Presto screw press SPS15 + container

Presto SPS15

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres Godpfx Ageu Thhrs Dsca PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2022, operating hours: 0 h, condition: new, Mobile cleaning centrifuge including buffer storage for dirty water, agitator and double membrane compressed air pump. - new machine - numerous other variants and special designs on request Machine type: Process water centrifuge solid-liquid Manufacturer: Eurotec Innovation GmbH Model: ZS21-M EUR Application: vibratory finishing technology, general solid-liquid separation, cooling lubricant processing, wet blasting systems, ... Benefits: - High discharge through acceleration forces acting in the system of over 1800 times the acceleration of gravity - Management of the process water in a circuit, which minimizes operating costs and protects the environment Gedpfxof Sqfqs Ag Deca - Saving of expensive additives for the vibratory grinding process (compound) - Economical and efficient separation of solid particles from a mixture - Economical and efficient separation of solid particles from a mixture - Suitable for process liquids up to 70 ° C (optional cooling available) - frequency-controlled motor drive for smooth acceleration and braking of the rotor Are you looking for innovative solutions for surface treatment and process water treatment? We offer a wide range of systems in the field of vibratory grinding, drying and process water technology, which are precisely tailored to your application. From development to production: We deliver all of our products from a single source and everything is "Made in Germany". ----- Please just contact us, we will be happy to advise you without obligation. ----- The European Commission provides a platform for out-of-court online dispute resolution (OS platform). The offer serves exclusively as an internet presentation of our goods. The contract negotiation comes about by means of telecommunication (email, fax, telephone, news portal), where we first make you a non-binding offer, in which we inform you about our general terms and conditions and the right of withdrawal with imprint before the purchase / contract is concluded.

Year of construction: 2015, condition: new, Hydraulic magnets are supplied with built-in magnet generator, so that only the hydraulic connection is required. ON/OFF switching and demagnetization are triggered by hydraulic flow. Gjdpfx Agjc Spgle Djca We have different sizes and capacities in stock NEW and USED

Condition: good (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Gcjdpfx Ajic Rl Dsg Doa Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8t The hydraulic unit is functional, the drive motor is in the removed state.

Condition: good (used), For Sale: GEA Laguilharre 4-Effect Evaporator – High-Efficiency Industrial Solution Are you looking for a powerful and reliable evaporation system for your production process? This GEA Laguilharre 4-Effect Evaporator is the perfect choice! Specifications: ✔ Manufacturer: GEA Laguilharre ✔ Model: 4-Effect Evaporator ✔ Condition: Used ✔ Stock Number: 900 ✔ Machine Type: Evaporator ✔ Stages: 4 ✔ Water Evaporation (skimmed milk): approx. 12,000 kg/h ✔ Tube Diameter: 51 mm Godpfx Agjv T Rf Ss Doca This high-quality evaporator is ideal for dairy, food, and chemical industries. The 4-effect technology ensures maximum energy efficiency, leading to lower operating costs and higher productivity. Interested? Contact us today for more information or to schedule a viewing!

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, machine/vehicle number: WKZ45-1030, CLEARANCE SALE, STOCK MACHINE! We invite you to visit our technical center to experience the quality and functionality for yourself. Material Shredder 45KW Hopper opening: 1,030 x 1,235 mm Rotor diameter: 360 mm Star-delta start, automatic shut-off during idle - Hydraulic pusher equipped with pressure plates - Siemens PLC control - Optionally with control cabinet extension for discharge conveyor belt and overband magnetic separator Complete solution with discharge conveyor belt in any configuration. Our core competence lies in delivering exactly what the customer truly needs. We work together with our customers to develop customized, individual solutions and supply corresponding systems from our own production. Please feel free to contact us by phone to find the right solution for your application. Conveyor belt, conveyor system, discharge belts, belt conveyors, magnetic separators, overband magnetic separators, recycling, wood chips, plastics, metal-free, metal detection, neodymium, overband magnet, magnetic belt separator, lifting magnets, filter rods, magnetic grids, magnetic grate, metal separator, block magnet, filter systems Gcjdpsv Tdq Iofx Ag Doa All prices are net prices plus 19% VAT All information provided without guarantee, while stocks last!

Condition: used, Year of construction: 2016, operating hours: 25,046 h, Used Blow Molding Machine KRONES Contiform C312 PRO Year 2016 Introducing the Blow Molding Machine KRONES Contiform C312 The KRONES Contiform C312 PRO blow molding machine, manufactured in 2016, represents the pinnacle in the bottling industry. Crafted by the renowned German company Krones, this model delivers reliable, high-quality performance to meet the most demanding sector requirements. Performance and Capacity of the Machinery Featuring a 12-cavity mold, the Blow Molding Machine KRONES Contiform C312 operates at a maximum speed of 27,000 bottles per hour (bph). This remarkable production speed ensures a steady, efficient flow, thereby optimizing processing times and maximizing productivity. Versatility and Adaptability of the Blow Molding Machine KRONES Contiform C312 Moreover, its ability to adapt to various product types, including square and round shapes, makes the Contiform C312 PRO highly versatile. This feature facilitates a wide range of applications in the bottling industry, offering operational flexibility and production diversification possibilities. Structural Solidity and Durability Weighing 25.0 tons, the machinery is built to withstand the continuous demands of the production environment. Its solid, reliable structure ensures long-lasting performance, consequently minimizing downtime and ensuring uninterrupted production. Efficiency in Material Handling Gsdpfxevgu Eij Ag Dsca Additionally, equipped with a tilter with a maximum capacity of 2.0 tons, the Blow Molding Machine KRONES Contiform C312 enables high efficiency in material movement and handling. This feature optimizes logistical processes within the company, thereby reducing loading and unloading times and enhancing overall operational efficiency. Advanced Technology and Optimal Performance Furthermore, the 150 kW blowing system ensures excellent material distribution, thereby guaranteeing the formation of perfectly shaped bottles free from defects. Additionally, the machinery is fitted with a 5 kW air conveyor and offers an air flow rate of 14㎥/h at 11°C and 1,100㎥/h, ensuring a constant, reliable flow during the production process. Concluding Remarks on the KRONES Contiform C312 PRO In conclusion, the Blow Molding Machine KRONES Contiform C312 stands out as the ideal choice for those seeking a high-quality used blow molding machine. With its robust construction, reliable performance, and advanced technology, this model offers an efficient and cost-effective solution for the most demanding bottling needs.

Year of construction: 2006, condition: like new (used), Container volume 32 m3 Gcsdpefhb Tkefx Ag Dea

Condition: like new (used), Year of construction: 2023, operating hours: 95 h, functionality: fully functional, total width: 2,950 mm, total length: 6,200 mm, total height: 4,530 mm, overall weight: 6,200 kg, belt width: 1,500 mm, fuel: electricity, input frequency: 50 Hz, type of input current: three-phase, input voltage: 400 V, transport height: 2,350 mm, transport length: 6,030 mm, transport width: 2,250 mm, Equipment: documentation/manual, Westeria mobile air separator type AirLift move for the separation of heavy and light materials. Typical applications in the recycling / waste management industry, for example for separating film from compost (fine or coarse grain) and mixed construction waste. Throughput capacity between 100-150 m³/h depending on material properties Working width: 1500 Color: RAL 3020 C3M Gcsdpsvrcigefx Ag Doa RAL 7040 Including - DiscSpreader for optimum material distribution in the separator process - Pipe for blowing the lightweight material into on-site containers

Condition: reconditioned (used), Year of construction: 2005, Coupling containers, 30–32 m³, suitable for screw compactors, available for right or left configuration. Used, fully functional coupling containers from €4,000, depending on condition, excluding VAT. Delivery possible. Gcjdpegypd Hefx Ag Dea