Cylindrical grinder

KELLENBERGER 600 U

Condition: ready for operation (used), functionality: fully functional, center height: 125 mm, center width: 600 mm, grinding wheel diameter: 400 mm, grinding wheel width: 50 mm, grinding wheel bore: 127 mm, The motor and frequency inverter for the workpiece headstock have been replaced! Additionally, the control cabinet and wiring diagram have been renewed! Hsdeyb R Nqepfx Adaeh TECHNICAL DETAILS Centre height: 125 mm (175 mm with riser blocks) Centre distance: 600 mm Grinding wheel diameter: 400 mm Grinding wheel width: 50 mm Grinding wheel bore: 127 mm Swivel range: 270° Workpiece headstock speed: 20 rpm to 400 rpm Spindle taper: 5 MT Tailstock taper: 3 MT Table swivel: 10° Table feed speed: up to 6.0 m/min MACHINE DETAILS External grinding wheel motor: 4.0 kW Workpiece spindle motor: 2.2 kW Dimensions & Weight Dimensions (L x W x H): 2,580 x 1,680 x 1,670 mm Machine weight approx.: 2,700 kg EQUIPMENT New control cabinet and new wiring diagram New motor and frequency inverter for the workpiece headstock 2-axis digital readout Coolant tank Geometry according to Kellenberger protocol Extensive accessories

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 930088, Country of manufacture: CH Voltage: 400V / 50/60Hz / 3ph. Net weight (machine + control cabinet): 3,250 kg + 400 kg Customs tariff number: 8456.30 20 Dimensions: 260 x 281 x 225 cm TECHNICAL SPECIFICATIONS Machining type: immersion Maximum workpiece dimensions: 1200 x 700 x 400 mm Maximum workpiece weight: 1,500 kg Table size: 900 x 600 mm Floor to table distance: 900 mm Total dielectric volume: 1,200 L Axes X, Y, Z, U and V Travel on X, Y, Z axes: 550 x 350 x 400 mm Travel on U, V axes: 550 x 350 mm Anti-collision protection: X, Y, Z, U, and V axes Taper cutting, max. taper: +/- 30° / 400 mm Available wire diameters: Ø 0.25 mm (options: 0.1/0.2/0.3 mm) Wire guide type: closed diamond, gapless Available spool weights and types (DIN standard): 1.6 kg (K 100) to 8 kg (K 160) Available spool weights and types (JIS standard): 3 kg (P3) to 5 kg (P5) Dielectric Paper filters: 2 cartridges Dielectric temperature: +/- 1°C Total deionization resin volume: 20 L Maximum injection pressure: 20 bar Generator: dual Isopulse source Power supply: 380/400V 3-phase Total power: 10 KVA Maximum cutting speed: 400 mm²/min Minimum surface roughness: 0.20 micron Ra Measuring system: glass linear scales Measurement resolution: 0.5 micron Servo motors: AC type Hodpfxsw Ucyuj Adash Unless otherwise stated, technical specifications are provided without commitment and subject to error or omission.

Condition: good (used), Year of construction: 1997, Ref. -No.: 10619 Hjdpfxjya Daye Adaeh Manufacturer: KELLENBERGER Type: 600 U Nr. 35 Year of construction: 1997 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175 - 250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0- 5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 1500 / 1700 / 2200 / 3600 Swiveling grinding wheel head: 360° ° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Working speeds continuously adjustable (normal / special): 20-400 / 10-400 Max. Grinding length: 900 mm

Condition: good (used), Year of construction: 2003, Ref. -No.: 10618 Manufacturer: KELLENBERGER Type: 600 U Nr. 33 Year of construction: 2003 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175 - 250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0 - 5 Sec Diameter / width / hole: 250 x 13 x 76 mm Hedpsya Dagsfx Adaoh Speeds of the grinding wheel spindle: 1500 / 1700 / 2200 / 3600 Swiveling grinding wheel head: 360 ° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Micro-corrector of the feed, 1 division of the dial: 0,001 mm / Ø Working speeds continuously adjustable (normal / special): 20-400 / 10-400 Max. Grinding length: 900 mm

Condition: as good as new (ex-display), Year of construction: 2013, operating hours: 1,265 h, functionality: fully functional, spindle speed (max.): 20,000 rpm, turning diameter: 4 mm, Equipment: documentation/manual, rotational speed infinitely variable, Citizen R-series of automatic lathes dedicated to small-diameter machining. This machine is used very little (15800 parts cut). model year 2013. With ASP-04 barfeeder. Hjdpfxovtancj Adajh VAT is not needed if the sales happen outside of Turkey.

Condition: good (used), Year of construction: 2001, Ref. -No.: 10617 Manufacturer: KELLENBERGER Type: 600 U Nr. 36 Year of construction: 2001 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175-250 mm Hjdpfxsya Daas Adash Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0 -5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 360° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Micro-corrector of the feed, 1 division of the dial: 0,001 mm / Ø Working speeds continuously adjustable (normal / special): 20 - 400 / 10-400 Max. Grinding length: 900 mm

Condition: used, 3 flanges for type 600 U – available for sale individually or as a set Hedpfx Aox N Rytedash

Condition: good (used), Year of construction: 2001, grinding length: 650 mm, grinding width: 525 mm, total height: 350 mm, table length: 600 mm, table width: 350 mm, Manufacturer: Geibel & Hotz Type: FS 635-Z SA Control: Digital read out Year of construction: 2001 Magnetic table 600 x 350 mm Closed housing for CE Hodpfxjvdal Ao Adaeh Automatic vertical lubrication SA Automatic lubrication Coolant tank Specifications Metric US Standard X - axis 650 mm Y - axis 525 mm Z - axis 350 mm Table length 600 mm Table width 350 mm Table load 400 Feed X - axis 35000 mm/min. Feed Z-axis 1000 mm/min. Grinding stone dimensions 300 x 50 x 76.2 mm Power output 3.7 kW Speed 2800 ? rpm Dimensions (estimate) length 3200 mm width 2000 mm height 2870 mm weight 2300 kg Please note: The information on this page has been obtained from the manufacturer to the best of our knowledge and belief, and where possible, the information is given in good faith but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 1315/451, Completely overhauled: Mechanics, geometry, hydraulics, and electrical parts (checked and/or replaced) Wheelhead: Disassembled, parts cleaned, worn or defective components replaced, motor overhauled, bearings replaced, belts replaced, spindle disassembled, seals and O-rings replaced, adjustments made. Newly painted. Workhead: Disassembled, parts cleaned, worn or defective components replaced, motor overhauled, belts replaced. New spindle bearings. Newly painted. Tailstock: Disassembled, inspected, overhauled. Hydraulics: Disassembled, motor checked, hoses replaced, defective and worn parts replaced. Hydraulic block checked. X-axis: Disassembled, all worn parts such as O-rings, seals, segments, etc. replaced, hydraulic piston overhauled, table ground. Z-axis: Disassembled, table ground, worn or defective parts replaced, hydraulic piston overhauled, newly painted. Electrical cabinet: Completely checked, various relays replaced. Paintwork: Colors: White RAL 9003 and Grey RAL 7011 Geometry according to manufacturer's protocol. Various accessories checked and cleaned. Origin: CH Voltage: 380 / 50 / 3 Net weight: approx. 2,200 kg Customs tariff number: 8460.2920 TECHNICAL SPECIFICATIONS Nominal distance between centers: 600 mm Max. distance between centers (with extended headstock): 750 mm Center height, standard: 125 mm Center height with interchangeable pads for heads: 175–250 mm Max. workpiece diameter (125 mm center height): 250 mm Max. workpiece diameter with interchangeable pads: 350–500 mm Swiveling range of table in each direction: 10° Max. grinding length for flat surfaces (max. width = 200 mm): 900 mm Continuously variable hydraulic table speed: up to approx. 6 m/min Table reversal delay: 0–5 sec Grinding wheel for external grinding, diameter - width - bore: 400x50x127 mm Grinding wheel for flat surface grinding: 250x13x76 mm Hjdpfx Adow U Ry Njajh Wheelhead spindle speed: 1,500/1,700/2,200/3,600 rpm Wheelhead swiveling range: 270°, with indexing every 90° Vertical travel of wheelhead, center height: 125–350 mm Transverse travel of wheelhead: 285 mm Hydraulic rapid traverse stroke: 40 mm Intermittent infeed of wheel by table reversal: 0.001–0.03 mm/dia Continuous infeed for plunge grinding: 0–0.9 mm/dia Micrometric infeed stop, by division: 0.001 mm/dia Workhead swiveling range: 360° Workhead spindle speed, stepless: normal/special: 20–400 / 10–400 rpm Internal taper of workhead/tailstock: Morse 5/3 Wheelhead motor: approx. 4 HP All technical specifications are given without obligation and subject to errors or omissions.

Condition: refurbished (used), functionality: fully functional, machine/vehicle number: 32461/2384, Manufacturing origin Swiss Voltage 380 / 50 / 3 Netweight 4900 lbs Dimensions 121 x 69 inches TECHNICAL DATA Nominal distance between centre 600 mm Max. distance between centres, headstock and tailstock projecting 750 mm Height of centres, standard 125 mm Height of centres by means of raising blocks for work head-and tailstock 175 =ᐳ 250 mm Max. swing diameter with 125 mm height of centres 250 mm Max. swing diameter with raising blocks 350 =ᐳ 500 mm Table swivels each side 10° Max. lenght for surface grinding (width=200 mm) 900 mm Table speed infinitely viable by hydraulic drive, approx. .. 6 m/min Dwell of table reversal 0 - 5 sec. Grinding wheel for cylinrical grinding (diameter x width x hole) 350/400x50x127mm Grinding wheel for surface grinding diameter x width x hole 250 x 13 x 76 Speeds of grinding wheel spindle 1500/1700/2200/3600 Grinding wheel head swivels 270° with indexed stop each 90° Vertical movement of grinding wheel head, height of centres -350 mm Cross movement of grinding wheel head 285 mm Rapid advance and withdrawal of wheelhead 40 mm Intermittent infeed per reversal of table 0,001-0,03 mm/dia Infeed for plunge grinding 0-0,9 mm/dia Micro-corrector of infeed, 1 division of dial 0,001 mm/dia Swivel of work headstock 360° work speeds infinetely viable, normal/special 20-400/10-400 Internal taper of headstock/tailstock 5/3 Morse Grinding wheel motor, approx. 4 HP errors and omissions excepted data given without obligation Inventory Nr.2170089, machine equipped with : 1 Workpiece headstock MT5 1 sinus rule without comparator 1 Wheel headstock with 4 pulleys 1 Tailstock MT3 1 Collet clamping device with drawbar and reduction sleeve B32 1 Internal grinding device with quill Fischer UJ50x250 – pulley Ø 48 for 14000 min-1 1 Pivoting wheel trueing-up device with sole 50 mm 1 Table’s pivoting stop without comparator 1 Cooling device through decantation Hedpfod Amifjx Adajh 1 extractor 1 balancing stake

Condition: like new (used), Year of construction: 2022, operating hours: 850 h, functionality: fully functional, turning length: 610 mm, turning diameter over cross slide: 500 mm, turning diameter: 725 mm, spindle speed (max.): 5,000 rpm, spindle bore: 65 mm, travel distance X-axis: 260 mm, travel distance Y-axis: 80 mm, travel distance Z-axis: 610 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 30 m/min, feed length X-axis: 260 mm, feed length Y-axis: 80 mm, feed length Z-axis: 610 mm, torque: 250 Nm, bar passage: 65 mm, Equipment: documentation/manual, rotational speed infinitely variable, For sale: As-new EMCO MAXXTURN 65-G2 SMY, year of manufacture 2022, equipped with Siemens Sinumerik ONE CNC control featuring ShopTurn! CNC turning center for complete machining of turned/milled parts. Key features include: - Integrated spindle motors, counter-spindle, water-cooled (preloaded roller guides) with Y-axis, operative on main and sub-spindle - Latest SINUMERIK ONE control with ShopTurn conversational programming Main Spindle: - Max. bar capacity: 65 mm - Max. torque: 250 Nm - Speed range: 0–5000 rpm Sub-Spindle: - Drive power: 22 kW - Max. torque: 130 Nm - Speed range: 0–7000 rpm Tool Turret: - 12-station VDI 30 radial turret with directional logic for up to 12 driven toolholders - Max. drive power: 6.7 kW - Max. torque: 25 Nm - Max. speed: 5000 rpm Y-Axis: - Travel: ±40 mm Additional Equipment: - Hollow chuck cylinder incl. draw tube - C-axis for both spindles - Sinumerik ONE / OPERATE control - 22" multi-touch display - ShopTurn, 3D simulation, remnant material detection - USB interface - Electrical cabinet climate control - Coolant system incl. pump (3.5 bar) - Chuck flushing (extra pump 3.5 bar) - Parts ejector and flush through sub-spindle - Hydraulic unit - Interface for chip conveyor - Documentation and CE certificate - Control languages: German / English - Electronic handwheel - EMCO TOOL BREAKAGE AND WEAR MONITORING / SINUMERIK ONE - Alternating spindle speed - Sub-spindle as tailstock: This cycle allows use of the sub-spindle with mounted live center for workpiece support, permitting shaft machining even on machines without a conventional tailstock. Max. support force limited to 50% of maximum axis force. - EMCO PROFI-NET ROBOTIC INTERFACE: Connection interface for robot integration via HARTING connector. Signal exchange via Profinet. Safety signals: 2-channel/potential-free. - Digitalization package for Sinumerik: Condition monitoring - SIEMENS ONE INTERFACE for connection to MDE/BDE systems. Standard info includes: • Machine on - AUX ON Hsdox E Dncspfx Adaeh • Automatic mode • Production mode - program active • Program running and override between 95–105% • Part count pulse (M30) • Programmable pulse (M300) - 3D machine data / MT65-G2: 3D model of the machine included Pneumatically actuated finished parts catcher for gentle unloading of finished components. Parts are transported to a collection box (standard) or onto a conveyor belt (optional). - Max. finished part length: 175 mm - Max. finished part diameter: 65 mm - Max. finished part weight: 4.5 kg INTERFACE SL1200 HT65-DT/TT + MT65-1000: For connecting the EMCO SL1200 bar feeder. Etc. The machine is immediately available!

Condition: reconditioned (used), KELLENBERGER 600 U 175 is a cylindrical grinder of high precision, offering accuracy and reliability. Capacities: centre height 175 mm, between centres 600 mm; wheel Ø350×50 mm, bore 127 mm; wheelhead 270°. Specs: wheel speeds 1500–3600 t/min (4 steps); work spindle 20–400 t/min (stepless); table tilt 10°, up to 6 m/min; supply 3×380 V 50 Hz; wheel motor 4 CV; weight ≈2200 kg; dims 3000×1750×1600 mm. Accessories: digital readout (2 axes), tailstock fine adjust, internal grinding attachment, wheel guard, safety device, sliding door. Suited to tight tolerances in automotive, watchmaking, machine tools, aerospace and medical sectors. Hsdpfx Adsxx U H Tjaeh

Condition: used, Year of construction: 1986, grinding diameter 350 mm grinding length 600 mm centre height 175 mm Very well maintained machine. The machine comes from a precision grinding shop from the Black Forest. Can still be viewed under power for a short time at the seller's premises. Hedsv Tqqnepfx Adaoh In 2022, the machine was partially overhauled and serviced in-house with production of the geometry according to the manufacturer's protocol. Equipment: -2-axis digital readout FAGOR -sine bar -tailstock with fine adjustment -Hydraulic tailstock -Surface grinding device -Internal grinding device -Fischer UJ70 internal grinding spindle -Paper belt filter -automatic sequence: roughing-finishing-firing-retur Translated with (free version)

Condition: good (used), Year of construction: 2008, grinding length: 1,250 mm, table length: 1,250 mm, table load: 1,200 kg, table width: 500 mm, spindle speed (max.): 2,600 rpm, spindle speed (min.): 1,000 rpm, overall weight: 9,300 kg, travel distance X-axis: 1,400 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 600 mm, power: 185 kW (251.53 HP), input voltage: 400 V, space requirement height: 2,870 mm, Equipment: rotational speed infinitely variable, X-axis: grinding length 1,250 mm, travel 1,400 mm Y-axis: distance from table to spindle center 700 mm, travel 600 mm Z-axis: grinding width see note, travel 600 mm Note: The grinding area in the transverse direction (Z-axis) depends on the travel path Hjdpfx Aju Hiq Rodaoh and the grinding wheel width. Example: Travel path across = 600 mm Grinding wheel width 60 mm = grinding width 660 mm Grinding wheel width 100 mm = grinding width 700 mm See pictures for more technical data

Condition: used, internal diameter 340/440 mm grinding depth 99999 mm grinding diameter 250,350,450 mm grinding length 600 mm centre height 125,175,225 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±10 ° longitudinal feed of the table 900 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,2 t dimensions of the machine ca. 3,1 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your metrical overhauled and repainted with: -Neuem CE konformem Schaltschrank. -Neuem Werkstückspindelmotor und Regler in Drehstromtechnik. -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my Hsdpfxjd Ih Dxj Adash Optionen: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: -Bedienwerkzeug -Spannrohr für Futter weiteres Zubehör auf Anfrage. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.