Clean air dust extractor with frequency converter

AL-KO / Alko Power Unit 350+ P FU

Condition: ready for operation (used), Year of construction: 2023, Load capacity: 1450/1125kg, load center: 600mm, lift height: 3200/4900mm, battery weight: 300-350kg, free lift: 900mm, mast height lowered: 2100mm, mast height extended: 4900mm, reach: 590mm, ground clearance under mast: 80mm, ground clearance at axle center: 50mm, track width: 1292mm, frame cross-section: 1058mm, front overhang: 655mm, wheelbase: 1120mm, rear overhang: 175mm, side shift: 80mm left / 80mm right, lost load thickness: 880mm, fork tilt back: 3°, fork tilt forward: 3°, min. turning radius: 1350mm, support arm height: 282mm, support arm length: 530mm, maximum speed: 6km/h, gradeability: 5%, battery capacity: 24V/270Ah, fork dimensions: 35x100x1070mm, front wheels (polyurethane): OD 200mm / width 50mm, rear wheel (solid rubber): outer diameter 250mm / width 75mm, AC drive motor: 24V / 2.5kW, AC pump motor: 24V / 5kW, rated power: 2.5kW, width: 1512mm, length: 1950mm, net weight without / with battery: 2800/3150kg, operating hours: 86h. An on-site inspection is possible. Itjdpfxjw S Tyas Abnek

Condition: good (used), Year of construction: 2017, NUMERICALLY CONTROLLED EDGE BANDER WITH PRE-MILLING (SPINDLES) & CORNER ROUNDING UNIT Brand: SCM Model: K 360 HP-T-ER1 Serial No.: AH/120944 Ref: 123304 Year: 2017 WORKING CAPACITIES: - Panel height to be machined: 8 - 58 mm Thickness 10 to 45 mm when using rounding unit - Panel length for edgebanding: 210 to 2500 mm - Minimum panel width to be machined: 90 to 1100 mm - Edge thickness in coil: 0.4 to 3 mm without rounding max 3 mm with rounding unit - Edge thickness in strips: max 6 mm without rounding max 3 mm with rounding unit - Edge width: panel thickness + 2 mm each side - Feed rate: 11 m/min - Minimum gap between panels: 600 mm - Panel overhang beyond the transfer chain: 30 mm MACHINE CONFIGURATION: - StarTouch control - Prepared for barcode reader - Reel holder table Ø800 mm - Front extension table - Easy size: digital positioning of infeed fence and panel passage height - Anti-adhesive spray unit - Pre-milling unit (RT-V trimmer) 12,000 RPM - Infrared panel preheating at infeed - Glue application unit (VC-VM) with interchangeable glue pot for granules, capacity: 1 kg. Heating time: 12 minutes Itedpfx Absrx S Ipjnjk Pneumatic pre-cut guillotine Digitally positioned pressure station with 3 rollers (1 roller powered and with timer) - Trimming unit (end cutting) tiltable 0-20° 12,000 RPM - Top/bottom flush trimming unit with digital positioning and copying system. 2 mm radius (or chamfer) router 12,000 RPM - Corner rounding unit R2 mm, 12,000 RPM, digital positioning - Top/bottom R1 & R2 mm radius scrapers with digital positioning - Top/bottom straight scrapers - Edge finishing spray device (Nebulizer) OTHER FEATURES: - Pre-milling group motors: 2x2 kW - End trimming motors: 2x 0.19 kW - Lift/lower motor: 0.30 kW - Feed motor: 1.1 kW - Flush trimming group motors (milling): 2x 0.65 kW - CE Marked - Lockable isolator, emergency stop buttons - Power supply: 380 V, three-phase, 50 Hz - Pneumatic supply: 8-10 bar max, dry air - Extraction: 1x Ø100 mm and 5x Ø80 mm Spindles: 780 m³/h Edge trimming: 360 m³/h Scrapers: 2x360 m³/h Max. footprint in working order: 10.80 x 2.40 m Dimensions for transport (LxWxH): 4.85 x 1.20 x 1.70 m Weight: 1568 kg Machine supplied with mounted tools, manual, spare parts list and diagrams.

Condition: new, Year of construction: 2025, New machine Year of manufacture: 2025 Standard Equipment and Accessories - Swiveling operator panel easily accessible for the operator, "eye-S 15" electronic control system. Includes: * 15" touchscreen monitor * Direct control of 6-8 axes with manual, semi-automatic, and automatic operating modes * Operator assistance with the option to manage 3 different points on the tool for accurate determination of the reference point (zero point) * Capability to store up to 1000 programs with associated images * Capability to store up to 1000 different tools with associated images * USB port * Ready for network connection - Operator aid on the electronic control, including: * Tool database management * Display of coordinates at 3 points on the tool for new reference (zero) point determination * Management of tool edge speed * Operator support for common machining tasks - "Flex" milling fence with automatic adjustment via the electronic control system. Complete fence adjusted to tool diameter, infeed jaw for required chip removal. Movable "FLEX" fence from the worktable. - Aluminium fence jaw for the milling fence with inserts for continuous support - "Fast" table insert, manually adjustable, replaces table rings for optimal workpiece support surface - Electrical pre-wiring for a power feed unit - Spindle rotation direction: right/left - Automatic motor start - Version M-E includes: * Electrospindle with max. performance from 3,400 rpm * Electrospindle power 7.5 kW (10 HP) [S6 -40%] * Interchangeable MK5 spindle * Inverter for speeds from 900 to 12,000 rpm - Interchangeable MK5 milling spindle Safety/Protection - Milling guard, max. tool diameter 160 mm - Electronic motor brake effective even without mains power - Safety sensors during tool change for: spindle stop, spindle lock, opening/closing of tool holder Itjdpfxjx Nbzuo Abnek - Electropneumatic spindle lock - Microsafety switch on machine door - Emergency stop button - Lockable main switch - Motor protection switch - Control circuit 24V - CE Declaration of Conformity - Frequency 50 Hz - Base - MACHINE LANGUAGE: German - Standard safety regulations - Manual device for feed support height adjustment according to workpiece thickness with mechanical digital display and horizontal adjustment according to tool diameter. Thanks to the operator panel column, this device allows the feed support to be swung away from the work table. - Voltage 400 V, EU - Quick tool clamping system "T-SET" Allows clamping/unclamping of tools via easy application with a compressed air gun. - L'invincibile TI 5 CE version - "LL" version worktable with two cast iron table extensions; total length 2500 mm, complete with extendable support rail for wide workpieces - Emergency stop switch - Milling spindle diameter 30 mm Availability: short-term

Condition: used, machine/vehicle number: 006488, X axis working area: 2500 mm Y axis working area: 850 mm Itjdpfxowuclxe Abnsk Main Electrospindle power: 5 KW Number of controlled axes: 3 axes Total number of drilling spindles: 11

Condition: like new (used), Year of construction: 2019, Vacomat 350 XP TWIN The Vacomat 350 XP TWIN is a high-performance dust extraction unit and a true energy-saving marvel among mobile dust extractors. Two frequency-controlled motors (5.5 kW each) ensure that the suction power is adjusted accordingly, especially under highly variable operating conditions. This ensures that only the energy that is actually needed is consumed. This dust extractor handles air volumes of up to 10,000 m³/h and is ideally suited for extracting dust from large CNC machines or entire machining centers. The innovative and highly intelligent control system automates the extraction process in conjunction with the connected machines. Extraction starts automatically as soon as a connected machining center is switched on. If the power requirement is lower, only one fan is started. As soon as several extraction points are in operation, the second fan is automatically switched on. As standard, the filter sleeves are cleaned automatically during operating breaks, as soon as all connected machining centers are switched off. Our patented filter shaking system then ensures gentle cleaning via a pneumatic/mechanical process using a compressed air connection (inlet pressure 6 bar, air consumption per cleaning cycle approx. 11 l). Optionally, and particularly recommended for very high and extremely fine dust concentrations, such as gypsum dust, an efficient pressure pulse cleaning system is available. The cleaning process via the compressed air tank takes place offline, after the extraction operation (NOTE: height then +100 mm and length +350 mm). Our Vacomats are manufactured using a modular system. As standard, the dust and chip mixture is discharged into four dust-tight chip collection containers (4 x 120 l) with durable plastic liners. A negative pressure channel securely holds the foil bags in the collection container. Viewing windows make it easy to check the fill level. Low energy consumption thanks to a modern, high-efficiency motor (IE3) "Made in Germany" and a flow-optimized internal housing with low air resistance. Heat recovery through a recirculation system: The warm exhaust air is filtered and fed back into the workshop. Low noise level: A double-walled filter sleeve housing absorbs the extraction noise directly inside the Vacomat. In addition, the fan housing is soundproof. Approved for indoor installation in the wood dust area - manufactured according to the new DIN EN 16770 standard. Healthy return air: High-quality, specially developed filter materials made of antistatic polyester needle felt filter out 99.9% of dust and chip waste from the air (dust class M for St 1 dust, according to TRGS 553). Increased safety through fire and explosion protection measures according to DIN EN 16770: pressure pulse tested up to 20,000 Pa, automatically activated powder extinguishing system - no water damage! Isdpfx Abezp Edwonetk Operational reliability: A pressure gauge continuously monitors the extraction performance. Error messages are displayed by the signal light. Low follow-up costs due to high-quality components and long service life of the filter medium: For example, an extra-large settling chamber ensures an initial separation of coarse chip waste. This prevents the filter sleeves from being additionally loaded with material. Low maintenance effort thanks to the maintenance unit on the motor console and easy access to the inside of the filter. All specifications according to the manufacturer.

Condition: new, Integrated pre-separator Integrated automatic extinguishing system Efficient and economical: large-volume compressed air tank with with fast-switching diaphragm valves for effective OPTI JET filter cleaning and minimum compressed air consumption. So simple and so effective: OPTI JET cleaning and bag filter with bag filter with snap ring lock. Extremely economical: Energy-efficient drives in accordance with IE3 Safe in the event of an emergency: Maintenance-friendly automatic extinguishing system. Peace and quiet: the soundproofed air recirculation system from AL-KO. All options are open: PLC control for manual and automatic automatic operation. Countless options from machine detection to slide control to frequency-controlled operation operation, to name just three examples. Nothing goes wrong: Collecting container with inspection window. Practical down to the last detail: container lock with ergonomically ergonomically shaped clamping lever. Can be retrofitted: conversion to discharge via briquetting press Iedpfx Aju R S A Rebnetk briquetting press or rotary feeder possible. - High suction capacity - little space requirement - 100 % air recirculation without temperature loss - (residual dust < 0.1 mg/m³) - Integrated pre-separator and expandable control unit - Optimum filter cleaning - Minimal noise level - Optional: patented fill level monitoring - Maintenance-friendly, certified automatic fire extinguishing system - Dust bulkhead for dust-free container change - (optional: safety interlocking of the containers) - Freely configurable module replacement and expansion options ----- Technical data ----- Extraction nozzle Ø: 300 mm, Nominal volume flow: 5,089 m³/h, max. volume flow: 6,000 m³/h, max. negative pressure: 2,587 Pa, Filter area: 30 m², Chip collection volume: 3 x 250 liters, Number of bags: 3 pieces, Motor 400 V: 7.5 kW, Dimensions (LxWxH): 3,000 x 1,058 x 2,361 mm, Sound pressure level: 71 dB(A), Weight: 838 kg, according to: GS - HO - 07 - new exhibition machine -

Condition: excellent (used), Edge Banding Machine HEBROCK K36 Airtronic -used- Iedpfx Absymyp Rjnetk - PC control with display - Touchscreen - Swiveling control panel - Program memory - Automatic pressure bridge adjustment - Feed via transport chain - Extendable workpiece support - Motorized adjustable infeed fence - Diamond jointing cutter, both with and against feed direction - Quick heating gluepot - Gluepot change system - Suitable for PUR adhesives - Cross-cut saw with HF motor - Flush milling unit - Flush, radius, and chamfer milling unit - Pneumatic changeover of milling unit - Multi-milling tool - Multi-radius scraper blade - Chip collection box for radius scraper blade - Air jet nozzle at the radius scraper - Flat scraper blade - Air jet nozzle at the flat scraper - Exchangeable motor for corner rounding - Spray device for separator agent - Spray device for cleaning agent - Spray device for antistatic coolant - Spray device for lubricant - LED lighting in the machine area - Exchange gluepots - Zero Joint Airtronic System ----- Technical Data ----- - Edge thickness, coil material: 0.5-3 mm - Max. edge thickness for corner rounding: 3 mm - Workpiece thickness: 8-60 mm - Workpiece thickness for corner rounding: 45 mm - Min. workpiece length: 200 mm - Feed speed: 7-10 m/min - Support plate Ø for edge material: 850 mm - Guillotine for coil material up to: 3 mm - Jointing cutter power: 2x2.2 kW - Cross-cut saw power: 0.37 kW - Milling station power: 2x0.37 kW - Corner rounding unit power: 0.37 kW - Buffing unit power: 2x0.18 kW - Extraction port Ø jointing unit: 60 mm - Compressed air connection: 7 bar - Total length: 5,540 mm - Dimensions (LxWxH): 5,540x1,210x1,450 mm - Weight: 1,700 kg Quality Information: - All settings checked - Complete basic inspection - Complete basic cleaning - Electrical system checked - Pneumatics checked - Immediately ready for operation

Condition: used, Year of construction: 1993, ANGULAR PROFILING MACHINING CENTER Brand: SAC Iodpferx Tcgox Abnotk Model: P4 Serial number: 9304 Year: 1993 Model: F5 Serial number: 93030 Year: 1993 Machines visible in our workshops CHARACTERISTICS : - Cutter rotation speed: 6000 rpm

Condition: new, Year of construction: 2025, 355 mm 10000 m³/h Ijdowugp Uspfx Abnotk Motor output 11 kW 4

Condition: as good as new (ex-display), functionality: fully functional, power: 7.35 kW (9.99 HP), input voltage: 400 V, input frequency: 50 Hz, spindle diameter: 30 mm, pivoting range: 46 °, rotational speed (max.): 18,000 rpm, rotational speed (min.): 1,000 rpm, The new profil 92 M e-motion spindle moulder is Format4’s premium model, offering maximum operating comfort and ensuring absolute efficiency through minimal setup times during milling operations. The advanced electric spindle features an HSK 63F interface for a tool quick-change system with pneumatic clamping. The swiveling range of ±46° enables limitless machining versatility. With the self-explanatory e-motion control via a 15-inch touchscreen panel, spindle speed, spindle height and angle, as well as the fence position and even the table opening, can be set intuitively and precisely. Integrated memory for tools, spindle settings, and milling programs ensures perfect repeat accuracy and the shortest setup times. Electrically controlled, eccentric inserts provide maximum table support area and significantly reduce adjustment work, especially when swiveling the spindle. The newly developed heavy-duty precision milling fence features two powered axes for precise depth adjustment of the complete fence, plus an independent, adjustable depth stop for the right-hand feeding jaw. For convenient access during curve milling, the fence can be swung completely out of the working area. Optionally, the Format4 profil 92 M e-motion can be equipped with an electrically height-adjustable power feeder. Further technical data: - Maximum tool diameter: 250 mm - Usable spindle height: 140 mm - Height adjustment: electric Optional equipment: 12 Potential-free contact 106 HSK 63F spindle, Ø 30 mm, 140 mm 118 Integral safety rulers, 650 mm 119 Table opening 255 mm with controlled eccentric inserts 183 Table extension on both sides 670 mm with 2200 mm sliding frame 213 Electrically height-adjustable feeder support, incl. horizontal tube 220 Parts list holder with A9 clipboard Advantages: - Highly efficient electric spindle with stepless speed adjustment and HSK 63F interface - Position control for milling height and angle ±46º - Position control for milling fence including offset function - Smartouch with intuitive e-motion control system - Table opening with controlled eccentric inserts (optional) - Electrically adjustable height for the feeder on overhead column (optional) Further information: - The electric spindle features a HSK F63 tool quick-change system - Clamping range: 2–25 mm with OZ25 collets - "Integral" safety rulers: 650 mm Isdpfxjwztr Ns Abnotk - Table extension on both sides 670 mm with 2200 mm sliding frame - Table opening 255 mm with controlled, eccentric inserts