Used low loader trailer / lowboy trailers for sale (316)

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Custom-tailored transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further information Chassis Steel welded construction Turntable with robust ball bearing, storage box recessed Turntable extension Foldable rear support Iasdpfx Aei Ri I Esa Ejw 2 wheel chocks with holder Aluminum side impact protection Mud flaps at the rear across the entire width Extendable wideners to 3,000 mm (not in rear slope) (However, the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the center of the loading area Wooden planks 70 mm for widening to 3000 mm Tie-down eyes, low-loader type 3 pairs of tie-down points, each rated at 10 tons, integrated in the front of the floor 6 pairs of tie-down anchor plates, top and side in the outer frame, each rated at 10 tons 1 x in the neck area the rest distributed in between with a maximum distance of 1200 mm 1 x rear slope 5 pairs of pocket slots recessed in the outer frame, inside 70 x 40 mm, (can be converted to 5-ton ring tie-down eyes, not included in the scope of supply) Towing device, turntable trailer Tow bar with tested 40 mm towing eye Note! With a 40 mm towing eye, the permissible total weight of the truck must not exceed 18000 kg; otherwise, a 50 mm towing eye is required. Axles + Suspension SAF drum brake axles Axle / chassis laser-aligned, reducing tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization in the front and rear (rocker equalization) Wheels & Tires 235 / 75 R 17.5, according to manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be pulled by towing vehicles which guarantee the effectiveness of the ABS! Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable 1 LED rotating beacon with holder, switched via parking light (beacon can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area: steel floor followed by 70 mm softwood floor, steel / diamond plate in the wheel arch area Rear slope with 70 mm softwood floor Access Ramps Steel ramps, 2800 mm long, 750 mm wide, laterally movable covered with wood with gas spring support Operating Instructions With an axle load of 10,000 kg, an exemption permit is required, only indivisible loads are possible!!! The stated total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle / support and saddle loads. Country of Registration / Signs Country of Registration: Germany 1 with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for license plate holder, two-line Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint finish Frame: RAL 3002 Carmine Red 10-year warranty against rust-through Tow bar: galv

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 7 kg, maximum load weight: 17 kg, overall weight: 24 kg, axle configuration: 3 axles, loading space length: 5,900 mm, loading space width: 2,520 mm, loading space height: 860 mm, total length: 11,070 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Chassis Steel welded construction Turntable with robust ball bearing race Foldable rear support 2 support wedges with holder Aluminum side impact protection Splash guards at the rear across the entire width Partial wheel arches on the 1st axle with anti-spray flaps, anti-spray flaps behind the 2nd and 3rd axles 1 plastic toolbox, with insert tray, w=620/h=360/d=440 mm, lockable with a padlock. Extendable widening elements to 3,000 mm (not in rear slope) Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Tie-down points for low-bed trailers 1 pair of recessed ring tie-down points at the front on the drawbar, each 5 tons 7 pairs of recessed tie-down loops on the top and sides of the outer frame, each 10 tons 1 x at the front on the drawbar 6 x in the low-bed area First tie-down point 250 mm from the front and last tie-down point max. 250 mm from the rear, distance between tie-down points not greater than 1100 mm 5 pairs of recessed beam pockets in the outer frame, interior 70 x 40 mm (can be converted to 5-ton ring tie-down points, not included in the scope of delivery) 2 pairs of folding tie-down points in addition, each 10 tons 1 x on the drawbar (projects) 1 x behind the last axle, recessed in the floor Coupling device, trailer turntable Drawbar with tested 40 mm drawbar eye Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (rocker arm compensation) Wheels & Tires 235/75R17.5 according to manufacturer's choice with M&S marking Steel rims in twin arrangement, factory silver Braking system 2-line compressed air braking system Spring brake parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connecting cable Manufacturer: Wabco or Knorr Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front Iaodpfji Riwfjx Aa Ejw 2 white/red marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connecting cable 1 LED rotating beacon with holder, switched via parking lights (light can be removed) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Floor Drawbar at the front with steel/diamond plate surface Storage box in the ramp slope recessed into the drawbar followed by 70 mm softwood floor, steel/diamond plate surface in the wheel arch area Rear slope with 70 mm softwood floor Low-bed area including rear slope 6,500 mm Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable additional ramp securing device, foldable at the bottom (to prevent lateral slippage of the ramps, not in conjunction with lateral hydraulic ramp adjustment) covered with wood with spring-loaded support Operating instructions With an axle load of 10,000 kg, a special permit is required; only indivisible loads are permitted!!! The specified total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and fifth-wheel loads. Country of registration/plates Country of registration: Germany Type approval according to EC 2007/46 24/7 service hotline

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 8,500 kg, maximum load weight: 15,500 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, loading space width: 2,520 mm, loading space height: 890 mm, total length: 11,940 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements. Further Information Low-loader trailer chassis Steel welded construction Turntable with heavy-duty ball bearing Foldable rear support 2 support wedges with holder Aluminum side impact protection Splash guards at the rear over the entire width Quarter panel fenders in front of the 1st axle Extendable widening elements to 3,000 mm (not in rear slope) (However, the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the center of the loading area Wooden planks 70 mm for widening to 3000 mm Tie-down points for low-loader 1 pair of tie-down points on the gooseneck, each 5 tons 9 pairs of tie-down eyes embedded at the top and sides in the outer frame, each 10 tons 2 x at the front on the gooseneck 7 x in the low bed 6 pairs of tie-down holes in the outer frame of the low bed, each with 5 tons. (for securing lashing straps) Coupling device for trailer turntable Drawbar with tested 50 mm drawbar eye Axles + Suspension Iodpfx Aaji Ri Izs Eeaw SAF drum brake axles Axle/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical incl. Axle load equalization at the front and rear (lever equalization) Wheels and tires 235 / 75 R 17.5 according to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air braking system Spring brake parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 1 LED warning light with holder, switched via side lights (light can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin fail-safe plugs at the front, with connecting cable Floor Gooseneck at the front with steel/diamond plate thereafter with 70 mm softwood floor, in the wheel arch area steel/diamond plate Rear slope with 70 mm softwood floor Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable covered with wood Hydraulically operated via tractor's auxiliary drive with throttle, operation on the left side Hydraulic connection with quick-release coupling NW 10/3, incl. connecting hose Operating instructions At 10,000 kg axle load, an exemption permit is required, only indivisible loads are possible!!! The stated total weight is technically possible; depending on the cargo, the total weight may not be reached while observing the permissible axle/support and saddle loads. (Poor driving and handling behavior possible due to incorrect load distribution) Country of registration / Signs Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline included prepared for license plate holder, two-line Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Painting Frame DB 7350 Novagrau 10-year warranty against rusting Drawbar galva

Condition: used, empty load weight: 4,000 kg, maximum load weight: 5,500 kg, overall weight: 9,500 kg, axle configuration: 2 axles, first registration: 03/2020, next inspection (TÜV): 01/2027, loading space length: 6,400 mm, loading space width: 2,490 mm, loading space height: 2,900 mm, total length: 25,500 mm, total width: 38,200 mm, total height: 82,500 mm, suspension: air, tire size: 205 / 65 R 17,5, color: orange, Year of construction: 2020, front tire size: 205 / 65 R 17,5, emission class: none, Equipment: ABS, ABS, axle manufacturer BPW with drum brakes, Alutec loading ramps with spring support, 3,000 mm, air suspension, twin tires, tapered rear, side panels 500 mm, tarpaulin with support structure, roll-up tarpaulin at the rear, 2 x LED reversing lights, 6 pairs of lashing rings, lift/lower function, Duomatik system, rotating beacon, can be uprated to 11,000 kg GVW. Iodpszgc Izofx Aa Eeaw

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 15,600 kg, maximum load weight: 8,400 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, loading space height: 860 mm, total length: 10,900 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Additional Information Chassis Steel welded construction 1 pair of wheel recesses embedded in the steel platform in the wheel arch area, angled for access, length at the bottom approx. 1400 mm, approx. 400 mm deep. Frame in the main beam area is 400 mm higher than the wheel recess. If machines are to be transported where the overall height needs to be checked, please provide the technical data sheet of the machine types with precise details (if the overall height is exceeded -> customer's risk, approval required). Depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer. Turntable with robust ball bearing race, storage box embedded in the turntable extension. Foldable rear support. 2 chock blocks with holder. Aluminum side impact protection. Splash guards at the rear, covering the entire width. Extendable widening elements to 3,000 mm (not in the rear slope). (However, the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm.) Storage compartment for wooden planks in the center of the loading area. Wooden planks 70 mm for widening to 3000 mm. Tie-down eyes, low loader 110 3 pairs of tie-down points, each with 10 tons capacity, integrated in the floor at the front. Includes 6 pairs of tie-down rings embedded on top and on the side in the outer frame, each with 10 tons capacity. 1 x in the neck area. The remaining ones are distributed in between, with a distance of no more than 1200 mm. 1 x rear slope. 5 pairs of pocket slots embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 tons ring tie-down eyes, not included in the scope of delivery). Coupling device, trailer turntable. Drawbar with tested 40 mm drawbar eye. Axles + Suspension SAF drum brake axles. Axle/chassis laser-aligned, reducing tire wear and fuel consumption. Parabolic suspension with maintenance-free steel-rubber bearing. Braking system 2-line compressed air braking system. Color-coded line routing for easy servicing. Spring-loaded parking brake. 2 fail-safe coupling heads at the front, with connection lines to the towing vehicle. ABS and ALB, with ABS plug at the front, with connection cable. Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Wheels & Tires 235/75R17.5, according to manufacturer's choice. Steel rims in twin configuration, factory silver. Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides. Iaedpfx Aaji Ri Rye Esw 2 white position lights at the front. 2 white/red side marker lights at the rear. 2 x 7-pole fail-safe plugs at the front, with connection cable. 1 LED rotating beacon with holder, switched via the sidelights (beacon can be removed). 2 pairs of warning panels, double LED-illuminated and extendable to 3,000 mm. Floor Front area, steel floor, included. Thereafter with 70 mm soft wood floor, in the wheel arch area steel/diamond plate covering. Rear slope with 70 mm soft wood floor. Low loader platform including rear slope 8,200 mm. Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable. Covered with wood. With spring-assisted support. Operating instructions At 10,000 kg axle load, an exception permit is required, only indivisible load is possible!!! The specified total weight is technically possible, depending on the load, the total weight may not be reached while observing the permissible axle/support and saddle loads. Country of registration/sign

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 8,400 kg, maximum load weight: 15,600 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, loading space height: 860 mm, total length: 10,900 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-tailored transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Further information Chassis Steel welded construction Turntable with robust ball bearing race Foldable rear support 2 wheel chocks + holder Aluminum side impact protection Splash guards at the rear over the entire width Quarter panel fenders in front of the 1st axle 1 pair of wheel recesses embedded in the low-bed area in front of the 1st axle, angled for entry, approximately 1600 mm long at the bottom, approximately 400 mm deep. Note: Frame in the main beam area is 400 mm higher than the wheel recess. 2 pairs of wheel recesses embedded in the low-bed area between the axles, angled for entry, approximately 600 mm long at the bottom, approximately 300 mm deep. Note: Frame in the main beam area is 300 mm higher than the wheel recess. Extensible widening to 3,000 mm (not in the rear slope) Wooden planks 70 mm for widening to 3000 mm Tie-down eyes, low-bed trailer Iedpfxoi Ri Rvs Aa Eeaw 1 pair of tie-down cutouts embedded in the longitudinal beam at the front in front of the 1st axle, each 10 tons. 4 pairs of tie-down holes in the outer frame, each 5 tons. 7 pairs of tie-down eyes embedded on the top and side in the outer frame, each 10 tons. 1 x at the front in front of the 1st axle 6 x in the low-bed First tie-down eye 250 mm from the front and last max. 250 mm from the rear, distance between tie-down eyes not greater than 1100 mm Coupling device, trailer turntable Tow hitch with tested 40 mm tow ball Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned, reducing tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing Wheels and tires 235/75R17.5, according to manufacturer's choice Steel rims in twin configuration, factory silver Braking system 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connecting cable. Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides, 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole non-interchangeable plugs at the front, with connecting cable 1 LED rotating beacon with holder, switched via parking lights (beacon can be removed) 2 pairs of warning signs, double LED-illuminated and extensible to 3,000 mm Floor Front slope with steel/diamond plate covering Storage box embedded in the drive-over slope to the front slope, then with 70 mm soft wood floor, in the wheel arch area steel/diamond plate covering Rear slope with 70 mm soft wood floor Low-bed platform including rear slope 6500 mm Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Covered with wood With spring-assisted support Operating instructions With an axle load of 10,000 kg, an exemption permit is required, only indivisible loads are possible!!! The specified total weight is technically possible, depending on the load, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and handling behavior may occur due to incorrect load distribution) Registration country/Signs Registration country: Germany With DEKRA acceptance and certi

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,000 kg, maximum load weight: 13,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space width: 2,520 mm, loading space height: 380 mm, total length: 12,000 mm, total width: 2,550 mm, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Further Information Chassis Steel welded construction Turntable with robust ball bearing race, storage box recessed in the turntable extension Foldable rear support Chocks with holder Aluminum side impact protection Splash guard at the rear over the entire width Quarter panel fenders in front of the 1st axle Spare wheel holder for 1 spare wheel, with wheel fastening kit Spare wheel, same brand as the standard tires, steel rim Plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock. (Lock not included) Tie-down points for low-loader 3 pairs of tie-down points, 10 tons each, integrated in the floor at the front 6 pairs of tie-down eyes recessed in the upper and side parts of the outer frame, 10 tons each 1 x at the neck area, the rest spaced out with a maximum distance of 1200 mm 1 x rear slope 5 pairs of ring tie-down points recessed in the outer frame, 5 tons each (can be converted to stake pockets) Coupling device, trailer, turntable Drawbar with tested 40 mm drawbar eye Axles and Suspension SAF drum brake axles Axle/chassis laser-aligned, reducing tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber mounting Wheels and Tires 235 / 75 R 17,5 According to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring brake parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connecting cable Voltage converter for 12/24 Volt operation Note! A 7-pin socket, 12 Volt, is required on the tractor/tow vehicle! (Required in conjunction with the voltage converter for electrical system!) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white/red position lights at the rear 2 white position lights at the front Additional LED work lights at the rear, switched on via reversing light 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 x 7-pin agricultural plug Voltage converter 12/24 Volt (only for electrical system, not for ABS/EBS) Floor Front area: steel floor Then with 70 mm softwood floor, steel/non-slip sheet metal covering in the wheel arch area Rear slope with 70 mm softwood floor Low-loader platform including rear slope 8,200 mm Loading Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable Covered with wood With spring-assisted support Operating Instructions A special permit is required for an axle load of 10,000 kg. The permit must be applied for separately in each federal state; a guarantee for a 20-ton gross vehicle weight must not be given by the legislator. Customer risk. Country of Registration / Signs Country of registration: Germany With DEKRA inspection and certificate (according to §13 EG - FGV) 24/7 Service Hotline Prepared for license plate holder, two-line Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau Isdpji Ri Nxsfx Aa Ejaw 10-year warranty against rust Drawbar galvanized or black, according to manufacturer's choice Loading ramps hot-dip galvanized Note: Archive images!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 14,300 kg, maximum load weight: 9,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, loading space height: 900 mm, total length: 12,000 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further Information Chassis Steel welded construction Turntable with robust ball bearing Foldable rear support 2 wheel chocks + holder Aluminum side underrun protection Splash guards at the rear over the entire width Quarter panel fenders in front of the 1st axle Iaedpfei Ri I Nex Aa Esw Excavator arm recess starting above the rear axles to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess on the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box recessed in the gooseneck in the floor with a lid, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the gooseneck in the low-loader wheel well area, sloped for access, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses between the axles recessed in the low-loader in the wheel well area, sloped for access, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in the main beam area is 300 mm higher than the wheel recess. Wheel recess cover pull-out from the main frame, with wood inserts. Distance from the outer frame, beam to beam, approx. 1280 mm Extensions pull-out to 3,000 mm, foldable at the wheel recess extensions (extension not in the rear slope and not in the wheel recesses at the bottom) Storage compartment for wooden planks in the middle of the loading area or under the loading area, depending on technical feasibility Wooden planks 70 mm for extension to 3000 mm Lashing points, low-loader 1 pair of ring lashing points recessed at the front on the gooseneck, each 5 tons 8 pairs of lashing eyes at the top and on the side recessed in the outer frame, each 10 tons 2 x at the front on the gooseneck 6 x in the low-loader, the first lashing point 250 mm from the front and the last one max. 250 mm from the rear, the distance between the lashing points is no more than 1100 mm 5 pairs of ring lashing points recessed in the outer frame, each 5 tons (can be converted to stake pockets) Coupling system, trailer, turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned, reducing tire wear and fuel consumption Air suspension with lifting and lowering valve, can be operated separately at the front and rear Wheels and tires 235/75R17.5 according to manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake Trailer Info Center for displaying vehicle data such as axle load (no calibrated scale) and odometer Axle load detection via EBS-CAN bus signal, for display on the display in the cab, truck must be suitably prepared, no truck installation (no calibrated scale) Vehicle-driving stability system Duomatic connection at the front, with connecting cable to the towing vehicle EBS, Electronic Braking System with EBS plug at the front, with connecting cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights in LED with resistor, yellow LED lighting on the side, license plat

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, overall weight: 24,000 kg, axle configuration: > 3 axles, loading space height: 900 mm, total length: 11,940 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Additional Information Low-bed semi-trailer chassis Steel welded construction Turntable with heavy-duty ball bearing ring Folding rear outriggers 2 support wedges with holder Aluminum side impact protection Rear splash guards covering the entire width Semi-fender for 1st and 2nd axles with anti-spray splash guards behind each axle, anti-spray splash guards in front of and behind the 3rd and 4th axles Excavator arm recess above the rear axles, extending to the rear, approximately 1800 mm long, approximately 650 mm wide and approximately 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess, laterally on the longitudinal frame, approximately 300 mm from the front and approximately 200 mm in front of the rear slope 1 plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock (lock not included) 1 storage box recessed in the gooseneck at the bottom with lid, W=720 mm/ L=520 mm / D= 170 mm Extendable widening elements to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading platform Lashing eyes for low-bed trailer (40 lashing options) 1 pair of lashing eyes on the gooseneck, each 5 tons 9 pairs of lashing eyes embedded above and on the side in the outer frame, each 10 tons 2 x at the front on the gooseneck 7 x in the low bed 6 pairs of lashing eyes in the outer frame from the low bed, each 5 tons (for attaching tie-down straps) 3 pairs of folding lashing eyes additionally, each 10 tons 1 x inside next to the main frame at the beginning of the low bed 1 x on the gooseneck (protruding) Iedpfx Aaji Ri Daj Eeaw 1 x behind the last axle, recessed in the floor Coupling device for the trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined by 8° / D-value min. 160 kN Axles + Suspension Drum brake axles Parabolic spring suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization at the front and rear (rocker equalization) Wheels and Tires 235 / 75 R 17.5 according to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connecting cable Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of warning signs double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel / checkered plate covering followed by 70 mm softwood floor, wheel arch area with steel / checkered plate covering Rear slope with 70 mm softwood floor Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable covered with wood Hydraulically operated via towing vehicle auxiliary drive with throttle, operation on the left-hand side at the front Hydraulic connection with SVK plug NW 10/3, incl. connecting hose Country of Registration / Signs Country of Registration: Germany 24/7 Service Hotline prepared for two-line license plate holder Contour marking with reflective strips ac

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 8,500 kg, maximum load weight: 15,500 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, loading space width: 2,520 mm, loading space height: 890 mm, total length: 11,940 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-Tailored Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. More Information Chassis Steel welded construction Turntable with heavy-duty ball bearing Foldable rear support 2 outrigger plates with holder Aluminum side impact protection Splash guards at the rear, covering the entire width Semi-elliptical fenders for 1st and 2nd axles with anti-spray splash guards behind each axle, anti-spray splash guards in front of and behind the 3rd and 4th axles Excavator arm recess starting above the rear axles and extending to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points, each 5 tons, in the excavator arm recess on the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm in front of the rear slope. 1 plastic toolbox with insert, w=620/h=360/d=440 mm, lockable with a padlock (lock not included). 1 storage box recessed into the gooseneck with a cover, W=720 mm / L=520 mm / D=170 mm Extendable widening sections to 3,000 mm Wooden planks, 70 mm, for widening to 3,000 mm Storage compartment for wooden planks under the loading area Lashing points for low-bed trailers (40 lashing options) 1 pair of lashing points on the gooseneck, each 5 tons 9 pairs of lashing eyes recessed on the top and side of the outer frame, each 10 tons 2 x at the front on the gooseneck 7 x in the low bed 6 pairs of lashing points in the outer frame of the low bed, each 5 tons (tie-down strap attachment) 3 pairs of folding lashing points, each 10 tons 1 x inside next to the main frame at the beginning of the low bed 1 x on the gooseneck (overhanging) 1 x behind the last axle, recessed into the floor Coupling device, trailer turntable Tow hitch with tested 50 mm drawbar eye, drawbar eye inclined 8°, D-value min. 160 kN Axles + Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization at the front and rear (rocker arm equalization) Wheels and Tires 235 / 75 R 17.5, according to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring brake parking brake 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS connector at the front, with connecting cable Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe connectors at the front, with connecting cable 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel/diamond plate covering followed by 70 mm soft wood flooring, steel/diamond plate covering in the wheel arch area Rear slope with 70 mm soft wood flooring Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable covered with wood with spring-assisted support Country of Registration/Signs Country of Registration: Germany 24/7 service hotline prepared for license plate holder, two lines Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Iasdpfxsi Ri A So Aa Esw Warning sign according to ECE - 70 Paintwork Frame hot-dip galvanized including passivation, 15-year

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, total length: 11,990 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements. More information Chassis Steel welded construction Turntable with heavy-duty ball bearing, storage box recessed in the turntable extension Foldable rear support 2 support wedges with holder Aluminum side impact protection Splash guards at the rear over the entire width Extendable widening sections to 3,000 mm (not in the rear slope) Storage compartment for wooden planks in the center of the loading area Wooden planks 70 mm for widening to 3000 mm Tie-down eyes for low-bed trailers 3 pairs of tie-down points, each with 10 tons capacity, integrated in the floor at the front 6 pairs of tie-down recesses on the top and sides of the outer frame, each with 10 tons capacity 1 x near the gooseneck area the rest distributed in between, with a distance of no more than 1200 mm 1 x rear slope 5 pairs of lashing pockets recessed in the outer frame, 70 x 40 mm inside, (convertible to 5-ton ring tie-down eyes, not included in the scope of supply) Coupling device for trailer turntable Drawbar with tested 40 mm drawbar eye Axles + Suspension SAF drum brake axles Axle / chassis laser-aligned, reducing tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical Axle load equalization (rocker equalization) Braking system 2-line compressed air braking system Color-coded line routing for easy servicing Spring-loaded parking brake including 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS plug at the front, with connection cable, Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17.5 at the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pin fail-safe plugs at the front, with connection cable, 1 LED rotating beacon with holder, switched via parking lights (beacon can be removed) 2 pairs of warning signs, double LED-illuminated and extendable to 3,000 mm Floor Front area with steel floor, then with 70 mm softwood floor, in the wheel arch area steel / tread plate covering Rear slope with 70 mm softwood floor Iaedsi Riy Ejpfx Aa Esw Low-bed platform including rear slope 8,200 mm Ramps Steel ramps 2800 mm long, 750 mm wide, laterally movable covered with wood including with spring-loaded support Operating instructions An exemption permit is required for a 10,000 kg axle load; only indivisible loads are possible!!! The specified total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle / support and saddle loads. Country of registration / signs Country of registration: Germany with Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline prepared for two-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Paint finish Frame DB 7350 Novagrau 10-year warranty against rust-through Drawbar galvanized or black, at the manufacturer's choice Ramps hot-dip galvanized Note: Archive images! Customized transport solution Configure your Flieg

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 7,900 kg, maximum load weight: 16,100 kg, overall weight: 24,000 kg, axle configuration: 2 axles, loading space width: 2,520 mm, loading space height: 900 mm, total length: 11,625 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-tailored transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Further information Chassis Steel welded construction Turntable with heavy-duty ball bearing Foldable rear support 2 jacking plates with holder Splash guards at the rear over the entire width Preparation for widening to 3,000 mm (holes in the outer frame and not in the rear slope) Tie-down eyes, low loader 1 pair of tie-down recesses embedded in the front longitudinal member on the extension, 10 tons each 7 pairs of tie-down studs embedded in the top and sides of the outer frame, 10 tons each 1 x at the front on the extension 5 x in the low bed 1 x in the rear slope 12 pairs of tie-down holes in the outer frame, 5 tons each (for securing tie-down straps) 5 x on the extension, 6 x in the low bed and 1 x in the rear slope Coupling device, trailer turntable Tow hitch with tested 40 mm drawbar eye Axles + Suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization (lever equalization) Wheels and tires 235 / 75 R 17.5 Fulda Steel rims in twin arrangement, factory silver Braking system 2-circuit compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle Connecting lines extended by approx. 60 cm Without ABS, but with mechanical ALB, then max. 60 km/h approval Electrical system 12 Volt, multi-chamber lights, without yellow LED lighting on the sides, side reflectors 2 white position lights at the front 2 white/red side marker lights at the rear 1 x 7-pin 12 Volt plug at the front, with connecting cable, extended by approx. 60 cm 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of illuminated and extendable warning signs to 3,000 mm Floor Front extension with steel/non-slip sheet covering Storage box embedded in the ramp to the extension Followed by 70 mm soft wood floor, steel/non-slip sheet covering in the wheel arch area Rear slope with 70 mm soft wood floor Low loader bed incl. rear slope 5900 mm Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable Covered with wood With spring-loaded support Operating instructions With 10,000 kg axle load, an exemption permit is required, only indivisible loads are possible!!! The specified total weight is technically possible, depending on the cargo, the total weight may not be achieved while complying with the permissible axle/support and drawbar loads. (Poor driving and handling behavior possible due to incorrect load distribution) Registration country / signs Registration country: Germany With Dekra approval and report, for max. 60 km/h approval, towing vehicle LoF (registration country Switzerland max. 40 km/h possible) Prepared for license plate holder, two lines Iaedei Ri Agspfx Aa Esw Without contour marking / reflective strips according to ECE R 048 Painting Frame DB 7350 Novagrau 10 years warranty against rust perforation Tow hitch galvanized or black, at the manufacturer's choice Ramps hot-dip galvanized Note: Archive images!

Condition: used, maximum load weight: 23,700 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 01/2008, total width: 2,550 mm, total height: 3,700 mm, Equipment: ABS, German trailer, * 30-ton capacity * Extendable to 3 meters * Spring-loaded ramps * 50mm drawbar eye * Air suspension Ijdpfx Ajy Trntsa Eoaw New TÜV (technical inspection) available for an additional charge!!! For further information, please call Christian Bredemeier.

Condition: used, maximum load weight: 509 kg, overall weight: 750 kg, axle configuration: 1 axle, first registration: 02/2026, loading space length: 2,950 mm, loading space width: 1,600 mm, loading space height: 120 mm, total width: 2,240 mm, total height: 830 mm, Multitransporter 3016, manufacturer TEMARED, model DMC, gross weight: 750 kg, 295x160 cm, with overrun brake, 100 km/h (accessory), with foldable loading ramp (accessory), low loader, height-adjustable. Subject to errors and prior sale. Iaedpfx Asym Ih Isa Eew

Condition: used, maximum load weight: 1,950 kg, overall weight: 2,700 kg, axle configuration: 2 axles, first registration: 02/2026, loading space length: 4,000 mm, loading space width: 2,010 mm, loading space height: 115 mm, total width: 2,540 mm, total height: 500 mm, A25 GW26NG000031 Car transport trailer, manufacturer STEMA, type FTAK 27-40-21.2, Gross weight: 2,700 kg, with overrun brake, WAP901 hand winch, low loader, hydraulically tiltable. Main frame: Extremely sturdy and torsion-resistant with crash-tested safety V-drawbar. Tiltable, robust frame construction with safety locks. All frame parts are hot-dip galvanized for corrosion resistance. Iedpfjyn Ucbjx Aa Eeaw Running rails: Extra wide, perforated, non-slip running rails made of galvanized sheet with large elongated holes for secure fixing of tie-down straps. The extra-wide track allows easy transport of vehicles with different wheelbases. Integrated drive-on ramps facilitate easy loading and unloading. Side panels: Signal red powder-coated (corrosion-free and scratch-resistant) for enhanced safety. Vehicle not reconditioned ...and much more. Errors and prior sale reserved.

Condition: new, empty load weight: 4,590 kg, maximum load weight: 15,410 kg, overall weight: 20,000 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,540 mm, loading space height: 400 mm, suspension: air, tire size: 235/75R17,5, Equipment: ABS, | Humbaur HBTZ217224 BS tandem low loader 20t version | height-adjustable drawbar with crank 800-1070 mm | solid welded chassis frame, hot-dip galvanized, | 2 hydraulic solid steel ramps can be moved sideways | dimensions loading area: L: 7.20m W: 2.54m Height BW: 0.40m | vehicle rear sloping with rear support | 6 pairs of heavy-duty lashing eyes recessed in the floor | lashing rings in the outer frame, | SAF axle with drum brake | total weight: 20.000 kg, payload:15.360kg | tires: 235/75R17,5 twin tires | operating voltage 24V | floor covering made of 50mm softwood floor | towing eye 50mm diameter | lashing rings in the outer frame, | errors excepted, subject to change and prior sale. Iajdpfewkqw Uox Aa Esw

Condition: used, maximum load weight: 30,860 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 01/2026, next inspection (TÜV): 01/2027, Equipment: ABS, Excerpt from the equipment list. Complete equipment list available upon request. Frame * Steel welded construction with front frame extension * Front corners beveled, rear bevel * Access ramp with excavator bucket recess in the center = recess at the rear between the longitudinal beams, approx. 2,300 mm long Integrated into the outer frame * 4 pairs of approx. 4 t lashing bars * 7 pairs of recessed, retractable approx. 10 t lashing rings (2x on the raised platform * 1x in the front extension slope * 3x in the low-bed between the wheel recesses and 1x in the access ramp * 2 pairs of wheel recesses * 1 pair of wheel recesses, approx. 2,300/1,270 x 400 mm (L1/L2 x W) * Front, after the extension, incl. one-piece drivable aluminum cover, for max. surface load of approx. 11,650 daN/piece * 1 pair of wheel recesses, approx. 1,390/590 x 270 mm (L1/L2 x W), between the 3rd and 4th axles, incl. one-piece drivable aluminum cover * Suitable for the transport of wheel loaders with a wheelbase of approx. 2,700 - 3,600 mm, with wheel diameter of approx. 1,485 - 1,740 mm * Wheel loader overhang at the rear max. 2,220 mm, width between the wheel recesses approx. 1,255 mm (= outer/outer longitudinal beam) * Reinforced ball-bearing swivel ring for a total weight of 44 t Frame attachments * 5 pairs of receiving pockets in the outer frame for square tube supports, approx. 100 x 50 x 5 mm (3x in the low-bed and 2x on the raised platform) * 4 pairs of foldable approx. 10 t lashing rings * Arrangement: 1 pair at the front on the raised platform, inside the longitudinal beams * 1 pair at the very rear in the excavator bucket recess on the left and right * 1 pair at the front on the raised platform in front of the extension, inside the longitudinal beams * 1 pair in the low-bed at the rear in front of the access ramp * Towing device in the excavator bucket recess on the left and right: Fixed drawbar with approx. 50 mm heavy-duty towing eye * Extended design, silent block bearing * Drawbar retaining spring with tensioner, truck coupling height from approx. 775 mm to approx. 975 mm, drawbar length approx. 1,800 mm Support system * 2 hydraulic supports at the rear - individually operated * Control unit housed in a separate stainless steel box Axles * SAF air suspension low loader axles with drum brakes * Load capacity approx. 11 t/axle, S-cam brake approx. 300/200 mm * Automatic brake linkage adjuster Isdpfxszdmike Aa Ejaw Wheels * 16 tires 245/70 R 17.5, 146/146F * Manufacturer Conti HTR2, 16 steel rims 6.75 x 17.5, with offset, painted black * Black plastic wheel nut covers Braking system/suspension * Two-line compressed air braking system according to ECE Directive R13 * Manufacturer Wabco EBS system 4S3M, 1st + 3rd axle sensed, RSS/RSP * Stability program, spring brake parking brake on 3rd + 4th axle * Aluminum air tanks, brake/air connection lines with 2 single coupling heads, yellow/red, EBS/ABS connection cable, rubber strap as holder for EBS and electrical plug, air suspension with lifting and lowering device, operable separately at the front and rear * Automatic adjustment to programmed driving level from 15 km/h Floor * Softwood floor approx. 50 mm, impregnated, approx. 5 - 10 mm * Protruding above the top edge of the frame, steel tear plate cover over the rear wheels Ramps * 2 pieces foldable 2-part steel access ramps * Hydraulically foldable, slope approx. 10 degrees * Length approx. 2,750 + 1,350 mm, width approx. 800 mm, with hardwood floor approx. 50 mm, impregn

Condition: used, maximum load weight: 7,580 kg, overall weight: 9,990 kg, axle configuration: 2 axles, first registration: 08/2019, next inspection (TÜV): 05/2027, loading space length: 5,000 mm, loading space width: 2,010 mm, loading space height: 250 mm, We are very pleased that our offer has sparked your interest, and we assure you that you will be able to purchase a good and affordable vehicle with a traceable service history from us! Front support jacks Rear drop-down supports Tie-down points along the sides + large tie-down points in the corners Ramps with hydraulic dampers Height-adjustable towing device Galvanized body PAYLOAD: 7,580 KG GERMAN VEHICLE REGISTRATION / CUSTOMS SERVICE We will organize your registration and the export documents / EUR 1 and manufacturer's declaration for export. FINANCING Upon request, we will gladly provide you with a LEASE-PURCHASE or FINANCING offer. SERVICE Vehicle inspection (TÜV/HU) / Occupational Safety and Health inspection (UVV LBW) / Load securing inspection (LGS) / Tachograph inspection / Installation of On-Board Unit (OBU) and service by our AUTHORIZED WORKSHOP. TOLL / ROAD TOLLS Toll can be booked on site. ARRIVAL / DISTANCES Wittlich train station 500 m away Frankfurt Airport 150 km away Iajdpfxjzc Dgfe Aa Eew Frankfurt-Hahn Airport 40 km away Luxembourg Airport 75 km away Sale in accordance with our General Terms and Conditions. The information on the internet is a non-binding description and does not constitute guaranteed characteristics. The seller is not liable for typographical and data transmission errors. VEHICLE LOCATION: Dr. Oetker Str. 22 / 54516 WITTLICH-Wengerohr.

Condition: used, axle configuration: 3 axles, first registration: 06/2010, total length: 9,500 mm, total width: 2,550 mm, total height: 940 mm, suspension: steel, color: other, Year of construction: 2010, Equipment: ABS, = Additional options and accessories = - BPW-Assen - Drum brakes = Remarks = Damm SL28M, 2010, BPW axles, Leaf-pinnate, Drum brakes, Charging ramp = More information = Suspension: leaf suspension Rear axle 1: Double wheels Rear axle 2: Double wheels Rear axle 3: Double wheels Empty weight: 8.280 kg Carrying capacity: 21.720 kg GVW: 30.000 kg = Dealer information = Iodpfx Aaszcurfe Eeaw Bank data: Rabobank Account: 39.33.10.655 IBAN: NL73RABO0393310655 Swift code: RABONL2U - Always check our bank details before transaction! - Reservation of vehicles is not possible without a deposit. - Writing and text errors are reserved for all vehicles offered.

Condition: used, empty load weight: 5,100 kg, maximum load weight: 12,900 kg, first registration: 03/2014, next inspection (TÜV): 04/2025, total length: -1 mm, total width: 25,500 mm, suspension: steel-air, tire size: 245 / 70 R 17.5 / 8mm, front tire size: 245 / 70 R 17.5 / 8mm, operation weight: 18,000 kg,

Condition: used, axle configuration: > 3 axles, first registration: 01/2019, suspension: steel, Year of construction: 2019, 40-ton low-loader with ramps – extensions – hooks for securing machinery – total weight 40,000 kg – unladen weight 8,200 kg – Iajdpfx Aozcqb Asa Ejw 1st to 2nd axle = 1,410 mm 2nd to 3rd axle = 4,530 mm 3rd to 4th axle = 1,410 mm = Further Information = Suspension: Leaf spring suspension Front axle 1: Steered Front axle 2: Steered Unladen weight: 8,200 kg Payload: 31,800 kg Gross vehicle weight: 40,000 kg Reference number: 48 Please contact Miguel Cubas for further information. = Company Information = We are located between Antwerp and Brussels along the A12 motorway, near the port of Antwerp. Opening hours: Monday to Friday continuously from 8:30 am to 7:00 pm.

Condition: used, first registration: 05/2003, loading space length: 6,379 mm, loading space width: 2,454 mm, loading space height: 39 mm, * BPW axles * 50mm towing eye * Loading ramp * Tire size: 235 / 75 R 17.5 * Technical gross weight: 18,000 kg * Curb weight: 4,450 kg * Total length: 8,420 mm Vehicle number: 11602 -- Subject to errors and prior sale -- Advertising and various lettering have been digitally removed. Iodpfx Asyl Rhbja Esaw ---We are happy to assist you with all formalities involved in purchasing a vehicle. Simply let us know your requests and suggestions, and we will take care of them. Among other things, we can offer you the following services for an additional fee: ---Trade-in of your old vehicle, TÜV/SP inspection, complete export handling, financing arrangements, application for export license plates, vehicle transfers, vehicle registration, vehicle recovery and transport. ---Your VTS Team

Condition: used, overall weight: 24,000 kg, axle configuration: > 3 axles, first registration: 12/2010, next inspection (TÜV): 11/2025, * SAF axles * Wheel wells Iodpfovav U Sox Aa Ejaw * 4th axles * Hydraulic loading ramps * 50mm towing eye * Unladen weight: 9,650 kg * Permissible total weight: 24,000 kg * TÜV: 11/2025 * SP: 05/2025 -----Internal vehicle number: 10093----Errors and prior sale excepted. WhatsApp support available! If you have any questions about the vehicle or need further information, feel free to message us conveniently via WhatsApp Whatsapp Whatsapp

Condition: used, overall weight: 24,000 kg, axle configuration: > 3 axles, first registration: 04/2016, next inspection (TÜV): 11/2025, * SAF axles * Wheel recesses * 4th axle * Hydraulic loading ramps * 50mm towing eye * Unladen weight: 9,460 kg * Permissible total weight: 24,000 kg * TÜV: 11.2025 * SP: 05.2025 -----Internal vehicle number: 10091----Subject to errors & prior sale. Iaodpfx Aasvawace Eow WhatsApp support available! If you have questions about the vehicle or need more information, feel free to contact us conveniently via WhatsApp.

Condition: used, maximum load weight: 31,050 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 06/2016, next inspection (TÜV): 06/2026, loading space length: 9,500 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,550 mm, total height: 3,650 mm, Equipment: ABS, * Schwarzmüller 4-Axle Low Loader with 2-piece hydraulic folding ramps - high-coupling with 50 mm towing eye - * Air suspension - BPW axles - disc brakes - Tyres: 245/70R17.5 * Overall length: 11,900 mm - Width: 2,500 mm (3,000 mm possible) - Height: 3,650 mm * Gross vehicle weight: 40,000 kg - Unladen weight: 8,950 kg - Payload: 31,050 kg * German vehicle - German registration documents - immediately available - from first owner * The left rear hydraulic support needs to be repaired * Viewing by appointment only * Contact: Mr. Andreas Vogel * The information provided online is non-binding and for description purposes only. * These do not constitute guaranteed characteristics. Iedpfjy Dy Enox Aa Eoaw * The seller accepts no liability for typographical or data transmission errors. * Subject to alterations, errors and prior sale.