Guidance and lathe

Bernardo Master 180

Condition: new, turning length 1000 mm turning diameter 360 mm turning dia. in gap 480 mm spindle bore 51,0 mm turning speeds 70 - 2000 U/min bed width 185 mm spindle taper 55029 D 1-5 taper in tailstock 4 MK quill travel 110 mm total power requirement 1,5 kW weight of the machine ca. 540 kg. range L-W-H 1920 x 750 x 1600 mm Equipment: - 3-axis digital display i200 with LCD display - 3-jaw chuck DK11-200 mm / D5 - Faceplate 200 mm / D5, according to DIN 55029 - Fixed steady rest - passage diameter max. 70 mm - Follow-on steady rest - passage diameter max. 50 mm - Coolant system - Initial filling with Shell Tellus 46 - Extendable chip tray - Clamping disk 320 mm - Quadruple tool holder - Protective device for quadruple tool holder - Slip clutch - Micrometer longitudinal stop - Thread gauge - LED machine light - Reducing sleeve - Change gears - 2 centering points Tjdpfoxaawaex Af Tof - Foot pedal with brake function according to CE - Motor with magnetic brake according to CE standard - Base frame - Operating tools

Condition: as good as new (ex-display), functionality: fully functional, turning diameter over cross slide: 240 mm, spindle bore: 58 mm, turning diameter over bed slide: 430 mm, center height: 215 mm, turning length: 760 mm, quill stroke: 127 mm, quill diameter: 58 mm, total length: 1,885 mm, total width: 810 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 20 rpm, bed width: 300 mm, overall weight: 1,680 kg, quill mount: MK 4, Tip height: 215 mm Tjdjcir Anepfx Af Tjf Center width: 760 mm Spindle bore: 58 mm Spindle nose according to DIN 55029 Camlock D6 Motor power: 5.5 kW Spindle speed range: 20-2000 mm Weight approx. 1680 kg Equipment including Hardened and precision-ground Z-axis guideways Turcite coatings (on mating surface) of the tool and face slides Manual central lubrication with one pump for longitudinal and cross slides Complete coolant system with rear splash guard and splash guard on the slide Chuck guard Switch rod with 3 adjustable cams Machine light Fixed center point Set of machine mounting plates

Condition: used, turning diameter over bed 250 mm turning diameter over slide rest . mm centre distance ca. 400 mm centre height ca. 125 mm turning speed range 80 - 3000 U/min number of speeds 18 spindle bore 24 mm tailstock quill taper MT 3 weight ca. 400 kg dimensions ca. 1200 x 650 x 1300 mm 4-jaw-chuck diameter 125 mm including Röhm four-jaw chuck, Ø 125 mm incl. drilling and turning jaws; collet chuck device incl. collets 1-20 mm with 1 mm gradient Tjdpfx Afjwa Dz Es Tjf Multifix size A with 3 interchangeable holders; chuck protection with shutdown

Condition: good (used), Year of construction: 2010, LZ-Lathe Fabr.JET Type :GHB-1330 Bj.2010 with 3 ash digital indicator, 3 jaws lathe chuck DM 160 mm tool holder Multifix size A, 2 steady rests coolant device. Turning diameter overbed: 330 mm Turning diameter over face: 197 mm Center width: 750 mm Spindle speeds: 70-2000 rpm spindle bore : 38 mm Tedpfx Asqwgzqjf Tjf Machine in good condition from the training workshop Machine documentation available .

Condition: new, Cardan shaft balancing machine BVI-03-74 Available in stock in Poland !!! Delivery time: one day!!! . . Machine for driveshafts weighing up to 150kg and up to 4700mm long. Suitable for small workshops with a large range of different shafts, including trucks. This balancing machine has high productivity and serves to balance the cardan shafts of cars and trucks. It makes the process of balancing the cardan shaft easy thanks to many technical solutions, while the machine has an affordable price, which reduces your financial burden and allows you to develop your business effectively. . . Tsdpopbv Tfjfx Af Tef TWO TIMES faster than your machine. This balancing machine is majored to balance the shaft not only qualitatively, but also quickly. If you can balance in 2-2.5 times faster, then this is your real competitive advantage. . . HIGH PERFORMANCE ACCESSORIES The machine is equipped with three main types of adapters: 1. Fast clamping universal adapters. It has two main advantages: The first is that due to the special design the driveshaft flange is clamped within 5 seconds. This advantage is due to the fact that the driveshaft flange does not need to be fixed with bolts. THE SHAFT CAN BE CLAMPED 4 TIMES FASTER WITHOUT BOLTS. The second advantage is the centering rings. The driveshaft is mounted in the adapters with centering rings that can be made on an ordinary lathe to fit most common driveshafts. 2. KV Flange adapters. Used for balancing shafts with cross-tooth flanges. Applies to four flange sizes: 120, 150, 180, 205 mm. Usually used on truck driveshafts. 3. Adapter with slots. Used to mount various flanges with holes. Mounting the driveshaft is the same as on universal adapters, with the help of centering rings. KEY FEATURES • Balancing of 2, 3 and 4-support cardan shafts • Shaft length up to 4700mm, weight up to 150kg • Cardan installation in 1 minute • Standard set of adapters - Installation of 80% of cardan shafts; • Three ways of fixing the center bearing • Soft-bearing type machine - high sensitivity to any vibration • Machine is operated by one worker • Sliding bearing supports - quick changeover, comfortable operation • Safety bracket with clamp for quick installation • Measurement in all planes at one time • Calibration of the machine by the operator • Displays imbalance in real time • Create and print reports SPECIFICATIONS Maximum cardan shaft weight 150 kg Maximum flange diameter 300 mm Maximum length of cardan shaft 4700 mm Number of machine supports 4 Number of simultaneously measured planes 2, 3, 4 Minimum achievable residual specific imbalance, 10 g mm/kg Rotor speed range 1000-2000 rpm Power supply 380V, 3 Ph, 50Hz Power, minimum, 2,2 kW Dimensions (length x width x height) 6000 х 1100 х 1450 mm Weight 700 kg ! We manufacture а full range of equipment for drive shaft balancing and repair service. Please contact us to get the best offer!

Condition: new, New lathe with large spindle bore. Brand : KMS Type : CS6250C TDC : 1000mm Turning diameter over bed : Ø 500 mm Turning diameter over slide : Ø 300 mm Turning diameter in bag : Ø 710 mm Turning length in bag: 240 mm Bed width : 390 mm Spindle diameter : Ø 105 mm Spindle speeds : 12 (36 - 1600 rpm) Tailstock spindle diameter : 75 mm Tailstock range : 150 mm Tailstock recording : MC 5 Machine dimensions : ± 2630 x 975 x 1270 mm (L x W x H) Machine weight: ± 2100 kg Tsdpehhm Edjfx Af Tjf Machine equipped with: - Longitudinal and transverse feed. - Rapid traverse on longitudinal and transverse feed. - Movable and adjustable stops for automatic longitudinal feed. - Thread cutting shaft (Metric/Inch/Module/DP thread cutting possible. - Multifix type quick change tool holder. - 2-axis digital readout (Brand: Sino). - 3-jaw chuck Ø 315 mm, bore 100 mm (Camlock). - 4-jaw chuck Ø 400, bore 105 mm (Camlock). - Drive plate Ø 630 mm (Camlock). - Steady rest Ø 120- Ø 260 mm. - Follow rest Ø 20 – Ø80 mm. - Coolant device.

Year of construction: 2022, condition: new, Technical data: - load capacity: 10.000 kg - Own weight: 850kg Tjdjfxw H Aspfx Af Tsf - Insertable workpiece diameter: 50 - 3500 mm - Roll diameter: 250mm - Roll width 160mm - turning speed approx. 100-2.000 mm/min - Two-pedal foot switch - Potentiometer for infinitely variable speed control

Condition: reconditioned (used), Year of construction: 1976, Universal tool milling machine Make: DECKEL Model: FP 2 Year of manufacture: 1976 - overhauled, repainted RAL7035 light grey / RAL7012 basalt grey RAL5008 grey blue Mach. No.: 6976 with guarantee geometric acceptance with test report Accessories: Todpfxsd Tytys Af Tjf - 3-A digital display FAGOR Innova 30i-M, new - Fixed table 700 x 240 mm (T-slot: 12 mm) - Vertical milling head SK 40 with Tightening thread S 20 x 2 - Coolant system - Operating instructions -used, as seen-

Condition: good (used), Motor-driven NC rotary table Stepless rotary table (pitch 0.001°) Manufacturer: Rückle Type: PKT 1000 Clamping surface: 1400 mm x 1400 mm Clamping grooves: 7 pieces Slot dimension: 22 H7 mm Slot distance: 160 mm Condition: Very good (used) Optionally with machine bed About us: MBM Maschinenservice & Gebrauchtmaschinen GmbH, is a free specialist for SHW machine tools. Our main focus lies in the field of tool milling machines. Our services include the supply of spare parts, on-site customer service, machine overhauls and control modernization. Services: - Used machines - spare parts - after-sales service - machine service - machine overhauls - control modernization Todpfxefr Ih Do Af Tjf

Condition: used, L + Z Lathe WEILER Type LZ PRIMUS GS Machine no. No. 2461 Year of construction approx. 1990 Tjdpfx Aortd Uwjf Tof Center width 400 mm Turning diameter over bed 250 mm Center height above bed 125 mm Turning diameter over support 140 mm Center height above support 70 mm Spindle bore 24 mm Spindle speed 60 - 3000 rpm 18 steps Feed lengthwise and flat Chuck flange short taper DIN 55022 size 4 Inner tailstock taper MK 2 Drive power 1.1 kW and 1.5 kW pole-changing Mains connection 380 Volt, 50 Hz - 3-axis digital readout FAGOR, type 30i-T-B - Spindle speed via 2 motor speeds and 9 gear stages - 3-jaw lathe chuck RÖHM Ø 125 mm with stepped jaws - MULTIFIX quick-change tool holder with 1 interchangeable cassette - Set of collets Ø 1 / 3 / 4 / 5 / 7 / 8 / 10 / 14 / 15 / 16 / 17 / 19 / 20 / mm - 1 centering tip for collet chuck holder - Emergency stop - Hinged chuck guard - Splash guard - Machine light - electrical diagram - Machine mounted on a steel plate (steel plate L x W x H 1200 x 500 x 30 mm, 140 kg) Space requirement L x W x H 1200 x 900 x 1560 mm Weight 520 kg good condition