Angular Clamping Device

Condition: ready for operation (used), Year of construction: 2021, operating hours: 590 h, functionality: fully functional, table length: 6,000 mm, table width: 2,000 mm, Machine with only 590 cutting hours! Submitting a bid obligates you to collect the machine by June 30, 2026! TECHNICAL DETAILS Table length: 6,000 mm Table width: 2,000 mm Piercing: up to 16 mm Maximum permissible sheet metal thickness: 100 mm MACHINE DETAILS Operating hours Machine running hours: 5,400 h Cutting hours: 590 h EQUIPMENT Power source: Hypertherm Powermax 65 Hodjzc Euqopfx Agmonn Pin marker TEKA filter system Thanks to a compatible cutting head, 125 amps are possible with the installation of a new power source.

Condition: used, functionality: fully functional, machine/vehicle number: D20E/8022, Offer Number: D20E/8022 Machinetype: multiple wire drawing machine - dry Info: straight through Make: VEB Type: 8 Block Constr. year: inlet wire diameter: 2,5 mm finished wire diamter: 0,8 mm number of drafts: 8 diameter of capstan: 400 mm speed -meters/sek: 15 m Hnjdpfowi Tidox Agmsn Location: Europe

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2006, operating hours: 15,000 h, punching force: 18 t, sheet thickness (max.): 8 mm, travel distance X-axis: 3,050 mm, travel distance Y-axis: 1,550 mm, workpiece weight (max.): 230 kg, MACHINE DETAILS Format: Large format Beam operating hours: 15,000 hours Laser operating hours: 59,000 hours EQUIPMENT Sheetmaster Toolmaster Note: The machine will continue to be operational until 07/09/2026! Hedsza Urgspfx Agmjnn The following data is taken from a manufacturer's data sheet. The seller cannot guarantee the accuracy of the data (the data sheet is attached to the listing): TECHNICAL DETAILS Travel range X-axis: 3,050 mm Travel range Y-axis: 1,550 mm Sheet thickness max.: 8 mm Punching force max.: 180 kN Workpiece weight max.: 230 kg

Condition: ready for operation (used), Year of construction: 2009, operating hours: 22,000 h, functionality: fully functional, turning length: 600 mm, turning diameter over cross slide: 410 mm, spindle speed (max.): 22,000 rpm, controller model: Heidenhain 4290, Submitting a bid obligates the buyer to collect the machine by June 24, 2026! The machine will be dismantled on June 17, 2026, and then stored temporarily. The Z1 linear guide was recently renewed, and the S2 revolver drive was recently replaced. TECHNICAL DETAILS Hnjdszcpwcspfx Agmjn Turning length: 600 mm Turning diameter over cross slide: 410 mm Spindle speed: 22,000 rpm Tool turret: 12-position Tool holder: VDI 40 MACHINE DETAILS Control system: Heidenhain 4290 Operating hours Total operating hours: approx. 87,000 h Spindle hours: approx. 22,000 h EQUIPMENT Large accessories package Powered tools from WTO Note: The seller can offer transport of the machine within Europe for an additional fee (offer upon request).

Condition: new, Bernardo universal lathe Titan 660 x 2000 Technical Specifications Centre distance 2000 mm Centre height 330 mm Swing diameter over bed 660 mm Swing diameter over cranking 900 mm Swing diameter over cross slide 460 mm Bed width 400 mm Spindle bore 105 mm Spindle mounting DIN 55029, D1-8 Speed range (16) 25 - 1600 rpm Range of longitudinal feeds (25) 0.044 - 1.48 mm/U Plan feed range (25) 0.022 - 0.740 mm/U Metric threads (54) 0.45 - 120 mm inch thread (54) 7/16 - 80 Gg/1″ Hedpfsfbbx Rjx Agmonn Pinol diameter 90 mm Sleeve travel 235 mm Sleeve holder MK 5 Engine power 7,5 kW (10,0 PS) Machine dimensions (W x D x H) 3630 x 1200 x 1520 mm Weight approx. 2900 kg Features & Benefits Versatile application possibilities in general mechanical engineering, production, single part production, ... Central, handy switch for feeds and threads with guide and feed spindle Prism bed made of grey cast iron, inductively hardened and precision ground Modern main spindle bearings with angular contact roller bearings in precision design Hardened and ground gears and shafts, also in the feed gear Rapid traverse lengthwise and flat as standard to reduce non-productive times Large spindle bore (105 mm) for large diameter workpieces Soft start due to the mechanical multi-disc clutch Electromechanical foot brake to reduce non-productive time Best cutting performance even during face turning For stiffening the bed guide and for minimizing

Condition: ready for operation (used), Year of construction: 2002, operating hours: 53,548 h, functionality: fully functional, machine/vehicle number: 01160014061, turning length: 630 mm, turning diameter: 420 mm, vice opening: 66 mm, control type: CNC control, Equipment: chip conveyor, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Working area Turning diameter: max. 420 mm Hedpoza D Rfjfx Agmonn Turning length: max. 630 mm Spindle bore: 66 mm Turret Tool head: 12 tools, Sauter VDI30 CNC control: 4290 Heidenhain MACHINE DETAILS Electrical data Voltage: 400 V Auxiliary voltage: 230 V / 24 V Frequency: 50 Hz Current: 80 A Connected power: 44 kVA EQUIPMENT C-axis with driven tools Machine chip conveyor Documentation 2 driven tool holders External reference: 598

Condition: ready for operation (used), Year of construction: 2010, operating hours: 5,744 h, functionality: fully functional, machine/vehicle number: 6100000012E, turning length: 393 mm, turning diameter: 228 mm, spindle speed (max.): 3,000 rpm, vice opening: 51 mm, Equipment: chip conveyor, No minimum price – guaranteed sale to the highest bidder! Lathe equipped with a tailstock and chip conveyor! TECHNICAL DETAILS Working range Turning diameter: 228 mm Turning length: 393 mm Distance between centers: 51 mm Spindle speed: max. 3,000 rpm Turret Turret head: Sauter VDI30 MACHINE DETAILS Electrical connection data Voltage: 400 V Hnsdpfx Agoza D Iwjmsn Frequency: 50/60 Hz Weight: 3,500 kg Operating hours Power-on hours: 20694 Working hours: 5744 EQUIPMENT Chip conveyor with coolant tank and pumps 3 driven tool holders WTO 4 standard holders VDI30 Tool probe Chuck: Kitagawa 210 mm Tailstock Machine manuals External reference: 603

Condition: used, Year of construction: 2006, functionality: fully functional, center height in crank: 1,100 mm, workpiece weight (max.): 180,000 kg, grinding length: 11,000 mm, grinding wheel diameter: 1,066 mm, total length: 11,700 mm, quill travel distance: 11,700 mm, workpiece weight between centers: 180,000 g, distance between centers: 11,700 mm, POMINI CNC Roll Grinder Model HD-425-2-7L Siemens 840D, 12 Axes. Built in 2006. Two flatbed system grinding and workpiece ways are separate. Hnedpfx Aowdmy Sjgmsn Machine accuracy. Straightness 0.001-0.002 mm/m. Roundness 0.001-0.002 mm. Eccentricity 0.002 mm. Profile for crown height up to 0.1 mm ±0.002 mm/m. Surface finishing without chatter marks and no feed marks after finishing grinding stage. On an independent bed: Auto Caliper Diameter 870 - 2,250 mm. Eddy current crack and bruise detector probe. Ultrasound depth probe up to 180 mm. High Pressure wheel cleaner. Wheel dynamic balancing electromagnetic automatically or manually. Wheel dressing device with diamond. 2 Hydrostatic Steadies. 2 Hydrodynamic Steadies. 4 Soft landing for roles. Wheel quick change device incl motor. Jib crane. Vibration Measurement, recording on: Headstock base Neckrests Foot stock Wheel head Wheel head back Carriage Lateral side. Working Capacity. Grinding length 11,000 mm Max diameter with 1,066 mm Grinding wheel 2,200 mm Min diameter with 1.066 mm Grinding wheel 800 mm Center distance 11,700 mm Max Roll weight 80 Tons Max Roll weight with Steadies 180 Tons Min distance between wheel center and roll axis 845 mm Max distance between wheel center and roll axis 1,635 mm Carriage Axis Z, Hydrostatic Feeds, Infinitely variable 0-6,000 mm/min Oil film thickness 0.020 mm Distance between carriage ways 1,500 mm Ways width 160 mm Total length of the carriage on ways 3,385 mm Wheelhead on Carriage Axis X, Wheel Probe Axis A, Inspector Axis A1, Wheelhead cross travel Ballscrew, Axis X 940 mm Resolution axis X 0.0001 mm Wheel Spindle length 1,695 mm Spindle bearing, hydrostatic, diameter 254 mm Resolution Infeed micrometer handwheel, Axes X 0.00001 mm / division Continuous wheel infeed, U axis on radius 0 - 0.35 mm/min Rapid wheel indeed, axes X 0-830 mm/min Wheel motor, AC 130 kW Wheel Speed 400-1,100-1,600 rpm Wheel Cutting Speed infinitely variable Surface speed wheel diameter 1,066 mm 45 m/sec Surface speed wheel diameter 670 mm 45 m/sec Wheel hole, diameter 508 mm Wheel thickness 76 - 152 mm Wheel diameter 670 - 1,066 mm Crowning, Axis U. Max crown on the diameter 10 mm Max concavity on the diameter 10 etc Head stock Workpiece rotating speed 5 - 50 rpm Headstock motor 200 kW Max transmissible torque 76.5 kNm Faceplate control system V Belts Max Center diameter, metric type 160 mm Stroke of Quill 150 mm Length of headstock 3,110 mm Tail stock Quill diameter 260 mm Stroke of quill 750 mm Maximum center diameter, metric type 160 mm Taper Metric 5% on the diameter Tailstock length 1,300 mm Stroke of tailstock 8,000 mm Caliper, Arm Axis C, Carriage Axis V, Rotation Axis B. Max measurable diameter 2,250 mm My measurable diameter 870 mm Machine Dimensions. Machine weight 130 tons Length 19.5 m. Width 5.5 m. Height 3.2 m. Foundation depth 3.8 m.

Year of construction: 1995, condition: ready for operation (used), functionality: fully functional, total length: 2,100 mm, total width: 730 mm, heating capacity: 7.5 kW (10.20 HP), screw conveyor diameter: 35 mm, machine/vehicle number: DE27307, TECHNICAL DETAILS Capacity: 30 – 80 kg/h Screw diameter: 2 x 35.0 mm L/D ratio: 20:1 Screw speed: 80 rpm Gearbox ratio: 12:1 Number of heating zones: 5 Heating power: 7,500 W Number of cooling fans: 5 Hodpfx Agszargnjmjnn Extruder discharge height: 1,150 mm MACHINE DETAILS Control system: Analog, contactor-controlled system Drive / Motor: 20 kW (DC) Cooling fan connection: 230 V Gearbox type: Lenze Material: PE, PP, PS, ABS Design: Co-rotating, degassing, vacuum pump Dimensions (L x W): 2,100 x 730 mm Note: Water bath and granulator can be purchased for an additional charge.

Condition: ready for operation (used), Year of construction: 2016, functionality: fully functional, travel distance X-axis: 760 mm, travel distance Y-axis: 430 mm, travel distance Z-axis: 460 mm, spindle speed (max.): 10,000 rpm, controller model: Siemens Sinumerik 828D CNC, ATTENTION – Equipment update: Instead of a RENISHAW measuring probe, a Renishaw tool presetter is included! TECHNICAL DETAILS Travel range X-axis: 760 mm Hjdozap Dwjpfx Agmjnn Travel range Y-axis: 430 mm Travel range Z-axis: 460 mm Spindle mount: SK40 Spindle speed: 10,000 rpm Feed rate: 10,000 mm/min Table size X: 900 mm Table size Y: 410 mm Max. workpiece weight: 350 kg Number of axes: 3 MACHINE DETAILS Control system: Siemens Sinumerik 828D CNC Tool changer: 24-position Drive power: 12 kW Tool cooling through the spindle: 30 bar EQUIPMENT Renishaw tool presetter Chip conveyor

Year of construction: 1998, condition: good (used), Make: UNION Type: Ti 1800 Year: 1998 Specifications Metric US Standard Table Length 2000 mm Table Width 1800 mm Table load 16000 Movement V-axis 1250 mm Rotation B-Axis 360.000 ° Rotation speed B-Axis 1,35 Omw/min. Movement speed V-axis 4000 mm/min. Dimensions (Estimate) Length 3400 mm Width 2000 mm Hjdpfx Aokwcdbogmsnn Height 920 mm Weight 6500 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, travel distance X-axis: 400 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 300 mm, workpiece weight (max.): 500 kg, controller model: Mitsubishi 32-bit EDM Steuerung, TECHNICAL DETAILS Hjdpfxozapyle Agmjnn Travel range X-axis: 400 mm Travel range Y-axis: 300 mm Travel range Z-axis: 300 mm Max. workpiece size X: 700 mm Max. workpiece size Y: 500 mm Max. workpiece size Z: 250 mm Max. electrode weight: 50 kg Max. workpiece weight: 500 kg Table size X: 550 mm Table size Y: 470 mm MACHINE DETAILS Control: Mitsubishi 32-bit EDM control Electrode changer: 20-position Generator: 50 A EQUIPMENT Lowerable container

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, cutting height (max.): 250 mm, cutting width (max.): 280 mm, saw band length: 2,950 mm, saw band speed: 1,667 mm/s, saw band width: 27 mm, TECHNICAL DETAILS Saw band dimensions: 2,950 x 27 x 0.9 mm Speed: 15-100 m/min Vise opening: 285 mm Cutting capacity at 90° (round): 250 mm Cutting capacity at 90° (square): 220 mm Cutting capacity at 90° (rectangular): 280 x 220 mm Cutting capacity at 60° (round): 120 mm Cutting capacity at 60° (square): 80 mm Cutting capacity at 60° (rectangular): 140 x 100 mm Cutting capacity at 45° (round): 230/200 mm Cutting capacity at 45° (square): 200/170 mm Cutting capacity at 45° (rectangular): 220 x 200/200 x 140 mm Control: conventional MACHINE DETAILS Total power requirement: 2.2 kW Weight: 990 kg Machine dimensions: 2,500 x 2,230 x 2,050 mm Hnodszapxzepfx Agmsn

Year of construction: 2006, condition: ready for operation (used), A Pinacho CNC precision parallel lathe is available. Center height: 180mm, center width: 750mm-1000mm, turning diameter over guide bed/longitudinal slide/cross slide: 360mm/335mm/198mm, bed width: 250mm, bore: 42mm, speed: 4000rpm, feed X/Z: 10m/min, rapid traverse X/Z: 10m/min. Tailstock shank diameter: 58mm, tailstock shank length: 200mm, Morse taper: MK3, min. travel of moving/fixed steady rest: 10mm, max. travel of moving/fixed steady rest: 70mm/114mm, control: Fanuc 0i. Documentation available. On-site inspection is possible Hnsdpfx Aowftcvjgmen

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, cutting height (max.): 260 mm, cutting width (max.): 320 mm, saw band length: 3,150 mm, saw band speed: 667 mm/s, saw band width: 25 mm, TECHNICAL DETAILS Saw band dimensions: 3,150 x 25.4 x 0.9 mm Speed 1: 20 m/min Speed 2: 40 m/min Cutting capacity at 90° (round): 260 mm Cutting capacity at 90° (square): 250 mm Hodpfx Agszapv Tomjnn Cutting capacity at 90° (flat): 320 x 200 mm Cutting capacity at 45° (round): 230 mm Cutting capacity at 45° (square): 210 mm Cutting capacity at 45° (flat): 240 x 200 mm Control: NC EQUIPMENT - Saw band storage