Used Zero Point for sale (5,272)

Condition: used, Weiss   Weiss Technik TS 60 Thermal Shock Test Chamber / 60 L, –71…+220 °C Water-cooled   Item description:   For sale is a Weiss Technik TS 60 thermal shock test chamber. The chamber is ideally suited for rapid temperature cycling tests (e.g., according to IEC, MIL-STD, JEDEC) and has been well maintained.   Volume & Internal Dimensions:   Test volume: 60 liters   Internal dimensions of basket / test chamber (W × D × H): approx. 380 × 430 × 370 mm External dimensions (W × D × H): 895 × 1970 × 1895 mm   Temperature ranges & cycling   Hot chamber +50 °C to +220 °C Cold chamber −72 °C to +70 °C   Transfer time (basket between both zones): < 10 seconds   Heating rate / heating speed up to 17 °C/min Cooling rate / cooling speed up to 3.7 °C/min   In single mode (cold zone only), heating rate: approx. 3.2 °C/min   Temperature deviation & homogeneity   Temporal deviation (temperature control over time): ± 0.3 to ± 1.0 °C   Load / payload & lifting system   Basket / lifting system load: 20 kg maximum load capacity Transfer basket secured by protective grilles on all sides   Other features & equipment Hjdozii A Rspfx Ag Eefn   Noise level: approx. 58 dB(A) during operation Control: Touchscreen, RS-232 / USB / Ethernet interfaces   Electrical connection: 3/N/PE AC 400 V ±10% 50 Hz Rated power approx. 8.5 kW Rated current approx. 25 A Fuse on customer's side 32 A Refrigerant R-404A / R-23   Weight: 800 kg   For your safety as a buyer, please note the following:   The following points will be carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, new filling with legally compliant refrigerant 3. Leakage test with certificate 4. After successful inspection, the chambers will be subjected to a documented test run.   Condition: used   Scope of delivery: (See image)   (Changes and errors in the technical data are subject to change!)   We will be happy to answer any further questions you may have by telephone.

Condition: used, Binder BINDER KB 720 Cooling Incubator with P Plus Package – Battery Test Chamber, EUCAR 5, CO₂ Extinguishing System Device description: For sale is a BINDER KB 720 (E6) cooling incubator, manufactured in 2022, equipped with the extended safety and performance test package "P Plus". This device is not a standard laboratory incubator, but a high-quality safety test chamber, specifically designed for aging, performance, and safety tests of lithium-ion energy storage systems. Special added value: The device is designed to safely detect, monitor, and contain critical battery events – up to EUCAR hazard level 5 (fire/flames, no explosion). What can the device do specifically? (Point 2 – Performance & Application) Performing aging tests on lithium-ion cells Performance tests (charge/discharge cycles at varying temperatures) Temperature endurance tests and temperature change tests Tests of unpowered and cyclically powered cells Reproducible, precise temperature control throughout the usable space Safe execution of tests under realistic thermal conditions Test environment for R&D, automotive, e-mobility, and energy storage technology Suitable for: Battery & cell manufacturers Research and development laboratories Testing laboratories & safety testing Automotive / e-mobility / energy storage The P Plus package turns the KB 720 into a genuine battery safety test chamber: Integrated safety functions: Automatic & manual CO₂ fire extinguishing system Smoke detector with optical & audible alarm Mechanical double-door locking system (secure containment) Spark protection in the interior Exhaust port with reversible overpressure valve Connections for external inertization (e.g., nitrogen) Emergency stop / manual triggering of the extinguishing system Feedthrough openings for charging and measuring cables Result: The device is designed for tests on lithium-ion cells up to EUCAR hazard level 5, where fire or flames may occur without resulting in an explosion or uncontrolled propagation. Not an abuse or destruction test device, but a safe, standard-compliant test chamber for real operating and failure scenarios. Technical key data: Temperature range: -10 °C to +100 °C Interior volume: approx. 698 liters Inserts: 4 x stainless steel Max. load per insert: 45 kg Max. total load: 100 kg Electrical data: Mains connection: 200–240 V AC Frequency: 50 / 60 Hz Phase: 1-phase Power consumption: approx. 2.1 kW Fuse rating: 16 A Refrigerant: R134a Protection class: IP 20 Hfsdpozizr Rjfx Ag Ejn Dimensions & weight: External (W × H × D): approx. 1250 × 1950 × 900 mm Internal (W × H × D): approx. 970 × 1250 × 576 mm In short – why this device is special genuine battery safety test chamber suitable for EUCAR hazard level 5 integrated CO₂ extinguishing system large chamber (≈700 l) high market & resale value Weight: approx. 285–300 kg Documents & Downloads Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: new, empty load weight: 3,020 kg, maximum load weight: 11,380 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,480 mm, suspension: steel, tire size: 205/65 R 17,5, color: other, gearing type: other, front tire size: 205/65 R 17,5, rear tire size: 205/65 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Loading height approx. 820 mm, vehicle interior width approx. 2,480 mm, front panel made of galvanized steel, 600 mm aluminum side boards, foldable and removable, removable stakes, 40 mm wooden floor, 3 stake pockets in the center for plug-in stakes 80 x 80, 6 lashing eyes, outer frame with lashing points, reinforced gearbox support with load and fast-travel mode, contour marking and side impact protection, fenders and spray suppression at the rear, surcharge for front panel grille 1,600 mm high (perforated sheet metal), price: 1,400 euros, surcharge for aluminum ramps, load-bearing capacity per pair 8 tons, and 2 x folding supports at the rear, price: 1,900 euros, -- subject to printing errors, mistakes, and changes, sample images --, more data under: !, More Details: ! Hfodpfxjz Sydio Ag Een

Condition: new, empty load weight: 2,900 kg, maximum load weight: 7,600 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,480 mm, suspension: air, tire size: 235 / 75 R 17,5, color: other, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Loading height approx. 860 mm, vehicle interior width approx. 2,480 mm, front panel made of galvanized steel, 600 mm aluminum drop-side panels, foldable and removable, 3 central stake pockets for 80 x 80 stakes, removable stakes, 6 lashing eyes, outer frame with lashing points, reinforced transmission support with load and fast gear, contour marking and side impact protection, mudguards and spray suppression at the rear, surcharge for 1,600 mm high front panel grille (perforated sheet metal), price: 1,400 euros, surcharge for aluminum ramps with a load capacity of 9 tons per pair and 2 x folding supports at the rear, price: 1,900 euros, -- subject to printing errors, errors and changes, sample images --, more details at: ! Hjdpfxoz Syf Tj Ag Esfn

Condition: new, empty load weight: 10,500 kg, maximum load weight: 29,500 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, suspension: air, tire size: 235/75 R 17,5, color: other, gearing type: other, front tire size: 235/75 R 17,5, rear tire size: 235/75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, 2 pairs of wheel recesses with covers, axle load scales, total loading platform length approx. 10,250 mm, lowbed approx. 7,150 mm long, loading height approx. 890 mm, 24 x lashing points, each 10 tons, 40 x lashing points, each 3 tons, loading ramps (approx. 3,100 x 760 mm), climbing rail on the outside of the ramps and rear slope, loading ramps adjustable laterally, wooden floor 68 mm thick, storage box with lid for lashing chains or tie-down straps, contour marking according to regulations, rotating beacon, spring-loaded parking brake, incl. axle load displays, vehicle hot-dip galvanized, surcharge for: hydraulic adjustment of the ramps = price: €1,000, -- subject to printing errors, mistakes and changes, sample images --, more data at: !, More Details: ! Hfodpfx Asz Sx Sxsg Ejn

Condition: new, empty load weight: 3,490 kg, maximum load weight: 8,110 kg, overall weight: 11,600 kg, axle configuration: 2 axles, loading space length: 5,700 mm, loading space width: 2,430 mm, suspension: steel, tire size: 355/60 R 18, wheelbase: 990 mm, color: other, gearing type: other, front tire size: 355/60 R 18, rear tire size: 355/60 R 18, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Three-sided tipper, side walls 600 mm high, galvanized, + lattice extension 1,000 mm high, wide tires 355/60 R 18, loading height approx. 970 mm, central locking for side and rear walls, side walls pivoting and foldable, side walls with spring relief, floor made of fine-grained steel 4 mm, 12 x heavy-duty tie-down points recessed in the floor, tipping angle: 50 degrees rearward and 45 degrees sideways, continuously adjustable drawbar height, rear supports pluggable, geared support winch with load and fast gear, front, receiving shaft for two aluminum ramps integrated into the chassis, contour marking according to ECE R 048, surcharge for aluminum ramps, load capacity per pair 10 tons and 2 x folding supports, rear, ramps suitable for steel-tracked vehicles and rubber-tired vehicles, price: 1,900 euros, -- printing errors, errors and changes reserved, sample images --, more data at: !, More details: ! Hjdpfx Agoz Sx Uyj Ejfn

Condition: as good as new (ex-display), Year of construction: 2021, functionality: fully functional, machine/vehicle number: W202001, table length: 800 mm, table width: 550 mm, Equipment: documentation/manual, H-Frame Press – 30 t – Double-column Press – 800 × 550 mm – Versatile Assembly & Production Press For sale: hydraulic double-column press (H-frame press) with a pressing force of 30 t. The machine is highly versatile and can be used as an assembly press, small batch press, hand-loading press, vulcanizing press, or heated platen press. This is an approximately 2.5-year-old, unused machine with zero operating hours, offered with full warranty. Inspection is possible at our warehouse in Ennepetal. ===== Technical Specifications & Information: Hydraulic Double-Column Press – 30 t ==== General Information - Design: Double-column press (H-frame) - Pressing force: 5–30 t (adjustable) - Machine weight: approx. 2,000 kg - Paint finish: RAL 7035 (Light Grey) / RAL 2009 (Orange) ==== Working Area - Table size: 800 × 550 mm (additional variant: 700 × 500 × 70 mm) - Ram plate: 700 × 500 × 80 mm - Max. distance table/ram: 500 mm - Stroke: 500 mm - Front opening width: 820 mm - Table height: 800 mm Hfedpfxou U Ey Ie Ag Esn ==== Speeds - Approach speed: approx. 45–50 mm/sec - Return speed: approx. 40–55 mm/sec ==== Hydraulics - Operating pressure: up to 300 bar - Hydraulic pump: ASC, 28.5 l/min - Motor power: 11 kW - Oil tank: approx. 100 l - Valves: Bosch Rexroth ==== Construction & Guidance - Cylinder: Ø 110 mm (piston), Ø 70–75 mm internal - Guide columns: Ø 50 mm - Ram guided by 2 columns - Robust machine frame - Rear and side guards fully enclosed ==== Control & Operation - Pressing pressure adjustable via rotary control - Adjustable two-hand operation (3 m supply cable) - Position limitation via cam switch - Travel limitation via movable sensors - Automatic positioning to defined stroke points - Resettable piece counter ==== Safety - Light curtain 500 mm (14 mm resolution, finger protection) - Reach-under protection - Optional reach-over protection - Emergency stop switch - Certified safety inspection ==== Equipment - Control cabinet technology from brand manufacturers - Illumination in press workspace - Eject chute in table ==== Options - Heated platens: 500 × 500 mm (up to 200 °C, with controller & timer) - Commissioning & operator training ==== Lead Time & Service - Delivery time: approx. 6 weeks (without heated platens) - Heated platens: approx. 8 weeks - Customer service: Dresden, Hamburg, Ennepetal, Waibstadt, Göppingen, Gelsenkirchen ===== Assembly work, small batch production, forming applications, vulcanizing, hot pressing Hydraulic press, hydraulic press, double-column press, H-frame press, assembly press, small batch press, vulcanizing press, heated platen press, industrial press Are you looking for a hydraulic press customized for your application? Contact us for a tailored offer. Our hydraulic presses are manufactured according to German and European Machinery Directives (Directive 2006/42/EC), EC regulations, and EU safety standards. Additionally, our presses exceed both Canadian and European safety requirements, as they fully comply with the Brazilian occupational safety standard NR 12, which builds upon these regulations. Our core strengths are special machine engineering and press automation. We offer custom-built hydraulic presses at surprisingly attractive prices. The hydraulic systems primarily use components from leading European manufacturers.

Condition: refurbished (used), Year of construction: 1997, functionality: fully functional, drilling capacity: 40 mm, quill stroke: 200 mm, quill diameter: 80 mm, Danumeric 440 overhauled and digitized 2024 Machine version - Work table 1800 x 600 mm with 4T-slots - Boom travel 1050 mm - SK 40 drilling spindle with tool clamping device - Infinitely variable speed programming - Infinitely variable quill feed via three-phase servo motor - 2 T-slots 18 mm on the machine base at the rear - 2 T-slots 18 mm on the left machine base frame - Thread cutting device - Central lubrication - Coolant device - Machine light - CE marking - Safety device - USB interface Dimensions and travels Tool holder SK 40 Column diameter mm 195 Table dimensions mm 1800 x 600 Number of T-slots 4 Distance between T-slots mm 125 Quill stroke (Z-axis) mm 200 Column stroke (W-axis) mm 410 Distance spindle bottom edge - min mm 70 Table top edge max. mm 680 Distance spindle bottom edge - min mm 970 Floor max. mm 1580 Drilling radius mm 540 - 1590 Worktable height mm 900 Cutting values Drilling capacity into solid St 60  40 GG 22  50 Thread cutting St 60 M 36 GG 22 M 42 Main spindle drive AC motor, frequency-controlled kW 5.5 at 100 % duty cycle. Speed range: min -1 15 - 2800 Torque Nm max. 250 constant from min -1 15 - 2000 Feed drives X-axis - AC - servo motor kW 0.25 Y-axis - AC - servo motor kW 0.25 Z-axis - AC - servo motor kW 4.50 W-axis - AC - servo motor kW 2.50 Rapid traverse speeds (X/Y/Z): m/min. 7.5 / 7.5 / 5 Rapid traverse speeds (W): m/min. 3 Feed rates stepless mm/min 5 - 2000 Accuracy Positioning accuracy X-, Y-axis to 1200 mm mm ± 0.075 Electrical data Operating voltage / frequency V / Hz 400 / 50 Control voltage V 24 Hydraulic unit for clamping kW 0.75 Total connected load kVA 13.0 Weight Danumeric 440 (without packaging) with table 1800 x 600 mm kg 2800 CNC control Axes: 4 (X, Y, Z, W), expandable Processor: 32-bit CPU Screen: TFT flat screen, backlit, easy to read from all sides legible from all sides, 215 x 160 mm Position information: Cartesian or polar, absolute or incremental measurements, Unit of measurement: mm or inch or in degrees Interpolation: 2 axes (X, Y) Technology database: tool management, tool suggestions according to machining type, material-dependent cutting data suggestions Tool management: max. 500 tools Subroutine technology: yes Machining cycles Standard software options: Programming in dialog, 38 zero offsets, rotation and mirroring, teach-in for X, Y, Z, restart in program with selection functions for targeted entry Zero point determination: Cycles for determining zero points by manually probing the workpiece for probing the workpiece for: Hfedpfx Aeu Dg D Asg Ejn - any clamped rectangular parts - any clamped round parts - Mediation of cast and flame-cut parts - Angular position detection for round parts by touching reference edges or surfaces Test graphic Graphic display of drilling patterns Data interfaces USB

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, load capacity: 150 kg, stroke length: 1,500 mm, TECHNICAL DETAILS Transfer weight: 150 kg Lift (arms): 1,500 mm MACHINE DETAILS Number of magazines: 2 Capacity per magazine: 12 pallets EQUIPMENT 12 pallets, System 3R GPS 240 with mechanical centering vise SPREITZER MZS 260-125 A 12 pallets, System 3R GPS 240 with mechanical centering vise SPREITZER MZU 170-60 Zero-point clamping system System 3R GPS 240 Hsdpsyfuwgefx Ag Eefn

Condition: ready for operation (used), Year of construction: 2016, operating hours: 400 h, functionality: fully functional, travel distance X-axis: 1,050 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 500 mm, controller model: Siemens 828D, spindle speed (max.): 12,000 rpm, The machine spindle was replaced in 2022! TECHNICAL DETAILS Travel X-axis: 1,050 mm Travel Y-axis: 550 mm Travel Z-axis: 500 mm Milling spindle (BT40): 12,000 rpm MACHINE DETAILS Control unit: Siemens 828D Operating hours: Power-on hours: 26,247 h Hfsdpeyf E Szefx Ag Eon Spindle hours: approx. 400 h (total 4,727 h) EQUIPMENT - Active electrical cabinet air/air cooler - Network connection - USB interface - Spindle chiller - Side windows left and right for large components - Safety cabin with armoured glass - Coolant pump at spindle - Pump for chip flush device - Air at the spindle via M-code function - Operating status light - Oil separator - Electronic handwheel - ICS system (internal coolant supply) - Pump for ICS - 24-position tool changer - Hinge-type chip conveyor, rear discharge - Glass scales including purge air by Siemens - Wireless workpiece measuring system Renishaw OMP60 - Tool measuring system Renishaw NC4 - Automatic machine door Note: The Halter automation system as well as vices including zero-point clamping system are not included in the scope of delivery.

Condition: new, 14 mm M 10 MK 2 230-4.000 U/min. spindle stroke 80 mm throat 190 mm column diameter 65 mm 300x240 mm 2 x 12 x 80 mm 75/357 mm 300x240 mm 2 x 12 x 80 mm Hfedpfxoyv Nqdj Ag Een 437/437 mm feed von Hand Handkurbel Machine height 825 mm total power requirement 0,7 kW weight 93 kg Standard equipment: 5" TFT LCD display with touch function: Manual input of spindle speed setpoint setpoint, actual speed display, integrated drilling depth display with touch zero point transfer, virtual drilling depth scale in the display, machine status status indicators and warnings on the display, Service information, Selectable operator language operator language: DE/EN/FR/ES/IT/NL/RU. - AC motor 230 Volt, 50 Hz - Connection plug ready fitted, cable length 3 m - Infinitely variable speed adjustment via potentiometer - Three separate buttons for clockwise rotation - anticlockwise rotation - stop (spindle stop due to brake function) - Spindle protection with electrical fuse - Mushroom pushbutton (latching) for EMERGENCY STOP - Main switch, lockable - Control voltage 24 Volt - Protection class IP 54 - Paint finish: DD textured paint signal white RAL 9003, PANTONE 7545c, black Item 37.6 MAXIMUM DRILLING DEPTH DISPLAY as a measuring function for the current drilling depth

Condition: new, Year of construction: 2024, machine/vehicle number: MR005970, Perfect cutting 200mm high! In double miter and with a fixed zero point. When the machine is mitered, the saw blade continues to enter the material at the same point. Technical specifications: - Fixed zero point: Yes - Miter angle: 45-90-25 ° - Tiltable: Yes - Tilt angle: 60-90-30 ° - Maximum cutting length: 420 mm - Maximum cutting height: 200 mm - Maximum saw blade diameter: 520 mm - Weight: 310 kg - Saw blade speed: 2800 /min - Motor power: 7 hp Hjdpovzl Scjfx Ag Eofn - Serial number: 2024/95/5

Condition: excellent (used), Year of construction: 1989, functionality: fully functional, Weiler Praktikant 140 B Lead and Feed Screw Lathe with Toolroom Accuracy featuring NEW K&C 3-Axis Digital Readout! Technical Data: - Year of construction: 1989 Machine No.: 89-140-1471 - Centre height: 140 mm - Centre distance: 650 mm - Spindle speeds: from 24 to 2500 rpm - Spindle bore: 40 mm - Short taper spindle nose DIN 55027 size 5 with bayonet lock - Tailstock MK 3 - Feeds: from 0.02 to 0.63 mm/rev - Thread cutting: Metric, Imperial (inch), Module and Diametral Pitch threads possible - Metric thread pitches: from 0.25 to 8 mm Hfsdpfjymdymsx Ag Ejn - Weight: approx. 680 kg - Spindle brake, selectable - Dimensions: Length 1.6 m, Height 1.25 m, Depth 0.7 m Accessories and Equipment: - NEW K&C 3-axis digital readout, 12 months manufacturer warranty and operating manual Functions: switch mm/inch, coordinate selection ABS/INC, display value halving, reference point, tool library for 200 tools, taper calculation, radius/diameter indication, quick zeroing, count direction switching - NEW collet system with collets from 3 to 25 mm, 1 mm increments - Three-jaw chuck, 160 mm, with 1 set of jaws - Multifix size A with 2 tool holders - Face plate - Bed stop - Rear cover - Machine feet - Electronic spindle guard - Operating manual Safety features: Electronic spindle protection, lead and feed screw cover, 2 emergency stops, spindle brake, electronic change gear guard About the machine: For sale is a Weiler Praktikant 140 B lead and feed screw lathe in very good condition. This well-maintained lathe comes from a training workshop. All slides operate smoothly and evenly. Even at high spindle speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and allows the production of ground-like surface finishes. Take the opportunity to view and test this machine under power on site to verify its condition for yourself.

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, travel distance X-axis: 2,000 mm, travel distance Y-axis: 685 mm, travel distance Z-axis: 630 mm, controller model: Siemens 840D, rotational speed (max.): 20,000 rpm, The machine spindle was replaced in 2022! The original purchase price of the machine was EUR 600,000! TECHNICAL DETAILS Travel range X-axis: 2000 mm Travel range Y-axis: 685 mm Travel range Z-axis: 630 mm Rapid traverse on all axes: 40 m/min Axis acceleration: 0.25 g Max. spindle speed: 20,000 rpm Max. rotary table speed: 1,000 rpm Tool changer positions: 92 Tool holder: HSK 63 NC swiveling axis: ± 100° MACHINE DETAILS Control: Siemens 840D EQUIPMENT Remote diagnostics and teleservice Maintenance instructions displayed on screen 5-axis milling package Fixed table with integrated rotary table Kessler milling rotary table DTE 520 NC swiveling head with spindle stock Direct measuring systems Chip conveyor (hinged belt) Coolant system HL 450 / 900 (IKZ) Full-flow cleaning via paper band hydrostatic filter HL450 Coolant filtration 50 µm nominal Chip blow gun Coolant recooling unit Additional tray rinsing Machine preparation for air through spindle Work area extraction system Safety package MILL 2000 with reinforced cabin and safety glass Zero point clamping system NSL tur 570-5-Z for DTE 520 Tool breakage monitoring Measuring probe Renishaw OMP 40-2LS Rotating inspection window Hsdjymnykepfx Ag Eofn Chiron Power Service Siemens CNC control with OP019 19" color display Operating mode: 4 MCIS DNC for sending and receiving CNC programs in network operation Siemens tool life monitoring Measurement in JOG (zero point determination during setup in jog mode) Loading and unloading station for tools for main time parallel tool change on background magazine Additional window for background magazine Swiveling control panel for optimal visibility of the work area during setup Note: The two vices on the NC rotary table as well as the tool holders in the tool changer are not included in the offer.

Condition: excellent (used), Year of construction: 2011, operating hours: 5,680 h, functionality: fully functional, Control system: WINMAX V08 Table dimensions: 1220 x 610 mm / D600 mm Table load capacity: 1000 kg X-axis travel: 1060 mm Y-axis travel: 610 mm Z-axis travel: 610 mm C-axis: 0 - 360 degrees A-axis: +/-92 degrees Spindle speed: 12000 rpm Spindle taper: SK40 Drive power: 11/18 kW Hfjdpfx Ajy Ux Tfjg Esn Weight: 7500 kg Dimensions (LxWxH): 3200 x 2450 x 2650 mm Accessories / Features - NC rotary table - Swivel spindle - CTS 20 bar (Coolant Thru Spindle) - Chip conveyor - Coolant system - RENISHAW zero-point measuring system with touch probe - Machine feet - Manuals The machine is in very good technical condition. Immediately available.

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, machine/vehicle number: AS0456, SPINNER TTS-Duplex High-Performance Precision Turning Machine with multiple slide systems for simultaneous machining with several turrets in parallel with TWO turrets, positioned in the upper right and lower left of the working area Slide System 1, upper right with travel in X1 = 180 mm Y1 = 90 mm (+/- 45mm) Z1 = 704 mm Slide System 2, lower left with travel in X2 = 180 mm Z2 = 620 mm Tool holder on turret system BMT45 SPINDLE 1, version up to 5,000 rpm - 65mm Bar capacity 65mm SPINDLE 2, version up to 5,000 rpm - 65mm Bar capacity 65mm CNC CLAMPING FORCE ADJUSTMENT on Spindle 1 FOOT SWITCH CNC CLAMPING FORCE ADJUSTMENT on Spindle 2 SPINDLE COOLING, Spindle 2 FOOT SWITCH Control system SIEMENS 840DE with the following basic features: - SPINNER - SPIOS 24" Touch control panel for I4.0 applications - Control panel rotatable and tiltable for best ergonomics - incl. engraving cycles - 24" liquid crystal flat color display with multi-touch functionality - User memory 2 GByte - 15 zero point offsets - 1 free USB interface Hfodpfsy S Tlwex Ag Een - Ethernet interface standard SPINNER MULTI-CONTROL WHEEL on the control panel, integrating the following functions into a single control element: - Handwheel function in jog mode - Feed override in automatic mode - Start button and feed influence in single-block setup mode, automatically resetting to 0% at the end of the block -> all important functions of the setup mode integrated into one control element - SHOPTURN - 4-axis machining with a rotary axis - 3D SIMULATION of the finished part - REMNANT MATERIAL DETECTION - DXF reader - 4-axis turning/balanced cutting - "FORCE-CONTROL" - operation against a fixed stop - Rolling peeling - skiving of straight or helical internal and external gears Energy-saving function incl. automatic machine shutdown CHIP CONVEYOR as a hinged belt conveyor exiting to the right, incl. integrated coolant tank with a capacity of approx. 200l and a return pump at 100l/min at 0.9 bar. COOLANT SYSTEM as an additional tank, completely wired incl. accessories Capacity approx. 800l, incl. low-pressure pump 50l/min at 15bar, High-pressure pump 22l/min at 80bar Coolant nozzle in the working area EXHAUST DUST NOZZLE D=200mm DOOR AUTOMATION for the working area door UNIMAG interface for bar loader magazines WORKPIECE HOLDING DEVICE for holding workpieces WORKPIECE CONVEYOR STANDARD DOCUMENTATION in German consisting of machine manual and CNC manuals is delivered in digital form on the control system. STANDARD PAINTING in two colors, light gray RAL7035 and blue-gray RAL5008 Electrical version EUROPEAN STANDARD as follows: Operating voltage 3x400V +/-10% Mains frequency 50Hz (+/-2%) TN system (5-conductor) Tool holder package Notes: The price includes warranty services only within Germany. For new and demonstration machines, the pictures are not necessarily of the individual machine, but of comparable machines. Illustrated accessories such as clamping devices or tool holders are included in the scope of delivery only to the extent listed in the technical description. Please request a detailed offer ex works. Visit our factory near Munich or one of our showrooms. We may have other offers for comparable machines. Subject to prior sale.

Condition: good (used), Year of construction: 1999, functionality: fully functional, drilling capacity: 40 mm, quill stroke: 200 mm, quill diameter: 80 mm, Machine Specification • Work table 1800 x 600 mm with 4 T-slots • Traversing arm travel 1050 mm • Drilling spindle SK 40 with tool clamping device • Infinitely variable speed programming • Infinitely variable quill feed via three-phase servo motor • 2 T-slots, 18 mm, rear side of machine base • 2 T-slots, 18 mm, left side of machine base • Thread cutting unit • Central lubrication • Coolant system • Machine light Hsdpfx Aeyxw Ddsg Eefn • CE marking • Safety device • USB interface Dimensions and Travel Ranges Tool holder: SK 40 Column diameter: 195 mm Table dimensions: 1800 x 600 mm Number of T-slots: 4 Distance between T-slots: 125 mm Quill travel (Z-axis): 200 mm Column travel (W-axis): 410 mm Distance spindle nose – table (min): 70 mm Distance spindle nose – table (max): 680 mm Distance spindle nose – floor (min): 970 mm Distance spindle nose – floor (max): 1580 mm Drilling radius: 540 – 1590 mm Working table height: 900 mm Machining Capacities Drilling capacity (solid): St 60: ⌀ 40 mm GG 22: ⌀ 50 mm Tapping: St 60: M36 GG 22: M42 Main Spindle Drive AC motor, frequency controlled: 5.5 kW at 100% duty cycle Speed range: 15 – 2800 rpm Torque: max. 250 Nm Constant torque from 15 – 2000 rpm Feed Drives X-axis - AC servo motor: 0.25 kW Y-axis - AC servo motor: 0.25 kW Z-axis - AC servo motor: 4.50 kW W-axis - AC servo motor: 2.50 kW Rapid traverse (X/Y/Z): 7.5 / 7.5 / 5 m/min Rapid traverse (W): 3 m/min Infinitely variable feeds: 5 – 2000 mm/min Accuracy Positioning accuracy X, Y axis (over 1200 mm): ± 0.075 mm Electrical Data Operating voltage/frequency: 400 V / 50 Hz Control voltage: 24 V Hydraulic unit for clamping: 0.75 kW Total connected load: 13.0 kVA Weight (Danumeric 440, without packaging, with 1800 x 600 mm table): 2800 kg CNC Control Axes: 4 (X, Y, Z, W), expandable Processor: 32-bit CPU Display: TFT flat screen, backlit, easily readable from all sides, 215 x 160 mm Position indication: Cartesian or polar, absolute or incremental Measurement units: mm or inch or degrees Interpolation: 2 axes (X, Y) Technology Database: Tool management, tool suggestions based on machining operation, material-dependent cutting data suggestions Tool management: max. 500 tools Subprogram function: yes Machining Cycles Standard software options: Conversational programming, 38 reference point shifts, rotation and mirroring, teach-in for X, Y, Z, program restart with selectable entry functions Zero point determination: cycles for determining reference points by manual probing of the workpiece for: - Arbitrary clamped rectangular parts - Arbitrary clamped round parts - Centering of cast and flame-cut parts - Angle position detection for round parts by probing reference edges or surfaces Test graphics: Graphical display of drilling patterns

Condition: ready for operation (used), Year of construction: 2013, TECHNICAL DATA Brand: FANUC Model: ROBODRILL α-D21LiA5 Year: 2013 CNC: FANUC 31i-MODEL B5 Serial Number: P135 YH478 TABLE DIMENSIONS Table size: 850 x 410 mm Load capacity: 300 kg T-slot spacing: 125 mm Number/size of T-slots: 3 x 14 mm TRAVELS X-axis travel: 700 mm Y-axis travel: 400 mm Z-axis travel: 330 mm Distance from table to spindle nose: 150 to 480 mm FEEDS Rapid traverse X/Y/Z: 54 m/min Cutting feedrate: 1 to 30 m/min MOTORS Drive motor: 11 kW (1 min) / 3.7 kW continuous Feed motors X/Y/Z: α8/4,000is (2.9 kW) TURRET Taper: MAS BT 30 Drawbar type: MAS P30T-1 (45°) Column to spindle center distance: 400 mm PRECISION Positioning accuracy: 0.006 mm Repeatability: ±0.004 mm Tool magazine capacity: 21 Maximum tool length: 250 mm Tool change time: Approx. 1.8 s SPINDLE Spindle speed range: 100 to 10,000 rpm Spindle taper: 7/24 Taper No. 30 Internal cooling MACHINE DIMENSIONS Machine height: 2,236 ± 10 mm Floor space required: 2,115 x 2,040 mm Machine weight (including control section): Approx. 2,100 kg POWER SUPPLIES Hfodpfxey At Aqs Ag Eon Electrical supply: 11 kVa Compressed air requirement: 0.35 to 0.55 MPa (gauge pressure) (0.5 MPa recommended), 0.15 m3/min (150 l/min) (at atmospheric pressure) ACCESSORIES Original FANUC 4th axis rotary table DDR (new price €18,000) Zero point clamping system Schunk NSE plus 138-V1 mounted on rotary (new price €2,100) Two Schunk KONTEC KSM2 90-400 vices (new price €2,000 each)

Condition: excellent (used), Year of construction: 1992, functionality: fully functional, Weiler Matador VS-2 Lead and Feed Screw Lathe with 3-Axis Digital Readout by K&C - NEW - Special Light Grey Paint Finish!!! Technical Data: >> Machine no. 92-029 - Year of manufacture: 1992 >> Center height: 140 mm >> Center distance: 500 mm >> Spindle speed: 15 – 3550 rpm >> Spindle bore: 36 mm >> Short taper spindle nose DIN 55022-5 with bayonet lock >> Tailstock taper: MK 3 >> Feeds from 0.012 to 0.9 mm/rev >> Thread types: Metric, Imperial, Module, and Diametral Pitch >> Metric thread pitches from 0.25 to 12 mm >> Weight approx. 700 kg >> Length: 1.4 m, Height: 1.2 m, Depth: 0.55 m Accessories and Equipment: >> 3-axis digital readout by K&C, new, 12-month manufacturer's warranty, with operating manual Functions: Switching between mm/inch, ABS/INC coordinate selection, value halving, reference point, tool programming for up to 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 three-jaw chuck, 1 set of jaws Hedpfxoyylqho Ag Eofn >> 1 four-jaw chuck, 2 sets of jaws >> Electronic spindle protection >> Multifix size A with 2 tool holders >> Motor brake >> Bed stop About the machine: Offered here is a Weiler Matador VS-2 in very good condition. The machine is, of course, fully functional and has been newly painted in light grey. A very attractive machine. The 3-axis digital readout by K&C has been retrofitted. All scales are new and equipped with protective covers to shield them from dirt. The carriage runs smoothly and evenly. Take the opportunity to view this machine under power on site and see its condition for yourself.

Condition: like new (used), Year of construction: 2025, functionality: fully functional, FORSTNER nuSLIT longitudinal slitting and cut-to-length line, year 2025. The machine is in excellent condition and fully operational. It was used only at several exhibitions and in a demo center. The machine is designed for longitudinal slitting and sheet cutting operations. It is fully programmable, with automatic adjustment of the longitudinal slitting knives. Longitudinal slitting into 6 strips (5 pairs of knives) with the possibility to mount up to 7 pairs. Equipped with a modern F3 control system featuring a touchscreen interface, which allows easy programming of different lengths, widths, and quantities. The controller communicates with an electronic eye, automatically sets the zero point, and enables precise, clean perpendicular cuts. Integrated material-saving function – the machine stops, the slitting knives are raised, and the sheet is automatically fed into the shears. Comes with complete technical documentation. Specification: Model: FORSTNER nuSLIT 1250 Made in: Austria Year: 2025 Working width: 1250 mm Max. thickness: up to 1.0 mm Longitudinal slitting knives: 5 pairs Cutting: rotary shears Controller: F3 Other features: automatically adjustable longitudinal slitting knives Hfodoy Dfnnjpfx Ag Een If you have any further questions, we will be happy to assist you.

Condition: new, Year of construction: 2025, CASADEI PFS 520 - Planer-thicknesser machine with 520 mm planing width and motorized thickness table adjustment Stable steel cast iron construction Large, ribbed planer tables made of cast iron, annealed to prevent warping Smooth operation due to high self-weight Four feed speeds Motorized thickness table adjustment with two speeds and digital display Segmented pressure shoes in the infeed 4-knife cutterhead, precision-mounted Helically toothed steel feed roller for particularly even and gentle wood feed Take-off roller with rubber coating Large planer fence, adjustable 90°-45°, readable from the front Standard with auxiliary fence Powerful S6 industrial motor (P2) Tersa cutterhead Knife changes in seconds When the machine starts, the knives are automatically tensioned by centrifugal force - self-clamping The knife overhang adjusts automatically without adjustment or screwing Hjdpsbxz S Hofx Ag Ejfn The planer table is adjusted by a stable and precisely guided parallelogram system, ensuring that the distance between the table tips and the cutterhead remains the same in every adjustment position. The stable aluminum planer fence is anodized as standard, easily adjustable, and offers a generous support surface. The adjustable inclination from 90° to 45° is easily readable from the workstation. Standard with an auxiliary fence for safe planing, even of narrow workpieces. Fig. with optional equipment The connection point for the dust extraction is always in the same position, both for planing and thicknessing. This eliminates the need for additional dust extraction hoses or cumbersome repositioning and routing around the machine. Technical data Total length of planer tables 2300 mm Infeed table length 1180 mm Planing width 520 mm Dimensions of planer fence 1200 x 190 mm Swivel range of planer fence 90 - 45° Min./Max. planing height 3/250 mm Cutterhead diameter / number of knives 100 mm / 4 pcs. Feed speed 5/8/12/18 m/min. Speed 5000 rpm Motor power 400 V / 50 Hz / S6 Dust extraction port diameter 120 mm Weight 1020 kg Top machine Location: Bitburg - available immediately

Condition: new, empty load weight: 3,210 kg, maximum load weight: 8,690 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,000 mm, loading space width: 2,000 mm, suspension: other, tire size: 235 / 75 R 17,5, color: other, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Loading height: 590 mm, track-reinforced steel checkered plate floor, 2 x ramps (2,600 mm long x 950 mm wide), 10 lashing points (2 tons) on the outer frame, 8 lashing boxes (5 tons) in the corners, geared support winch with load and fast gear, at the front, 2 folding supports at the rear, chassis and body hot-dip galvanized, surcharge for support block for milling belt: 600 EUR, also available with mechanical ramps in stock!, -- printing errors, errors and changes excepted, sample images --, more details under: !, More Details: ! Hodsz Stqpopfx Ag Ejfn

Condition: new, empty load weight: 3,080 kg, maximum load weight: 11,320 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,480 mm, suspension: air, tire size: 205/65 R 17,5, color: other, gearing type: other, front tire size: 205/65 R 17,5, rear tire size: 205/65 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Loading height approx. 820 mm, vehicle interior width approx. 2,480 mm, front panel made of galvanized steel, 600 mm aluminum sideboards, foldable and removable, 3 central stake pockets for 80 x 80 mm stakes, removable stakes, 6 lashing eyes, outer frame with lashing points, reinforced transmission support with load and fast gear, contour marking and side impact protection, fenders and spray suppression at the rear, surcharge for front panel grid 1,600 mm high (perforated sheet metal), price: 1,400 euros, surcharge for aluminum ramps, load capacity per pair 9 tons and 2 x folding supports at the rear, price: 1,900 euros, -- subject to printing errors, errors and changes, sample images --, more data at: !, More details: ! Hfodsz Stmkspfx Ag Ejn

Condition: new, empty load weight: 2,980 kg, maximum load weight: 7,520 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 6,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245 / 70 R 17,5, wheelbase: 990 mm, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, each ramp is approximately 2,700 mm long x 560 mm wide, ramps with grating, loading height: 840 mm, 12 tie-down points, each with a capacity of 2.5 tons, 8 tie-down points, each with a capacity of 6 tons, steel sideboards, foldable and removable, wooden planks, 50 mm thick, loading area sloped at the rear, interior loading area width 2,480 mm, rear underride guard removable, front section for drive-through loading, vehicle with temporary registration, also available with a loading area length of 5,300 mm!!, -- subject to printing errors, errors and changes, sample images --, more data at: !, More Details: ! Hjdpfoz Str Tex Ag Ejfn

Condition: used, empty load weight: 7,480 kg, maximum load weight: 23,520 kg, overall weight: 31,000 kg, axle configuration: 3 axles, first registration: 05/2025, loading space length: 8,000 mm, suspension: air, tire size: 235/75R17,5 -/140J, color: other, gearing type: other, front tire size: 235/75R17,5 -/140J, rear tire size: 235/75R17,5 -/140J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Chassis: Hot-dip galvanized, 18 tie-down points, 12 ladder rack sockets, 2 ramps each 3,110 mm long x 760 mm wide, hydraulic, one-piece ramps, hydraulic ramp adjustment, loading height: 880 mm, incl. axle load indicators, -- subject to printing errors, mistakes and changes, sample images --, more data at: !, More Details: ! Hfsdpfx Agez Smb Ao Een