Screw compressor S016003

Kaeser ask40

Condition: like new (used), Year of construction: 2026, operating hours: 3 h, available immediately: Kaeser ASK 40 T - 11 bar screw compressor with integrated cold dryer with Controller SIGMA CONTROL 3 Year 2026 Operating hour: 3 h Pressure: 11 bar Nominal power: 22 kW Delivery rate: 3.50 m³ / min Ijdpfx Aoyw Nurjkxjtf Sound level: 69 dB (A) Compressed air outlet: 1 1/4" Dimensions length x width x height: 800 x 1460 x 1530 mm Weight: 620 kg Visit our store. We always have a large selection of new and used compressors in stock!

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t Iedpfod Iipmex Akxotf dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens

Condition: used, Year of construction: 2003, functionality: limited functionality, machine/vehicle number: 0 278 06 1192, film width: 700 mm, roll diameter: 700 mm, Used Friz rotary cutter. 1 set of blades has been resharpened. The machine is used and is sold without warranty. Inspection is possible and welcome. Itedov Radxjpfx Akxef Loading facilities available.

Condition: good (used), Year of construction: 2020, operating hours: 1,730 h, functionality: fully functional, overall weight: 580 kg, total length: 1,335 mm, total width: 750 mm, total height: 1,880 mm, pressure (max.): 11 bar, ambient temperature (min.): 3 °C, ambient temperature (max.): 45 °C, noise level: 66 dB, protection type (IP code): IP55, Equipment: documentation/manual, refrigerant dryer, type plate available, Kaeser Aircenter SK22 Screw Compressor (2020) Manufacturer: Kaeser Type: Aircenter SK22 Year of Manufacture: 2020 Condition: Very good, used Run-on hours: 6,000 h Load hours: 1,730 h Maintenance in 2,589 h Iedpfxjxnnd De Akxetf Technical Specifications Pressure 11 bar Effective free air delivery 1.67 m³/min Rated motor power 11 kW Motor protection class IP 55 Power supply 400 V / 3 Ph / 50 Hz Dimensions (W x D x H) 750 x 1,335 x 1,880 mm Weight 580 kg Air receiver 350 l Compressed air connection G 1 Sound pressure level 66 dB(A) Refrigeration dryer Power consumption 0.49 kW Pressure dew point 3 °C Pressure drop 0.06 bar Refrigerant R 513a Energy-saving control: Yes Electronic condensate drain: Eco-Drain Electrical equipment: EN 60204-1: Yes Scope of delivery: – Complete original documentation – RFID cards (2x) – 5m power cable with 32A plug

Condition: new, Fastech horizontal bandsaw semi-automatic BMSY 360 DGH ECO Round cutting range mm: 360 Flat cutting range mm: 510 x 360 Square Cutting range mm: 360 +30 ° Round cutting range mm: 360 +30 ° Flat Cutting range mm: 440 x 360 +30 ° Square Cutting range mm: 360 +45 ° Round Cutting range mm: 360 +45 ° Flat cutting range mm: 390 x 360 +45 ° Square cutting area mm: 360 +60 ° Round cutting range mm: 200 +60 ° Flat cutting range mm: 200 x 360 +60 ° Square cutting range mm: 200 -30 ° Round cutting range mm: 360 -30 ° Flat cutting range mm: 440 x 360 -30 ° Square cutting range mm: 360 -45 ° Round cutting range mm: 360 -45 ° Flat cutting range mm: 390 x 360 -45 ° Square cutting area mm: 360 -60 ° Round cutting range mm: 260 -60 ° Flat cutting range mm: 260 x 360 -60 ° Square cutting range mm: 260 Engine power main drive kW 3 Hydraulic pump power kW 0,37 Engine power coolant pump kW 0,12 Band speed, infinitely variable: m/min.20 - 100 Saw band dimensions mm: 4800x34x1,1 Working surface height mm: 860 Itedpfsg Ekttsx Akxjf weight kg: 1450 length / depth / height mm: 2650 / 1210 / 1870 Double mitre saw Infinitely variable belt speed hydraulic vice High performance gearbox Hydromechanical saw band tensioning Saw band brush Digital display for mitre angle

Year of construction: 2006, condition: good (used), FIN Glue spreader SC2R/1300 with 2 rollers The year 2006 manufacture: FIN s.r.l. Italy main technical specification: Width of working: 1300mm The maximum passage between roller: 120mm The diameter of rollers: 185mm Advancement speed: 19m/min Net weight 390 Kg Overall dimensions: 64 x 210 x 136cm Overall dimensions with case: 73 x 200 x 153cm 400 V, 50 Hz, 037 kW Accurate and uniform spreading with any type of glue, excellent technical characteristics, added to the high practicalness, functionality and safety for the operator, place it at the forefront among the 2 roller glue spreaders. Spreading roller covered in antiacid rubber, ground and furrowed, hard wearing, as they are built with a rational layer of rubber it is, therefore, possible to carry out 6-7 grindings. It is easy and quick to disassemble. Spreading, precise and uniform on one or both sides of the panels. Special shock-absorbers, on the roller supports, allow the rollers an automatic opening depth, so as to spread panels of different thickness within 5 mm. they also compensate for Isdpfx Akjfguntexstf eventual parallelism differences of the panel. Uniform glue dosing by a rectified distribution tank, in sheet-iron, with very quick extraction to allow cleaning. Collecting tank, for glue and washing water, in galvanized sheet-iron, extractable for easy cleaning. Safety protections, in sheet metal on the rollers and glue distribution tank, a sheet metal protection prevents the introduction between the rollers of any object more than 5 mm. thick over the transit established, ensuring the maximum safety for the operator. Electrical installation, in a waterproof case with fuses, thermal switch for motor and transformer protection. Control panel, with starting button, stopping button and warning light (24 V). Rollers rotation chain with self-registrable turnbuckle pinion. Roller washing with a bored washing tube, for the water intake during this operation.

Year of construction: 2021, condition: new, Fastech horizontal band saw BMSO 350 GA Cutting capacity (round) mm: 350 Cutting capacity (rectangular) mm: 400 x 350 Cutting capacity (square) mm: 350 x 350 +30° Round cutting range mm: 320 +30° Flat cutting range mm: 400 x 350 +30° Square cutting range mm: 350 +45 ° round cutting range mm: 320 Isdog Ekt Nepfx Akxjtf +45 ° flat cutting range mm: 290 x 300 +45 ° square cutting range mm: 290 x 290 Engine power main drive kW: 2,2 Hydraulic pump power kW: 0,37 Coolant pump power kW: 0,12 Band speed, infinitely variable mm: 20-100 saw band dimensions mm: 4160x34x1,1 working surface height mm: 760 weight kg: 1050 length mm: 2450 depth mm: 920 Height mm: 2020 roller conveyor 1200mm infinitely variable belt speed hydraulic vice High performance gearbox Hydromechanical saw band tensioning Saw band brush Control system

Condition: used, pressing force: 65 t, table width: 1,100 mm, table length: 2,200 mm, total length: 2,600 mm, total width: 1,300 mm, total height: 2,000 mm, overall weight: 2,800 kg, empty load weight: 2,800 kg, cylinder diameter: 80 mm, opening width: 300 mm, plate width: 1,100 mm, space requirement height: 2,000 mm, space requirement length: 2,600 mm, space requirement width: 1,300 mm, transport length: 2,600 mm, transport width: 1,300 mm, transport height: 2,000 mm, No. 04486 Veneer press Ott JU 60 Used Heating plates 2200 x 1100 mm LW Plates gold anodized, in very good condition Electric heating 2x 6 kW 4 hydraulic cylinders, diameter 80 mm each Total pressing pressure 65 tons Specific pressing pressure at full capacity 2.7 kg/cm2 Opening width 300 mm Button control for close - open - stop Circumferential emergency stop safety pull cord Transport dimensions approx. 2600 x 1300 x 2000 mm LWH Weight approx. 2800 kg To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical specifications, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Itjdpfx Akeyfw D Asxof Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex warehouse

Condition: excellent (used), Year of construction: 2022, IES screw compressed air units supply a continuous, reliable flow of compressed air directly to the point of use without requiring a dedicated room. The ECB – SCB range, made according to high quality standards, uses components by leading companies on the market, ensuring reliability and traceability. 7.5 KW 8 Bar 1000 lts/min Ijdpjxaxr Nsfx Akxetf Very low running hours - 1351 run hours Complete with three filter set

Condition: refurbished (used), functionality: fully functional, Refurbished six-piston hydraulic platen press of Italian manufacture. Branded multi-layer press designed for easy wood veneering, supplied with warranty and service support. Veneering plate dimensions: 3000 x 1300 mm Pressure at full surface: 2.2 kg/cm² Total maximum pressure: 80 tons Number of hydraulic pistons: 6 Teflon MYLAR film on the plates Piped for water-based heating of the plates Option to install a hot water boiler Price includes a fully refurbished machine Price: 10,000 EUR excl. VAT Ijdpfxovvbbco Akxstf The machine will be refurbished, set up, and tested. The refurbishment status and machine readiness for collection must be confirmed in advance! In stock at Telnice near Brno, Czech Republic Testing, demonstration, and operator training included as standard.