Wood shredder

Robust Reuser SD 900/30 kW

Condition: new, Year of construction: 2026, ♻ Universal use (diverse wood, pallets with nails and pins, particle boards, waste and scraps, veneer, MDF plates, cardboard boxes, plastics, textile etc.) ♻ A shredding system integrated with a conveyor and magnetic separator offers a comprehensive solution for material processing and purification. Crsdpfx Ajtpwlrogvoc ♻ The system consists of a powerful shredder capable of breaking down various materials, a conveyor which helps to evenly distribute the shredded material, ensuring a steady flow for further processing or disposal and a magnetic separator that efficiently removes ferrous or magnetic particles from the mixture, enhancing material purity and preventing equipment damage. Technical data: Shredder: ✔ Power: 30 kW ✔ Shaft length: 870 mm ✔ Shaft diameter: 270 mm ✔ Shaft RPM: 80-120 rpm ✔ Number of cutting knives: 38 ✔ Granulation: 10-50 mm ✔ Capacity: up to 8 m3/h* ✔ Filling opening: 2031 x 1565 mm ✔ Weight: 2450 kg Z conveyor: ✔ Frequency converter (adjustment of conveyor speed) ✔ Overband magnetic separator ✔ Length: 6500 mm ✔ Width: 350 mm ✔ Capacity: 0,5 kg/s ✔ Power 0,25 kW ✔ Transport wheels 1 years warranty or 1000 working hours

Condition: new, capacity 90 degrees: round 240 mm capacity 90 degrees: square 240 mm 165 x 310 mm saw band length 2725 x 27 x 0,9 mm mm table height 890 mm band speed 35 / 70 m/min total power requirement 1,1 kW weight of the machine ca. 0,35 t Dimensions (LxWxH) 1,7 x 0,75 x 1,8 m The Z252/DG has the following equipment: - hydraulic cylinder, - emulsion pump, Cjdshpktvopfx Agvsrc - eccentric clamp, - base, - saw blade, - 400V plug -16A- The machine is delivered fully assembled and ready for immediate use.

Condition: new, Year of construction: 2026, ♻ Universal use (diverse wood, pallets with nails and pins, particle boards, waste and scraps, veneer, MDF plates, cardboard boxes, plastics, textile etc.) ♻ A shredding system integrated with a conveyor and magnetic separator offers a comprehensive solution for material processing and purification. ♻ The system consists of a powerful shredder capable of breaking down various materials, a conveyor which helps to evenly distribute the shredded material, ensuring a steady flow for further processing or disposal and a magnetic separator that efficiently removes ferrous or magnetic particles from the mixture, enhancing material purity and preventing equipment damage. Technical data: Shredder: ✔ Power: 30 kW ✔ Shaft length: 870 mm ✔ Shaft diameter: 270 mm ✔ Shaft RPM: 80-120 rpm ✔ Number of cutting knives: 2x19 ✔ Granulation: 10-50 mm Crjdpetpwh Sofx Agvjc ✔ Capacity: up to 7 m3/h* ✔ Filling opening: 1446 x 1565 mm ✔ Weight: 2050 kg Z conveyor: ✔ Frequency converter (adjustment of conveyor speed) ✔ Overband magnetic separator ✔ Length: 6500 mm ✔ Width: 350 mm ✔ Capacity: 0,5 kg/s ✔ Power 0,25 kW ✔ Transport wheels 1 years warranty or 1000 working hours

Year of construction: 1980, condition: good (used), Stellite forming machine VOLLMER GF10U Crodpfx Agogxb Ebjvoc Blade thickness 1 to 4mm Width band saw blades 60 to 420 mm circular saw blades 300 to 1.200 mm Ø electric feed drive via gear motor

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Crsdpfevf E Avjx Agvec Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 1998, condition: good (used), Make: UNION Type: Ti 1800 Year: 1998 Specifications Metric US Standard Table Length 2000 mm Table Width 1800 mm Table load 16000 Movement V-axis 1250 mm Rotation B-Axis 360.000 ° Rotation speed B-Axis 1,35 Omw/min. Movement speed V-axis 4000 mm/min. Dimensions (Estimate) Length 3400 mm Width 2000 mm Crsdpfx Agokwcdbevec Height 920 mm Weight 6500 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 2014, Technical data shown on photos. Csdjufp Svopfx Agvjrc Parts shown by hand not come.

Condition: used, Year of construction: 1981, machine/vehicle number: 78.977, Equipment: documentation/manual, Year of manufacture: 1981 / Year of retrofit: 1996/1997 Control: Siemens 840 C Siemens control for X/Y/Z/W/U/B/V axes Spindle diameter: 200 mm Main motor Siemens: 68 kW Spindle speeds: I gear: 3 - 202 rpm II gear: 180 - 808 rpm X travel: 12,000 mm Csdpfjqc Umgox Agvorc Y travel: 4,500 mm Z travel: 2,400 mm (supporting sleeve □ 520 mm/travel 1200 mm + W axis 1200 mm) Mount: SK60 (SK50) Facing slide: yes Milling head: 2 units Prepared for CNC rotary table (4th axis) Without rotary table and clamping field (available separately) Full documentation Net weight: approx. 140 tons Video available!

Condition: new, Year of construction: 2022, Layout: Shears Attachment suited for: Construction machines Credpfjpa Rpbsx Agvec Metal shear / steel shear for steel cutting for excavators It has been designed for demolishing iron structures and for cutting different structural steels It has some unique properties Replaceable cutting knives Upper head and slewing ring Specially developed hydraulic cylinder The double hose connection For detailed information and price, please contact us

Condition: new, Year of construction: 2024, ♻ Universal use (diverse wood, pallets with nails and pins, particle boards, waste and scraps, veneer, MDF plates, cardboard boxes, plastics, textile etc.) ✔ Power: 18,5 kW ✔ Shaft length: 550 mm ✔ Shaft diameter: 260 mm ✔ Shaft RPM: 80-120 rpm ✔ Number of cutting knives: 14 ✔ Granulation: 10-30 mm Cjdpfxsiq U A Sj Agvjrc ✔ Capacity: up to 4 m3/h* ✔ Material discharge opening: 160 mm ✔ Material: Plastics, cardboard, wood (chipboards, MDF boards, waste,...) ✔ Filling opening: 939 x 567 mm ✔ Dimensions L/W/H: 1,88/1,12/1,67 m ✔ Weight: 1250 kg 2 years warranty or 2000 working hours