Edge banding machine

HOMAG Profi KAL310

Condition: used, machine/vehicle number: 007134, Type of edging: Thin edge, Thick edge, Solid wood Dsdpfxjt Hmtze Afnsul Gluing System: EVA Hotmelt, Hot Air Premilling Unit: yes Corner Rounding Unit: yes Grooving Unit: yes Max feed speed: 25 m/min Maximum panel thickness: 60 mm Operating Units: 10 nr

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, Fully working UniControl 12 year 2006 from Norway - for exact technical specification please open attached document in PDF below. Cross section UniTec 12: - saw unit - edge round cutter from bottom - Hubspindel no.1 - Hubspindel no.2 - Hubspindel no.3 Long , profile section UniVar 12: - Profil cutter Duodpfomgc I Njx Afnsl - Profil cutter - Profil cutter horizontal - Profil cutter - Profil cutter - Profil cutter Total el power 114 kw 400 V AC Need for suction 270 m3/min Need of compressed air 1000 L/ minMachine was in use until 15.08.2023 Payment: Prior to loading Delivery: ex. factory Rendalen - Norway Machine is located in Norway ( near to Trondheim) The machine is now disconnected, stored in dry and warm wearhouse, and are ready to be shipped. Rekman Maskin & Service - service of woodworking machines since 1986.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Line of two Homag edgebanders KAL 310/09/A20 and 330/09/A20/WZ 90KW with return system. Machine in excellent condition. Can be inspected in department 14. Dismantling, loading, and transport at the buyer's expense. Djdpow A R R Esfx Afnoul

Condition: excellent (used), UNLOADER (SINGLE-CAGE) - Vacuum system with its pump - Top holding bar deplacement (pivoting) of 180° - Horizontal-longitudinal bars (rocker arms) for the vacuum cups supporting - In-side lifting table, surface with motorized-rollers - Front-side sliding door (or metal grid) to out-feed the stack of the panels Dsdpfxscggy Sj Afnjul - Separated electric and command panel - Out-side rollers way (on ground) to out-feed pile of panels from the Unloader - Out-side motorized rollers table (which brings panels to the Unloader), with also cross motorized conveyor belts (at 90°) - Working capacity (cycles/min): 12-15 - Min/Max panels thickness mm 10 - 40 - Min dimensions of the panels mm 250 x 320 (estimated) - Max dimensions of the panels mm 1200 x 3000 - Total installed motor power KW 10

Condition: used, Year of construction: 2013, 3D-Venjakob Perfect Air Jet painting line: - Manufacturer: Venjakob - Year of construction: 2013 - Working width: 1.300mm - Max. part length 6.500mm - In U-shape with angle transfer Consisting of: 1. loading belt, length 3,050mm 2. free space für Sanding machine (only optional, not included in the price) 3. spraying machine VEN SPRAY PERFECT, length 5.510mm 4. flash-off dryer OIR, length 6,000mm 5. nozzle dryer VEN DRY AIR JET, length 4,160mm 6. angle transfer 180 degrees, with nozzle dryer Dujdpfx Aju Afu Refnel 7. nozzle dryer VEN DRY AIR JET, length 5,160mm 4pcs. IR tubes 8. nozzle dryer VEN DRY AIR JET, length 5,160mm 4pcs. IR tubes 9. nozzle dryer VEN DRY AIR JET, length 5.160mm 4 pcs, IR tubes 10. 3D UV dryer, VEN DRY UV, GA + HG 11. removal area, belt of the UV dryer Further information: On request

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Vacuum system (with its pump) No. 2 Vertical supporting columns of the top supporting beam No. 1 Horizontal top supporting beam (where the carriage slide on) No. 1 Motorized sliding carriage with horizontal metal arms Dusdpfxofi Tg He Afnol No. 2 Out-side rollers way (on gound) to in-feed pile of panels to the Loader Out-side motorized rollers table (which receives panels from the Loader) Separate electric and command panel Perimetral safety metal grids Working capacity (cycles/min) 16 (ca.) Min/Max panels thickness mm 10 / 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1300 x 3000 (ca.) Total installed motor power Kw 30

Condition: excellent (used), PANELS RETURN SYSTEM for EDGE BANDER (Right) To combine with a single-side Edge Bander allowing the operator (worker) to always stay at the in-feed side of the machine (the processed workpiece will automatically return-back to him). Blowing Air Table, infeed and outfeed (total dimensions mm 3520 x 2560) Djdjff R Tqspfx Afnoul 180° transfer (mm 3120 x 2140) with motorized roller conveyors and motorized belts Motorized carpet (mm 9080 x 1560) Panel Dimensions (MIN/MAX): Length - 240 mm / 2800 mm Width - 120 mm / 1300 mm Thickness - 8 mm / 60 mm opt. up to 100 mm

Year of construction: 2011, condition: used, functionality: fully functional, Finger jointing line for cross sections up to 200 cm² (80/240 mm or 100/200 mm), with the following. components: 1. HOWIAL tilt unstacking - SH/4t - 1,75x1,75x6,00m - 4t - short. Length 2,50 m, semi-automatic separation of the package. For tilting the wood pile up to 45°. Electric motor drive. stack dim. max. 1,75 x 1,75 x 6,00 m max. stacking load 4 t shortest wood length 2,5 m 2. HOWIAL - VE 1 lamella separator for crosscut saw. With pneum. controlled tongues, on which the material is marked for defects, deposited on the roller conveyor below. 3. HOWIAL - evaluation roller conveyor RO-1 digital wood moisture measuring, control and recording system for autom. recording and control of wood moisture in cycle measuring method according to electric resistance principle. 4. gann DMT-8 dig. Wood moisture measuring, control and recording system for automatic detection and control of wood moisture in the cycle measuring method according to the electrical resistance principle. Plant in large switchboard complete with ink jet printer. 5. HOWIAL - crosscut saw AS-30 B pneum. Under table crosscut, with 2 autom. feed units, autom. crosscut. Special photocell control for detection of fluorescent line markings. Automatic waste disposal possible. Saw motor power 7,5 kW saw blade diameter 700 mm feed drive approx. 2 x 1,5 kW Air pressure 8 bar feed speed max. approx. 60 m/min. 6. HOWIAL - conveyor belt cut off waste, with studded belt and guide plates belt width 350 mm belt 2000 mm long belt speed 0,4 m/sec. 7. HOWIAL - double roller conveyor RO-2 6,00 m long incl. transversal transport, drive by round belt, all rollers driven. Cross transport chain conveyor. Ejection ± moisture right Transport speed adjustable 100 m/min. length approx. 6,00 m Width of rollers approx. 400 mm Diameter 112 mm 8. compact finger jointing machine Cook Bolinder The technical data are original from Cook Bolinder: wood width from 75 to 245 mm Timber thickness from 20 to 105 mm Input lengths from 1m to 6 m Cross sections from 30 cm² to 200 cm² Pressing force 5 - 22 to Spindle diameter 50 mm tine profile 15/15 spindle speed approx. 6000 upm Total electrical connected load approx. 62 kW Machine weight approx. 9 to. Gluing OEST comb system for PU Modern Telemechanique SPS control. 9. HOWIAL - Roller conveyor with destacking system Driven roller conveyor with autom. ejector and hydr. driven destacking arms. Dedpoi Ezx Dsfx Afnsul Technical data: H: 920 mm L: approx. 12.000 mm 10. safety fences incl. circuit breaker 11. finger joint testing machine BSPLT-100 Testing machine for finger joint bending test according to DIN 1052-1/A1 and EN 385 Support distances freely adjustable, attached dimension scale, autom. calculation of support distances in the software. Fully automatic test procedure by mouse click on PC (not included). Alternatively, the test procedure can be started by key operation on the front panel. Connection of any commercially available PC or laptop (Win 2000/XP) via the supplied RS232 serial cable. Fully automatic measured value logging as well as automatic logging in MS-Excel with graphical display. Representation max. wood width: 300 mm max. wood thickness: 140 mm max. compression force: < 100 kN max. support length: 2100 mm Measuring accuracy WITHOUT DISMANTLING

Condition: good (used), Year of construction: 2014, Used carcass press - GANNOMAT Concept 70 Eco - Year of manufacture: 2014 - Available December 2025 Dsdpfx Asxhc T Tofneul

Condition: used, Year of construction: 2010, Touch screen control for adjusting work groups Panel height mm from 10 to 50 Solid wood 12 mm Pvc/Abs mm from 0.4 up to 3 Feed speed up to 22 m/min Minimum panel length 150 mm Minimum panel width 70 mm Working height adjustable electronically by C.N. Motorized rubberized belt with superior pressure Panel support guide Side roller conveyor with idle wheels for panel support Anti-adhesive group Rectifier group with two motors of 1.5 KW each Reel holder plate COMBIMELT gluing unit for hot melt glue with automatic dosing VarioMelt with pre-melter Patented edge pressure unit with segmented pads Trimming unit with 2 motors Gleaning unit with 2 motors Rounding unit Edge scraper unit Installed power KW 13.7 Machine length mm 6170 approx Dodpfx Ajpzfcgjfnjul TECHNICAL DETAILS TO BE CHECKED