Bottle Cleaning System

GM Gera GEL3 RV1-230/110-18

Condition: used, Year of construction: 1995, Overview The bottle washer "Sirio 7" from the German manufacturer MAG was built in 1995. Maintenance was carried out regularly by MAG. The machine can be inspected and tested in person. Technical details  Capacity up to 7,000 bph Bottle cells for 1.0 liter bottles (smaller bottles can also be used, but additional insertion plates are required) Diameter of bottles: 78 - 90 mm Bottle height: 288 - 310 mm Bottle cells per row: 10 Dimensions (LxWxH): 7,880 mm x 3,045 mm x 3,325 mm Empty weight: 14,300 kg Full load weight: 25,600 kg Installed power: 20.85 kW Heating system: Steam 3 bar Nlodpjtrbrqofx Af Seg

Condition: used, Year of construction: 2018, Overview  The Gruber AFD6 is a filling machine for bottles and party KEGs that was produced by the German manufacturer Gruber in 2018 and has an operating time of 725 hours. The machine is available immediately. Njdpju I Hr Ujfx Af Selg Technical details - Output - 800 bph (at 0.33l) - 750 bph (at 0.5l) - 600 bph (with 1.0l) - 400 bph (for 2.0l) - 240 bph (with 5.0l party KEG) - Output varies depending on CO2 content and beer temperature (in practice, 1,000 bph could be achieved at 0.33l) - Long tube filler with 6 filling points - Fully automated filling process - Single or double CO2 flushing - Siemens S7 control system with touch panel - Operating hours: 725 hours

Year of construction: 2004, condition: ready for operation (used), Output: 24,000/h, band speed: 0.5m/s, format: 0.25l GASTRO/ 0.5l GASTRO/ 0.7l GBD/ 0.75l GBD, GASTRO, with Sorting System HEUFT SPECTRUM SX TI 36, machines were overhauled in October 2021. Nlsdpfx Afohix Uks Sjg

Condition: used, Year of construction: 2024, Overview The bottle washer was previously used in a brewery. Due to the low number of operating hours, the machine is in very good condition, like new. It was replaced, as the previous owner wanted to run bottle formats, which did not fit this machine. All basins and the machine body are made of stainless steel. The machine is already disassembled and dry stored, so that it can be easily loaded and transported. The machine comes with 12months warrantee. Njdevrfivspfx Af Selg Tech Specs: - Capacity: 9,500 bph - Cell Pitch: 95 mm - Bottles per row: 25 - Dimensions + Weights: Housing: 7,162 x 2,740 x 2,500 mm / 18,806 kg Ready for operation with attachments: 7,162 x 3,540 x 2,730 mm / 31,563 kg - YOM 2024 - Formats: - 0,25l - 0,33l - 0,5l - 0,75l The Machine in Detail / Equipment Features: - Heated by steam - Pre Cleaning and removal of residual liquids by pulsed rinsing prior to washing - CE certified - Chemical Dosing Pumps - Machine data sheet included - High pressure pre rinsing - Rotating Spray nozzles - Single End Machine - Label discharge rear right - Finger discharge + finger feed - Bottle cells made of plastic - Concentration measurement - NaOH supply liquid - Sectional view arrangement of baths - Spindles SST - 24 volt control voltage - Control Siemens S7 - Regularly maintained - Full machine body in SST - Vapor Discharge - Machine dismantled, ready to ship - Automated machine Startup

Condition: new, Year of construction: 2025, Fully automatic cardboard box former for more efficient packing processes. The cartons are automatically removed, built up and taped at the bottom (in only one direction). The constructed boxes will then feed out to a collecting table to fill. - Specifications: PLC and touch screen by SIEMENS; size of boxes in mm: L(350-650)xW(150-500)xH(100-500); max. speed of the machine in neutral: 9 cycles/minute; power: 110/220V, 0.3kW; compressed air: 5-6bar, 0.4m³/min; tape width in mm: 48/60/75; machine dimensions and weight: L2200xW1900xH1450mm, 530kg. Nedpfx Asv Nkviof Sjlg Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.

Condition: ready for operation (used), Year of construction: 2008, A complete filling line from filler to packer is available. Format: Gable top/pyramid pack 0.50l/0.75l/1l, output: approx. 7000 packs/h, dimensions X/Y/Z: approx. 9500mm/3200mm/3500mm, weight: approx. 13000kg, operating hours: approx. 32500h. Applicator: 3x Elopak E-PLA-S30, year of construction: 2009, air pressure: 700kPa, weight: approx. 1000kg. Packer: Oystar A+F Traypacker TF, year of construction: 2011. Nodpfxotul Raj Af Sslg

Condition: used, Year of construction: 1993, Overview The GM Gera NAGEMA Arcade DS bottle washer was previously used in a brewery. There it was operated in single-shift operation. Since the sales volume has decreased, the beer of the brewery is now bottled at another location and this bottling line has become available. Due to the low number of operating hours and regular maintenance, the machine is in a very good condition. All basins and the machine body are made of stainless steel. Spare parts, such as bottle cells, are also still available. Furthermore, the main drive shaft, as well as the motor and gearbox were overhauled by SEW in 2018 and the carrier chain was replaced in 2015. The machine is still mounted and can also be demonstrated. Tech Specs: Capacity: 23,000 bph Cell pitch: 85 Bottles per row: 16 Dimensions + weights with attachments: 8640 x 4470 x 1920 mm / 17,900 kg Details: Standard drives Heating with steam Operating side left CE certified Chemistry dosing pumps Machine data sheet Fixed pipe spraying controlled by machine cycle Single-end machine Label discharge rear right Finger discharge + finger feeding Bottle discharge left Bottle cells plastic HMI Lauer Lye concentration measurement 24 Volt control voltage Control S5 (on request conversion to S7) Regularly maintained Water part in VA Fume extraction Sampling taps KSB pumps in VA Plug-in strainers for baths Water meter Conductivity measurement from Endress Additional Equipment: Spare parts included   Nodpfx Afjl Hx Adj Solg

Condition: good (used), Year of construction: 2000, GRUNWALD HITTPAC AKH-019R/! Item: GRUNWALD Hittpac AKH-019R/1 Grunwald-Cup Filling Machine various, margarine, sous, butter, cheese etc.. Nlsdpfx Afep R R Dws Sog Grunwald Rotary cup filling machine with 2 heads, for round cups Year of production: 2000 For hot fill of liquid products including cup lifting device servo driven and hopper with scraper agitator and feed valves (CIP cleanable), aluminum seal dispensing by vacuum and tip sealing, heat sealing of aluminum seal, snap-on cover station and out feed. Stainless steel control panel, hanging on the machine, and operator panel. Machine has polycarbonate glass safety guards. CEE machine, incl. documentation Stationed: Denmark

Condition: used, Year of construction: 2004, operating hours: 45,000 h, Used Blow Molding Machine KOSME KSB 4L up to 6800 bph The KSB 4L blow molding machine is built specifically for producing PET bottles. Notably, it offers a robust, compact solution for high-performance production. Its design is both innovative and technically straightforward. As a result, it ensures optimal efficiency and a high quality-to-price ratio. With four cavities, it effectively produces up to 6,800 bottles per hour. In addition, it accommodates formats from 0.1 to 2.5 liters. The solid, well-organized structure of the KSB 4L provides operators with flexibility and reduced maintenance needs. Furthermore, the machine has completed 22,000 hours of operation. It also includes two original molds, one for 0.5 liters and one for 1 liter. Njdpfx Aovgvb Eof Selg Heating system and preform feed in the Blow Molding Machine KOSME KSB 4L To achieve its heating capabilities, the KSB 4L’s heating system uses four heating modules and eight heating provides a heating capacity of 46 kW. Moreover, its patented positioning system places infrared lamps precisely, thereby ensuring optimal external heating of preforms without opening the oven. For efficiency, the conveyor belt system for preform feed orients and positions the preforms. It streamlines the heating process and thus reduces preparation times. Blowing process and production efficiency Furthermore, the Blow Molding Machine KOSME KSB 4L’s pneumatic preform separation system adjusts the preforms’ distance from 40 mm in the oven to 120 mm in the mold. Then, the blowing process operates in a fully replaceable station, which adapts to different bottle diameters as needed. Afterward, the transfer unit moves heated preforms into the mold cavities, where they undergo sealing, stretching, and blowing. Each cavity consequently produces up to 1,700 bottles per hour, thereby achieving high precision and stability in production. Consumption and energy requirements In terms of energy, the KSB 4L operates on a voltage of 3 x 230/400 V, with a frequency of 50 or 60 Hz, an installed power of 56 kW, and an average consumption of 36 kW. Additionally, the compressed air system maintains a working pressure of 10 bar and a blowing pressure up to 40 bar, consuming 470 Nm³/h of air. In addition, the cooling system requires a water flow of 6.6 m³/h at an inlet temperature of 5 to 7 °C, achieving a cooling capacity of 20.8 kW. Operator advantages and maintenance Notably, the design allows easy access to all internal components, thereby enabling quick format changes and simplifying mold replacement, which takes an average of only 30 minutes. Furthermore, its linear movement arrangement and durable construction materials minimize maintenance needs. Additionally, the touch-screen interface lets operators input parameters for different types of preforms and bottles, and the system offers password protection to enhance operational security. Conclusion of the Blow Molding Machine KOSME KSB 4L In conclusion, the KSB 4L serves as an ideal solution for those seeking a reliable and high-performance used machine that produces PET bottles with precise specifications and optimized consumption.

Condition: used, Year of construction: 2016, Overview This filler was manufactured in 2016 by CIMEC and comes with an Arol crown capper. The filler has an output of 1,800 bottles per hour, processes bottle sizes from 0.33 l to 0.75 l and is in very good condition. The machine can be viewed in person at any time. Technical details  Filler | CIMEC | AM DPS 9-8-1C | 2016 - Output: 1,800 bottles/hour - Number of rinsing nozzles: 9 - Number of filling valves: 8 - Bottle sizes included: 0.33 l - 0.75 l (with other set also 0.5 l) - Electrical power: 6 kW, 400V, 50Hz - Dimensions - Width: 1,400 mm - Length: 3,200 mm - Complete length with labeler: 8,800 mm Nodpfx Afjvy D Ads Solg - Operating hours: 1,370 hours - Complete documentation available Capper | Arol | TSI-Eagle C | 2016 - Pitch diameter: 410 mm - Number of heads: 1 - Type of closure: Standard crown cork - Complete documentation available