CNC processing centre windows & doors

SCM Windor NT 1

Condition: new, Year of construction: 2024, carrying capacity per cantilever arm: 500 kg, shelf height: 3,200 mm, total length: 2,100 mm, total height: 3,200 mm, axle spacing: 1,000 mm, load capacity per stand: 2,500 kg, Cantilever rack in hot-dip galvanized design: Scope of delivery: 3 rack stands, height 3.2 m with base section, 1.8 m usable depth (2 m total depth) 12 cantilevers with 1.8 m usable depth (for chipboard with approx. 2.1 m depth) Longitudinal and diagonal struts for 4 m rack length (distance 1.3 m) Fastening material (screws, nuts and washers) Net price: €2,490.00 plus VAT Detailed description: - Stable steel construction made of IPE profiles (screw system) Djdpsqt Dmysfx Acfokp - Rack height 3,200 mm - Load capacity per stand 2,500 kg - Base section and cantilevers with 1,800 mm usable depth - (for 2,100 mm chipboard depth) - Cantilevers height adjustable in 100 mm increments - 4 screwable screws per stand Cantilever arms, standard (= 5 storage levels) - Load capacity per cantilever arm 500 kg - Including longitudinal and diagonal braces for 1,000 mm spacing - Shelf length = 2,100 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Made in Germany - Short delivery time Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Delivery for stock items can take place in approx. 1 week after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: refurbished (used), DIFFERENT TYPE OF MOTOR AND SLIDE for CELASCHI DET Dodpodvlcyjfx Acfekp SECOND-HAND, FULLY RECONDITIONED

Condition: new, Glass bead nailer "2 P Jumbo automatic E.C." - new - Your advantages: Dsdjvnh T Njpfx Acfjkp - The corner connections are closed - No open glazing bead joints - There are no color differences when painting - The glazing bead frames are easy to assign Clamp corner joining machine 2P Jumbo Automatic E.C. for clamping glazing bead frames. Choice between automatic and manual operation; With angle system, clamping device from above and front Pressure can be regulated separately. Inserting parallel and superimposed ones Clamps possible via electronic programming control. Stapler can be mounted on a suitable work table, Operation via foot valve. ----- Price in this version on request! Plus packaging/shipping ----- Pictures show Clamp corner joining machine 2P inlcuding the option of movable work table (please find details as follows under additional prices) Additional prices: ----- Movable work table height adjustable from 700 - 1000 mm, 2 pieces of support bars can be plugged in 1000 mm long, 2 pieces swiveling and sliding Support bars 1000 mm, support bars covered with felt, 4 swivel castors, 2 of which have a stop device. ----- Additional price: 1.311,00 euros net Brackets: packages 15 mm brackets (package of 2000): Price 22.00 euros 12 mm brackets (package of 3000 pieces): Price 32.00 euros 10 mm staples (package of 3000 pieces): Price 32.00 euros Dimensions and weights ----- Jumbo Automatic E.C 470 x 370 x 300 mm, 35 kg Work table 32 kg All prices net. plus statutory VAT Ex works plus packaging and shipping (technical data according to manufacturer - no guarantee!)

Condition: used, machine/vehicle number: 008186, Max. panel width: 3200 mm Max. panel length: 3200 mm Main saw blade projection: 110 mm No of Grippers: 11 Dkodpfxjxaudzj Acfjp

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: HaRo2020, total width: 800 mm, total height: 1,100 mm, total length: 1,200 mm, briquette diameter: 60 mm, overall weight: 300 kg, warranty duration: 12 months, type of input current: AC, input voltage: 400 V, power: 3 kW (4.08 HP), Equipment: emergency stop, Our new HaRo2020 briquetting press, with a capacity of up to 40 kg/h, automatic tongs, and pre-compactor, is manufactured by ourselves. You can only purchase this machine directly from us, as we do not use intermediaries. The briquetting presses are CE-compliant and manufactured according to the latest standards. Since we produce most of the components in-house, we can offer the machine at a particularly competitive price. Price is exclusive of VAT. The new hydraulic unit is equipped with a SILENCE-PUMP, making the machine extremely quiet in operation. Another benefit of the helical gearing in the pump is increased durability. Everything is made in Germany! You are welcome to visit us and test the machine with your own material. Dkjdpfsw A Hvdox Acfjp When purchasing our briquetting press, you will receive a detailed and comprehensive German (PDF) operating manual for this machine. The input material must have a moisture content below 15%—ideally 10 to 12%—for sawdust and planer shavings. Technical Data – Hydraulic unit: 3.0 kW (connected load) – Power consumption per hour: approx. 1.8–2.0 kWh – Throughput: approx. 15–40 kg/h – Voltage: 400 V – Frequency: 50 Hz – Circuit protection: 16 A plug – Power cable length: 3 m – Hydraulic control with Bosch Rexroth valves – Briquette diameter: 60 mm (length varies according to material) – Motor equipped with motor protection switch and emergency stop—for operator and machine safety, including motor protection – No electronic components prone to failure such as controllers, sensors, or complicated electronics – Pressing without additives – Counter-pressure adapts fully automatically to your material – Thanks to the pre-compactor, bulky shavings are no problem – No adjustments or monitoring of the pressure required – Fully automatic operation Spare parts supply is guaranteed, as we manufacture the machines in small series in our facility in Germany. The large oil tank ensures that the oil will not overheat during continuous operation. Machine dimensions: Length: 1.25 m Width: 0.82 m Height: 1.11 m Feed hopper: Diameter approx. 80 cm x height 60 cm Weight: 300 kg The briquetting press is immediately operational and does not require installation—just plug it in and start working. The machine can be viewed and tested on-site. You are welcome to send us a sample of your material for testing; we find this is the most effective method.

Condition: as good as new (ex-display), Number of spindles 6 St. Working width 250 mm Working height 150 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 6-24 m/min. weight 4770 kg Dimensions (L/W/H) 4722x1860x1776 mm Dkjdpfx Aevnv Ubocfep Vierseitenhobelmaschine Kuper SWT XL-6 in Fenster-Version mit elektronischer Axial- und Radialverstellung der Spindeln. Schwerer Maschinenständer, verwindungsfrei und schwingungsarm. Anzahl der Spindeln: 6 Arbeitsbreite: 250 mm Arbeitshöhe: 150 mm Abrichttischlänge: 2500 mm Spindeldrehzahl: frequenzgeregelt 4.000 - 8.000 U/min Vorschubgeschwindigkeit: 6-24 m/min Ausführliche Beschreibung finden Sie in nebenstehender PDF-Datei! (Technische Angaben laut Hersteller - ohne Gewähr!)

Condition: excellent (used), Year of construction: 2013, operating hours: 3,000 h, 5-axis CNC portal machine; Console table with 6 movable consoles, each with 2 suction cups, side and longitudinal stops, LED position display for vacuum suction cups Venture 316 Future Package 10 extraction rails, Power-Clamp connection, vacuum connection for templates Dsdpfjy E Npfsx Acfokp WORKPIECE PARAMETERS: – Maximum workpiece length: All units, single operation: 3300 mm; pendulum operation: max. 1740 mm Tool diameter 25 mm: single operation: 3475 mm; pendulum operation: max. 1915 mm – Workpiece width: Front stop: 950 mm all units / 1050 mm with tool diameter 25 mm Rear stop: up to 1400 mm / 1550 mm – Workpiece thickness: – Max. 250 mm including clamping devices – Up to max. 60 mm with standard clamps SAFETY AND PROTECTIVE EQUIPMENT: EC-compliant; Safety enclosure on the right with door Left and rear: wall installation! Equipment: 10 kW Drive5C spindle and 14-position tool changer (carousel) + 9-position linear changer (side mounted) Drilling head with 16 spindles (V12/H4/S0/90°) DRIVE5C+ interface for aggregates Tool length measuring probe Software for position measurement and CNC coordinate rotation Tool transfer station Coolant tank for processing spindle Vacuum pump 300/360 m3/h Powerclamp pneumatic package Control system: POWERCONTROL PC85 with POWERTOUCH system; IPC POWERPACK Operator terminal for program start; camera system with tablet PC WOODWOP CAD/CAM standard interface Documentation and control texts: German Delivery includes only the tools and HSK tool holders shown in the images!

Condition: excellent (used), Year of construction: 2018, Weinig production line CONTUREX C 125, year of manufacture 2018 Dsdpoy Emrksfx Acfekp

Year of construction: 1998, condition: excellent (used), Kap Saw Reinchardt NC 700 automatic Manufacturer Reinchardt Model / machine type NC 700 Year of production 1998 Machine category Kapła Kapowa Location Gorzów Wlkp. Conditions of delivery OWN RECEIPT Cost of delivery Dkedpfjd H Hmhox Acfsp Customer cover Start type to be agreed Description Comments CUTTING SAW FOR CUSTOMIZED DIMENSIONS, ACCURACY UP TO 1MM, NEW CONTROLLER, SAW BLADDER BY HYDRAULIC AGREEMENT

Condition: excellent (used), Year of construction: 2019, Maximum swing range (vertical axis of the electric spindle): 1650 – 2350 – 3000 mm Vector speed (X-Y) (PRO-SPEED): 85 m/min Programmable speed in Z-axis: 30 m/min Element passage: 170 mm Multifunction device BRC-K: Technical specifications (Gr-Multif_BRC-K_2.1_N5.1-0.6) 1) Performance: Dkjdpfsyffh Nex Acfop Motor 3.6 kW (S6 - 40%) Number of poles: 2 Speed control: via CNC with frequency inverter Cooling system with fan 3) Horizontal milling spindle: Tool holder: ER25 Spindle speed: 6000–18000 rpm Rotation direction: clockwise/counterclockwise Max. tool dimensions: L1 = 151 mm / W1 = 120 mm / D = 20 mm Max. tool dimensions 2: L2 = 111 mm / W2 = 80 mm / D = 20 mm Max. machining depth: 115–75 mm