Lapping Machine

Hahn+Kolb ZL 800 H

Condition: used, Year of construction: 1975, table diameter mm workpiece height mm number of wheels 2 total power requirement 11 kW weight of the machine ca. 4,2 t dimensions of the machine ca. m Iaodpfx Ahjub Al Ijvsp

Condition: used, Year of construction: 2017, operating hours: 300 h, functionality: fully functional, total width: 2,160 mm, total length: 1,350 mm, total height: 1,700 mm, pressure: 2,500 bar, operating pressure: 2,500 bar, fuel: diesel, overall weight: 1,850 kg, rotational speed (max.): 1,800 rpm, high-pressure hose length: 20,000 mm, empty load weight: 1,850 kg, fuel tank capacity: 140 l, type of cooling: water, power: 120 kW (163.15 HP), water pressure: 2,500 bar, pump capacity: 25 l/min, Equipment: crane, type plate available, CD160-2500 with 2500 bar and 25 l/min. The pump is powered by a water-cooled 4-cylinder SISU diesel engine. The entire frame is made of hot-dip galvanized steel, ensuring long durability and corrosion resistance. The frame is equipped on all four corners with rubber feet, forklift pockets, and lifting eyes. The machine features a galvanized roof plate with a side mount for the protection and storage of, for example, high-pressure hoses. Similar to but not a Dynajet, Falch, Hammelmann, Kamat, Uraca, Woma, etc. General Specifications: Operating pressure: 2500 bar Flow rate: 25 l/min Max. pump speed: 560 rpm Drive engine: 4-cylinder SISU diesel Drive engine output: 119.3 kW Drive engine speed: 1800 rpm Iedpfexufbtex Ahvoap Tank: 140 L Max. fuel consumption: 26 L/h Dimensions and unladen weight (SKID): 2160 mm x 1350 mm x 1700 mm (1850 kg) Standard accessories included.

Condition: ready for operation (used), Year of construction: 2006, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, spindle speed (max.): 18,000 rpm, This 5-axis HERMLE C30U + RS Automation was manufactured in 2006, offering advanced capabilities for precision machining. Ideal for complex geometries, this vertical machining centre represents a significant asset for enhancing your production efficiency. Consider the opportunity to buy this HERMLE C30U vertical machining centre. Contact us for more information. Additional equipment • Tool Magazine: Additional magazine ZM157 • Tool Breakage/Measurement: BLUM tool breakage/measurement • Measuring Probe: Heidenhain • Event Messenger: Available • Electrical Heat Compensation: Provided • External Blowing Air: Provided / Oil Mist Extraction: Provided / Chip Trolley: 450 liters • Rotating Transparent Window: Available • Additional Accessories: Manual control module, flange for extraction 1, bed flushing, sealing air for scales, machine license TCS-Soflex Machine Benefits Technical Machine Benefits • Nc swivel rotary table: diameter 280 mm • Table axis: a-axis off-center / table specification: 6-way rotary feedthrough • Spindle hours: approximately 50000 hours Iedpfx Ahox D Ew Hevjap • Internal coolant supply: 80 / filter: paper belt filter / conveyor: scraper belt conveyor / automatic cabin door: yes • Polycarbonate safety glass: windows / frequency: 50 hz • Rs automation Technical Specification Taper Size SK 40

Condition: like new (used), functionality: fully functional, Year of construction: 2017, operating hours: 2,600 h, control type: CNC control, controller model: Fanuc 32 C, Equipment: documentation/manual, Standard programs such as parameter settings Dressing settings Speed settings Program management settings Limitation of travel distances x + y Basic parameter settings Grinding wheel management program Warming-up cycle program Surface plunge grinding program Measuring program 15 kVA transformer Full enclosure Meister G3 Spindle upgrade to 3.7 kW, disc 225 mm ETHER interface for network connection Control module with extended memory Fanuc Macro B option Program creation for batch programs Programmable spindle speed WinWop program for contour creation (Windows) WINWop program for error compensation Iedow I Tt Sjpfx Ahveap WinWop postprocessor CGS Complete Grinding Solutions software Option Dressing Swiveling profile dressing device Diamond dressing wheel Pre-dressing device VPA 100 L Diamond wheel 100 mm for pre-dressing device Regrinding package diamond wheel G3 / W Option – Clamping and Balancing Magnetic chuck 400 x 200 400 mm stop bar with prism Fully automatic balancing device, size 1 Grinding wheel flange for G3, bore 51 mm Option Filter Systems Belt filter system 175 l Extraction unit for emulsion mist 500 Inquiries only from Europe, preferably the EU.

Year of construction: 1999, condition: excellent (used), Control system: CNC-controlled and manual operation PC P 2000 MMX-PCI Desktop ATX 15" color display, keyboard CNC-Turbo Roughness for WINDOWS TECHNICAL DATA Granite test plate (DIN 876) Length x Width 1200 x 500 mm Accuracy grade Grade 2 Flatness: 16.6 µm Weight 250 kg Linear traversing unit Waveline 60 Basic Measuring stroke 60 mm Resolution 0.014 µm Measuring column Wavelift 400 CNC Travel distance 400 mm Positioning repeatability < 10 µm Ijdolxyp Hopfx Ahveap Machine dimensions (W x D x H) 1.8 x 0.8 x 2.2 m Weight 600 kg EQUIPMENT/ACCESSORIES  Complete enclosure with electrically operated roller shutters  Granite plate 1200 x 500 mm  ISEL feed axis with ball screw  Workpiece support plate  Linear feed unit Waveline 20/60  Measuring column Wavelift 400 CNC  Tilting unit KEG 60 on the measuring column, manual for Waveline  Built-in kit for roughness measurement  Built-in kit for contour measurement  Various probes and holders for roughness and contour measurements  Machine table  Emergency stop button on the machine table  Calibration set  Support prisms  Maintenance unit for compressed air preparation  Air damping elements for supporting the granite plate  Documentation

Condition: used, functionality: fully functional, Used Schenck Balancing Machine HU 9 T with used CAB 690 H measuring unit. The machine comes with original foundation drawings, documentation and manuals. The machine can be test run in Kerava. Technical data: - Maximum rotor weight with roller bearings: 50 000 kg - Maximum weight for symmetrical rotor: 56 000 kg - Load capacity per bearing pedestal: 28 000 kg - Load capacity per T-slot pedestal: 28 000 kg - Minimum rotor weight: 2 500 kg (1000 kg) - Maximum diameter over machine base: 4 000 mm - Machine bed length: 15 000 mm - Adjustable roller bearing diameters: 125–270 mm , 450–900 mm - ABB electrical drive FC: 90 kW - 4-speed gearbox: approx.120–1400 rpm - Pneumatic locking for end drive - Electrically operated movable pedestals - Accuracy: Umar 0,5gmm /kg 270 rpm 1000 gmm Iaodpfxsw Aaugj Ahvsp

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 1315/451, Completely overhauled: Mechanics, geometry, hydraulics, and electrical parts (checked and/or replaced) Wheelhead: Disassembled, parts cleaned, worn or defective components replaced, motor overhauled, bearings replaced, belts replaced, spindle disassembled, seals and O-rings replaced, adjustments made. Newly painted. Workhead: Disassembled, parts cleaned, worn or defective components replaced, motor overhauled, belts replaced. New spindle bearings. Newly painted. Tailstock: Disassembled, inspected, overhauled. Hydraulics: Disassembled, motor checked, hoses replaced, defective and worn parts replaced. Hydraulic block checked. X-axis: Disassembled, all worn parts such as O-rings, seals, segments, etc. replaced, hydraulic piston overhauled, table ground. Z-axis: Disassembled, table ground, worn or defective parts replaced, hydraulic piston overhauled, newly painted. Electrical cabinet: Completely checked, various relays replaced. Paintwork: Colors: White RAL 9003 and Grey RAL 7011 Geometry according to manufacturer's protocol. Iasdpfx Ahew U Ry Novep Various accessories checked and cleaned. Origin: CH Voltage: 380 / 50 / 3 Net weight: approx. 2,200 kg Customs tariff number: 8460.2920 TECHNICAL SPECIFICATIONS Nominal distance between centers: 600 mm Max. distance between centers (with extended headstock): 750 mm Center height, standard: 125 mm Center height with interchangeable pads for heads: 175–250 mm Max. workpiece diameter (125 mm center height): 250 mm Max. workpiece diameter with interchangeable pads: 350–500 mm Swiveling range of table in each direction: 10° Max. grinding length for flat surfaces (max. width = 200 mm): 900 mm Continuously variable hydraulic table speed: up to approx. 6 m/min Table reversal delay: 0–5 sec Grinding wheel for external grinding, diameter - width - bore: 400x50x127 mm Grinding wheel for flat surface grinding: 250x13x76 mm Wheelhead spindle speed: 1,500/1,700/2,200/3,600 rpm Wheelhead swiveling range: 270°, with indexing every 90° Vertical travel of wheelhead, center height: 125–350 mm Transverse travel of wheelhead: 285 mm Hydraulic rapid traverse stroke: 40 mm Intermittent infeed of wheel by table reversal: 0.001–0.03 mm/dia Continuous infeed for plunge grinding: 0–0.9 mm/dia Micrometric infeed stop, by division: 0.001 mm/dia Workhead swiveling range: 360° Workhead spindle speed, stepless: normal/special: 20–400 / 10–400 rpm Internal taper of workhead/tailstock: Morse 5/3 Wheelhead motor: approx. 4 HP All technical specifications are given without obligation and subject to errors or omissions.

Condition: new, PAK-1 Unbalance Measuring Unit is designed to modernize your balancing machine. A balancing machine has a long mechanical life, but prolonged use leads to gradual failure of electronics and measuring instruments, causing problems with spare parts and lack of technical support. Minimize downtime and ensure the reliability of your balancing machine by upgrading it with a new advanced measuring unit. The PAK-1 unbalance measuring unit works in all balancing machines of most existing designs and manufacturers. Confidence in results and ease of use: Easy to set up and work with, our devices do not require any special theoretical knowledge. Wide range of functions for your balancing machine: The use of modern microprocessor technology and many years of experience of our developers allows us to implement functions that were previously unavailable to other manufacturers. Your machine complies with ISO 21940: Balancing machines equipped with the PAK-1 unbalance measuring unit fully meet the precision requirements of modern standards. HIGHLIGHTS • We make balancing easier - the main advantage of our balancing systems. • The balancing process is displayed in real time and the unbalance behaviour of the rotor is monitored on the screen to achieve the best possible result. • The maximum sensitivity of the machine at any moment of operation, the set-up and calibration of the machine is carried out by the operator himself. • Free from the influence of external vibration factors on the measurement result, it has a high degree of protection against various types of interference. • Easy to learn working skills and maintenance for any employee. INCLUDES: 1) vibration sensor signal processing unit, 2) fanless industrial computer with touch screen, 3) new vibration and speed sensors, 4) metal protected cable set. SEQUENCE OF WORKS for modernization of the measuring unit - Replacement of the existing measuring system with the balancing complex PAK-1 based on an industrial computer; - Installation of new vibration sensors and rotor speed sensor - Replacement of all connecting cables; - Adjustment of the measuring unit on the balancing machine; - Training of personnel with skills to operate the machine. VTM GROUP offers to upgrade your balancing machine. We repair and modernise various old balancing machines of all types from all manufacturers. It's cost effective. An alternative to buying a new balancing machine in 95% of cases. Urgent. Iajdpfxsq Ttn De Ahvsp Work can be done at customer site within 1-2 days. New components for modernization of your machine: • Installation of new measuring system and vibration and speed sensors. • Installation of new electrical equipment • Manufacturing or repair of the rotation drive • Manufacturing of new rollers Every business is different. Let's discuss your task. We can offer a solution for any balancing machine. Please contact us to get the best offer! 👇

Condition: ready for operation (used), functionality: limited functionality, disc diameter: 525 mm, Weight approx. 1,900 kg Dimensions (LxWxH) approx. 1,800x1,500x2,200 mm Working disc diameter 525 mm Largest disc ring width 175 mm Largest workpiece dimension 170 mm Speed of the working disc 45/70/90/140 rpm Main drive performance 4.0 kW Iaedpfjh Invrjx Ahvep Connection 400V/50Hz Emergency stop switch Conventional control with control panel Full-fledged lapping machine, conventional control

Year of construction: 1992, condition: used, grinding height 50 mm grinding width 120 mm grinding wheel diameter 600 mm total power requirement 85 kW weight of the machine ca. 9500 kg D I S K U S (Germany) CNC Controlled Double Sided Vertical Spindle Surface Grinder with Rotary Workpiece Feed System and IONIC Size Control Model DDS 600 III PLM - CNC Year 1992 erial No. 7924 _____ Grinding wheel Ø x bore x height, each 600 x 150 x 75 mm Approximate Workpiece dimensions: Grinding height, approx. 1.5 – 50 mm Grinding width, appox. 20 - 120 mm Vertical quill adjustment, each, approx. 150 mm Infeed of grinding wheels via CNC 0.0001 mm Feed of workpiece transportation device, infinitely variable 40 – 235 mm/sec Grinding wheel speed, each (30 m/s) 191 - 955 rpm Grinding spindle drive, each infinitely variable 37 kW Total electrical load, approx. 85 kW - 380 V - 50 Hz Weight, approx. 9,500 kg Accessories / Special Features * SIEMENS CNC Control, Model SINUMERIK 810 G, with monitor, for 4 axes i.e. * Movement of 2 spindle quills, dressing device, WP Rotation. Direct programming of Grinding Process data on keyboard. In connection with a IONIC Size Control No. 17 A / 68.000 with two tracers for measuring the thickness of the workpieces after grinding process, and corresponding infeed of the grinding wheels. Continuous display of measuring results on the monitor, with statistics, workpiece counter, etc. Digital Display Ampere for both grinding wheel drives and for grinding spindle speeds, etc. . * Positioning control device for supervising the height of the lower grinding wheel.. * Double column design as a portal for extra stability and higher accuracy * Rotary workpiece transportation device with infinitely variable feeds. The workpieces are Manually stacked in a device and forwarded by a transportation carrier disk thru the grinding wheels, there are two WP- down holders, one equipped with a overheight stop-control. * Angled grinding wheel dressing device, with automatic dressing process, integrated in the control as CNC axis, with safety switch-off. * Separate large switch cabinet. * Automatic central lubrication. Large pneumatic control system * Large Coolant device 6 (F) with filtering unit and magnetic separator. * Various Grinding wheels, WP transport carrier disks, 2 flanges, large Olimist separator, etc. Iajdpfxot Hw Nas Ahvjp This machine is very suitable for simultaneous double-sided grinding of large series of workpieces, e.g. punched parts, piston rings, hydraulic parts, rotors, distance rings, etc. Condition : Very good. Machine can be soon inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract.