Used Bale Breaker for sale (982)

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Ndsdpfx Ahozp H R Esksa Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: used, Year of construction: 1989, functionality: fully functional, machine/vehicle number: 105102558/89, overall weight: 750 kg, Continuously fillable compactor with rotating roller collects, shreds, and compacts waste using a special steel roller, which ensures a compaction ratio of up to 9:1. Nedpfx Ajzr H Agohkjda It compacts the waste through alternating left/right rotation of the special roller, which continuously applies pressure to the material being fed in. It enables continuous feeding – the compacted waste remains in a transparent PE bag. The compaction station can be installed directly at the point of waste generation within the premises. It is also ideal for continuous filling via chutes or conveyor belts and is easy to operate. CE standards requires particularly little maintenance.

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: 1737/02, overall weight: 1,995 kg, This multi-chamber baling press compacts a wide variety of materials. This top-loading press is ideal for paper, plastic, metal cans, and plastic packaging. Ndsdpfx Ahjzr Hxzekoa

Condition: new, Year of construction: 2024, functionality: fully functional, machine/vehicle number: -, type of input current: three-phase, overall weight: 500 kg, Lump breaker for crushing/deagglomerating various materials. Ndodpfx Ajuvg D Eshkea

Condition: ready for operation (used), Pressing force: 60 tons DIXI press, model 60s, manufactured between 2006-2010, costs 4000 EUR. Model manufactured between 2017-2019 costs 5000 EUR. Ndedpfx Asra Nqhohkea Beam dimensions: 120 x 80 x 110 cm. Press dimensions: 1900 x 1400 x 2200 (height). Press weight: approximately 2430 kg. Beam weight: up to 500 kg. Oil heating system. Motor: 7.5 kW. New, showroom model DIXI press costs 11,000 EUR.

Condition: ready for operation (used), The DIXI 60SLD is a semi-automatic baling system with a pressing force of 60 tons, designed for the economical reduction of volume of residual materials (suitable for recycling) in industry and crafts: Cardboard boxes Foam PET bottles Insulation mats and other compressible materials. Horizontal baler, waste press DIXI 60 SLD with ejector Technical specifications: Pressing force: 60 tons, Unit pressure: 6.81 kg/cm², Power supply: 400V / 7.5kW Bale dimensions: 800x1100x1200 mm, Number of ties: 3 Bale weight: approx. 370-410 kg, Tying: manual Loading aperture: 990 x 1110 mm, Machine weight: 5420 kg Average pressing cycle: 47 seconds Year of manufacture: 2011-2016 Dixi 80SLD Baler Technical data of the Baler Brand: Dixi Model: 80 SLD Pressing force: 80 tons Drive power: 11 kW, 400 V / 32 A Infeed opening (width x height): 1040 x 1110 mm Pressing cycle: approx. 35 s Capacity: approx. 1000 kg/h Bale size (width x height x length): 1120 x 1120 x 1200 mm Ndjdpfx Ahjra A E Uokja Bale weight: Depending on the material, approx. 500–600 kg Bale tying: 3-fold, manual Machine dimensions: Length: 4200 mm (+cage 1600 mm) Width: 1830 mm Height: 2620 mm Machine weight: approx. 8000 kg Automatic bale ejection Robust construction for long-term use Year of manufacture: 2016-2020 Weight: approx. 8.4 tons Condition: Used Price: 14,000 EUR

Condition: like new (used), Year of construction: 2023, operating hours: 16 h, Cardboard or raw material press – like new For sale: a like-new raw material press for compressing cardboard. The press was originally purchased for compressing cardboard. However, after commissioning, the supplier switched to a different type of packaging, meaning the press was no longer needed. Condition: Like new Njdpfx Aezdrf Rehkoda Not used or only used minimally Ready for immediate use This is an ideal opportunity to acquire a high-quality machine in like-new condition. I have attached the original invoice in the documents below.

Condition: used, axle configuration: > 3 axles, first registration: 01/2007, color: other, Year of construction: 2007, Empty weight: 10.300 kg Axle 1: left 8 mm right 8 mm Axle 2: left 10 mm right 10 mm Axle 3: left 10 mm right 10 mm Ndodpfxozrgl Io Ahksa Axle 4 left 8 mm right 8 mm We have the possibility to stack trailers!

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, pressing force: 100 t, Technical specifications: Pressing force: 1,000 kN Specific pressing force: 121.2 N/cm² Drive power: 45 + 45 kW, frequency-controlled Voltage/Frequency: 400 V / 50 Hz Idle cycle time: 8.3 s Theoretical idle throughput: 643 m³/h Theoretical capacity at 50 kg/m³: 32.15 t/h Feed opening width x feed opening length: 970 x 1,800 mm Ndsdoygud Ajpfx Ahkea Bale width x bale height x bale length: 1,100 x 750 x 600–2,000 mm Bale weight: max. 700 kg or 800 kg, depending on material The baler feed system includes the following components: - 1 fully enclosed STADLER chain conveyor with appropriate shaft covers - 1 support and maintenance platform for conveyor and hopper - 1 STADLER conveyor - 1 automatic channel baler HSM VK8818 R FU (100 t) - 1 wire rack for 500-kg soft wire coils - 10 wire coil trolleys - 1 multi-control system for the baler - Full construction documentation and maintenance history - Serviced and maintained by the manufacturer Commissioning available upon request. Weight: 33,000 kg Tying method: wire Processable materials: plastic film, mixed paper, cardboard, hollow HDPE/LDPE containers, and plastic bottles The system is operational and can be inspected during operation. The machine will be dismantled on 16/02 and can then be inspected at our facility. Immediately available!

Condition: used, Overall dimensions: 2800x2570x2000 mm Ndedoyibhkopfx Ahksa

Condition: used, Year of construction: 2012, pressing force: 40 t, Manufacturer: HSM Ndsdpfx Ahjx H R U Sskja Model: HL 4010 Li Year of manufacture: 2012 Pressing force: 40 t

Year of construction: 2001, condition: ready for operation (used), Press force: 16t, Feed opening dimensions X/Y: 1100mm/590mm, Chamber dimensions X/Y/Z: 1100mm/700mm/1130mm, Bale dimensions X/Y/Z: 1100mm/700mm/950mm, Max. bale weight: 200kg, Tying: 4-way vertical, Throughput: approx. 4-8 bales/h, Machine dimensions X/Y/Z: approx. 1450mm/950mm/2400mm, Weight: approx. 950kg. No UVV inspection and the hydraulic oil has been drained. The baler has not been cleaned. An on-site inspection is possible. Ndjdpfx Ajzp Rhbjhkja

Condition: good (used), Strautmann AutoLoadBaler baling press Suitable for baling: Cardboard Film PET bottles Foam Cans Electronic waste Ndsdpfev Aktnex Ahksa Machine dimensions (length / width / height) mm: 2047 / 2179 / 3050 Opening approx. 1192 mm / 575 mm Bale size (length / width / height) mm: 1200 / 800 / 1100 Bale weight approx. 480 kg Pressing force kN: 530 Year of manufacture: 2017-2018

Condition: not inspected (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Ndodjic Rl Dopfx Ahkea Bale weight: approx. 500 kg Machine weight: approx. 8000kg The hydraulic unit is functional, the drive motor is in the removed state.

Condition: used, Technical data: Pressing force: 178 kN Drive power: 4 kW Work cycle time: 23 s Loading height: 928 mm Ndedpfx Ajv Akmzohkja Loading opening width x height: 1195 x 558 mm Bale length x width x height: 1200 x 780 x 1000 mm Bale weight: 250 kg Machine width x depth x height: 1700 x 1075 x 2499 mm Machine weight: 1300 kg 4-fold with polyester tape Year 2010-2013

Condition: new, Motor protection circuit breaker, series S2, 70-80A 3RV2031-4RA10 SIEMENS Ndjdozlt U Aepfx Ahkja

Condition: used, functionality: fully functional, total length: 1,000 mm, load capacity: 2,500 kg, Bale Clamp Condition: Ready for use and fully functional Technical Condition: good Description: Bale Clamp / Rotating Clamp – suitable for forklifts Lifting Capacity: 2,500 kg | Condition: good, fully operational Robust bale and rotating clamp designed for professional use in warehousing, recycling, manufacturing, and paper handling. The unit is fully functional, immediately ready for operation, and in good technical and visual condition. Technical Data: Type: Bale clamp / Rotating clamp Capacity: 2,500 kg Length: approx. 1,000 mm Opening width: as specified by device (see photos / inspection) Back width: on request Projection: on request Nodpfx Aezpb Huohkjda Dead weight: on request Condition: technically good, visually good Location: available immediately Notes: Sale as-is in current used condition. All prices are net plus 19% VAT. Sale exclusively to commercial buyers with valid VAT ID. No warranty or guarantee. Charger note does not apply to attachments, but is systemically retained.

Condition: used, functionality: unexamined, Ferwood Code: AGG0201 - Manufacturer Code: 147009FSFTI3R6 - Condition: Used - Functionality: Untested - If interested we offer a revision service, contact us. Nodsvu Uvdopfx Ahkoda

Condition: used, machine/vehicle number: 22031, Vertikale Ballenpresse / Vertical Waste Baling Press Pöttinger MP 600 ASerial-No. 5110176 Einfüllhöhe / Loading High max. 1070mm Einfüllöffnung / Filling opening 700 x 500mm Nsdpfxeiiv S Ss Ahkjda Presskasten / Pressing box 700 x 500 x 900mm Ballenformat / Bale format max. 700 x 500 x 500mm Ballengewicht / Bale weight 40 - 80Kg Anzahl Umreifungen / Vertical binding 2 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, functionality: fully functional, Year of construction: 2020, load capacity: 1,400 kg, empty load weight: 380 kg, drive type: Keine, Cellulose/Bale Clamp Njdpfx Ahey A Uadekjda Load Center: 500 mm ISO Class: ISO Class 2 = 1,000 - 2,500 kg Mast Type: None Technical Condition: Good Description: Type 1.5T413, sideshift +/- 100 mm, sideshift independent of the opening range, overall width 970 mm, opening range 495 - 1,675 mm, arm height 440 mm, arm length 1,000 mm, arms smooth on the outside, inside with round bar, arm tips beveled, load capacity 1,400 kg at 500 mm load center, installation depth 158 mm, own center of gravity at 289 mm, weight approx. 380 kg, incl. pressure gauge, connection ISO - Class 2 A.

Condition: used, functionality: fully functional, Year of construction: 2020, load capacity: 1,400 kg, empty load weight: 380 kg, drive type: Keine, Cellulose/Bale Clamp Load Center: 500 mm ISO Class: ISO Class 2 = 1,000 - 2,500 kg Mast Type: None Technical Condition: Good Description: Type 1.5T413, sideshift +/- 100 mm, sideshift independent of the opening range, overall width 970 mm, opening range 495 - 1,675 mm, arm height 440 mm, arm length 1,000 mm, arms smooth on the outside, inside with round bar, arm tips beveled, load capacity 1,400 kg at 500 mm load center, installation depth 158 mm, own center of gravity at 289 mm, weight approx. 380 kg, incl. pressure gauge, connection ISO - Class 2 A. Ndodozk Sbljpfx Ahksa

Condition: used, functionality: fully functional, Year of construction: 2020, load capacity: 1,400 kg, empty load weight: 380 kg, drive type: Keine, Cellulose/Bale Clamp Load Center: 500 mm Njdpfx Ahszbn Eijkeda ISO Class: ISO Class 2 = 1,000 - 2,500 kg Mast Type: None Technical Condition: Good Description: Type 1.5T413, sideshift +/- 100 mm, sideshift independent of the opening range, overall width 970 mm, opening range 495 - 1,675 mm, arm height 440 mm, arm length 1,000 mm, arms smooth on the outside, inside with round bar, arm tips beveled, load capacity 1,400 kg at 500 mm load center, installation depth 158 mm, own center of gravity at 289 mm, weight approx. 380 kg, incl. pressure gauge, connection ISO - Class 2 A.

Condition: ready for operation (used), Two Temafa bale opener lines are offered for bale opening, pneumatic conveying of fiber bales and processing of natural and synthetic fibers. 1. Bale opener: 1) Bale opener BÖ-KSP 0347, working width: 1600mm. 2) Rod conveyor table FTRY 0502, length: 5700mm, width: 1600mm. 3) Material extraction hopper, working width: 1600mm, pipe flange: 350mm. 4) AEG extraction fan, type: AM 160 MR 4, power: 11kW, speed: 1450rpm. 2. Bale opener: 1) Bale opener BÖ-KSP with Cleanmaster, working width: 1300mm. 2) Rod conveyor table, length: 5000mm, width: 1260mm. 3) Material diverter for feeding into the CMA or for direct discharge. 4) Cleanmaster (CMA) with infeed, tumbler and time-controlled discharge flap. 5) TV 300 extraction fan and auxiliary extraction fan for cleaning the CMA and for wool room extraction. 6) Control cabinet, year of manufacture: 1999, control system: Siemens S5 with Lauer terminal. Documentation available. The machines are available from April 2027. The machines can be purchased separately. An on-site inspection is possible. Nedpfx Ahoznx Nkskeda

Condition: good (used), Year of construction: 2014, operating hours: 7,145 h, functionality: fully functional, Channel Bale Press Presto HPK 50 HS, Year of Manufacture: 2014 Nedpjzk Drvofx Ahkoda Manufacturer: Presto Model: HPK 50 HS Year: 2014 Drive Power: 30 kW Pressing Force: 50 t Operating Hours: 7,145 Feed Opening: 1600 x 650 mm (LxW) Channel Cross-Section: 700 x 950 mm Max. Filling Volume: 1.06 m³ Cycle Time: 20 s Tying: 4-fold Throughput Performance at 35 kg/m³: 5.5 t/h 60 kg/m³: 8.8 t/h 100 kg/m³: 12.7 t/h Bale Weight: up to 500 kg Machine Dimensions: 8420 x 1900 x 2400 mm (LxWxH) Machine Weight: approx. 10,500 kg Materials: Paper, Cardboard, Film, PET bottles Note: All knives and counter-knives as well as all sliding plastics have been replaced. The press is in good condition and has been checked and tested. A video is available on our website or YouTube channel. The operating manual and CE declaration are included. Please note: All technical data is based on information provided by the manufacturer. We do not assume liability for the information provided or for possible errors. This offer is subject to change, prior sale, and can be revoked at any time. Inspections are possible by prior arrangement. Sale is made against advance payment, ex works, without warranty or guarantee.

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Vertical baling press Dixi 50 S, year of manufacture 2019, in very good condition Technical data Manufacturer: Maschinenfabrik Bermatingen Type: Dixi 50 S Year of manufacture: 2019 Drive power: 7.5 kW Pressing force: 50 t Pressing time: 23 s Feed opening: 1200 x 620 mm Feed height: 1000 mm Bale size: 1200 x 800 x 830 mm Bale weight: 300-350 kg Tying: manual Transport dimensions: 1600 x 1300 x 2200 mm Weight: 2300 kg Materials: PET bottles, HDPE/LDPE/PP, hollow containers, big bags, textiles, film, polystyrene, non-woven fabric, glass wool, etc. Note: The machine is in very good condition. It has been inspected and tested by us in 28816 Stuhr. The video can be found on our website or our YouTube channel. The operating manual and EC declaration of conformity are available in German. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any errors. The offers are subject to change, sale is subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. Nodpszk Dqfsfx Ahkjda The sale takes place ex works, without warranty.