Surface Grinding Machine - Horizontal

KENT KGS 84 WM 1

Condition: excellent (used), Year of construction: 2015, Roll pressure infinitely adjustable from 240 kN feeds - fine adjustment 0,5-45 mm/min turning speeds 0-80 U/min Swivel angle of the roller heads 11 ° Diameter of the roller spindles 69,85 mm Stroke - Roller screw slide 0-150 mm Pgodpfjxukrqjx Ah Hog min. dist. - roller screws 138 mm max. dist. - roller screws 285 mm min. diameter - Rolling tools 230 mm max. diameter - Rolling tools 135 mm min. dia. 2 mm max. diameter 55 mm thread length at plunge operation 200 mm thread length at continiuous operation 2000 mm maximum thread pitch 4 mm total power requirement 14 kW weight of the machine ca. 2,4 t dimensions of the machine ca. 2,0 x 2,5 x 1,9 m Rolling time continuously adjustable from: 0.1s Pause time continuously adjustable from: 0.1s Rolling spindle length: 200mm Machine bed height: 810mm Rolling spindle height above machine bed: 200 mm Height of support bearings: 115 mm Largest pitch for serrated teeth: 2.5 mm (up to 70 kg/mm2 Strength of the material)

Condition: used, Technical details: balancing body max.: 800 kg balancing body diameter: 1250 mm Balancing revolution per minute: 190 - 3600 U/min bed length: 2600 mm voltage: 380 V/Hz drive power: 7,5 kw Pgjdpfxou Upp To Ah Hjg Weight approx.: 1,5 t dimension machine xH: 3,5 x 1,7 x 2,0 m dimensions electric cabinet: B:650 x T:250xH:800 mm Horizontal balancing machine The balancing machine is used to measure and balance the static or dynamic unbalance of rotors. Balancing body weight max. 800 kg with equal load distribution, i.e. 400 kg per bearing pedestal Power transmission by means of cardan shaft Bearing journal Ø min./max.: 16-95 / 95-180 mm Bearing distance center distance min. 125 mm and shaft end bearing center max. 2070 mm Measured speed: 1st gear = 190 - 650 rpm. 2nd gear = 400 - 1250 rpm 3rd gear = 700 - 2100 rpm. 4th gear = 1200 - 3600 rpm. 2 pick-up blocks whose displacement is manual over the entire bed Schenk measuring device with digital display and some accessories, e.g. many rotor shafts with different Ø and different rotor mounts, please ask! *

Condition: good (used), Year of construction: 2009, Ref. -No.: 10616 Manufacturer: DMG Type: DMU 210 P Year of construction: 2009 Type of control: CNC Control: Heidenhain ITNC 530 Storage location: Halberstadt Country of origin: Germany Machine-No.: 257XXXX X-Travel: 1800 mm Y-Travel: 2100 mm Z-Travel: 1250 mm B-Axis: -30 / +180 ° C-Axis: 360 ° Table Load: 8000 kg Clamping Area: 1.700 mm Psdpfjx R R Hcox Ah Hogg Tool Taper: SK 50 Spindle Speed: 10.000 RPM Max. Torque: 288 Nm Total Power Requirement: 38 kW No. Of Working Stations: 60 Internal cooling: 40 bar Holding torque: 22.700 Nm Further information: - The DMG DMU 210 P 5-axis machining center is suitable for high-precision machining of large, heavy workpieces. The machine can be viewed under power.

Condition: good (used), Year of construction: 2004, operating hours: 109,078 h, travel distance X-axis: 650 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 500 mm, rapid traverse X-axis: 45,000 m/min, rapid traverse Y-axis: 45,000 m/min, rapid traverse Z-axis: 45,000 m/min, controller model: Siemens 840 D, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Hermle C30 U Pgedpfx Asxcp Sloh Hog Siemens 840D Machine HOURS: 109,078 h Spindle HOURS: 22,117 h - Spindle HSK-A63 10,000 rpm - 32 tool pockets - Rotary table SRT 280 mm with integrated clamping system SK50 (if not required, this can be closed or alternatively converted for use as a zero-point clamping system) - External coolant supply - Internal coolant supply with paper band filter, 80 bar - Swarf flushing pistol - Chip conveyor - Handheld control unit - Automatic cabin door - 32 tool pockets plus 87 additional ZM87 positions - Thermal compensation - BLUM tool measurement on carriage - Renishaw probe - Chip container - Status indicator light The machine has been thoroughly inspected, and there is a geometry inspection protocol as well as circularity test measurements available. The machine can be viewed and tested under power at any time. Very well-maintained condition.

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 930088, Country of manufacture: CH Voltage: 400V / 50/60Hz / 3ph. Net weight (machine + control cabinet): 3,250 kg + 400 kg Customs tariff number: 8456.30 20 Dimensions: 260 x 281 x 225 cm TECHNICAL SPECIFICATIONS Machining type: immersion Maximum workpiece dimensions: 1200 x 700 x 400 mm Maximum workpiece weight: 1,500 kg Table size: 900 x 600 mm Floor to table distance: 900 mm Total dielectric volume: 1,200 L Axes X, Y, Z, U and V Travel on X, Y, Z axes: 550 x 350 x 400 mm Travel on U, V axes: 550 x 350 mm Anti-collision protection: X, Y, Z, U, and V axes Taper cutting, max. taper: +/- 30° / 400 mm Available wire diameters: Ø 0.25 mm (options: 0.1/0.2/0.3 mm) Wire guide type: closed diamond, gapless Available spool weights and types (DIN standard): 1.6 kg (K 100) to 8 kg (K 160) Available spool weights and types (JIS standard): 3 kg (P3) to 5 kg (P5) Dielectric Paper filters: 2 cartridges Dielectric temperature: +/- 1°C Total deionization resin volume: 20 L Maximum injection pressure: 20 bar Generator: dual Isopulse source Pedpfxsw Ucyuo Ah Hegg Power supply: 380/400V 3-phase Total power: 10 KVA Maximum cutting speed: 400 mm²/min Minimum surface roughness: 0.20 micron Ra Measuring system: glass linear scales Measurement resolution: 0.5 micron Servo motors: AC type Unless otherwise stated, technical specifications are provided without commitment and subject to error or omission.

Condition: good (used), Year of construction: 2001, grinding length: 650 mm, grinding width: 525 mm, total height: 350 mm, table length: 600 mm, table width: 350 mm, Manufacturer: Geibel & Hotz Type: FS 635-Z SA Control: Digital read out Year of construction: 2001 Magnetic table 600 x 350 mm Closed housing for CE Automatic vertical lubrication SA Automatic lubrication Coolant tank Specifications Metric US Standard X - axis 650 mm Y - axis 525 mm Z - axis 350 mm Table length 600 mm Table width 350 mm Table load 400 Feed X - axis 35000 mm/min. Feed Z-axis 1000 mm/min. Grinding stone dimensions 300 x 50 x 76.2 mm Pgedpfxjvdal Ao Ah Heg Power output 3.7 kW Speed 2800 ? rpm Dimensions (estimate) length 3200 mm width 2000 mm height 2870 mm weight 2300 kg Please note: The information on this page has been obtained from the manufacturer to the best of our knowledge and belief, and where possible, the information is given in good faith but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: good (used), Year of construction: 1988, voltage 380 V connected load 7,5 kVA dimensions 2725 x 1930 x 1773 mm Psdpsw Dvkajfx Ah Hegg weight of the machine ca. 2500 kg --> Technical data Main data: --> Table surface: 605 x 300 mm --> Table longitudinal movement max. (manual): 750 mm --> Table transverse movement: 340 mm --> Grinding height between table/new grinding wheel min/max: 22.5 / 322.5 mm --> Standard size of magnetic clamping plate: 600 x 300 mm --> Workpiece weight incl. magnet: 420 kg --> X-axis / longitudinal movement: --> T-slots (number x width): 3 x 17 mm --> Table feed, hydraulic: 0.3 - 25 m/min --> Travel per handwheel revolution: 47 mm --> Y-axis / height movement: --> Automatic vertical feed - coarse in 12 steps: 0.001 - 0.03 mm --> Automatic vertical feed - fine in 8 steps: 0.001 - 0.01 mm --> Distance per handwheel revolution (x1/x10): 0.1 / 1.0 mm --> Graduation on handwheel (x1/x10): 0.001 / 0.1 mm --> Trigger strokes: 0 - 5 --> Rapid traverse: 400 mm/min --> Z-axis / transverse movement: --> Automatic transverse feed intermittent: 0.5 - 20 mm --> Automatic transverse feed / rapid traverse continuous: 0.1 - 1.0 m/min --> Distance per handwheel revolution: 5.0 mm --> Scale mark on handwheel: 0.02 mm --> Standard grinding wheel: --> Ø x width: Ø 355x38 (50) mm --> Bore: Ø 127 mm --> Speed: 1500 rpm --> Accessories Various grinding wheels --> Documentation

Condition: ready for operation (used), Travel X/Y/Z/U/V: 400mm/250mm/400mm/400mm/250mm, max. workpiece dimensions X/Y/Z: 850mm/500mm/400mm, wire diameter: 0.1mm-0.3mm, max. table load: 1000kg, power requirement: 10kVA. Machine dimensions X/Y/Z: approx. 1800mm/1600mm/2230mm, weight: approx. 2800kg. On-site inspection is possible. Psdpjuqacksfx Ah Hogg

Condition: used, Year of construction: 2003, Diesinking / EDM Travel distance X: 350 mm Travel distance Y :250 mm Travel distance Z: 300 mm table size X: 500 mm table size Y: 400 mm max. workpiece size X: 780 mm max. workpiece size Y: 530 mm max. workpiece size Z: 300 mm max. electrode weight: 50 kg max. workpiece weight: 500 kg Pgsdpfevyzf Nex Ah Hjg electrode changer: 4 - time generator: 64 Ampere drop tank control Charmilles

Condition: excellent (used), Grinding length 1000 mm Podek Abxxopfx Ah Hogg grinding diameter fi 350 mm In very good condition.