Used horizontal machining centers for sale (486)

Condition: used, Year of construction: 1996, functionality: limited functionality, travel distance X-axis: 630 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 650 mm, controller model: Fanuc MSX-516, rotational speed (max.): 12,000 rpm, The P8 power supply, valued at €1,500, was only replaced in August 2024! The spindle was repaired in 2017 and has mostly only been used for single-layer operation since then! TECHNICAL DETAILS Travel range X-axis: 630 mm Travel range Y-axis: 600 mm Travel range Z-axis: 650 mm Pgsdpszcuyiofx Aahon Feed length X-axis: 630 mm Feed length Y-axis: 600 mm Feed length Z-axis: 650 mm Table width: 500 mm Table length: 500 mm Number of pallets: 2 Maximum speed: 12,000 rpm Number of tool magazine slots: 60 (BT40) MACHINE DETAILS Control: Fanuc MSX-516 Phases: 3 Frequency: 50 Hz Voltage: AC 200 V Full load current: 181 A Note: The rapid traverse rate of the X-axis is reduced by 20% to extend the service life of the telescopic guides. The sealing ring during pallet changes is likely defective. The seller temporarily resolved this by inserting a ball valve in between when the pallets needed to be changed. EQUIPMENT Documentation/Manual Chip conveyor

Condition: ready for operation (used), Year of construction: 2005, operating hours: 44,673 h, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 900 mm, controller model: OSP-E100M, spindle speed (max.): 12,000 rpm, number of slots in tool magazine: 320, No minimum price – guaranteed sale to the highest bidder! Submitting a bid commits you to collecting the machine on time in week 30 of 2026! TECHNICAL DETAILS Travel range X-axis: 1,000 mm Travel range Y-axis: 900 mm Travel range Z-axis: 900 mm Spindle speed: 12,000 rpm Tool holder: BT50 Tool positions: 320 Tool positions for 600 mm tools: 80 Part accuracy: 0.001° MACHINE DETAILS Control system: OSP-E100M Number of axes: 4 Coolant pressure: 30 bar Dimensions & Weight Machine: 4800 x 2980 x 3150 – 21.5 t Tool magazine: 4500 x 2800 x 3150 - 6–7 t Chip conveyor: 4500 x 1600 x 2400 – 2 t, including high-pressure pump Pgjdjzd Tapopfx Aahen Repo: 3000 x 1200 x 1500 mm, 0–0.5 t Operating hours NC cycle time: 71,235 h Spindle running time: 56,241 h Machining time: 44,673 h EQUIPMENT ATC with 320 positions 80 positions for 600 mm tools 2 pallets Balluff writing/reading system NC table Absolute scales in X, Y and Z Renishaw MP10 measuring probe Tool breakage monitoring MOP tool monitoring 30-bar coolant system Mayfran Consep 2000 chip conveyor

Condition: ready for operation (used), Year of construction: 2005, operating hours: 10,197 h, functionality: fully functional, travel distance X-axis: 1,300 mm, travel distance Y-axis: 710 mm, travel distance Z-axis: 710 mm, controller model: Fanuc 18i-MB, spindle speed (max.): 10,000 rpm, TECHNICAL DETAILS Number of axes: 4 Travel in X-axis: 1,300 mm Travel in Y-axis: 710 mm Travel in Z-axis: 710 mm Pgjdpszdfgpefx Aahsn B-axis rotation: 360° Table length: 1,500 mm Table width: 660 mm Tool holder: ISO40 Max. spindle speed: 10,000 rpm MACHINE DETAILS Control system: Fanuc 18i-MB Power: 38.4 kW Dimensions & Weight Dimensions (L x W x H): 4,300 x 3,250 x 3,080 mm Shipping weight: 7,000 kg Shipping packages: 4 Operating hours: 10,197 h EQUIPMENT External coolant system Chip conveyor Tool magazine with 32 positions CE marking

Condition: ready for operation (used), operating hours: 41,072 h, functionality: fully functional, travel distance X-axis: 630 mm, travel distance Y-axis: 560 mm, travel distance Z-axis: 560 mm, spindle speed (max.): 12,000 rpm, number of slots in tool magazine: 20, TECHNICAL DETAILS Psdpozd Aw Dofx Aahogn Travel in X-axis: 630 mm Travel in Y-axis: 560 mm Travel in Z-axis: 560 mm Spindle speed: 12,000 rpm Feed rate: 20-10,000 mm/min Rapid traverse rate X/Y/Z: 26/26/20 m/min Number of positions in tool changer: 20 Spindle mount: SK 40 Table surface area (L x W): 1,000 x 600 mm MACHINE DETAILS Control system model: Heidenhain TNC 430 Total power consumption: 26 kW Operating hours: 41,072 h Machine weight: approx. 6.5 t EQUIPMENT B-axis (NC milling head) Electric handwheel Chip conveyor Cooling system

Condition: ready for operation (used), Year of construction: 2003, operating hours: 28,877 h, functionality: fully functional, machine/vehicle number: NH501CD0388, travel distance X-axis: 650 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 730 mm, controller model: Fanuc MGS-501, rotational speed (max.): 8,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 650 mm Travel range, Y-axis: 600 mm Travel range, Z-axis: 730 mm Rapid traverse rate, X-axis: 50 m/min Rapid traverse rate, Y-axis: 50 m/min Rapid traverse rate, Z-axis: 50 m/min Maximum workpiece height: 900 mm Maximum workpiece diameter: 730 mm Maximum workpiece weight: 500 kg Table dimensions: 500 x 500 mm Table load capacity: 500 kg Maximum spindle speed: 8,000 rpm Distance from table center to spindle nose: 100 mm Number of spindles: 1 Torque: 302 Nm Number of tool positions in the tool magazine: 60 Tool length: 500 mm Tool diameter: 120 mm Tool weight: 30 g Tool holder type for turret 1: ISO 50 MACHINE DETAILS Control system: Fanuc MGS-501 Rated apparent power: 73 kVA Input voltage: 380 V Type of input current: Three-phase Dimensions & Weight Dimensions (L x W x H): 4,900 x 2,595 x 2,770 mm Total weight: 13,200 kg Operating hours (according to diagram): 28,877 h Power-on time (according to diagram): 94,850 h EQUIPMENT Pedpfszcla Hsx Aahegn CE marking Documentation/Manual Spindle speed infinitely adjustable Chip conveyor

Condition: ready for operation (used), Year of construction: 2008, operating hours: 1,752 h, functionality: fully functional, machine/vehicle number: 2052592, travel distance X-axis: 1,626 mm, travel distance Y-axis: 1,270 mm, travel distance Z-axis: 813 mm, table load: 4,536 kg, spindle speed (max.): 6,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range X-axis: 1,626 mm Travel range Y-axis: 1,270 mm Travel range Z-axis: 813 mm Table length: 1,626 mm Table width: 914 mm Table load: max. 4,536 kg Spindle speed: 6,000 rpm Drive system: geared head Torque: max. 610 Nm at 500 rpm Power: max. 22.4 kW Thrust force X/Y axis: max. 24,910 N Thrust force Z axis: max. 33,362 N Rapid traverse: max. 13.7 m/min Cutting feed rate: max. 12.7 m/min Tool diameter with full tooling: max. 102 mm Tool diameter with free adjacent positions: max. 254 mm Tool-to-tool time: 10.3 s Chip-to-chip time: 12.6 s MACHINE DETAILS Dimensions (L x W x H): 3,660 x 3,880 x 3,190 mm Pgedpfx Aaozd Tcdehjn Operating hours (see image) Spindle hours: 1,752 h Servo hours: 15,789 h

Condition: excellent (used), Year of construction: 2007, BA 600-2 CNC, Horizontal Milling and Drilling Center SW Schwäbische Werkzeugmaschinen GmbH Travel: X axis: 600 mm Y axis (changeover position): 600 (975) mm Z axis: 500 mm Control: Siemens 840D control, side-mounted Feed/Rapid traverse speeds: X, Y, Z: 1 – 45,000 mm/min Max. feed force X, Y, Z: 15,000 N Average acceleration: X, Y, Z: 2.5 m/s² Measuring system: Direct measuring system X, Y, Z Spindles: Spindle speed (infinitely variable): 20–10,000 rpm Torque: 2 x 363 Nm (S6/40% duty cycle) Power: 2 x 38 kW (S6/40% duty cycle) HSK-A 100, horizontal tandem arrangement Spindle distance: 600 mm Spindle bearing diameter: 100 mm Motor spindles, liquid-cooled, AC technology Working area: Swing carrier with spur gearing, max. workpiece weight 2,000 kg Pgodpfx Ajzhlfrjahjn Swivel time 0/180 degrees approx. 6.0 sec 2 NC rotary tables, hydraulically clamped, max. workpiece weight 700 kg, table speed 25 rpm Partition between machining and loading area Tool magazine: 2 x 50 tools HSK-A 100 chain-type magazine Tool change time (chip-to-chip): 4.48 sec Max. tool diameter: 100 mm 250 mm with adjacent slot free Max. tool length: 420 mm Max. tool weight: 20 kg Equipment: Central lubrication Oil minimum quantity lubrication (spindle lubrication) Chip conveyor (hinged belt conveyor) Coolant purification with compact band filter Hydraulic unit Maintenance unit Water recooler Full enclosure, crane loading possible Dimensions: approx. 5.15 x 8.50 x 4.20 m Weight: approx. 20,000 kg Year of manufacture: 2007 Other features: Very good condition Setup parallel to main time Available from December 2023/January 2024

Condition: used, Year of construction: 2005, x-travel 800 mm Pgjdpfxezhch Ds Aahsn y-travel 800 mm z-travel 800 mm Control Siemens 840D total power requirement --- kW weight of the machine ca. --- t dimensions of the machine ca. --- m

Condition: used, Year of construction: 2012, operating hours: 35,000 h, machine/vehicle number: MU44-16201032ELCS, Travel ranges (X/Y/Z): 800/700/510 mm, with NC rotary table, max. spindle speed: 12,000 rpm, 48-tool changer, WinMax control system, chip conveyor, coolant system. Pgodpfxozha Eyo Aahsn

Condition: used, Year of construction: 2019, operating hours: 2,117 h, machine/vehicle number: 20190908, Travel ranges (X/Y/Z): 1 mm, table size: 1,200 x 600 mm, spindle speed: 12,000 rpm, 40-position tool changer, tool holder SK 40, control system HEIDENHAIN TNC 640, machine weight: 7,800 kg, 3D measuring head, chip conveyor, paper band filter system, chip container. Pgedezha E Tspfx Aahon

Condition: used, Year of construction: 2019, operating hours: 16,785 h, machine/vehicle number: 20200108, Travel ranges (X/Y/Z): 650/750/500 mm, max. spindle speed: 18,000 rpm, with NC rotary table, 60-position tool changer, tool holder HSK63A, control system HEIDENHAIN TNC 640, chip conveyor, band filter system, cooling system, machine weight: 13,000 kg. Psdpfx Aajzha Hdohegn

Condition: used, Year of construction: 2010, operating hours: 38,353 h, machine/vehicle number: MC54G-16201060AKA, Travel ranges (X/Y/Z): 3,200/2,100/920 mm, max. spindle speed: 6,000 rpm, tool holder: SK50, chip conveyor, control system: HURCO Winmax, 40-position tool changer, cooling unit: HABOR, coolant: R407C. Pjdpjzha Etefx Aahegn

Condition: used, Year of construction: 2019, operating hours: 14,857 h, machine/vehicle number: 150015, Travel ranges (X/Y/Z): 1,500 x 750 x 900 mm, 38-position tool changer, SK40, weight: 8,720 kg, control system: HEIDENHAIN TNC 640, 1 chip conveyor, 1 set of SK40 tool holders, approx. 60 pieces, on a transport cart. Pgedpfx Aajzha Afshen

Condition: used, Year of construction: 2022, machine/vehicle number: YAA7159, Travel ranges (X/Y/Z): 600/400/500 mm, with a double pallet table, spindle speed: 12,000 rpm, machine weight: 6,600 kg, chip conveyor, band filter system, MITSUBISHI ELECTRIC M80 control system, HABOR cooling system, 30-position tool changer. Pgedezhaxyepfx Aahjn

Condition: ready for operation (used), Year of construction: 1997, - USED - 4-AXIS HORIZONTAL MACHINING CENTRE WITH PALLET CHANGER X-AXIS TRAVEL: 1500 mm Y-AXIS TRAVEL: 1200 mm Z-AXIS TRAVEL: 1250 mm SPINDLE: 10-4000 rpm; 40 kW; HSK-A 100 PALLET: CONTINUOUS ; 1000X1000 mm; 1-500 rpm MAX ADMITTED LOAD: 2000 Kg TOOL MAGAZINE: CHAIN-TYPE ; 161 POS CONTROL UNIT: SIEMENS 840 C Pgedeh Hfrnepfx Aahjn OVERALL DIMENSIONS: 8500 x 4800 x 4800 mm ACCESSORIES: SWARF CONVEYOR ; PAPER FILTER NOTE: COMPLETELY OVERHAULED MACHINE; HORIZONTAL AND VERTICAL AUTOMATIC HEAD; TURNING TABLE

Condition: used, Year of construction: 2016, Makino A51NX in very good condition, including a new ATC tool changer and Cubes. Approx. 11,000 hours of cutting time. Capacity & Travels: Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Workpiece: ∅ 630 mm × 900 mm Max. Payload Capacity: 400 kg Spindle: Spindle Speed: 15,000 RPM Pjdpfx Aajzg N E Hshjgn Spindle Taper: HSK-A63 Motion & Feed Rates: Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cutting Feedrate: 50,000 mm/min Axis Acceleration: 1G B-Axis Indexing: Full 4th axis, Direct Drive (0.001-degree increments) Tooling: ATC (Automatic Tool Changer) Capacity: 60 tools Tool-to-Tool Time: 0.9 seconds Max. Tool Diameter / Weight: 170 mm / 12 kg 04003 HSK-A63 Spindle – Replaces the standard ISO50 interface. Features a double taper, full face contact, and hollow shank interface. Tool clamping force is higher than 44kN; HSK tool holders are required. 14017 HSK holders for 60 Tool ATC 26001 Moire Scale Feedback X, Y, Z-Axis Increments 0.05µm, positioning tolerance Tp = 0.006mm (ISO 230-2). 29006 Through Spindle Coolant 3.0MPa – Provides TSC flow of 30 l/min at 3.0MPa, replacing the standard 1.5MPa. Air through the spindle is possible. The pressure data refers to the output flange of the pump. 29009 Flow Switch for Through Spindle Coolant – Monitors through-spindle coolant flow. The machine will feed hold if the flow is below a preset level. Note: Recommended option for filtration systems to prevent tool damage. 31002 Air curtain for splash guard window – Located in the middle of the operator-side window, this air curtain prevents chips and coolant from obstructing the view. 37000 Broken tool sensor outside machining area (BTS) – Tool breakage detection for centric tools (tool diameter 1-40mm, tool length 65 - 430mm). Length measurement is performed using a movable probe. The measurement takes place in the ready position for a tool change, outside the machining area. Accuracy ± 2mm. If there is a difference between the measurement before and after machining, an alarm is triggered automatically. 37101L Automatic Workpiece Measuring Device (RENISHAW OMP60) – Three-coordinate measuring probe from RENISHAW with automatic coordinate correction. The signal is transmitted via infrared. Tolerance approx. 0.005mm. 14 automatic measurement cycles are available as pre-programmed cycles in the program memory. Note: requires 13m. Control Options: 60001 Automatic Corner Override (G62) – Automatically decelerates the cutter at a corner depending on the corner angle, in order to maintain the cutting rate per unit time. 62007 Run hour and parts quantity display. 63034 DATA CENTER Storage Type B (total: 800MB) – Communication card with internal 800MB removable flash RAM card used for storing and executing NC data (of subprograms) for high-speed, high-definition finishing and supporting SGI capabilities. CNC programs can be transferred to and from a CAD/CAM system from the operator's pendant by FTP get and put commands over an Ethernet cable. 66003 Additional 48 Work Offsets (G54.1 P1-P48) – Allows for 48 work coordinate systems, simplifying multiple part fixtures. 68010 600 Macro Common Variables – Variable numbers 100-199 are reset and cleared when the power is turned off, while 500-999 are permanent. Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Payload Capacity: 400 kg Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cut...

Condition: ready for operation (used), Year of construction: 1998, travel distance X-axis: 3,000 mm, travel distance Y-axis: 2,500 mm, travel distance Z-axis: 1,500 mm, table load: 20,000 kg, spindle speed (max.): 3,500 rpm, number of axes: 3, This 4-axis Burkhardt-Weber MC100 was manufactured in 1998. It features a working range with an X-axis travel of 3,000 mm, Y-axis travel of 2,500 mm, and Z-axis travel of 1,500 mm. The machine has a maximum table load capacity of 20,000 kg and a spindle speed of 3,500 RPM. If you are looking to get high-quality milling capabilities, consider the Burkhardt-Weber MC100 horizontal machining centre we have for sale. Contact us for further details. • B-axis (NC rotary table): 360° continuous Pjdpfx Aozg Il Eeahogn • Tooling standard: High-torque configuration for large-scale milling • Additional notes: • Retrofitted in 2008 Technical Specification Taper Size BT 50

Condition: good (used), Year of construction: 2011, Ref. -No.: 10598 Manufacturer: HELLER Type: MC 2000 Year of construction: 2011 Type of control: CNC-Steuerung Control: Siemens 840 D sl Storage location: Halberstadt Country of origin: Hermany Machine-No.: 50XXXX X-Travel: 800 mm Y-Travel: 800 mm Z-Travel: 1000 mm Work spindle torque (25% ED): 242 Nm Pgjdpfx Aasx Hn D Rehon Tool Taper: SK 40 Numbers Of Tools In Magazin: 54 Tool Piece Magazine With: 80 Pcs./pcs. Turning Speeds: 10000 RPM Drive Capacity - Spindle Motor: 17 kW High-Pressure Pump: 50 bar Speed range - main spindle: 10000 RPM Numbers Of Pallets: 2 Size Of Pallet: 630 x 500 mm Weight Of The Machine Ca.: 13000 t spindle running time: 7000 H Operating hours: 14000 H Preparation area: 4 x 90° hydraulic pressure: 200 bar Further information: - The machine has been measured - The geometry is in excellent condition - The spindle runs a little rough - Clamping towers and cutting tool holders are also included - 2 additional clamping towers - 2 replacement pallets - 2-axis servo tool changer - Scraper conveyor for dry machining - Cold light in the work area - Central cooling unit for motor spindle and control cabinet - Control unit at the workpiece setup station - NC-controlled rotary table - Clamping hydraulics The machine can be viewed under power by appointment.

Condition: good (used), Year of construction: 2017, Ref. -No.: 10596 Manufacturer: HELLER Type: H - 2000 Year of construction: 2017 Type of control: CNC-Steuerung Control: Siemens 840 D Storage location: Halberstadt Country of origin: Germany Machine-No.: 56XXX X-Travel: 630 mm Y-Travel: 630 mm Z-Travel: 630 mm B-Axis: 0,001 ° Table Load: 500 kg Max. Tool Length: 350 mm Max. Tool Diameter: 160 mm Tool Taper: HSK 63 Numbers Of Tools In Magazin: 80 Turning Speeds: 16000 RPM Tool changer: Doppelgreifer Max. Workpiece height: 850 mm Max. Torque: 95 Nm Pjdpfx Aaex Hn D Dohogn Rapid Travel X/Y/Z: 60 mm / min Rapid Traverse X-Axis: 80 m / min Rapid Travel Y-Axis: 80 m / min Rapid Traverse Z-Axis: 90 m / min Drive Capacity - Spindle Motor: 40 kW Internal cooling: 50 bar Numbers Of Pallets: 2 Size Of Pallet: 400 x 500 mm spindle running time: 1000 H Operating hours: 3000 H Workpiece interference circuit max.: 720 mm Media interface: 5 - fach Further information: - Equipped with NC rotary table. - State-of-the-art spindle technology. - Ideal for precise machining tasks. - Spindle hours: 1000. - Pallet can be rotated manually 4 x 90 - Hydraulic pressure 200 bar - Quick drill breakage check Machine can be viewed under power by arrangement

Condition: good (used), Year of construction: 2011, Ref. -No.: 10565 Manufacturer: TOYODA Type: FH 630 SX Year of construction: 2011 Type of control: CNC-Steuerung Control: Fanuc 31i - A Storage location: Halberstadt Country of origin: Japan Serial no.: NS3XXXX X-Travel: 1000 mm Y-Travel: 800 mm Z-Travel: 850 mm B-Axis: 360 ° Distance Spindle /Table: 200 - 1050 mm Max. Workpiece Weight: 800 kg Max. Tool Weight: 27 kg Max. Tool Length: 545 mm Max. Tool Diameter: Ø120 mm Max. Size Of Workpiece Lxwxh: Ø 1000 x 1000 mm Tool Taper: BT - 50 Tool Piece Magazine With: 60 Pcs./pcs. Spindle Speed: 6000 RPM Rapid Travel X/Y/Z: 60 mm / min Tool to tool: 2,4 sec Machine length: 7000 mm Machine width: 3500 mm Weight Of The Machine Ca.: 20,1 t Pallet height: 1200 mm Positioning (X, Y and Z axes):: + - 0,003 mm Repeatability (X, Y and Z axes):: + - 0,0015 mm Payload pallet: 800 kg Axial: 14700 N Further information: - Cutting feed (same for X-, Y- and Z-axis): 0.001 - 30m/min - Distance between spindle center and upper edge of the area: 100mm - 900mm - Table size range: 630 mm - Positioning of the lower table: 1 ° Pedoxvw I Ijpfx Aahegn - Positioning of the rotary table: 0.001 ° - Tools used: SK 50 - Operating oil: 53l - Slide lubricating oil / spindle head lubrication: 3.0 l - Coolant for spindle & ball screw head: 37l Machine can be inspected under power by arrangement.

Condition: good (used), Year of construction: 2008, Ref. -No.: 10564 Pgodpfx Aaoxvw Izehon Manufacturer: TOYODA Type: FH 630 SX Year of construction: 2008 Type of control: CNC-Steuerung Control: Fanuc 31i - A Storage location: Halberstadt Country of origin: Japan Serial no.: NS2XXX X-Travel: 1000 mm Y-Travel: 800 mm Z-Travel: 850 mm B-Axis: 360 ° Max. Workpiece Weight: 800 kg Max. Tool Weight: 27 kg Max. Tool Length: 545 mm Max. Tool Diameter: Ø 120 mm Max. Size Of Workpiece Lxwxh: Ø 1000 x 1000 mm Tool Taper: BT - 50 Tool Piece Magazine With: 60 Pcs./pcs. Spindle Speed: 6000 RPM Machine length: 7000 mm Machine width: 3500 mm Weight Of The Machine Ca.: 20,1 t Further information: - Equipped with IKZ and chip conveyor - NC rotary table 360,000 * 0.001° Machine can be inspected under power by arrangement.

Condition: good (used), Year of construction: 2012, Ref. -No.: 10558 Manufacturer: YOU JI Type: HMC 1200 BP Year of construction: 2012 Type of control: CNC-Steuerung Pjdpfx Aaoxxpbxehegn Control: FANUC Series 18i-MB Storage location: Halberstadt Country of origin: Taiwan X-Travel: 1800 mm Y-Travel: 1500 mm Z-Travel: 1360 + 990 mm B-Axis: 360 ° W-Axis: 700 mm Table Dimensions (Lengthxwidth): 1200 x 1400 mm Table Load: 5.000 kg Max. Tool Weight: 25 kg Max. Tool Length: 400 mm Max. Tool Diameter: 125 mm Spindle Speed: 30 - 3.500 RPM Numbers Of Pallets: 2 Further information: 4-axis simultaneous machining IKZ (internal spindle cooling) AKZ (external spindle cooling) Synchronized walking (rigid thread cutting) Renishaw RMP60 workpiece probe (radio) Number of pallet changers for automatic pallet change: 2 Size: 1200 x 1400 mm Tool magazine, number of tools: 60 The machine is currently in production and can be viewed by appointment.

Condition: excellent (used), Year of construction: 2007, CNC Control: MSX-501III X axis mm: 730 Y axis mm: 730 Z axis mm: 850 B axis mm: 0.001 Pallet size mm: 500 x 500 Pjdjythprjpfx Aahegn Number of pallets: 2 Table load capacity kg: 500 Cutting feed mm/min X, Y, Z: 50,000 Max. rapid traverse m/min X, Y, Z: 50, 50, 50 Spindle speed rpm: 14,000 Spindle power kW: 22/18.5 Taper type: BT-40 Torque Nm: - Tool changer type: Chain Tool magazine positions: 60 Max. tool diameter mm: 70 Max. tool diameter with adjacent pockets empty: 140 Max. tool length mm: 500 Max. tool weight kg: 8 Coolant tank capacity l: 760 Through-spindle coolant bar: Yes Equipment Chip conveyor Internal coolant Rigid tapping Manuals, electrical diagrams, etc.

Condition: excellent (used), Year of construction: 2011, TECHNICAL DETAILS CNC control: MSX-501III X axis mm: 560 Y axis mm: 560 Z axis mm: 660 B axis deg.: 360.000 Table load capacity kg: 400 Cutting feed rate mm/min X,Y,Z: 60,000 Max. rapid traverse m/min X,Y,Z: 50 Spindle speed rpm: 12,000 Spindle power kW: 15 Taper type: ISO-40 Torque Nm: 120 Tool changer type: Chain Tool changer positions: 60 Max. tool diameter mm: 70 Podpfx Asxfka Neahjgn Max. tool diameter with adjacent positions empty mm: 170 Max. tool length mm: 450 Max. tool weight kg: 8 Coolant tank capacity l: 500 Through-spindle coolant (high-pressure): Yes EQUIPMENT Double chip conveyor ISO-40 taper High-pressure through-spindle coolant with pump Tool breakage detection probe Part measuring probe RENISHAW MACHINE DIMENSIONS Length mm: 3,755 Width mm: 2,300 Height mm: 2,610 Weight kg: 7,600

Condition: used, Year of construction: 2006, operating hours: 59,800 h, machine/vehicle number: IntNr231615, A compact, high-precision horizontal CNC bar feed milling machine is for sale: ALMAC FB 1005 CNC, manufactured in 2006, equipped with a FANUC 16i-MB / 161MB control system. Technical data: Manufacturer: ALMAC / Tornos Type: FB 1005 CNC Year of manufacture: 2006 Control system: FANUC 16i-MB / 161MB Axes: 6 axes Travel ranges X / Y / Z: 280 / 230 / 120 mm Working feed rate X / Y / Z: Rapid traverse: 12 m/min Resolution: 0.001 mm Front spindle block: with spindles Side spindle block: 4 spindles Vertical spindle block: 4 spindles Parting spindle: 1 spindle Rear machining: 2 or 3 spindles Pedpfxjzgggbs Aahjgn Standard spindle: Speed: 1,000–12,000 rpm Power: 1.4 / 3.4 kW Parting spindle: Speed: 100–3,000 rpm Power: 1.4 / 3.4 kW Tool holder: ESX 20 / HSK 32-A Indexing table / C-axis: Bar feed: Pneumatic: 25 mm or CNC W-axis: 50 mm Swiveling / B-axis: Manual: 0–20° or CNC B-axis: 0–20° or -5° to +45° for short bars Coolant system: Coolant tank: 205 l Flow rate: 40 l/min Standard filtration: 35 µm / 28 µm Temperature control: 3,000 W for ΔT 3 °C Connection data: Installed power: 10 kVA Voltage: 3 × 400 V / 50 Hz Compressed air: 6 bar Dimensions with bar support: L × W × H: 1,800 × 4,250 × 2,060 mm Weight: approx. 1,800 kg The machine can be inspected in operation by prior arrangement. Subject to changes, errors and prior sale.