Double-shaft multirip saw A. COSTA LEOPARD 350

Costa LEOPARD

Condition: refurbished (used), MULTIBLADE A.COSTA LEOPARD 2X55KW FULL RECONDITIONED Pedpfx Ajwwipiehyogk

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW Pgodpfx Aowp Rqfshyok The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: used, Year of construction: 1986, functionality: fully functional, cutting height (max.): 180 mm, cutting width (max.): 350 mm, saw blade diameter: 350 mm, saw blade bore: 80 mm, disc diameter: 350 mm, A.COSTA LEOPARD /2/75 Cutting width: 350 mm Cutting height: 180 mm Main motors: 2 x 55 kW Feed motor: 5.5 kW Height adjustment motor: 0.37 kW Total power: 0.37 kW Pgodpfowi I Hkjx Ahysk Maximum disc diameter: 350 mm Spindle diameter: 2 x 80 mm Sleeve diameter: 2 x 100 mm Minimum element length: 800 mm Electric feed adjustment Automatic central lubrication Electric height adjustment Electric disc height adjustment Six upper pressure rollers Pneumatic clamps Anti-expel latches Weight: ± 5,500 kg 2 spare sleeves and spacers Infeed table: Infeed table connected to the main machine. Total length: 400 cm Number of rollers: 2 straight, 14 inclined. TOTAL: 16 lower rollers + 2 upper rollers Upper rollers with pneumatic pressure

Condition: used, A.COSTA LEOPARD multirip saw with double arbor - Max cutting depth: 200 mm - Width of track: 350 mm - 2 x 55 KW / 75 HP - Weight: around 5 tons Pgjdpfx Aevf Dagohyok

Condition: refurbished (used), Completely refurbished Bongioanni CRL 4 tensioning wagon with clamping blocks. Track gauge 1200 mm. Rails newly milled. Servo-electric drive. Sale upon customer order. Psdpfx Ahjxtwxbjysgk

Condition: used, engines - 55 and 55 kW Psdpfswrw D Rsx Ahyjgk feed motor - 7.5 kW height adjustment motor - 1.1 kW cutting height - 200 mm cutting width - 350 mm blade saw diameter max.- 300 mm spindle diameter - 2 x 60 mm sleeve diameter - 2 x 70 mm track width - 350 mm total power - 119 kW electric feed regulation automatic central lubrication minimum length of the element - 600 mm electric height adjustment shaft height adjustment six upper pressure rollers pneumatic clamps five anti-ejection pawls ruler stub diameter - 220 mm spindle speed - 4500 RPM dimensions of the machine (length / width / height) - 275 / 235 / 210 cm weight - ~ 7000 kg Feeders: max. cutting length - 1850 mm min. cutting length - 800 mm max. material length - 2500 mm min. material length - 600 mm max. material width - 700 mm max. material height - 200 mm roll width - 700 mm roll diameter - 130 mm number of rolls - 26 3 smooth pressure rollers 4 toothed pulling rollers feed adjustable on the inverter 0-70 m/min. central lubrication of saw guides power of the saw motor - 2 x 9.2 kW feed motor power - 1.5 kW power of the disc spreading motor - 3 kW chain motor power - 1.1 kW dimensions (length / width / height) - 7050 / 2100 / 1850 mm

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters Pgjdpfx Aou Hmacehyek 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Pgsdpfsq Nf Ensx Ahysk Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation -4 cross cut saws Pgedpfxovbtpo Ahyok -cutting cross section 180x220 mm, 150x300 mm

Condition: new, functionality: fully functional, New machine - stock clearance sale - Tipping is mechanical. The stated price is net ex warehouse location. Pgedpfx Ahow Sfdwjysk