Shredder 4 shaft

Recycling Shredders & Solutions RSS 4 shaft shredder

Condition: excellent (used), Catalog number 6726 TECHNICAL DATA - Loading hopper inlet 280x300 mm - Discharge outlet for chipped wood Ø 310 mm - Rotor working width 340 mm - Main motor 22 kW - Number of knives 6 pcs - Dimensions (L/W/H) 1300x1150x1680 mm - Weight 720 kg ADVANTAGES – very good condition – used wood chipper Njdpfsignt Ujx Afasla Net price: 19,900 PLN Net price: 4,740 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR (In case of significant exchange rate fluctuations, the price may change)

Condition: new, Year of construction: 2025, pressing force: 38 t, power: 5.5 kW (7.48 HP), New on stock Nodpfx Afjwhfu Ajaola Avermann MPC 20 PEL Optional with Bin Lift

Condition: ready for operation (used), Rotary atomizer, nominal process gas flow rate: approx. 100 kg/h, water evaporation capacity: between 0.5 and 6 kg/h, inspection by appointment. Njdpfxev Edwrs Afaela

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: Nljdpfxowp Rqfs Afaoa • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: used, functionality: fully functional, Year of construction: 2021, operating hours: 116 h, load capacity: 4,000 kg, lifting height: 17,000 mm, fuel type: diesel, mast type: telescopic, power: 85 kW (115.57 HP), empty load weight: 13,040 kg, drive type: Diesel, Rigid telescopic forklift Mast type: Telescopic Speed class: 20 Technical condition: New Front tires type: Air Front tires Size: 400/70-24 Front tires Condition: 80 - 100% Rear tires Type: Air Nlsdpfx Asv Ezt Djfaja Rear tires Size: 400/70-24 Rear tires Condition: 80 - 100% 3rd valve, 4th valve, heating, full cabin, CE certificate, Specifications: -Carrying capacity 4000kg -Lifting height 16,4m -MAX gradeability 40% -Curb weight 13040kg -Engine KUBOTA 85,1kw ( 114hp ) -Capacity 3769cm3 -Emission standard Tier4f -Steering Front wheel steering, all wheel steering and crab steering.

Condition: excellent (used), Year of construction: 2017, operating hours: 144 h, functionality: fully functional, machine/vehicle number: 694355, overall weight: 235 kg, load capacity: 16 kg, arm reach: 1,610 mm, This is a KUKA KR 16-2 R1610 industrial robot Year of manufacture 2017 Nsdpfx Aet N Szpefasla We are also happy to offer you this robot overhauled! The robot includes the following options: BoardPackage EthernetKRL LoadDataDetermination Profinet KRC-Nexxt RemoteService SafeOperation UserTech

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit Nledpfx Afoh Hm Thjaoa -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: like new (used), “Hazemag Universa 1620” for Sale Nodpfxeggflvo Afaela Manufacturer: Hazemag Type: Universa 1620 Rotor size: 1.600 x 2.000 mm Inlet size: 2.500 x 2.000 mm

Year of construction: 2024, condition: new, The rolls cruhser RC 200 is ideally suited for crushing medium-hard, brittle, hard samples like coal, ore, slage, minerals, graphite and many more. Nlodpef Ulycofx Afaja Max. feed size*

Condition: used, Year of construction: 2017, operating hours: 854 h, total width: 2,450 mm, total height: 1,100 mm, total length: 1,900 mm, Empty weight: 800 kg Price: On request - Year: 2017 - Documentation available: No Nledpfx Aexan Utsfaoa - CE marking present: Yes - CE certificate present: No - Serial number: 5037411-000150 - Operating hours: 854 - Transport dimensions: 1900mm x 2450mm x 1100mm (l x w x h) - Transport weight [kg]: 800kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels