Bolster plate

UNBEKANNT / UNKNOWN

Condition: good (used), Cast iron bed - Floor Plate Useful surface (L x W x H): 3600 x 1200 x 300 mm 4 T-slots: width 44 x 26 mm Equipped with Levelling feet Dodpfsh Auahox Ab Tewf Weight: approx 3 T

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape Dsdefg E Hpopfx Ab Towf automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: used, Aufspannplatte - Tisch einer Langhobelmaschine - Tischbreite/Aufspannbreite: 1845 Tischlaenge/Aufspannlaenge: 5505 mm Dwodpjbn Amfefx Ab Tof 7 T-Nuten laengs fuer T-Nutensteine: M 30 T-Nutenabstaende zueinander: 263 mm Gesamtlaenge: 6230 mm Plattenhoehe insgesamt: 350 mm Gewicht: 11 t

Condition: good (used), Year of construction: 2002, functionality: fully functional, USED Soraluce Soramill Model SP 10000 Travelling Column, Table Type CNC Milling Centre, with Automatic Oil Mist Lubricated Orthogonal Milling Head with 1 X 1 Degree Indexing and HEIDENHAIN TNC 430 M Control System. Year 2002 SN 8647 Table Area - 10000 x 1100 mm Column Traverse (X) - 8500 mm Vertical Traverse (Y) - 1600 mm Ram Traverse (Z) - 1200 mm Spindle Motor - 28 kW Spindle Taper - Standard ISO 50 BT50 tooling Pullstud - DIN 6987 2-Form A. ISO 7388/2-Form A Independent Gearbox with 2 Ranges Speed Range - 20 to 4000 RPM Feed Range - 5 to 5000 mm/min Rapid traverse rate - (X, Y, Z) 15,000 mm/min Preloaded double nuts and recirculating ballscrews to each axis. Linear Guiding System with recirculating cylindrical rollers and steel guideway assemblies in X, Y and Z axes Independent A.C Drive motor to each axis. Linear Transducer in X, Y and Z-axes with air purge system. Automatic tool clamping. Automatic hydraulic tool releasing device. Dodpfor Hr Arjx Ab Tewf CNC Control HEIDENHAIN TNC-430-M. (Flat TFT screen with digital drives) 9 axes CNC and 1 spindle, 5 of them simultaneously interpolated. Working area lighting Electrical cabinet cooling system Electrical cabinet lighting Heidenhain HR410 portable electronic handwheel with 3m spiral cable Horizontally articulated pendant for CNC control Orthogonal head 28KW, 800Nm, 1deg x 1 deg, 4000rpm oil lubricated Price includes oil cooling unit for both head and gearbox. Option G2, Ram prepared for 4000rpm, is also included. Coolant through the spindle type AD. Coolant system with 500l capacity tank with two pumps providing low and high pressure of 3 and 8 bars and 50l/min flow. The system includes a combined paper and magnetic drum-filtering unit. Standard operators platform fixed to the column 40 tools capacity toolchanger magazine, BT50 Max. Tool length = 400 mm. Max. Tool diameter: - With full magazine = 120 mm. With adjacent position empty = 250 mm. Max. Tool weight = 20 kg. Mean tool weight with full magazine = 10 kg. Max. Permitted total weight = 20 kg. Swarf Conveyor Hinge type conveyor belt Machine preparation for the addition of a 4th axis electro-mechanical table. Splash Guarding against swarf at the table front and both sides. Consists of four sliding front doors with a height from the floor of 2.100mm and a length of 1.700mm each one. Manually operated opening and closing with mechanical interlock. The doors can be opened for the full longitudinal traverse. The rear of the table is open. Protection in the back and both lateral sides of the machine column.

Condition: used, Year of construction: 1990, functionality: fully functional, machine/vehicle number: 07-16 1990, travel distance X-axis: 2,000 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 800 mm, A machine in good condition, as shown in the pictures, manufactured in 1990 and equipped with NCT 90 control. It has been used very little and is being sold due to underutilization. The total weight of the machine is 33 tons. The machine is fully operational. Disassembly and transportation are the responsibility of the buyer. Dwjdpfx Absw Sx Agj Tsf

Condition: used, Year of construction: 1996, functionality: fully functional, travel distance X-axis: 10,000 mm, travel distance Y-axis: 2,600 mm, travel distance Z-axis: 700 mm, Manufacturer: PAMA Model:SPEEDRAM 1 CNC Year1996 Spindle:140mm. Tranversal travel:10.000 mm. Vertical travel:2.600 mm. RAM travel:600 mm. Ram Size: 360x320 Spindle travel:700 mm. Spindle taper:ISO 50 Spindle motor power:50 Kw. Spindle speeds: 6 ÷ 2000 Rpm. Cnc:CNC Selca 3045 ATC: 60nos. Total weight:65 Tons. Dsdpfx Abjwzh Aps Towf Features and Accessories Complete with: - n. 1 automatic universal milling head - n. 1 Floor plate 6000x2500x300mm -n. 1 Floor plate 4500x2000x300mm - Rotry Table 2000x1600 with long travel 2000mm -Loading capacity on table:15ton - levelling shoes

Condition: good (used), Year of construction: 2004, Steuerung: Siemens 840-D Verfahrweg X: 6000 mm Verfahrweg Y: 3000 mm Verfahrweg Z: 1000 mm Verfahrweg W: 700 mm Spindeldurchmesser: 150 mm Spindeldrehzahl: bis zu 2800 U/min Spindelleistung: 51 kW Werkzeugwechsler: 80 Werkzeuge Vertikalfräskopf CNC-Rundtischgröße: 2000 x 2500 mm Dwjdpjxn R Ncofx Ab Tjf Tischverfahrweg V: 1500 mm Tischtragkraft: 25 t 2 Stück Bodenplatten Späneförderer Automatischer Kopfwechsler KF-D4 vertikaler Einachsen-Fräskopf, 2,5° programmierbar

Condition: used, Technical details: Dedpfxou N D Rqe Ab Tswf table length: 3600 mm table width: 3600 mm table load: 50 t table travel: 2000 längs / longitudinal mm table height over floor: 1350 mm table speed: ca. 1000 mm/min table rotating: 360 ° total power requirement: 14 kW weight of the machine ca.: 38,5 t dimension machine xH: 5,5x3,7x1,4 m space requirements of the machine approx.: 6,2x3,7x1,4 m Main areas of application: -Multi-sided machining -Supplement for travelling column milling machines or boring mills Electric and mechanics of the Rotary Table have been overhauled. - newly equipped with a digital measuring system (DRO) for x-travel and rotation - control via control panel - table clamping plate 14t weight - table load capacity 50t 11 pcs T-slots according DIN 650: - a=42mm - h=75mm - b=70mm - c=31mm Rotary Table can be inspected under power! Following work has been proceeded: - Integration of a Digital Read Out (DRO) for the x axis and a rotary encoder for C-axis - integration of a control via a control panel - renewal of hydraulic pipes / hoses, screw connections, manometers, flow chokes and filters - bearing of both axis transmissions - control cabinet and complete machine cabling has been renewed - end positions cleaned, checked, adjusted and defective replaced by new ones - frequency converter for continuous speed retrofitted - preparation of the necessary documentation (operating instructions, electrical and hydraulic diagram) - cracked gearbox housing repaired via casting lock - renewal of the guideway wipers - processing of the guideway cover including new wipers - machine has been repainted - renewal of axis drives - feed gear cleaned and resealed - feed motor new bearing installed *

Condition: used, Year of construction: 1980, table load: 60,000 kg, table width: 3,500 mm, travel distance X-axis: 2,500 mm, table length: 3,500 mm, Hydrostatic table Heidenhain ROD encoder for rotation Controlled using Siemens 840C CNC Table Length: 3500mm Table Width: 3500mm Table load: 60000 Movement V-axis:2500mm Rotation B-Axis:720° Length: 6000mm Width: 3500mm Djdpfx Abjuxnzro Tswf Height: 1400mm Weight: 42000kg

Condition: used, Year of construction: 1995, travel distance X-axis: 10,000 mm, travel distance Y-axis: 2,600 mm, travel distance Z-axis: 600 mm, spindle speed (max.): 1,950 rpm, feed length W-axis: 700 mm, quill diameter: 140 mm, cnc SELCA 3045 X AXIS STROKE 10000 MM Y AXIS STROKE 2600 MM Z AXIS RAM STROKE 600 MM W AXIS QUILL STROKE 700 MM SPINDLE DIAMETER 140 SPINDLE CONNECTION ISO 50 SPINDLE MOTOR POWER 53 KW ROTATION SPEED 6 - 1950 MM ROTARY TABLE TABLE 2000 X 1600 MM CAPACITY 10 TON STROKE AXIS V 2100 MM AUTOMATIC BI-ROTATIVE HEAD UNIVERSAL TUAR 25 Dsdpfx Abownqnuj Tjwf PICK UP HEADS INTERNAL AND EXTERNAL COOLANT 60-Place TOOL CHANGE CHIP CONVEYOR ANCHORING PLANE 2500 X 6000 MM HYDROSTATIC X-AXIS RAM WITH HYDROSTATIC GUIDE ON 4 SIDES