Floor Plates

Condition: ready for operation (used), Year of construction: 2000, operating hours: 6,328 h, functionality: fully functional, machine/vehicle number: 11180000573, travel distance X-axis: 1,250 mm, travel distance Y-axis: 880 mm, travel distance Z-axis: 800 mm, workpiece weight (max.): 1,000 kg, spindle speed (max.): 18,000 rpm, TECHNICAL DETAILS Travel range X-axis: 1,250 mm Travel range Y-axis: 880 mm Travel range Z-axis: 800 mm C-axis indexing: 360° (0.001°) Feed rate: 40 m/min Rapid traverse: 40 m/min Number of pallets: 1 Pallet dimensions, diameter: 1,000 mm Max. workpiece weight: 1,000 kg Max. torque: 7,900 Nm Max. spindle speed: 18,000 rpm Spindle drive power: 15 kW at 40% duty cycle Spindle drive power: 10 kW in continuous operation Tool interface: CAT 40 Knedpfxezxf Ine Ahgob Number of tool positions in the magazine: 60 Tool changer: Double gripper MACHINE DETAILS CNC control: 3D contouring control MillPlus Total power consumption: 55 kVA Coolant tank capacity: 600 l Dimensions (L x W x H): 7,000 x 3,500 x 3,902 mm Operating hours Hours under power: 33,831 h Spindle operating time: 6,328 h EQUIPMENT Electronic handwheel Chip conveyor Internal coolant supply Rotating viewing windows Flushing gun Preparation for Renishaw probe Accuracy package Preparation for internal cooling with 40/80 bar Paper band filter

Condition: used, Year of construction: 1982, Technical details: faceplate diameter: 2600 mm turning diameter over support: 2500 mm turning length: - mm centre distance: 1600 mm turning diameter over bed: 2900 mm spindle bore: 100 mm revolution per minute: gear steps U/min feed range: Überdrehen 0,12-31,5 Plandrehen 0,12-45 mm/min bed guideways length: 2900 mm max. workpiece weight between centres: 400.000 kgs total power requirement: 45 kW weight of the machine ca.: alle Komponenten zusammen: ca. 29,0 t machine dimensions LxWxH: 5.2 x 5,0 x 3,1 m 3-way measuring system with digital display RSF electronics Knodpfxjwtctyj Ahgeb Control panel Cooling unit for Rittal electric cabinet *

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, center width: 1,200 mm, overall weight: 7,000 kg, travel distance X-axis: 500 mm, travel distance Z-axis: 800 mm, controller model: Bosch Rexroth MTX, TECHNICAL DETAILS Center distance: 1,200 mm Max. outer diameter: 350 mm Max. workpiece weight between centers: 50 kg Ksdpfx Ahozwm Akjgsnb Cross slide, X-axis Travel, X-axis: 500 mm Max. speed: 30 m/min Resolution: 0.1 µm Longitudinal slide, Z-axis Travel, Z-axis: 800 mm Max. speed: 30 m/min Resolution: 0.0005–0.1 mm Multi-function head, B-axis Swivel range: -45° to +225° Swivel time for 180°: < 3 s Positional accuracy: 0.0002° Repeatability: 1″ Resolution: 0.001° External machining Max. machining length: 750 mm Peripheral speed: 50 corundum / 80 CBN Drive power: 15 kW Max. grinding wheel dimensions: Ø 400 × 50 × 152.4 mm Internal machining Max. bore diameter: 250 mm Max. bore depth: 235 mm Drive power S1: 1.8–7.5 kW Speed range: 30,000–50,000 rpm Workpiece spindle, C-axis Max. speed: 1,500 rpm Drive power: 1.8 kW Drive torque: 90 Nm Resolution of measuring system: 0.001° Roundness accuracy: 0.8 µm Positional accuracy: 0.0001° Tailstock Quill stroke: 50 mm / 80 mm Quill diameter: 60 mm Bearing: hydrostatic Fine adjustment for cylindricity corrections: ± 40 µm 3-point steady rest Clamping range, diameter: 20 – 150 mm Coarse adjustment: 40 µm Fine adjustment: 2 µm Adjustability: stepless MACHINE DETAILS CNC control: Bosch Rexroth MTX Dimensions & Weight Dimensions (L x W x H): 2,850 x 2,470 x 2,290 mm Weight: 7,000 kg EQUIPMENT 3-point steady rest

Condition: ready for operation (used), Year of construction: 1988, functionality: fully functional, overall weight: 7,500 kg, grinding diameter: 300 mm, controller model: Siemens Sinumerik 840D Solutionline, No minimum price – guaranteed sale to the highest bidder! The control system was upgraded to a Siemens Sinumerik 840D Solutionline in 2014. The new control system was overhauled in 2016! TECHNICAL DETAILS Spindle speed range: 170–18,000 rpm Grinding diameter: 20–300 mm Swinging diameter: 350 mm (500 mm) Ksdpfx Ahszwmz Tegsnb Workpiece length: 300 mm (1,300 mm) Recommended grinding depth: up to 300 mm Center height above the workpiece table: 200 mm (300 mm) Center height above the grinding table: 330 mm (430 mm) Workpiece spindle bore: 50 mm (70 mm) Grinding table, Z-axis Total grinding table travel: 650 mm (950 mm) Resolution: 0.001 mm Rapid traverse: 12 m/min Grinding feed rate: 0–9.99 m/min Feed rate: 0–99.99 m/min Incremental feed value during reversal: 0–0.999 mm Grinding table, X-axis Total grinding table travel: 150 mm Resolution: 0.001 mm/rev Rapid traverse: 5 m/min/rev Grinding feed rate: 0–5 m/min/rev Feed rate: 0–99.99 mm/min/rev Incremental feed value during reversal: 0–0.999 mm/rev Workpiece spindle head, B-axis Swivel range: −32° (−23°) to +2° Resolution: 0.0001° (0.36″) U-axis Total travel: 300 mm Resolution: 0.001 mm/rev Traverse speed: 5 m/min MACHINE DETAILS Control system: Siemens Sinumerik 840D Solutionline Machine weight: approx. 7.5 t Space requirement: approx. 5.00 × 4.00 × 2.20 m

Condition: good (used), Year of construction: 2016, spindle speed (max.): 3,500 rpm, overall weight: 6,000 kg, Equipment: documentation/manual, rotational speed infinitely variable, Main parameters: Controller: FANUC 0iD/31iA Chuck.: SAMCHULLY 10" Spindle bore: 86mm With jacket tube.:78mm Turret head: 12 main positions 12 secondary positions, BMT65 connection, Programmable hydraulic tailstock: MT5 Main spindle power: 22kW S1max=3500 1/min Living tool power: 5.5kw S2max=5000 1/min X movement range: 260mm Z axis movement range: 830mm Knsdpfx Ajwtg Inohgjb Y axis movement range: + - 52mm (104mm) C axis Maximum turning length: L=760 Largest turning diameter: D=376mm Fast travel speed: 30m/min Automatic tool measurement with probe arm Weight: 6000 kg

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, turning length: 3,000 mm, turning diameter over bed slide: 480 mm, controller model: Siemens 840D, TECHNICAL DETAILS Swinging diameter over bed: 520 mm Swinging diameter over carriage: 480 mm Turning length: 3,000 mm C-axis: yes C-axis speed range: 0–20 rpm Number of tools: 12 Driven tools: 6 Spindle bore: 103 mm Main spindle head size: 8 MACHINE DETAILS Control system: Siemens 840D Main drive Main drive: 1-stage AC main drive Drive power: 53 kW Duty cycle: 50 % Speed range: 30–3,000 rpm Knedpfx Ahozwmztjgob EQUIPMENT Forkardt 3 NHF 315-82 A8 power chuck with centrifugal force compensation and hard, ground-in top jaws Outer diameter of power chuck: 315 mm Bore diameter of power chuck: 82 mm Maximum bar diameter: 63 mm Including draw tube and mounting for power chuck

Condition: ready for operation (used), Year of construction: 1978, functionality: fully functional, overall weight: 9,000 kg, TECHNICAL DETAILS Foot cone angle: 15–55° Pitch circle diameter: 152 mm Tooth height with 21° finishing milling cutter: max. 10.7 mm Tooth height: max. 14.8 mm Tooth width at the tooth root: max. 28 mm Milling cutter diameter: 200 mm Milling cutter diameter according to template: max. 0.21″ (?) Number of teeth range: 8–50 Indexing range: 8–50 mm (?) Machining speed: 49.7 m/min Milling cutter speed: 32.6–49.7 m/min Feed rate: 2–3.1 s/tooth Workpiece spindle Diameter of conical bore at the large end: 99 mm Clamping length: 304.8 mm Taper per foot: 15.4 mm Taper depth: 15.8 mm Countersink behind the taper: 57.2 × 77.9 mm Spindle bore diameter: 22.3 mm MACHINE DETAILS Power of main drive motor: 7.46 kW Speed of main drive motor at 60 Hz: 1,800 rpm Speed of main drive motor at 50 Hz: 1,500 rpm Speed of hydraulic motor at 60 Hz: 1,800 rpm Speed of hydraulic motor at 50 Hz: 1,500 rpm Speed of coolant pump at 60 Hz: 3,600 rpm Knedpfx Aezwmy Nehgob Speed of coolant pump at 50 Hz: 3,000 rpm Speed of chip conveyor motor at 60 Hz: 1,800 rpm Speed of chip conveyor motor at 50 Hz: 1,500 rpm Dimensions & Weight Footprint: 3,200 × 2,210 mm Machine weight: approx. 9,000 kg

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, sheet thickness (max.): 60 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), Equipment: cone bending device, documentation/manual, 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls 570 / 500 / 430 mm Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Knjdjzbqquopfx Ahgob Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, travel distance X-axis: 140 mm, travel distance Y-axis: 100 mm, travel distance Z-axis: 300 mm, workpiece length (max.): 400 mm, The design of the basic machine is characterized by the following features: - Horizontal arrangement of the workpiece spindle; vertical arrangement of the milling spindle or milling head - The workpiece is held between the workpiece spindle housing (left) and the tailstock (right) - The radial slide is mounted on the base (X-axis) - The axial slide moves on the radial slide (Z-axis) - The swivel milling head is equipped with an automatic angular adjustment (A-axis); the swivel slide (Y-axis) moves tangentially to the workpiece diameter TECHNICAL DETAILS Travel range, X-axis: 140 mm Travel range, Y-axis: 100 mm Travel range, Z-axis: 300 mm Tailstock travel, W-axis: 420 mm Swivel angle, end mill head, A-axis, left: 50° Swivel angle, end mill head, A-axis, right: 60° Largest module that can be milled with involute cutters according to DIN 8002: 4.5 mm Largest module that can be milled for high-performance milling: 3.0 mm Number of teeth: 2–999 Workpiece diameter with manual loading: max. 200 mm Workpiece diameter with automatic loading: max. 150 mm Workpiece length: max. 400 mm Milling spindle speed range, B-axis: 0–1,500 rpm Workpiece speed, C-axis: 0–350 rpm Milling tool data Milling tool diameter: 40–102 mm Milling tool length: max. 230 mm Radial front diameter (standard): 16–32 mm Milling coordinates Z-axis: 100–400 mm X-axis: 130–150 mm Y-axis (face of milling spindle): 50–230 mm Knjdpfx Ahszwmyisgjb W-axis (face of tailstock spindle): 165–585 mm Feed rate, X-axis: 3,500 mm/min Feed rate, Z-axis: 3,500 mm/min Feed rate, Y-axis: 4,000 mm/min Feed rate, W-axis: 5,500 mm/min Feed rate, V-axis (portal loader): 80,000 mm/min EQUIPMENT IBH control system Loading device A wide range of accessories

Condition: ready for operation (used), Year of construction: 1997, operating hours: 13,465 h, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, table load: 1,000 kg, controller model: Heidenhain iTNC 430, TECHNICAL DETAILS Travel range, X-axis: 600 mm Travel range, Y-axis: 450 mm Travel range, Z-axis: 400 mm Table load: max. 1,000 kg Tool holder: SK 40 MACHINE DETAILS Control system: Heidenhain iTNC 430 Operating voltage: 400 V Knjdpfezwmx Sox Ahgsb Control voltage: 24 V Machine weight: approx. 6,000 kg Operating hours: 48,690 h Spindle hours: 13,465 h EQUIPMENT Tool holders SK 40 Documentation Heidenhain programming manual Machine vise Clamping jaws

Condition: good (used), Year of construction: 1984, max. wheel diameter 250 mm gear width 275 mm max. module 6 weight of the machine ca. 5,5 t The gear hobbing machine ZFWZ 250 is suitable for the economical production of all hob-processable cylindrical gear types, such a: - spur and helical gear, wormgears and worms, splined shafts, keyed shafts, serrated profiles, chain wheels and ratchet wheels,as well as conical and crowned spur and helical gears. Interchangeable wheels Knjdpjv T Nqaefx Ahgjb and milling accessories Technical data: - Workpiece diameter (max): 250 mm - Module (max): 6 mm - Axial feed travel (max): 275 mm - Tangential feed travel (max): 100 mm - Tooth helix angle (max): 45 degrees - Milling cutter diameter (max): 145 mm - Milling cutter length (max): 170 mm - Table clamping surface (min): 195 mm - Table clamping surface (max): 470 mm Power Milling cutter speeds - Stepped in 2 ranges: 56 ... 250 rpm - (Standard version): 90 ... 400 rpm - Infinitely variable in 2 ranges: 63 ... 180 rpm - (special version DC motor): 140 ... 400 rpm Weights - Machine net: approx. 5000 kg - Electrical cabinet: approx. 800 kg - Hydraulic unit + coolant tank + chip transport: approx. 700 kg Overall dimensions (with oil mist filter) - Length: Standard version: 3950 mm DC drive: 3450 mm (or 3350 mm according to table) - Width: 3300 mm - Height: Machine: 1980 mm Machine with DC drive: 2150 mm Electrical cabinet: 2200 mm

Condition: ready for operation (used), Year of construction: 1998, functionality: fully functional, machine/vehicle number: 570602, travel distance X-axis: 300 mm, travel distance Y-axis: 400 mm, controller model: Siemens Sinumerik 840 C, swivel angle A-axis (min.): -170 °, swivel angle A-axis (max.): 170 °, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range, X-axis: 300 mm Travel range, Y-axis: 400 mm Knsdpfxezwmx Eo Ahgeb A-axis: -170° to +170° X-axis speed: 0.1–5,000 mm/s Y-axis speed: 0.1–5,000 mm/s Workpiece diameter with 1:10 reduction ratio: 300 mm Workpiece diameter with 1:1 reduction ratio: 212 mm Maximum number of teeth: 200 Minimum number of teeth: 6 MACHINE DETAILS Control system: Siemens Sinumerik 840 C Total power requirement: 38 kW Dimensions & Weight Space requirement: approx. 4,200 × 2,200 × 2,100 mm Machine weight: approx. 10,000 kg

Condition: used, Year of construction: 2005, turning length: 705 mm, turning diameter: 356 mm, travel distance X-axis: 260 mm, travel distance Z-axis: 795 mm, controller model: MORI SEIKI MSX-850, TECHNICAL DETAILS Turning diameter: max. 356 mm Standard turning diameter: 275 mm Turning length: max. 705 mm Travel in X-axis: 260 mm Travel in Y-axis: ±50 mm Total travel in Y-axis: approx. 100 mm Travel in Z-axis: approx. 795 mm Knsdpfozwgwzex Ahgeb Rapid traverse rate X/Y/Z: 30 m/min Tool stations: 12 MACHINE DETAILS Design: SY with Y-axis Control system: MORI SEIKI MSX-850 Bar feed magazine: LNS Quick Load Servo 2 Bar length: max. approx. 1,500–1,600 mm / 63″ EQUIPMENT Tailstock Driven tools Y-axis LNS Quick Load Servo 2 bar feed magazine

Condition: good (used), Year of construction: 1994, functionality: fully functional, feed length X-axis: 500 mm, feed length Y-axis: 430 mm, feed length Z-axis: 400 mm, spindle speed (max.): 3,550 rpm, spindle speed (min.): 17 rpm, For sale is a CNC / conventional milling machine of the Hermle brand and type UWF 802 M The machine is in good - very good condition and ready for immediate use Technical data Year of construction: 1994 Kedpfxervitls Ahgenb Control: Heidenhein TNC 124 Clamping: Rigid angle table Speed: 17 to 3550 rpm Feed: Stepless Drive power: 6 KW Travel X 500 mm Travel Y: 430 mm Z travel: 400 mm Tool holder SK40 Dimensions: L*W*H: 1800*1800*1900 mm Weight: 1.8 t On request, loading and transport (Europe-wide) can be organized for an additional charge. Prices plus VAT Viewing possible by appointment. Please contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: used, Year of construction: 2006, turning length: 1,298 mm, turning diameter: 356 mm, spindle speed (max.): 4,000 rpm, controller model: MORI SEIKI MSX 850III / MAPPS III, center width: 1,250 mm, TECHNICAL DETAILS Maximum turning diameter: 1,250 mm Maximum turning length: 1,298 mm Maximum turning diameter: 356 mm Standard turning diameter: 275 mm Swinging diameter over bed: 923 mm X-axis travel: 260 mm Z-axis travel: 1,345 mm Maximum spindle speed: 4,000 rpm Spindle bore: approx. 80 mm Number of turrets: 1 Number of tool positions: 12 MACHINE DETAILS Kedezwgquepfx Ahgenb Control system: MORI SEIKI MSX 850III / MAPPS III Dimensions & Weight Dimensions (L x W x H): 5,000 × 2,300 × 2,400 mm Machine weight: 7,600 kg EQUIPMENT IRCO SIMAG loader magazine Chip conveyor Powered tools C-axis Y-axis