Planing and resaw line

Waco and Canali 3000 and ML1100

Condition: excellent (used), Storti RM 500 edger - Italian production - year of production 1993 - electric spacing of discs TECHNICAL PARAMETERS: - cutting width max 435 mm - cutting height max 170 mm - engine power 2 x 22kW - max element width 600 mm - minimum material length 800 mm - max disc diameter 600 mm Laodpek Talpsfx Ancja - spindle diameter 40 mm - two upper pulling rollers - one upper pressure roller - roller motor power 2 x 1.1 kW - roller pressure with automatic jump - seven bottom pulling toothed rollers - electric disc adjustment - two lasers - feed speed 25 and 50 m/min - feeding table 2950 mm - receiving table 3000 mm - drive rollers D100 mm - power of the roller feed motor 2 x 1.5 kW Transport dimensions 500x240x180 cm weight 3500 kg

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC Lajdowp Rqfjpfx Ancsa The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Year of construction: 2000, condition: excellent (used), Span approx. 20,0 m Lifting height approx. 8,0 m Make/reconstruction HILGERS/TEICHMANN Modification/New construction 2000/2021 Crane equipped with: - Double-rail trolley with 4-corner rope outlet - Magnet System prepared - Radio remote control Lsdpfx Ansqfc Egscsaa - Optionally with magnetic traverse or spreader

Condition: new, Year of construction: 2024, Boring and inserting machines Rilesa Vlg 2200 new 2023 Make: Riles Model: Vlg 2200 Description: Condition: new Year: 2023 Start type: to be agreed Cost of delivery: Customer cover Conditions of delivery: OWN RECEIPT Category: Machine Tools equipment in Poland Subcategory: Drills Lajdsgbpmhjpfx Ancea Subcategory 2: Drilling machines Description DRILL DRILL WITH STORAGE 8 DRILLING UNITS TWO FRONT RIGHT AND LEFT, 3 UPPER AND 3 BACKS Year: 2023 new

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation Lodjvbtpjpfx Ancsaa -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm

Condition: excellent (used), Weinig four-sided planer max planing width 230mm max planing height 120mm 5 heads, bottom-5,5KW; left and right-11KW, top-11KW, bottom-5,5KW feed - 4KW fully adjustable heads electrically adjustable up and down and planing width Lodpfsrigxysx Ancjaa 40mm spindles feed on gimbal rollers, with smooth adjustment WEINIG brand solid planer, length of the machine 415cm machine checked in original condition

Condition: ready for operation (used), Slab recovery line with below machines: One 2-blade board edger One single blade horisontal resaw Conveyors system between the machines included. Lsdpfx Ajgwqk Soncjaa

Condition: refurbished (used), Dry board sorting line - dry board sorting line - 20 pockets - belt - automatic spacer collection - Trimmer Almab with 16 saw blades - automation- TG automation, Sweden Sorting - Dynalyse MC Pro 2400 System - marking/printer - Alpha Dot Merlyn 350 - Drum chipper Erjo 204 MA Lasdpfevzqcysx Ancja - stacker Almab with 9 cassettes - Pack press

Condition: used, Speed: 0 - 80 m/min, Heads: 7, Planing height: 100 mm, Description: With electric box and hydraulic station. Planer Waco HM200X is used for longitudinal processing of solid wood, which results in such products as MDF panels, plastics or similar types of materials. The Waco HM200X has thirteen different stations that can be adapted to different planing modes. Lodpogrizvjfx Ancsaa In addition to standard equipment such as feeders, top and bottom cutters, side cutters, the machine also has starting blocks, auxiliary feeders, flat cutters, a bevel side cutter, a cutter block and a universal cutter. The maximum working width is 200 mm and the working height is 100 mm. The feed speed can be set in a stepless range from 0-40 or 0-80 m / min. The feeder is equipped with three upper and three lower drive rollers.

Year of construction: 1998, condition: ready for operation (used), A Construzioni Macchine Legno s.r.l. multirip saw is available. Saw blade diameter min./max.: 250mm/360mm, saw blade inner diameter min./max.: 70mm/95mm, cutting width: 320mm, cutting height movable/rigid: 90mm/120mm, weight: approx. 3000kg. On-site inspection is possible. Lsdpfewv Umwsx Anceaa