Used Brikett Press for sale (12,420)

Condition: ready for operation (used), Year of construction: 1986, functionality: limited functionality, machine/vehicle number: 97862034, installation height: 255 mm, sheet thickness (max.): 5 mm, working width: 180 mm, pressing force: 100 t, stroke length: 50 mm, TECHNICAL DETAILS Press force: 100 t Total force: 1,000 kN Ring tooth force: 40 - 310 kN Counterholder force: 10 - 270 kN Max. material width: 180 mm Max. material thickness: 5 mm Stroke rate (min.): 20 rpm Stroke rate (max.): 80 rpm Stroke: 50 mm Iodpfxeytcd Rj Ahvstd Feed unit Max. strip thickness: 5 mm Max. strip width: 180 mm Max. feed length per ram stroke: 999.9 mm Tensile force per feed (starting force): 6 kN Clamping force: max. 19 kN Max. feed height adjustment: +40 mm Max. distance between feed rollers: 20 mm Resolution, related to rollers: 0.1 mm MACHINE DETAILS Input voltage: 400 V Input frequency: 50 Hz Connected load: 13.5 kW Pump power: 3 kW Motor power: 3 kW Air connection: 6 bar Height adjustment type: hydraulic Dimensions & weight Dimensions (H x W x D): 2,420 x 2,325 x 1,665 mm Installation height: 255 mm Weight: approx. 6 t Year of last overhaul: 1997 EQUIPMENT Decoiler unit Two sets of tools Note: Further technical data for the machine can be found in the attached operating manual. The seller has repeatedly experienced issues with the processing and blow-off cycle. As a result, parts were not cleared out and the machine was stopped for safety reasons. However, the seller assumes this is merely a matter of adjustment. The seller recommends an overhaul of the control system in the long term.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 630213235, pressing force: 60 t, filling opening width: 650 mm, filling opening length: 1,195 mm, bale weight: 550 kg, overall weight: 2,450 kg, The machine is in mint condition! TECHNICAL DETAILS Isdpfsyqw Sqex Ahvstd Pressing force: 594 kN / 60 t Specific pressing force: 45 N/cm² Cycle time in idle mode: 25 s Theoretical pressing output (idle): 32.5 m³/h Filling height: 1,115 mm Filling opening dimensions: 1,195 x 650 mm Bale dimensions: 1,200 x 1,200 x 1,100 mm Maximum bale weight: 550 kg Material to be pressed: Film, mixed paper, cardboard, die-cut waste MACHINE DETAILS Drive power: 4 kW Voltage: 400 V Frequency: 50 Hz Door design: Sliding door Door lock: Hydraulic Feeding type: Manual Consumables: Wire, loop wire Dimensions & Weight Dimensions (L x W x H): 1,780 x 1,568 x 2,985 mm Machine weight: 2,450 kg FEATURES HSM TCS (Torsion Control System) for press plate tilt monitoring Automatic start of pressing process Specifications, information and technical data as provided by the manufacturer. Therefore, no guarantee given by the seller for their accuracy.

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Weinig Dimter Profipress C 2800 P - 6 m gluing press Manufacturer: Weinig Dimter Model: Profipress C 2800 P - 6 m Year of manufacture: 2009 Condition: Very good Machine description: For sale: Weinig Dimter Profipress C 2800 P - 6 m wood gluing press, year 2009, designed for the production of glued wooden panels and elements made of soft timber. The machine was developed for efficient production using PVAC glue in D2 / D3 class and allows processing of material within specified width, thickness and input length ranges. According to the documentation, this model can process timber with widths from 30 to 80 mm, thicknesses from 15 to 40 mm and input lengths from 2100 to 2800 mm. The machine allows the production of panels with variable widths from 600 to 1200 mm. For short lengths, the collecting distance range is 700 to 1400 mm. The output is up to 10 to 15 infeeds per minute, depending on the entrance width. The Profipress C 2800 P - 6 m is intended for processing soft timber. The permitted bending tolerance is maximum 5 mm per meter. The documentation also specifies recommended operating conditions, including room temperature from 15 to 30 degrees Celsius and air humidity in the range of 40 to 65 percent. Technical data: - Model: Profipress C 2800 P - 6 m - Year of manufacture: 2009 - Performance: max. 10–15 infeeds/min, depending on entrance width - Timber width: 30–80 mm - Timber thickness: 15–40 mm - Timber entrance length: 2100–2800 mm - Collecting distance for short lengths: 700–1400 mm - Panel width: 600–1200 mm - Timber type: soft timber - Permitted bending: max. 5 mm/m - Glue type: PVAC D2 / D3 - Recommended room temperature: 15–30°C - Recommended air humidity: 40–65% Features and advantages: - Press designed for glued panel production - Machine from the renowned Weinig Dimter brand - Output up to 10–15 infeeds per minute Itsdpoyvgiaofx Ahvsd - Possibility to produce panels with variable width - Suitable for processing soft timber - Works with common PVAC D2 / D3 glue - Industrial application for woodworking and production plants

Condition: like new (used), functionality: fully functional, machine/vehicle number: Geo Knight Maxi - Press, Year of construction: 2017, Please see PDF for detailed secifications: The Maxi Press AIR is an Automatic large format heat transfer press intended for more automated and higher pressure needs than the Manual version. The Maxi- AIR provides an oversized platen & a better production-oriented press with a single front loading table and high pressure pneumatic lifting system. This pressure system is powered by a dual air-bag, 10-ton, 20,000 lbs max force self leveling mechanism. The press is activated with a push of a button, and automatically releases at the end of the timing cycle. The front console Itedpfx Asv Dm Udehvod features the Digital Knight control, regulating digital temperature and digital automatic timing control, as well as full air pressure regulation. Ideal applications that the Maxi- AIR has performed flawlessly include: large fabrics & piece goods, full-bleed printed sportswear, banners, fl oor mats, carpets, mouse pads, plastics, sheet metal and much more. Most importantly, the 20,000 lbs of regulated applied force allow for deep embedding of materials such as TILES into nomex padding for full bleed wrap-around printing, as well as larger embossing applications. The Maxi- AIR strongly supports the sublimation transfer process, as well as digitally produced transfers, hot and cold peel plastisol transfers and large format laminating processes.

Condition: like new (used), Year of construction: 2017, functionality: fully functional, Training school display unit Itodpfxeyunphe Ahvsd VERY VERY seldom use For demo only, like new 1) Amada TP45FX 2) PATEC 110ton press with recoiler

Condition: good (used), Year of construction: 1987, functionality: fully functional, Clamping unit heating capacity, 1 heating rod / 8 heating rod: 0,48 / 0,9 kW clamping force: 2 x 500 kN heating plate dimensions: 550 x 600 mm piston stroke: 250 mm diameter of piston, main cylinder: 240 mm diameter of piston, locking cylinder. 39 mm locking cylinder: 260 mm Return capacity: 2 x 600 kN dimensions: 2600 x 2100 x 2100 mm Iedpjyv Et Ijfx Ahvotd weight approx.: 5 t

Condition: excellent (used), Year of construction: 2006, Dimensin: 2650 x 2100 x 2100 mm Isdpfx Ahjyv Etujvstd Clamping Force: 635 KN Working pressure: 206 bar Piston diameter: Ø200 mm Stroke: 140 mm Daylight: 150/180 mm Heating plant dimension: 250 x 300 mm Max. mass of heating plant: 70 kg Oil reservoir: 100 l Rated power: 19.66 kW Heater capacity: 9.6 kW Vacuum motor power: 2,6 kW Between light curtain and mould area: 270 mm Stroke of vacuum cover: 140 mm The vulcanizing press from manufacturer PAN STONE, model S-V-65-2RT-PCD, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. The machine was part of a production line responsible for manufacturing high-performance seals used in various industries. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: good (used), Year of construction: 1997, Clamping Unit: Clamping force: 7,000 kN Operating pressure: 250 bar Specific pressing pressure: 610 N/cm² Number of levels: 2 Installation height with 75 mm heating plate & 20 mm insulating plate: approx. 2x 190 mm Piston stroke: approx. 400 mm Isdpsyv Etnefx Ahvjtd Piston 1 diameter: 543 mm Clamping force, rapid traverse: approx. 2 x 85 kN Retraction force: approx. 2 x 47 kN Operating pressure: 300 bar Piston 2 diameter: 60/40 mm Stroke: 400 mm Estimated weight: approx. 16 tonnes Hydraulic System: Pressure adjustment: 40 - 300 bar Flow rate regulation: 0 - 99 % Flow rate l/min (HD): 45 against 300 bar Drive power: 22 kW Tank dimensions (LxWxH): 1000 x 770 x 535 mm Closing Speed: Rapid traverse: approx. 40 - 50 mm/s Slow closing: approx. 0 - 20 mm/s Pressing speed: approx. 0 - 3 mm/s Slow opening: approx. 0 - 20 mm/s Opening, rapid traverse: approx. 0 - 60 mm/s

Condition: used, Year of construction: 2005, functionality: fully functional, Clamping force: 4900 kN Working pressure: 206 bar Heating plate dimensions: 700 x 700 mm diameter of piston: 558,8 mm max. stroke: 250 mm daylight: 300 mm max. mass of heating plant: 560 kg capacity of oil tank: 1100 l rated capacity: 82 kW heating capacity: 56 kW enginge output, vacuum motor: 4 kW Stroke of vacuum cover: 200 mm dimensions: 3975 x 2935 x 2555 mmm Ijdpfxeyv Erwe Ahvstd Equipped with a crane runway (monorail) with three chain hoists Producer: STHAL Year: 2011 Lifting capacity: 3 x 400 kg Lenght of crane runway: ca. 3500 mm Rolling chassis Lifting capacity: 400 kg Lifting height: 3000 mm stroke speed - main stroke: 4 m/min stroke speed - fine stroke: 1 m/min The vulcanizing press from manufacturer PAN STONE, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: excellent (used), Year of construction: 2003, Haco 6m x 225ton CNC Pressbrake Great working condition 6m capacity x 225ton Iodpoyv Dc Iefx Ahvotd 2 Axis Year 2003 Light Guards

Condition: good (used), functionality: fully functional, Year of construction: 2008, Equipment: documentation/manual, safety light barrier, Hydraulic Press Brake Make: TRUMPF Model: TruBend 5050 Year: 2008 Technical Data Manufacturer: TRUMPF Itodpfjyv A R Rex Ahvjd Model: TruBend 5050 Year of manufacture: 2008 Working length: 1275 mm Press force: 50 t Clear throat: 1040 mm Stroke: 215 mm Throat depth: 410 mm Installation height: 385 mm Working height: 1085 mm Rapid traverse Y-axis: 200 mm/s Y working speed: 1-20 mm/s Y return speed: 220 mm/s Dimensions LxWxH approx.: L 2.20 x W 1.80 x H 2.40 m Weight: approx. 4.9 t Equipment: - Control: TRUMPF TASC 6000 - Controlled axes: X, R, Z1, Z2 - 2 movable support arms - Pneumatic die shifting - Hydraulic tool clamping (top with LED display + bottom) - Lasersafe light curtain (front) - Upper tool OW202/K 28°/R1, H 120mm, L = 1,275 mm, segmented - Lower tool EV/S-W12, 84°/R1, H 100mm, L = 1,275 mm, segmented - Documentation including service manuals All information provided without guarantee. A demonstration under power is possible at any time in our showroom.

Condition: used, 2 Farben Offsetdruckmaschine / 2 Color Sheet-Fed Offset Press PM-QM46-2 N+P Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test Itjdpfx Ahsyv A S Usved

Condition: good (used), Year of construction: 2019, Gebruikte 3,6 meter CNC-kantbank van Haco Model: ERM 36150 Bouwjaar: 2019 Capaciteit: 3600 x 150 ton Itsdsyv A Ehjpfx Ahved Voorzien van Fastbend 2D-besturing op de Y1-, Y2- en X-as Euro-gereedschapsklemsysteem en een complete gereedschapset.

Condition: used, Year of construction: 1998, machine/vehicle number: 1 / 2000, Pressure total: 2000 ton Ram stroke: 900 mm Slide adjustment: 800 mm Shut height (stroke down, adjustment up): 1800 mm Free frontal opening L-R: 5040 mm Distance between oil tray: 4840 mm Distance between the columns F - B: 2600 x 2400 mm Table surface area : 5000 x 2700 mm Slide area: 5000 x 2700 mm Die cushion capacity in table: 400 ton Die cushion stroke: 350 mm Die cushion pad area: 4200 x 2100 mm Cushion pressure in ram: 200 ton Ejector stroke in ram: 200 mm Number of strokes: 8 - 14 s.p.m. Required power: 350 kW Itjdpoyvz U Iofx Ahvsd Height over floor approx.: 11350 mm Die weight at the ram max.: 40000 kg Die Weight total: 80000 kg Weight of machine approx.: 580 ton Standard configuration Moving bolster front sidePin diameter 52 mmForce in microinches = 400 tA SIEMENS control system is installed The documentation is available.A packing list would be available, as an identical press has already been dismantled.

Condition: used, Year of construction: 1998, machine/vehicle number: 2 / 2000, Pressure total: 2000 ton Ram stroke: 900 mm Slide adjustment: 800 mm Shut height (stroke down, adjustment up): 1800 mm Free frontal opening L-R: 5040 mm Itsdpfjyvz Stex Ahvjd Distance between oil tray: 4840 mm Distance between the columns F - B: 2600 x 2400 mm Table surface area : 5000 x 2700 mm Slide area: 5000 x 2700 mm Die cushion capacity in table: 400 ton Die cushion stroke: 350 mm Die cushion pad area: 4200 x 2100 mm Cushion pressure in ram: 200 ton Ejector stroke in ram: 200 mm Number of strokes: 8 - 14 s.p.m. Required power: 350 kW Height over floor approx.: 11350 mm Die weight at the ram max.: 40000 kg Die Weight total: 80000 kg Weight of machine approx.: 580 ton Standard configuration Moving bolster front sidePin diameter 52 mmForce in microinches = 400 tA SIEMENS control system is installed The documentation is available.A packing list would be available, as an identical press has already been dismantled.

Condition: good (used), Year of construction: 2005, control type: CNC control, controller manufacturer: Delem DA65, bending force (max.): 175 t, working width: 3,100 mm, distance between stands: 2,550 mm, operating speed: 10 mm/s, number of axes: 5, overall weight: 11,500 kg, total length: 4,000 mm, total width: 2,000 mm, total height: 3,000 mm, power: 15 kW (20.39 HP), Max. bending length: 3100mm Distance between column: 2550mm Max. pressing force: 175T Beam stroke: 225mm Table Width: 150mm Troth beam: 400mm Approch speed: 100mm/min. Working speed: 10mm/min. Return speed: 100mm/min. Adjustment X-Axis back gauge:1000mm Number of controlled axis: 5 Control: yes Crowning: yes Hydraulic toolclamping: yes Power: 15kW Length: 4000mm Isdpfsyvz H Rsx Ahvstd Width: 2000mm Height: 3000mm Weight: 11500kg

Condition: new, Year of construction: 2024, Bending capacity: 60t Bending length: 1250 mm Distance between uprights (mm): 1050 Material thickness: 7.5 mm Stroke length (mm): 265 Throat depth: 410 mm Installation height: 530 mm Operating speed Y (mm/sec.): 10 Motor power (kW): 7.5 Operating speed X (mm/sec.): 250 Length (mm): 2300 Width (mm): 1550 Height (mm): 2750 Weight (kg): 3,100 Standard equipment: Y1, Y2, X, R (4 axes) X = 650 mm X, R Iodpfod E If Sox Ahvetd Control unit: DURMA DT15 European clamping system 60 mm die holder (only for European dies) Throat depth: 410 mm Backgauge: Siemens DC servo-driven, linear guide & ball screw system Protective cover Special accessories: European upper tool P97.75.R08 (one in segmented design) European lower tool M.460R.85 (one in segmented design) DURMA quick clamping system CE with manual F.AKAS II M -FPSC-B-C + safety cover & switch Other machines are available for demonstration at our Staufenberg location. Further information available upon request.

Condition: new, Year of construction: 2024, Bending force: 320 t Year of construction: 2024 (new) Control system: DT 15 Bending length: 4050 mm Distance between the columns: 3600 mm Y fast Speed: 100 mm / s Y Working speed: 10 mm / s Y Retraction speed: 100 mm / s Motorized crowning Itsdpfx Ahoff Hvlsvod Table length: 630 mm Table width: 154 mm Table height: 900 mm Stroke: 365 mm Projection: 450 mm 2 support arms 2 back gauge fingers Travel speed X-axis: 350 mm / s Travel in X-axis: 750 mm Travel speed in R-axis: (max.) 300 mm / s Travel distance R-axis: 250 mm Standard equipment: Y1, Y2, X (3-axis) Y1, Y2, X = 650 mm (double guide, aluminum) D-BEND software for 3D bending simulation and alignment Manual crowning R-axis, manual Backgauge with motor and linear guide and ball screw thread Stop finger back gauge with height adjustment (R-axis, manual) CE die holding system (upper dies) Front support arms for sheets, sliding (with T-channel and stops) Hydraulic blocks and valves in special design, in accordance with global standards Electrical equipment, in accordance with global standards Option: CE certified Motorized crowning and X & R backgauge Engine power 37 kW Oil tank capacity 250 lt Length 5300 mm width 1910 mm Height 3230 mm Weight approx. 20000 kg

Condition: new, Year of construction: 2024, Are you looking for a powerful press brake that can meet even the most demanding requirements? Then the Durma AD-S 803000 press brake with 3000 tons of pressure could be the perfect solution for your needs. With an impressive length of 8 meters and a stroke of 750 mm, this machine is capable of processing even large and heavy materials with the highest precision. The installation height of 1000 mm allows flexible and comfortable positioning of the workpiece. The heart of the machine is the DELEM-DA 66T movable control system, which ensures intuitive operation and precise control of the workflow. In addition, the press brake is a special design and can be configured according to customer requirements to meet all individual needs. If you are interested in Durma press brake, we are at your disposal for personal consultation. Iodsi Da Syepfx Ahvjtd Other machines are also available and can be visited. Feel free to contact us for more information and let's find a customized solution for your needs together. Control type: DELEM DA-66T Protection oil: suitable for sea transport Front safety system: FPSC (MANUEL) Sheet metal support system: sliding support arm Stroke: 750 MM Backgauge type: X=1500 X, R Overhang:1050 MM Crowning: Hydromechanical Installation height: 1000 MM Power: 400V 50HZ Body type: Welded frame Under tool holder: DURMA Wide

Condition: new, Year of construction: 2024, Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Technical data: Bending force: 600 tons bending length: 6050 mm passage between the uprights: 5100 mm stroke: 365 mm Installation height: 700 mm Projection: 510 mm table height: 990 mm table width: 154 mm Y High speed: 80 mm Y Working speed: 7 mm/sec. Y retraction speed: 80 mm/sec. X axes working speed: 350 mm/sec. R axes working speed: 300 mm R Axes travel distance: 250 mm X axis distance: 750 mm Engine power: 55 kW Iedpfofir U Njx Ahvstd length: 8050 mm width: 3200 mm height: 4250 mm Weight: 72000 kg Standard equipment Y1, Y2, X, R - 4 axes Control unit - CNC ModEva15T Servo motor backgauge & linear guided ball screw system (X-R) CNC Crowning European type tool clamping system Movable support arms (with T-slot and stopper) Specially designed hydraulic block and valves according to worldwide standard electrical equipment according to worldwide standard Optional equipment Control unit - ModEva Premium , 69T and 66T CE Manuel F. AKAS II M FPSC-B-C + safety covers with switch CE F. AKAS-LC II AKAS-3 M Motorised + FPSC (Safety PLC) CE BLVT safety - only for tandem machines Z1, Z2 Axes X1, X2 Axes Bil0h3uvee R1, R2 Axles Delta X axis, +/- 250mm stroke or +/- 125mm CNC controlled X axis = 1000 mm - rear protection with light barrier AP3-AP4 Bending aid Height-adjustable laser angle measurement

Condition: new, Year of construction: 2024, Bending force: 320 t Year of construction: New (delivery time 6-8 weeks) Control: DT 15 bending length: 3050 mm distance between the columns: 2600 mm Y Fast speed: 160 mm / s Y Working speed: 10 mm / s Y Retraction speed: 140 mm / s Motorized crowning table length: 630 mm table width: 154 mm table height: 900 mm stroke: 365 mm Projection: 410 mm 2 support arms 2 Backgauge fingers Travel speed X-axis: 250 mm / s R-axis working speed: (max.) 140mm / s R-axis travel: 250 mm Standard equipment: Y1, Y2, X (3-axis) Y1, Y2, X = 650 mm (double guide, aluminium) Software D-BEND for 3D bending simulation and alignment Isdpfx Ahefifg Hevjtd Manual crowning R axis, manual Backgauge with motor, linear guide and ball screw Backgauge with height adjustment (R-axis, manual) CE-die holding system (upper dies) Front support arms for sheets, sliding (with T-channel and stops) Hydraulic blocks and valves in special design, according to the worldwide applicable standards Electrical equipment, in accordance with the standards applicable worldwide Option: CE standard with manual fussler AKAS II M -FPSC-B-C (SAFETY PLC) CNC motorized crowning Y1, Y2, X, R (4 axes) CNC motorized crowning Engine power 37 kW Oil tank capacity 250 lt length 4300 mm Width 1820 mm Height 3230 mm Weight approx. 17250 kg

Condition: new, Year of construction: 2024, Press brake AD-S 40220 | 4 meters 220 tons Everything can be configured on request, very short production and delivery times. We will be happy to send you further information on request. Technical data: Bending capacity: 220 tons Bending length (mm): 4050 Passage between uprights (mm): 3600 Stroke (mm): 265 Installation height (mm): 530 Projection (mm): 410 Table height(mm): 900 Table width(mm): 104 Y Rapid traverse (mm/sec.): 160 Y Working speed(mm/sec): 10 Y Retraction speed(mm/sec.):140 X axles working speed(mm/sec.): 250 R axes working speed (M): 140 R axes travel distance: 250 X axes distance(mm): 650 Motor power: 22 kW Length: 5250 mm Width: 1770 mm Height: 2900 mm Weight: 14750 kg Standard equipment Control system: CNC Cybelec ModEva 19T CNC controlled motorized crowning European tool clamping system / or Durma clamping system on customer request Extended equipment: Safety system CE standard for EU: FIESSLER AKAS II M-FPSC-B-C (SAFETY PLC) Controlled axes backgauge: X1,X2,R1,R2,Z1,Z2 Control unit: DELEM DA-66T Delem 66T - 69T or Durma control is selectable Isdpfefirx Djx Ahvstd DAM - Durma angle measuring system Hydraulic upper tool clamping Wila NSCL-I-HC/UPB - PRO - 180 t/m Hydraulic lower tool clamping Wila NSCR-I-HC-CNC/UPB - PRO Powerpack for hydraulic clamping D-BEND 3D CAD/CAM import & simulation program AP3 & AP4 bending aid 750mm to 1500 mm selectable Parking area for support arms (1000mm) TANDEM preparation Laser bending line Oil heating Manual or motorized central lubrication Air conditioning for control cabinet

Condition: new, Year of construction: 2024, operating hours: 32 h, Make: DURMA Type: AD-S 30135 Year of construction: 2018 Folding length: 3050 mm Pressing force: 1350 kN Control: CNC DT-15 Operating hours: 0 h Controlled 3 axes: Y1,Y2, X Clearance between the stands: 2600 mm Stroke length: 265 mm Installation height: 530 mm Table width: 104 mm Table height: 900 mm Stand projection: 410 mm X-axis travel range: 650 mm (double guide, aluminum) Traversing speed X-axis: 250 mm/s Infeed speed: 160 mm/s Folding speed: 10 mm/s Retraction speed: 120 mm/s Dimensions L/W/H: approx. 4200x1680x2750 mm Weight: approx. 10250 kg Standard equipment Y1,Y2, X=650 mm Control: CNC DT-15 Manual crowning European die clamping system 60 mm die holder (only for European die system) 2 support arms movable from the front with linear guide along the entire length Backgauge: motorized with linear guide & ball screw spindle Backgauge finger height-adjustable, R-axis manual Backgauge motor servo Safety covers on the side CE marking Iodpfjdx Rd Nsx Ahvstd Extended equipment CE safety system with manual FIESSLER AKAS II M-FPSC-B-C+safety cover & switch The machine can be viewed and demonstrated at any time by appointment at our demonstration center in Staufenberg. Further machines are available for demonstration at our demonstration center in Staufenberg. We will be happy to send you further information on request.

Condition: new, Year of construction: 2024, Make: DURMA Type: AD-S 30175 Year of construction: 2020 Folding length: 3050 mm Pressing force: 1750 kN Control: CNC DT-15 Operating hours: 33 h Bcq29blmc8 Controlled axes back gauge: X,R Clearance between the uprights: 2600 mm Stroke length: 265 mm Installation height: 530 mm Table width: 104 mm Table height: 900 mm Stand projection: 410 mm X-axis travel range: 650 mm Itsdpfx Aod Srk Sjhved Traversing speed X-axis: 250 mm/s Infeed speed: 160 mm/s Folding speed: 10 mm/s Retraction speed: 100 mm/s Dimensions L/W/H: approx. 4250x1700x2750 mm Weight: approx. 11500 kg Standard equipment Y1,Y2, X=650 mm Control: CNC DT-15 European die clamping system 60 mm die holder (only for European die system) 2 support arms movable from the front with linear guide along the entire length Servo motor backgauge Safety covers on the side CE marking Extended equipment Safety system CE with manual FIESSLER AKAS II M-FPSC- Controlled axes X,R-axis, Z-axes manually adjustable CNC controlled motorized crowning European upper tool/lower tool from Rolleri The machine can be viewed and demonstrated at any time by appointment at our demonstration center in Staufenberg. Further machines are available for demonstration in Staufenberg. We will be happy to send you further information on request.

Condition: new, Year of construction: 2024, Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Technical data on request. AD-R 80400 Bending force: 400 tons bending length: 8050 mm With more than 60 years of experience in research and production of machines for sheet metal working, 8,000 machines produced annually in three technologically advanced production facilities covering a total area of 150,000 m², the Durmazlar Group and its DURMA machines are today among the internationally renowned manufacturers in their sector, whose products are sold in 120 countries. With the branch in Staufenberg near Gießen, Durma Maschinen GmbH is now an important part of the Central Hesse region. Here here we are your direct contact person from the ranks of Durmazlar, who will competently assist you with advice and practical support when it comes to machines for sheet metal processing. Our demonstration centre gives you the opportunity to get an overview of our machines on site, to be convinced of the quality and precise technology of our products at first hand and to receive the best possible advice that is geared to your company goals. It is our task to be your direct contact person for you, our customer, on site and to offer you services in the areas of training and customer service. We are now happy to accompany you from Germany - from advice, through the purchase and di Ijdpfx Ahjfin N Sovotd