Moulder

Leadermac 923 Hu

Condition: excellent (used), Calibration and fine sanding machine with 1 sanding unit 1 motor, processing from above Working width 1000 mm Sanding belt dimensions 2200 x 1030 mm Workpiece dimensions 3 - 170 mm Table height adjustment motor 0.18 kW, 400 V, 50 Hz Main motor 7.5 kW, 400 V, 50 Hz 2 feed speeds 5.5 & 11 m/min 1st unit: Combination unit, sanding drum, rubberized, 90 Sh / pneumatic sanding pad Sanding pad NEW 2nd unit: Cleaning brush Compressed air requirement approx. 6 bar Suction diameter 200 mm Dimensions approx. L x W x H = 1385 x 1980 x 1900 mm Weight approx. 1800 kg Automatic workpiece thickness adjustment with digital display Oscillation of the sanding belt Sanding belt emergency stop with disk brakes Table extension with 3 rollers in the outfeed Emergency stop button Main switch Codpfx Aoudxchjbbogn TRANSPORT CARPET LIKE NEW - was replaced by us approx. 3 years ago MORE THAN 30 WIDE BELT SANDERS Note used machines: - Subject to errors in technical specifications and prior sale. - Prices quoted are ex location - free loading! - The machines have been cleaned and functionally tested. - All machines are purchased as seen without any warranty. The buyer is free to inspect the machines on site. - Special agreements are only possible in written form. (Inquiries will only be answered with your address and telephone number).

Condition: used, ALREADY DISMANTLED ‼️ IMMEDIATELY AVAILABLE ‼️ 🔥 Gilles 300 kW Wood Chip Boiler for sale – reliable industrial biomass technology! 🔥 Industrial-scale heating solution with Austrian precision! The Gilles 300 kW boiler is the ideal choice for large facilities, sites, grain dryers, or central heating systems. Key features: 🌲 Fuels: wood chips, pellets, biomass – wide fuel variety ⚡ 300 kW heating capacity – reliable and efficient for heavy-duty users 🔄 Automatic feeding, combustion control, ash removal – minimal personnel required 🧠 Modern control system, optimized combustion ♻️ High efficiency, low emissions 🇦🇹 Gilles = Austrian quality, industrial reliability 💥💰 PRICE: 9,900 EUR – GOOD CONDITION, READY FOR INDUSTRIAL USE! 💰💥 📍 Location: Hungary, 9200 Mosonmagyaróvár, Kötöttárugyári út 22 (ProfiKazán) Cgodpfxep Am Rgj Abbjn ⸻ 💼 Top Heating Systems – ProfiKazán Industrial boilers, biomass solutions, experienced and competent.

Condition: used, Planer table length: 2,500 mm Working width: 260 mm Working height: 160 mm Air cushion table: Yes Spindles: 7 Csdpfx Abjxzdwyobjgn Spindle 1: Bottom / 7.5 kW / 8,000 rpm Spindle 2: Right / 7.5 kW / 8,000 rpm Spindle 3: Left / 7.5 kW / 8,000 rpm Spindle 4: Right / 7.5 kW / 8,000 rpm Spindle 5: Top / 7.5 kW / 8,000 rpm Spindle 6: Top / 7.5 kW / 8,000 rpm Spindle 7: Bottom / 7.5 kW / 8,000 rpm Control: PowerCom Plus Feed rate: 30 m/min / 4 kW Weinig Powermat 500 planing and profiling machine for four-sided planing and profiling of timber with CNC control and Powerlock quick-change system.

Condition: new, Year of construction: 2025, Martin T 54 jointer Only with a good surface planer can you create truly perfect foundations. The T54 was developed with precisely this objective in mind. It enables you to easily plane workpieces at the most modern level and to safely provide them with angular edges. The machine is equipped with a TERSA solid steel cutterhead as standard. The Xplane cutterhead, which operates with a drawing cut, is available as an optional extra. Planing bevels is effortless, as any angle between 90° and 45° can be quickly adjusted with the user-friendly one-hand adjustment. The solid cast iron tables of the T54 provide secure support even for large, heavy workpieces. If you need even more support, you can extend both the infeed and outfeed tables by 380 mm each - of course also in cast iron. Technical data table width: 500mm Table length: 2840mm Maximum chip removal: 8mm cutter: diameter 125mm, 5000 rpm, Tersa Z4 Speed: 5000 rpm Huyjm0s Motor power: 5,5kW Fence adjustable up to 45 Auxiliary ruler for small workpieces Table adjustment motorized Cgsdpfopq If Dox Abben Equipment: T 54 T 5462-a Suvamatic T5406/3-a solid steel cutterhead Xplane with 3 spiral knife rows (26 cambered carbide knives per row; 2 counter knives), delivery includes full knife equipment as well as a T-wrench Torx T20; shaft speed 6,000 rpm included. The emission sound pressure level LpA during machining is reduced by 8 dB(A). Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2024, Cutting capacity: 55x360, 80x340, 95x325, 125x295, 135x280 mm Minimum work piece thickness mm.10 Working table tilted 8° Cutting unit technical features: Pneumatic upstroke saw TR500 Motor power 10 HP (7,5 kW), Volt 400/50 Hz. TCT Blade dia.500 mm., F=30 Z=144 S=4,6 Cutting cycle speed: 4 seconds Push feed system technical features: PUSH FEED SYSTEM AVAILABLE LEFT AND RIGHT SIDE Feeding by rack and pinion system and brushless motor Positioning precision +/- 0,4 mm Strong infeed motor for a packet weight of 80 kgs Maximum push feed system speed 90 m/min Pneumatic rising of the pusher at the end of the cutting cycle and overhead returning. Data entry management: 12 inch TOUCH-SCREEN Controller (800x600 pixel) USB Port Ethernet Port LINUX Operating system Loading and save machine parameters via USB Port Cutting cycle (pattern) editing and entered directly on the controller Transfer of cutting lists created by PC via USB or Ethernet Port Working software: Manual input of loading board length Partial optimization without length reading of the board Cutting cycle with 3 optimization options (Maximum length, Sequence and Board sequence) N°1000 cutting lists made up of 11 sizes or one list of 10000 sizes in sequence Package "OPTI": automatic board length detection and full optimization. Piece length reading by photocell Cutting cycle: with 6 optimizing criteria: (Longest length, Sequence, Board sequence, Volume, Minimum waste and Priority length) Csdpjhw Ng Iofx Abbjgn Package "OPTI PLUS": total optimization with knots and defects removal (OPTION NOT INSTALLED ON THE MACHINE) Technical Description: Package "OPTI PLUS": for knots and defects removal Photocell for reading wood mapping knots and defects Marking with fluorescent chalks/crayon (Note Ð Can only be ordered in combination with ZA250) Pneumatic side clamp device

Condition: new, Year of construction: 2022, functionality: fully functional, Brand New Friulmac EQ 004 2.5 with feeding belt and a feeding hopper Touch-Screen Operation and automatic adjustment Working length - min 190mm - max 2500mm width - min 30mm - max 250mm thickness - min 12mm - max 35mm Speed - 6 - 25m/min Codpfx Abevupm Dsbogn 2 x 2 Hoger - 3kW - 720 rpm Main Profiling Head - 4kW - 7200 rpm For more information I can send you the original documentation

Condition: good (used), Year of construction: 2015, functionality: fully functional, edge thickness (max.): 12 mm, ENGLISH: Heavy duty edgebander OLIMPIC (SCM Group) in rich configuration suitable for custom made and series production. Machine is equipped with aggregates with servomotors (ABS R1+R2mm + thin edge + solidwood). Model: Olimpic K800 TERL Manufacturer: SCM Group Production year: 2015 State: good Edgebanded edges: 238.800 meters Main technical parameters: - feeding speed: 12/18 m/min. (including rounding) - panel thickness: 10-60 mm (including rounding) Equipment and configuration of the machine: - control panel with LCD touch screen STARTOUCH - internal lightning of working area - automatic lubrication of the feeding chain - electronic top pressure adjustment - glue pot with quick change of the glue color Working units: - antiadhesiv spray Cgjdewxt Tbspfx Abbsn - pre-milling unit (2x DIA cutter) - glue pot with roller "VC/1000" (glue pot with quick-release system) - pressure rollers (4 pcs) with timed intervention - 2 motor end cutting unit "K/SEL" with pneumatic tilting of the blades - radius trimming unit "RI/800" R1mm + thin edges + solid wood (12mm) (3 position pneumatic kit) - 2 motor rounding unit "ROUND K MULTI EDGE" R2mm + thin edge (each motor has: 2 electronic axis with servomotor) - radius edge scrapers "RAS/S 2P" MULTI-EDGE R1+R2mm (each unit has: 2 electronic axis with servomotor) - cleaning spray - glue scrapers "RCA/2C" - brushes"SP/F"

Year of construction: 2001, operating hours: 123 h, condition: ready for operation (used), machine/vehicle number: 123, Metal silo for storage of woodchips, etc. Cjdpfx Asftdv Ujbbogn Technical description: silo DM: 5m Height: 8 m with outfeeding unit (screw conveyor connection to output) Cappacity: 42 m3 With outfeeding transport screw conveyor to the top of the silo building. Already dismountled, visit possible by appointment at our warehouse H-2013 Pomáz/Hungary.

Condition: used, Year of construction: 2021, saw blade diameter: 800 mm, rotational speed (min.): 1,450 rpm, power: 5.5 kW (7.48 HP), Crosscut saw AS Very good, well-maintained condition Saw blade diameter 800mm. Sturdy tubular steel base frame. Powerful saw motors. Pneumatic material clamps (3 vertical). 2-hand safety operation. Cgsdpfsd Szf Nsx Abbsn Coolant device. Protective hood. Optionally with length measuring system or automatic positioning system. Version as automatic saw-drilling machine or automatic saw-punching machine on request.

Condition: good (used), Year of construction: 1993, Vecoplan drum chipper VTH 75 / 22 / 5. Infeed dimensions: width 750 mm, height 220 mm. Motor: 75 kW. Codpoxr Tp Hefx Abbsgn