Universal machining center

MATSUURA MAM72-25V PC2

Condition: ready for operation (used), Year of construction: 2007, operating hours: 66,963 h, functionality: fully functional, travel distance X-axis: 550 mm, travel distance Y-axis: 410 mm, travel distance Z-axis: 450 mm, table load: 40 kg, rotational speed (max.): 15,000 rpm, TECHNICAL DETAILS B-axis: +110° to -110° C-axis: 360° Table indexing B and C axes: 0.001° Dksdowx Iugspfx Aiwsl Workpiece Max. workpiece size: Ø 250 × height 250 mm Max. table load: 40 kg Pallet System Pallet size: Ø 130 mm Max. workpiece size on pallet: Ø 250 × height 250 mm Max. pallet load: 40 kg Pallet interface: Capto C6 Spindle Standard speed range: 50 - 15,000 rpm Spindle taper: BT40 JIS B 6339 Big+ Spindle motor power with FANUC drive: 7.5 / 5.5 kW Max. torque: 65.1 Nm at 1,100 rpm Rapid Traverse and Feed Rates Rapid traverse X, Y, Z axes: 50,000 mm/min Rapid traverse B-axis: 30 rpm Rapid traverse C-axis: 50 rpm Feed rate X, Y, Z axes: 1…50,000 mm/min Feed rate B-axis: 30 rpm Feed rate C-axis: 50 rpm Tool Changer Max. tool weight: 10 kg Max. tool diameter (all stations occupied): Ø96 mm Max. tool diameter (with adjacent stations empty): Ø150 mm Max. tool length: 300 mm Guideways Axis guideways: Roller guides Lubrication: Permanent grease lubrication Ball screws X, Y, Z axes Ø: 36 mm Pitch: 16 mm Axis Drives Motor rating X, Y, Z axes: 4.5 / 4.5 / 5.5 kW Motor rating B, C axes: 4.5 / 2.5 kW Axial force X, Y, Z axes: kN (value not specified) MACHINE DETAILS Control: MATSUURA G-Tech 30i (FANUC 30i MA) Serial number: SN17224 Weight & Dimensions Standard machine weight: 7,800 kg Machine with PC-2: 8,600 kg Machine height above floor: 2,705 mm Width: 2,281 mm Depth: 3,665 mm Electrical Connections Total connected load (standard machine): 32 kVA Supply voltage: 3 x 400 V, 50 Hz Compressed air connection: 5.5-9.5 bar EQUIPMENT 5-axis simultaneous control Expanded tool magazine capacity to 40 tool stations Pallet changer with 2 pallets, 130 mm diameter Direct path measuring system (Heidenhain) in X, Y, and Z axes, pressurized with sealing air KNOLL coolant system: 1 scraper or hinge belt chip conveyor with lift pump and chip discharge to operator side (Type: 500 K-1/10, year of manufacture 2010) 1 through-spindle coolant supply with KTS25-50T coolant pump, capacity 31 l/min at 70 bar, 5.5 kW, three-stage adjustable pressure 1 external coolant with coolant pump, capacity 100 l/min at 1.4 bar 1 coolant flush with coolant pump, capacity 100 l/min at 1.4 bar 1 compact filter KF200, filtration capacity 200 l/min 2 auger-type conveyors in the machine RENISHAW OMP 60 probing system for automatic workpiece zero-point setting and measurement, can be changed via tool changer OMRON pressure transducer for tool length measurement and tool breakage monitoring

Condition: refurbished (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: SL154SY, turning length: 750 mm, turning diameter over cross slide: 510 mm, turning diameter: 680 mm, spindle motor power: 7,500 W, spindle speed (min.): 50 rpm, spindle speed (max.): 5,000 rpm, spindle bore: 56 mm, travel distance X-axis: 215 mm, travel distance Y-axis: 70 mm, travel distance Z-axis: 550 mm, mount diameter: 20 mm, rapid traverse X-axis: 18,000 m/min, rapid traverse Y-axis: 6,000 m/min, rapid traverse Z-axis: 24,000 m/min, rotational speed (max.): 3,000 rpm, rotational speed (min.): 20 rpm, type of input current: three-phase, feed length X-axis: 215 mm, feed length Y-axis: 70 mm, feed length Z-axis: 550 mm, torque: 70 Nm, bar passage: 56 mm, total height: 2,015 mm, total length: 3,336 mm, total width: 1,873 mm, Equipment: rotational speed infinitely variable, MORI SEIKI SL154SY LATHE WITH LNS BAR FEEDER Dkodpfx Ajxddfvjiwol RENISHAW LASER CHECKED TOOLBOX. MACHINE INSPECTED AND READY TO WORK IN OPTIMAL CONDITIONS.

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, The positions of the rotating tools are: T01-02-03-04 / T22-23 / T34-35 - equipped with Iemca Boss 332E/32 new in 2006 - lot of collets / guide bushes - MSC-501 Control - the machine has always worked with oil. Dodpfx Aowpu Etjiwokl

Year of construction: 2012, condition: excellent (used), *PROMOTIONAL PRICE!!! Machine has Japanese Kitagawa rotary tilting table Fanuc 0I-MD control system BT30 spindle 12 tool capacity Dkodei Dbc Ujpfx Aiwsl We have 2 sets in our stock.

Condition: excellent (used), Year of construction: 2016, operating hours: 8,100 h, functionality: fully functional, machine/vehicle number: 2066-5172, Equipment: documentation/manual, CNC Tool Grinder WALTER HELITRONIC ESSENTIAL – year of manufacture 2016 For sale: 5-axis CNC tool grinder from the renowned manufacturer Walter Maschinenbau GmbH. The machine is designed for precision machining of cutting tools such as end mills, drills, as well as special and multi-flute tools. The unit is fully operational, regularly serviced, and maintained in excellent technical condition. BASIC DATA Model: WALTER HELITRONIC ESSENTIAL Year of manufacture: 2016 Control system: FANUC Number of axes: 5 Operating hours: 8,100 h Power supply: 3 x 400 V AC, 50/60 Hz Connected load: 25 kVA TECHNICAL SPECIFICATIONS Travel distances: X = 330 mm Y = 213 mm Z = 475 mm Rapid traverse speeds X, Y, Z: 15 m/min A axis: 360° C axis: ±200° Spindle speed: 10,500 rpm Spindle motor power: 9 kW Spindle diameter: 70 mm Maximum grinding wheel diameter: 150 mm Maximum workpiece length (peripheral wheel grinding): 255 mm Maximum workpiece length (face wheel grinding): 185 mm Maximum grinding diameter (complete machining): 100 mm Minimum working pressure: 6 bar Dedpfxjyz Dwco Aiwokl Air consumption: 8,000 l/h Coolant pump capacity: 80 l/min at 7 bar Coolant tank capacity: 350 l Machine weight: 3,300 kg Software: Tool Studio version 2.1 EQUIPMENT AND FEATURES Automatic loading arm The machine is equipped with an automatic tool loading system. The arm picks up tools from the input tray, transfers them for machining, and then places finished tools onto the output tray. This enables fully automated, uninterrupted production without constant operator supervision. Capability for mounting two grinding wheels Simultaneous mounting of two grinding wheels increases operational flexibility, reduces changeover times, and makes it possible to perform more complex operations without frequent wheel exchanges. Cooling for electrical cabinet HAOSCH cooling unit included. Additional equipment Professional measuring device for end mills and drills, providing fast, precise, and repeatable measurements to facilitate tool setup before machining. TECHNICAL CONDITION The machine is in very good technical condition Operated in clean production environment Fully enclosed work area for safety and noise reduction Regularly serviced.

Condition: ready for operation (used), Year of construction: 2009, operating hours: 9,192 h, travel distance X-axis: 1,200 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 500 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, spindle speed (max.): 16,000 rpm, number of axes: 3, This 3-axis HERMLE C 1200 vertical machining centre was manufactured in 2009. It features an impressive X-axis travel of 1200 mm, Y-axis travel of 900 mm, and Z-axis travel of 500 mm. The machine is equipped with a spindle speed of 16,000 rpm and includes 30 tool stations. If you are looking to get high-quality machining capabilities, consider the HERMLE C 1200 machine we have for sale. Contact us for further details. • X – 1200 mm • Y – 900 mm • Z – 500 mm • Machining Center C 1200 V • Heidenhain iTNC 530 contouring control • Spindle 16,000 rpm • SK 40 • 30 Tool Stations • Rigid Clamping Table • Coolant System • Electronic thermal compensation (iTNC) with temperature sensors on the motor spindle and machine base • Portal design with a closed rear wall for significantly better support during torsional loads • Two axes are located in the tool, providing very good mass distribution and ideal conditions for high rapid traverse and feed rates • Feed screw diameter and pitch (X and Z axes): 40 / 20 mm • Feed screw diameter and pitch (Y axis): 50 / 20 mm • Direct measuring system • Resolution: 0.0001 mm • Position tolerance (Tp) in X-Y-Z axes according to VDI/DGQ 3441: 0.010 mm • Recommended ambient temperature for maintaining accuracy: 20 °C ± 1 °C Djdjylw Stepfx Aiwokl • Flushing/wash-down system for rinsing the side work area • Display: 15" TFT color flat screen • Flexible contour programming • Part program memory • Tool diameter capacity: 80 mm • Tool diameter with free adjacent slots: 125 mm • Maximum tool length: 300 mm • Maximum tool weight: 8 kg • Maximum magazine load: 120 kg • Chip-to-chip tool change time according to VDI 2852: 6.5 seconds • Manual control unit includes electronic handwheel, axis direction keys, feed control, rapid traverse, emergency stop, and enable switch • Machine on – 11,927 h • Spindle on – 9,192 h Additional equipment • Chip conveyor • Heidenhain touch probe • Electronic Manual Control Module (iTNC) Technical Specification Taper Size SK 40

Condition: used, Year of construction: 2007, Fanuc Robodrill Alpha T21iEL 5-axis machine Year of manufacture: 2007 Control: Fanuc 31i Manual Guide Axis travels: -X: 700 mm -Y: 400 mm -Z: 330 mm -C: 360 degrees -B axis 4th and 5th axis: Tsudakoma TN130 rotary table Spindle: max. 24,000 rpm Spindle taper: BT30 Dkodpfx Aieyg Hl Ejwol Tool magazine: 21 positions -documentation -coolant tank with pump

Condition: like new (used), Year of construction: 2010, Haas Multigrind CB multi axis CNC grinder, 12 station, Siemens Sinumerik 840D control, load / unload, LTA industrial air cleaning unit, Dkodpfx Aiov Igg Iewjl (2010) Technical Data - Grinding Spindles (With Two spindle ends) Interface - Cone ø 31.75mm Performance 100% / 40 % ED - 11.5 / 14.5kW Standard rotation speed - 8,000rpm Option: One spindle end Interface - HSK 50E Performance - 100% / 40% ED - 11.5/ 14.5 kW Standard rotation speed - 8,000rpm Option: One spindle end Interface - HSK 50E Performance 100% / 40% ED - 11 / 12 kW Standard rotation speed - 18,000rpm Option: One spindle end Interface - HSK 80E Performance 100% / 40% ED - 30/30 kW Standard rotation speed - 8,000 rpm Option: High Frequency spindle - On request Machine Table Clamping surface - 1000 x 500mm Number, distance and width of the T slots - 9 / 50 / 12H7mm Work Range X- Axis - 700mm (optional) 1000mm (optional) 1200mm Y Axis - 410mm Z Axis - 500mm C Axis angle of rotation - 320° Option: X3 - auxilliary axis Work range - 400mm Probing system and feed Resolution of linear axes - 0.0005mm Rapid feed of linear axes - 30,000mm/min Resolution of rotary axes - 0.001° Rotation speed of C Axis - 400rpm Rotary axis ( A axis) Standard tip height - 175mm Rotation speed as spindle - 2600rpm Standard interface - ISO SK 50 / centering 70H5 Optional - HSK 100 / 80 / 63 / 50 Tool Changer option HSK50E Number of tools / Diameter of tools Inner wheel - 5 / 300mm to 9 / 100mm Outer wheel - 7 / 300mm to 16 / 100mm HSK80E Number of tools / Diameter of tools Inner wheel - 5 / 300mm to 8 / 100mm Outer wheel - 7 / 300mm to 14 / 100mm Workpiece size Diameter 340mm Length 550mm Length between tips 500mm Electrical supply Operating voltage 400V / 50Hz fused to 80 A Controller Siemens contouring control - Sinumerik 840 DSL Pneumatics Operating pressure - 6 - 10bar Weight Total weight depending on equipment 10,000kg or more Floor space requirement Length x width (standard) 3227 x 2700mm Height during operation 3550mm Height with option of coolant nozzles 3810mm (min hall height 4100mm)

Condition: good (used), Year of construction: 1994, functionality: fully functional, feed length X-axis: 1,050 mm, feed length Y-axis: 360 mm, feed length Z-axis: 500 mm, travel distance X-axis: 1,050 mm, travel distance Y-axis: 360 mm, travel distance Z-axis: 500 mm, overall weight: 3,000 kg, Equipment: documentation/manual, Tiger FO 135 universal milling machine Description of the machine The machine was purchased new in 1994 and has only been in operation for a few hours. The milling machine is fully functional. The axis movements are smooth and the guides are in good condition. good condition. These have an automatic lubrication system. The table is in good condition and shows hardly any signs of wear. The machine also has a digital readout for the 3 axes, which makes it possible to work with cutter compensation and recurring measurement machining. Operating instructions are included with both the machine and the digital indicator. Technical specifications - Table dimensions 1,400 x 340 mm, 4 T-slots - Automatic traverse path: ➢ Longitudinal X 1,050 mm ➢ Transverse Y 360 mm ➢ Vertical Z 500 mm - Fixing the spindle cone: ➢ Vertical axis ISO 40, automatic locking ➢ Horizontal axis ISO 40, manual locking - Spindle speed range: ➢ Vertical axis 33 ÷ 1,560 rpm, 12 speeds ➢ Horizontal axis 35 ÷ 1,550 rpm, 12 speeds - Installed power: ➢ 5 kW vertical spindle motor ➢ 7.5 kW horizontal spindle motor ➢ Direct current motor 15 Nm - Variable power supplies Continuous speed 0 ÷ 1,500 mm/min - Fast feed ➢ Lengthwise and crosswise 3,000 mm/min Vertical 1,500 mm/min - Universal head with manual shaft lowering of 80 mm - Automatic lubrication with pump - Low-voltage electrical controls on the pushbutton panel of the side arm - Star/delta start - Magnetic thermal protection from Siemens - Net weight 3,000 kg - Machine dimensions (for transportation) ➢ Width 2,300 mm ➢ Depth 2,900 mm ➢ Height 2,400 mm Accessories - Counter supports for cutting shaft - Cutting shaft ø32 mm Tiger FO 135 universal milling machine Description The machine was purchased new in 1994 and has only had a few hours of operation. The milling machine is fully functional. Axis movements are smooth and the guides are in good condition. These have an automatic lubrication system. The table is in good condition and shows hardly any signs of wear. The machine also has a DRO for the 3 axes, which offers the possibility of working with milling compensation and recurring measurement processing. Both the machine and the DRO come with operating instructions. Technical specifications - Table dimensions 1,400 x 340 mm, 4 T-slots - Automatic travel: ➢ Longitudinal X 1,050 mm ➢ Transverse Y 360 mm ➢ Vertical Z 500 mm - Fixing the spindle cone: ➢ Vertical axis ISO 40, automatic locking ➢ Horizontal axis ISO 40, manual locking - Spindle speed range: ➢ Vertical axis 33 ÷ 1,560 rpm, 12 speeds Horizontal axis 35 ÷ 1,550 rpm, 12 speeds - Installed services: ➢ 5 kW vertical spindle motor ➢ 7.5 kW horizontal spindle motor ➢ DC motor 15 Nm - Variable power supplies Dsdpfx Aerqwbijiwjkl Continuous speed 0 ÷ 1,500 mm/min - Fast forward ➢ Longitudinal and transverse 3,000 mm/min ➢ vertical 1,500 mm/min - Universal head with manual shaft lowering of 80 mm - Automatic lubrication with pump - Low voltage electrical controls on side arm push button panel - Star/delta start - Magnetic thermal protection from Siemens - Net weight 3,000 kg - Dimensions of the machine (for transport) Width 2,300 mm ➢ Depth 2,900 mm ➢ Height 2,400 mm Accesories - Counter supports for cutting shaft - Cutting shaft ø32 mm

Condition: used, Year of construction: 2011, operating hours: 26,920 h, IRB 6640-235/2.55 Construction year 2011 Dsdpeim Si Asfx Aiwjkl We can offer you this robot overhauled too!