Features driven inlet and outlet conveyor belts that sync perfectly with your factory line for smooth product transit. Pneumatic Top Press Rollers: Adjustable pneumatic vertical hold-down rollers secure the product firmly during high-speed rotation, preventing shifts. Intuitive PLC Touch Screen: Allows instant setup of wrapping parameters, ring rotation speed, and custom overlap configurations via a user-friendly interface. Industrial Heavy-Duty Build: Engineered with a balanced ring mechanism and rigid frame for exceptionally quiet, low-vibration, continuous 24/7 operations. For exact ring diameter dimensions, layout drawings, customized technical inquiries, or detailed catalog pricing, please send us an inquiry directly through Machineseeker.

Condition: used, Second-hand machine Fpedpfx Akezlbt Hj Usl Features and technical specifications: - Film material: LLDPE - Film width 500 m - Max. roller diameter 250 mm - max. film thickness 35 µm - Roller core diameter 76 mm - Max. pallet length 1,675 mm - Max. pallet width 1,675 mm - Max. pallet height 2,200 mm - Max. pallet weight 1,500 kg - with access ramp - Dimensions approx. 3000 x 2000 x 3200 mm - Weight approx. 750 kg Availability: at short notice Storage location: 63934 Röllbach