Bale press

Avermann AVOS 1410 BR5-45/80

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. Bjdpsvgrh Uefx Ahvjcw The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: used, Year of construction: 2014, pressing force: 122 t, overall weight: 40,000 kg, pressure: 315 bar, Machine has been used but is surplus and therefore for sale! Bcedpfxowa N U Ds Ahvow

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours, as of March 2025 Main press force: 85 t Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying system: 5-fold vertical Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Bcedpfjv T I Evjx Ahvsw Your service team at Mertens & Frowein GmbH

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: AR5xxxx, pressing force: 28 t, total width: 2,015 mm, total length: 4,400 mm, total height: 2,500 mm, overall weight: 3,000 kg, filling opening length: 1,360 mm, filling opening width: 1,660 mm, power: 5.5 kW (7.48 HP), new hydraulic compactor container with leak protection, suitable for compacting residual waste containing moisture Bcsdpfjydlfxex Ahvjw

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Bcjdpfx Asx A U Ncjhvow Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: good (used), Year of construction: 2011, operating hours: 40,000 h, functionality: fully functional, pressing force: 88 t, filling opening width: 990 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, overall weight: 23,000 kg, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 643 m³/h, Good day, We hereby offer, subject to prior sale, a used baler including conveyor belt, wire tying stations, and bale chute from the manufacturer HSM GmbH + Co. KG, model VK 8818 FU. The following technical specifications were taken from the manufacturer's operating manual and brochures; we do not assume any liability for the correctness or completeness of this information. Manufacturer: HSM GmbH + Co. KG, Germany Model: VK 8818 FU Year of manufacture: 2011 Operating hours: approx. 40,000 hours as of July 2025 Main press force: 880 kN Specific press force: 107 N/cm² Feed opening dimensions: 990 x 1,800 mm Theoretical throughput: 643 m³/hour Bcjdsymmtcjpfx Ahvsw Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Tying: 5-fold horizontal, fully automatic Baler dimensions (set up): 12,130 x 4,800 x 3,270 mm (L x W x H) Overall installation dimensions with conveyor system: 14,000 x 23,000 x 7,745 mm (L x W x H) Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The press is in good condition and will be replaced with a new, larger press in May/June 2026. Until then, the machine can be inspected in operation with material. We would be pleased if this baler is of interest to you. Your Mertens & Frowein GmbH service team

Condition: good (used), Year of construction: 2018, operating hours: 40,350 h, functionality: fully functional, Baling Press Presona LP 85 VH2 with Cross Tying, Year of Manufacture 2018 Technical Specifications: Manufacturer: Presona Sweden Model: LP 85 VH2 Year: 2018 Drive Power: 2 x 45 kW Operating Hours: 40,350 Effective Operating Hours: Approx. 22,000 Pre-press Force: 28 t Main Press Force: 85 t Feed Opening: 1500 x 1100 mm Bale Dimensions: 750 x 1100 mm Bale Weight: 450–650 kg Theoretical Throughput Volume: 1,200 m³/h Throughput Capacity at 30–100 kg/m³: 13–30 t/h Tying: 5-fold vertical, 3-fold horizontal Bsdpfjybanisx Ahvecw Oil Tank Capacity: 2,000 L Press Transport Dimensions: 10,400 x 2,400 x 2,800 mm (LxWxH) Weight: Approx. 27,000 kg The press was removed from ongoing operation. A spare parts package is included in the scope of delivery. Technical documentation is available. Please note: All technical data refer to the manufacturer’s information. We do not assume liability for the specifications provided or for any errors. The offer is non-binding, subject to prior sale, and may be revoked at any time. Viewings are possible by appointment. Sale only by advance payment, ex works, without warranty or guarantee.