Used Bellow Actuator for sale (735)

Condition: new, machine/vehicle number: f044065451f6d849ee7a5b9f8, empty load weight: 5 kg, maximum load weight: 29 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 385 / 65 r 22,5, Further information Chassis semi-trailer forwarding Welded steel construction in reinforced design, only 2 side members as double T-beams with steel/checker plate between the side members, saddle plate with replaceable 2 kingpins. Protective plate for rear lights. 1 steel storage box, recessed between side members 8 pairs of lashing eyes bolted or welded to the frame at the manufacturer's choice 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EC 1 spare wheel holder for 1 e-wheel, with wheel fastening set 8 wooden stanchions of the manufacturer's choice, bolted to frame with 2 wooden stanchions each, telescopic from 1800 to 2800 mm, per pair 7 to. Axles + suspension SAF disk brake axles with 430 mm disk diameter Air suspension with lifting & lowering valve, safety cable on the axles 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle spacing offset mm (combined transport) up to 44 tons gross train weight Wheels and tires 385 / 65 R 22,5 at the manufacturer's discretion Steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installed (no calibrated scales) 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Front bulkhead/front stanchions Steel/grid bulkhead, approx. 2,300 mm high, bolted to the frame Approval / plates Blodpfxsi Rivwo Acyjp Country of approval: Germany Approval according to EC 2007/46 Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Black coated support legs Front wall hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: eca976917d325d4adc41b69e8, empty load weight: 7,200 kg, maximum load weight: 27,800 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r 22,5, Further information Chassis semitrailer forwarding Fine-grained steel welded construction in lightweight design, fifth wheel plate with replaceable 2 king pins, main frame reinforcement for 25 tons in the centre of gravity on 3 m loading length when pushed together. Bjdpfei Ri Szex Acyolp 13 pairs of hooks for lashing strap attachment welded onto the cross members 23 pairs of lashing eyes embedded in the outer frame, 3.5 tons each Outer frame with Load-Lock profile for lashing strap attachment Please note! Cannot be used with drop sides! 24 t. 2-speed support winch in reinforced design for loaded trailer, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Wheel chocks with holder Aluminum side bumper Underride guard Half-shell mudguards with anti-spray flaps according to EG 1 spare wheel holder for 1 electric wheel, with wheel mounting kit 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/H=400/420 mm/t=2460 mm 6 pairs of extendable stanchion pockets, for 80x80 mm tubular stanchions, extendable from loading width 2000 mm to 3100 mm 4 pairs of stanchion pockets embedded in the outer frame, for 80x80 mm shaped tubes 11 stake pockets centrally recessed in the floor, for 80x80 mm shaped tubes, with reinforcement beam, each installed between the outer stake pockets 5 x 3 pairs of stanchion pockets recessed on the outside of the longitudinal beams, for 80x80 mm shaped pipes, including reinforcement beams - for securing loads to the front and rear when transporting 2x5000 mm or 2x 6000 mm construction steel mats 6 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, top with cable guide for belt tensioning 12 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, with lashing eyes welded to the bottom on both sides Note: stanchion pockets / stanchions are not designed for securing long materials, pipes etc. on their own without looping around them 2 plastic toolboxes, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 6 construction steel winches with wire rope and counter hooks, with rope feed-through through the outer frame, 1 removable slip-on gear for construction steel winches - supplied loose (without bracket on the frame) Telescoping Main frame can be telescoped Extendable by max. 4,000 mm and can be arranged approx. every 500 mm Locking with pneumatic bolt locking + display Frame locking on both sides, actuation via hand knob, operation for brake/locking and suspension in FR-left in front of the axles Storage compartment between the side members when extended Axles + suspension SAF disc brake axles with 430 mm disc diameter Last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button, as well as manually via switch in the towing vehicle (pin 10), without truck installation. Offset axle spacing mm Air suspension 1st axle automatic lift axle, can also be operated electrically from the truck, with starting aid, without truck installation (starting aid is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS make of the manufacturer's choice, electronic brake syst

Condition: new, machine/vehicle number: 74dd481d88dffaf9218e6ee58, empty load weight: 5,150 kg, maximum load weight: 29,850 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Patented curved front end Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Bljdpfx Aei Ri A Iocyjp with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Standing platform with step, connection plate for air/electric and brake with large clearance for optimum operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty

Condition: new, machine/vehicle number: efdaf8862775f9506d97b86a5, empty load weight: 5,600 kg, maximum load weight: 29,400 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Blodpfji Ri Ihox Acysp Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall pendulum-mounted with double-joint hinge and with 2-leaf door partition 1/2 to 1/2, with pivoting gallows at the top, with one grain slider per door. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 Novagr

Condition: new, machine/vehicle number: d73a4869e108da5fdd6e55526, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, saddle plate with interchangeable 2 kingpins and 2 kingpin positions Container mountings: Rear extension retracted: 1 x 20 feet or 1 x 30 feet Rear flush Center telescope 1st stage, rear extension extended 1st stage: 2 x 20 feet or 1 x 40 feet with and without gooseneck tunnel Center telescope 2nd stage, rear extension extended 2nd stage 1 x 45 feet with gooseneck tunnel and overloaded to the rear Center telescope 2nd stage, front extension extended 1st stage Rear extension extended 2nd stage 1 x 45 feet with long gooseneck tunnel and chamfered corners Center telescope as an interlocking central tubular frame with bolt lock without height adjustment at the rear and without folding center supports, no transport of containers without tunnel possible. 2 container guides, incl. connection plate for electrical, air and brake connections (connections positioned upwards) Plug-in adapter for front locking, for locking the containers without tunnel from below, with holder when not in use Front extension mounted on castors, can be pulled out manually (for 45 containers with long tunnel) Rear extension mounted on rollers, with hand crank 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Blodpfx Asi Ri E Ascyop 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Extendable underride guard for 45 foot containers Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, 4 x 3 chamber lights + 1 round reversing light and + 1 round rear fog light, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Operating instructions When transporting 45 containers with a short tunnel, with or without front extension, the permissible system length from the kingpin to the rear edge of the vehicle and the total train length of 16500 mm is exceeded! The underride guard must be extended manually! A special permit in accordance with § 70 StVZo is required! Approval / plates Germany Test approval according to EG 2007/46 24/7 service hotline Prepared for single-line license plate holder Warning sign according

Condition: new, machine/vehicle number: 0fe2184cda24503447c582a1e, empty load weight: 3 kg, maximum load weight: 34 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r 22,5, Further information Chassis semi-trailer container Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Container mounts:1 x 40 feet with gooseneck tunnel The transportation of filled tank containers is excluded. Without rear height adjustment and without folding center supports, no transport of containers without tunnel possible. Container guide front plug-in 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Blsdoi Ri Ayspfx Acysp Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting on the side (Note! with certain towing vehicles, misdiagnosis may occur although the function is given) 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable LED work lights on both sides (switched via reversing light) Additional LED work light(s) at the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Special approval required if the overall length of the train exceeds 16,500 mm. Attention: Transport of filled tank containers is excluded! Country of approval / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Support legs coated black Without pallet box Paint Attention: Archive pictures!

Condition: new, machine/vehicle number: 1f4581c873ed977cb9602039b, empty load weight: 3 kg, maximum load weight: 34 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis semi-trailer container Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Container mounts: 1 x 20 foot centered (or swap body container 7.15 / 7.45), not retractable at the front, the pivot pins of the container lock in the longer version 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Side collision protection Aluminum underride guard Half-shell mudguards with anti-spray flaps according to EG VA drip tray with 1 1/4 inch drain pipe + 1 1/4 inch stopcock, incl. drip tray, with perforated tread plates, approx. 400 mm wide, left + right between drip tray and side member 4 hose trays approx. 4500 mm long (hose box) for hose pipes 2 x DN 200 outside + 2 x DN 160 centrally arranged, rear hose box (stainless steel) 300 mm deep, splash-proof, cover (stainless steel) with rubber seal all round, with drain hole at lowest point, then without cover on hose pipes 1 stainless steel earthing lug at the rear in FR on the right of the frame, with international earthing sticker on the frame, Steps at the rear right on the underride guard, at the rear in FR right on the outside of the main beam, tread plate approx. 260 mm long and 300 mm wide, Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system Blodpfx Acsi Rixkjyop 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) This vehicle may only be loaded with 20' tank containers that comply with ISO 668 and in particular ISO 1496-3! The tank containers must have "end-load-transfer areas"! Country of approval / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Approval according to ADR acc. to 9.1.1.2 of ADR, EX/II, EX/III / certificate of approval for vehicles for the transport of certain dangerous goods (ex.B3) with warning sign at the rear, not valid for substances according to UN 0331 and 0332 (explosives B-E) Contour marking with refle

Condition: new, machine/vehicle number: 45d76d32267904923b7adcdea, empty load weight: 4,980 kg, maximum load weight: 30,020 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Bljdpfji Ri Idox Acyop Integrated mudguard holder Surface stone-repellent Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Polished aluminum rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 5 mm thick throughout, Brinell 110Note! Only for transporting sand, grit and rolled gravel with a maximum grain size of up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with step, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Revolution Link: Revolution Link experience report: Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 0

Condition: new, machine/vehicle number: a203d9a559ff6484cf2a14c1f, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, fifth-wheel plate with replaceable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with guide wedges on both sides, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 20 foot or 1 x 30 foot container. (Note! low fifth wheel load for 20 foot containers) Adjustment via central telescope as an interlocking central tubular frame with pin lock. 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1850 mm 2 wheel chocks with holder Half-shell mudguard with anti-spray flaps according to EG Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Bledpfx Acji Ri Avoyop Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/65 R22.5 Manufacturer's choice Steel rims, factory silver Incl. Electrics 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Additional LED work light(s) at the rear, switched via reversing light Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Support legs coated black Attention: Archive pictures!

Condition: new, machine/vehicle number: 8df1ead53cc82aeb51e50a37d, empty load weight: 4 kg, maximum load weight: 13,880 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis Turntable Disposal Fine-grained steel welded construction Container locking system: - 2 pairs of locking hooks embedded in the floor - Pneumatic actuation The container locking mechanism is a 2-point design, acting from the inside, and locking of roll-off containers with an inner web is not possible (for transporting roll-off containers with a sub-frame in accordance with DIN 30722) Blsdpfxei Ri Nus Acyop Note! At the start of the roller recess at the front, the container must be pushed on completely flat! Longitudinal guide rails can be moved sideways and removed, rails approx. 115 mm high Turntable with strong ball bearing slewing ring 8 pairs of lashing mushrooms at the top and sides of the outer frame, 5 tons each 7 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Quarter-shell mudguards according to EG with anti-spray flaps according to EG Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Steel floor Roller recess for container recessed in the floor at the frontfor roll-off containers from 5,000 - 7,000 mm in length Note: Slight floor undulation possible due to welding distortion! Drive-on ramps Lockable storage space for loading ramps underneath the loading area Operating instructions A special permit is required for axle loads of 10,000 kg. Approval must be applied for individually in each federal state; the legislator does not have to grant approval for 20 t GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB 7350 nova gray 15-year warranty against rusting through Note: Bottom corrugation possible due to hot-dip galvanizing! Drawbar KTL black Attention: Archive pictures!

Condition: new, machine/vehicle number: 28b2dda4ac4da850b1010673a, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, fifth-wheel plate with replaceable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with guide wedges on both sides, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 20 foot container (Note! low fifth wheel load for 20 foot containers) 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1850 mm 2 wheel chocks with holder Half-shell mudguard with anti-spray flaps according to EG Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK Screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension Blodpfji Ri Eusx Acysp 3 SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons Gross train weight Air suspension. Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck instal. calibrated scales) Wheels and tires 6 385/65 R22.5 tires of the manufacturer's choice 6 steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Country of registration/ plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Support legs coated black Attention: Archive pictures!

Condition: new, machine/vehicle number: 6e7907b4000c16661fa1c8a1f, empty load weight: 4,150 kg, maximum load weight: 30,850 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Without support leg Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Polished aluminum rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 5 mm thick throughout, Brinell 110Note! Only for transporting sand, grit and rolled gravel with a maximum grain size of up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with step, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Revolution Link: Revolution Link experience report: Country of registration / plates Bledji Ri Arjpfx Acyjp Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Body R

Condition: new, machine/vehicle number: 7dbf076fea9ec110acb399f8f, empty load weight: 5 kg, maximum load weight: 32 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, saddle plate with interchangeable 2 kingpins and 2 kingpin positions Container mountings: Rear extension retracted: 1 x 20 feet or 1 x 30 feet Rear flush Center telescope 1st stage, rear extension extended 1st stage: 2 x 20 feet or 1 x 40 feet with and without gooseneck tunnel Center telescope 2nd stage, rear extension extended 2nd stage 1 x 45 feet with gooseneck tunnel and overloaded to the rear Center telescope 2nd stage, front extension extended 1st stage Rear extension extended 2nd stage 1 x 45 feet with long gooseneck tunnel and chamfered corners Center telescope as an interlocking central tubular frame with bolt lock With rear height adjustment and folding center supports for containers without tunnel Container guide at the front Plug-in and removable (electrical, air and brake connections at the front of the front cross member) Plug-in adapter for front locking, for locking the containers Without tunnel from below, with holder when not in use Front extension mounted on rollers, can be pulled out manually (for 45 containers with long tunnel) Rear extension mounted on rollers, with hand crank 24 t. 2-speed support winch, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Extendable underride guard for 45 foot containers Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting on the side (Note! with certain towing vehicles, misdiagnosis may occur although the function is given) 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Operating instructions Blodpfsi Ri R Sox Acysp When transporting 45 containers with a short tunnel, with or without front extension, the permissible system length from the kingpin to the rear edge of the vehicle and the total train length of 16500 mm is exceeded! The underride guard must be extended manually! A special permit in accordance with § 70 StVZo is required! Country of registration / plates Germany Test approval according to EG 2007/46 24/7

Condition: new, machine/vehicle number: 074630ca1b8dc2d710f82c15a, empty load weight: 3,980 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Without support leg Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Polished aluminum rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 5 mm thick throughout, Brinell 110Note! Only for transporting sand, grit and rolled gravel with a maximum grain size of up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with step, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Bedpoi Ri H Ssfx Acyolp Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Revolution Link: Revolution Link experience report: Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Body R

Condition: new, machine/vehicle number: 3703d600260244d5f159f51e4, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, saddle plate with interchangeable 2 kingpins and 2 kingpin positions Container mounts: Incl. Rear extension retracted: 1 x 20 feet flush with the rear, attention low fifth wheel load Rear extension extended 1st stage: 1 x 30 feet, 2 x 20 feet, 1 x 40 feet with gooseneck tunnel Rear extension extended 2nd stage: 1 x 45 feet with gooseneck tunnel and overloaded to the rear without rear height adjustment and without folding center supports, no transport of containers without tunnel possible. Plug-in adapter for front locking, for locking the containers without tunnel from below, with holder when not in use Rear extension mounted on rollers, with hand crank 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Extendable underride guard for 45 foot containers Half-shell mudguards Incl. with anti-spray flaps according to EG Impact protection at the rear Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Bjdpfxei Ri Eqs Acyjlp Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored line routing for easy service. 200 spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting on the side (Note! with certain towing vehicles, misdiagnoses can occur even though the function is is given) 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Operating instructions Attention: Transport of filled tank containers is excluded! When transporting 45 containers with a short tunnel, with or without front extension, the permissible system length from the kingpin to the rear edge of the vehicle and the total train length of 16500 mm is exceeded! The underride guard must be extended manually! A special permit in accordance with § 70 StVZo is required! Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder 390 Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Support legs coated black Attention: Archive pictures!

Condition: new, machine/vehicle number: 562ca26c733cc91276e95b716, empty load weight: 6,700 kg, maximum load weight: 28,300 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/55 r22.5, Further information Chassis saddle forwarding Fine-grained steel welded construction in lightweight design, up to the support legs, saddle plate with replaceable 2 king pins Laterally in the floor with lashing eye preparation (max. 13 pairs) 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Extension ladder at the rear Door retainer on the side 2 wheel chocks with holder Aluminum side bumper Steel underride guard with wide Fliegl mud flaps Folding guard plate for light unit Quarter-shell mudguards Impact protection at the rear Aluminum ladder approx. 3,550 mm, with holder on the side Tarpaulin pole with bracket 1 plastic tool box, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 1 spare wheel holder for 1 e-wheel, with wheel fastening set Axles+suspension SAF disc brake axles with 430 mm disk diameter Axle/suspension laser-measured Reduction in tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/55 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides Bljdsi Riywopfx Acyjp 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable SB Hydraulics Hydraulic cylinder with sliding device installed in the floor. 2-circuit hydraulics. Forward/reverse travel is switched electrically via remote control with cable. -Moving floor Power supply via parking light Hydraulic actuation via truck power take-off Hydraulic connection with hose to front wall and HDK screw connector NW = 48 mm, Note: A 2-circuit hydraulic system is required! Recommended pump capacity: Liter capacity: 110 ltr/min Pressure: 250 bar Oil tank filling min: 100 ltr SB floor Sliding floor with wear plate at the rear Aluminum floor boards, 8 mm floor profile, ribbed design SB Trough Aluminum box body made of high-quality, abrasion-resistant material. Front and side walls made of hollow aluminum profiles, welded together all round at the top with a wide special aluminum reinforcement profile, welded in at the bottom with a special frame. Sliding wall for better emptying of the load, with reinforced tarpaulin flaps at the bottom. With rail cleaner Rear wall made of hollow aluminum profiles, as a 2-leaf door, with 1/2 to 1/2 division, framed all round with a special U-profile with stop and rubber seal, with 2 external espagnolette locks, locked at the top and bottom. Rear wall with mechanical safety lock, operation at the rear on the left in the direction of travel. With swivel crossbar at the top. The door locks can be locked with a padlock. Standing platform with ladder access on both sides in the left/right direction of travel and railing for opening the door.

Condition: new, machine/vehicle number: 637ca014c140e4e48dc3231a0, empty load weight: 5,900 kg, maximum load weight: 29,100 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Patented curved front end Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Bledpfoi Rivdox Acysp Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Standing platform with step, connection plate for air/electric and brake with large clearance for optimum operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty

Condition: used, machine/vehicle number: 7e3bf6da9bda95b470a3b0a97, empty load weight: 5,340 kg, maximum load weight: 12,660 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 09/2021, tire size: 235/75 r17,5, Year of construction: 2021, Further information Chassis central axle trailer Fine-grained steel welded construction Type TPS 200 (special approval required) Front gear support leg Folding rear support Wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Spray flaps in front of each axle and anti-spray flaps behind each axle 1x spare wheel holder for 1 e-wheel, with wheel mounting kit 1x spare wheel, same make as basic tires, steel rim 1x stainless steel storage box, w=600/h=400/t=500 mm, with polished door, lockable Low loader lashing eyes 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 2 pairs of hinged lashing eyes additionally embedded in the low loading area, 10 tons each1 pair at the front and 1 pair at the rear slope Blodpfjp N Dgusx Acysp Central axle trailer towing device Tow bar with tested 50 mm towing eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Axle spacing 1810 mm (then 10 tons axle load technical) Air suspension Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake Duomatic connection at the front, with connection line to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 235/75 R17.5 Fulda brand Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin plug at the front, with connecting cable, 1 additional LED work light(s) at the rear, switched via reversing light 1x LED rotating beacon with holder, switched via parking light (removable light) Floor then with 70 mm softwood floor, steel/ checker plate flooring in the wheel housing area Rear slope with Mega Grip covering made of toothed grating Deep loading area incl. rear slope 6500 mm Front bulkhead / front corner stanchions 25 mm aluminum hollow profile, 400 mm high, pluggable Drive-on ramps Steel ramps 3600 mm long, 750 mm wide, divided via cable extension, laterally movable, Ramp displacement, minimum gap approx. 600 mm, maximum outer width approx. 2880 mm Ramp surface with Mega Grip made of toothed grating Hydraulic operation via own electro-hydraulic unit, mounted in the steel box, operation on the side in FR right . Note: Nato socket with connecting cable required on the truck. The connecting cable must not be connected while driving! Hydraulic lateral displacement of the drive-on ramps, individually controllable (only in conjunction with hydraulic ramp actuation) Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) A special permit is required for axle loads of 10,000 kg. The approval must be applied for individually in each federal state

Condition: new, machine/vehicle number: 357314e4e176f8758d11ba42b, empty load weight: 4,500 kg, maximum load weight: 30,500 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. 2 wheel chocks with holder Folding underride guard Half-shell mudguards Bodpfei Ri R Iox Acyelp Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear

Condition: new, machine/vehicle number: c1946328bb4efe26fccb128ee, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 385 / 55 r 22,5, Further information Chassis Turntable Disposal Fine-grained steel welded construction 2 longitudinal beams with cross beams, upper side of the longitudinal beams designed as container roller tracks in wear-resistant design, loadable from the rear, with ramp. For roll-off containers with 6.5/ 7.0 m. Container locking: - 2 pairs of locking hooks embedded in the floor - pneumatic actuation The container locking is a 2-point design, acting from the inside, and locking of the roll-off containers with inner web is not possible (for transporting roll-off containers with lower frame in accordance with DIN 30722) Turntable with strong ball bearing slewing ring Wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Wheels and tires 385 / 55 R 22,5 at the manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-loaded parking brake Immobilizer: the spring-loaded parking brake is activated when the container lock is open Vehicle stability system 2 non-interchangeable coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Country of registration / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar KTL black Attention: Archive pictures! Bsdpfei Ri Nmsx Acyjlp

Condition: new, machine/vehicle number: abc6276e1749f9dddc494eb32, empty load weight: 4,900 kg, maximum load weight: 30,100 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. 2 wheel chocks with holder Folding underride guard Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Bedpfxji Ri H Is Acyjlp Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear

Condition: new, machine/vehicle number: ac4e8c4b4fd368b58adf3c5d3, empty load weight: 2,860 kg, maximum load weight: 7,040 kg, overall weight: 9,900 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing Gear support foot at the front Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width (not in conjunction with forklift bracket) Quarter-shell mudguards Lockable storage space for access ramps underneath the loading area 1 pair of ramps 3,000 mm long, 360 mm wide, load capacity per pair 4,000 kg (suspension bar for ramps at the rear) Towing device for central axle trailer Towing bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension GFA or BPW axles of the manufacturer's choice, with angular roller bearings and S-cam brake Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Bljdpfx Acei Ri Eijyop Factory silver steel rims Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Hand spindle parking brake Integral air reservoir ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, with connecting cables to the motor vehicle, Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connecting cable, Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this must be retrofitted to the truck. Hydraulic connection with SVK plug NW 10/3, incl. connection hose Hydraulic actuation via truck power take-off Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and non-oscillating without central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Dropside/bridge RAL 9010 pure white Note! Bridge inside only primed if painted bridge version! Attention! These are archive pictures. Also available IMMEDIATELY with 5m bridge!

Condition: new, machine/vehicle number: 56c59c8aba35227ffb44c9f75, empty load weight: 11,350 kg, maximum load weight: 26,650 kg, overall weight: 38,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis Jumbo semi-trailer Welded steel construction with narrow cross member spacing and reinforced design, low loader external frame profile, for transporting construction machinery up to 32000 kg and up to a max. external width of the construction machinery of 2550 mm, fifth wheel plate with replaceable 2 king pins. Rear inclination to approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/checker plate, In the low bed Omega rail on the side at the bottom of the outer frame as a suspension strip for tarpaulin and spacer for the lashing points, not in the wheel area. With lift table on an additional fixed lightweight outer frame with omega profile, lift table can then be raised with closed tarpaulin! Bljdpji Riw Asfx Acyjp 24 t. 2-speed support winch, single-side operation, with semicircular lower section and straight connecting plate, with thrust compensation, free swing radius to the rear approx. 1950 mm, Folding rear support 2 wheel chocks with holder Aluminum side bumpers Quarter-shell mudguards in front of and behind each axle With anti-spray flaps behind each axle Steel underride guard Rear spray flaps across the entire width 4 stainless steel storage box, w=800/h=350/t=350 mm, with polished door, lockable 2 x in FR-left and 2 x in FR-right in front of the 1st axle Lifting table to gooseneck, approx. 3000 mm long, can be raised hydraulically for transfer to gooseneck, with mechanical locking when raised. (inclined cylinder for good ground clearance, Fliegl standard). Operation in FR-right + additional operation with radio remote control (same as ramp operation) Lifting table can be raised with closed tarpaulin! Tarpaulin suspension in the lift table area on an additional fixed lightweight outer frame with Omega profile, lift table can be raised with closed tarpaulin! Lashing mushrooms can also be used when lowered! Lashing eyes Gooseneck: 4 pairs of 5 to lashing eyes embedded in the outer frame 2 pairs of lashing points at the top and sides of the outer frameLow bed 8 pairs of lashing mushrooms at the top and sides of the outer frame, each 10 tons 9 pairs of 5to embedded in the outer frame Axles+suspension SAF drum brake axles last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lift & lower valve + auto-reset function H & S function with quick air release 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage Wheels and tires 235 / 75 R 17,5 from leading manufacturers Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection in the truck via EBS, without truck instal. (no calibrated scales) Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front, in LED 2 white/red lane departure lights at the rear, 1 rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illum

Condition: new, machine/vehicle number: d9c951d746f03c05bc5470f89, empty load weight: 5 kg, maximum load weight: 29,045 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Vario stanchion system 4 pairs embedded in loading area, can be pushed together to 2 100 mm and extended to approx. 3 500 mm for loading. Stanchions can be locked every 100 mm on an internal width of 2 100 mm to 3 000 mm, 4 pairs of divisible stanchions 600 mm + 1 200 mm, total height 1 800 mm removable. With an internal stanchion width from approx. 2 350 mm, excess width. Vario end walls Floor prepared for inserting 3 end walls. 4 x 5 pairs of Vario stanchion pockets for insertable end walls (front and rear) and 1 x 3 pairs in the middle for transporting 2 x 5,000 mm or 2 x 6,000 mm construction steel mats. 2 Vario end walls, each consisting of 1 pair of plug-in stanchions and 1 top crossbeam approx. 2200 mm wide. Cross beams can be extended by 220 mm on both sides, with lashing hole for tensioning. 1900 mm high Vario bulkhead, can be converted to 1300 mm or 700 mm high. 4 stanchion pockets embedded in the center of the floor for 80 x 80 mm stanchions 1 pair of supports at the bottom for Vario bulkhead at the front 1 pair of lower supports for rear Vario bulkhead Slightly slanted outer frame with Load-Lock profile for lashing strap attachment 14 pairs of lashing eyes additionally embedded in the outer frame, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Extension ladder at the rear Wheel chocks with holder Aluminium side collision protection Galvanized steel underride guard Quarter-shell mudguards in front of and behind axle unit Blsdpfxei Ri R De Acyjp with anti-spray flaps on last axle only Impact protection at the rear 8 construction steel winches with wire rope and counter hooks, 4 x left and 4 x right with rope feed-through through the outer frame, 1 removable slip-on gearbox for construction steel winches - supplied loose (without bracket on the frame) 1 spare wheel holder for 1 e-wheel, with wheel fastening set 1 plastic toolbox, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/h=400/420 mm/d=2460 mm 4 lashing/stanchion rails embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be to

Condition: new, machine/vehicle number: 4499ca1b286f9f653066b5693, empty load weight: 4,900 kg, maximum load weight: 27,100 kg, overall weight: 32,000 kg, axle configuration: 2 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Bljdpei Ri Niofx Acyep Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Standing platform with step, connection plate for air/electric and brake with large clearance for optimum operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Support legs coated black Body RAL 7035 light gray Fliegl StoneMaster advertising on the sides and rear Roller tarpaulin RAL on request, single color Also available with hydr. rear panel Available Therm