Used Upper Support for sale (15,748)

Condition: used, This listing is for the Watson Marlow 620 Du/R Peristaltic pump The unit is in full working condition and is ready for immediate use The 620DU is a process peristaltic pump (i.e. hose pump) designed for metering, dosing, and transfer of fluids. Because it is a peristaltic design, the fluid is contained entirely within the tubing, avoiding contact with internal moving parts (other than the tubing). It is suitable for remote control, automation, and integration into control systems (SCADA, factory logic, etc.). Wide control range & precision: The large turndown (2,650:1) gives flexibility to handle both very low and high flow rates with fine control. Remote / automation capabilities: Because it supports analog and digital interfaces, it’s well-suited for integrated systems. Pump protection & security: PIN locking helps avoid unintentional changes in process-critical applications. Low maintenance on non‑wetted parts: Since only the tubing contacts fluid, mechanical wear is mostly on the tubing, making part replacement simpler. Safe to run dry: Peristaltic pumps typically tolerate running dry without damage (unlike many positive displacement pumps). Reversible / ability to back‑flush: This is helpful when attempting to clear lines or avoid clogging. Limitations / Considerations Tubing wear / life: The hose or tubing is the consumable component. Chemical compatibility, pressure, and mechanical stress affect how often tubing needs replacement. Upper pressure / flow limit: While it handles decent pressure (~2 bar standard, possibly up to 4 bar variant), it’s not suited for very high-pressure pumping tasks. Enclosure limitations (non-“N” model): The standard 620DU is not fully sealed, so it may not be ideal for wet or harsh environments unless you use the “N” variant. Hnodpfx Aisxhdt Ietju Cost / complexity: More features, interfaces, and protection can make the system more complex (and costlier) to configure, install, and maintain.

Condition: used, axle configuration: 3 axles, first registration: 09/2025, loading space length: 13,535 mm, loading space width: 2,480 mm, loading space height: 2,825 mm, loading space volume: 92 m³, Chassis: Superstructure manufactured using a self-supporting design with corresponding reinforcements in the lower belt for particularly high stability and strength, cross members 140mm high – reinforced design (for high ground load), additional reinforcement as a gusset plate in the front lower belt/vehicle frame area, chassis made of galvanized steel up to the support structure (semi-trailer construction max. total weight up to 39,000 kg) Axles and Suspension: Disc brake 22.5 Jost (DCA) axle units – off-road, 3x9t with DCA air suspension, ECAS lifting and lowering valve, Wabco Smartboard, electronic brake wear indicator BVA – can be read in the central control unit, 1st axle liftable with starting assist, 3rd axle liftable with Optiturn and Optiload without central control unit equipment, Wabco Trailerpulse – tire pressure monitoring system Tires and Wheels: 6 wheels with tires of size: 385/65 R22.5, tires approx. 60-70% on steel rims silver in 11.75x22.5 ET 120 King Pin: 2" king pin screwed into a 10mm steel plate Landing Gears: Mechanical landing gears with two speeds, 2x 20t support load with pivoting foot Braking System: According to EG standard, EBS-E system Wabco with RSS system (Roll-Stability-Support) and premium modulator, spring brake system acting on two axles with operation in front of the first axle on the left, aluminum air reservoir system Electrical System: According to the guidelines of EG standard 91/633 and 97/28 with five-chamber lights type: Aspöck ECOLED 3, 24V system with 1x15-pole and 2x7-pole socket with side marker lights - LED flashing, 2x reflective panels on the rear, position lights at the front 2x white, rear 2x red, 2x reversing lights in the lamp carrier, audio alarm when reversing Superstructure/Body: Body inside fully welded, reinforced side walls, front wall load 17,250 dkN, side wall load 13,400 dkN, rear wall load 10,400 dkN, aluminum body, side walls 30mm thick aluminum side wall profiles (2-3mm) 600mm wide, completely welded with upper and lower belts reinforced, plank profiles inside fully welded, floor laid as a sliding floor system on 140mm cross members, floor load capacity approx. 9t/m?, cross members mounted closely together (approx. 350mm), aluminum front wall with 600mm plank profiles (2-3mm) in a straight design, special aluminum corner profiles in a beveled design, smooth rear wall in a straight design with 2 aluminum swing doors 30/50mm thick with 2 rotating rod locks in the welded aluminum rear frame, attached in Teflon and INOX bearings, doors secured in the open position with two fixed stainless steel door latches, hard wear plates on the side walls approx. 2,000x1,500x4 mm fully welded, moving residual emptying wall with Kevlar fabric approx. 1,800mm long, plus side Kevlar fabric seal, service door in the front wall on the left, opening inwards Hnodpfx Aiez S St Ajteu Hydraulic System "Cargo-Floor" Sliding Floor System: Sliding floor system in the floor with hydraulically moved aluminum profiles on aluminum square profiles with approx. 880 PE-HD slide bearings plus anti-lift slide bearings, floor type: CF 10mm ribbed, end plate aluminum, hydraulic cylinder with approx. 200mm working stroke, hydraulic connection between the support legs with a separate possibility for connecting the hydraulic line to the front wall, load compartments to be specified, line size NW 21, operating pressure 190-max 250bar, aluminum end pieces welded into the sliding floor, control console in front of the first axle on

Condition: good (used), mileage: 1,787 km, color: white, lifting height: 36,000 mm, General information Year of manufacture: 2017 Operating hours: 1.787 Drivetrain Drive: Wheel Make of engine: Honda Hodpfjz Stg Rjx Aitonu Weights Empty weight: 3.500 kg Functional Lifting capacity: 2.400 kg CE mark: yes Maintenance, history and condition Number of owners: 1 Technical condition: good Visual appearance: good Other information Front tyres / undercarriage remaining: 65 Rear tyres remaining : 65 Delivery terms: EXW Upper hours: 1787 h Production country: DE Additional information Please contact Michael Overmeer for more information = Additional options and accessories = - Hook blocks = Remarks = Böcker AHK 36/2400 trailer crane construction year 2017 with 1.787 hours from the first owner. Machine is in a nice condition and has among other things: a Honda petrol engine, automatic leveling, wheel drive operable from the remote, hydraulic support legs, hydraulic jib and radio remote control. Changes and typographical errors reserved.

Condition: used, Year of construction: 2016, Industrial automatic edge banding machine SOLUTION XD KEY FEATURES "E-TOUCH" CONTROL WITH AUTOMATIC PROGRAMMING: A SINGLE "TOUCH" IS ALL IT TAKES TO OPERATE THE MACHINE STANDARD PRESSURE DEVICE WITH DRIVE BELT FOR OPTIMAL PANEL GUIDANCE EDGE BANDING OF ROLL MATERIAL, STRIP EDGES AND SOLID WOOD EDGES GENERAL FEATURES Single-sided edge banding machine in left-hand version for edge banding of roll material and strip edges with all conventional hot melt adhesives. The base frame consists of a stable steel welded frame with higher rigidity, which provides optimal support for the installation of the processing units. The upper pressure beam consists of a thick-walled steel profile and a double trapezoidal drive belt, which is automatically positioned according to the panel thickness. Height adjustment with display on the upper pressure beam and on the operator panel. Manual workpiece feeding system with a large-sized work area and increased support surface facilitates the feeding of large workpieces. Adjustable infeed fence for two positions with automatic selection for processing with or without a pre-milling unit. Upper working units are attached to the pressure beam and mechanically connected to ensure automatic adjustment when changing panel thickness. Lower working units are attached to the machine frame or to the longitudinal support for precise referencing to the panel. All high-frequency motors are operated via frequency inverters. Each unit is equipped with its own inverter for optimal flexibility and improved machine production times. Protective hood for all units positioned after the glue application unit. Polycarbonate windows ensure a good view of the units during processing. Interior lighting of the hood. Protective hood with sound-absorbing material for lower noise emissions during operation. Spacer on the infeed fence allows the machine to be fed with the correct spacing. The spacing is automatically adjusted to the selected feed rate. Dust extraction port arranged on the pivoting control panel, positioned in the infeed area, is adjustable for ergonomic operation. The electrical system complies with current regulations. Electrical components are housed in a metal housing, attached to the machine frame and equipped with doors for easy access in case of maintenance. Standard voltage is 400 V EU 50 Hz (with neutral conductor). Material feed is via a feed chain with 80 mm wide chain plates made of rubberized nylon, for optimal guidance and high load capacity. The chain slides on 2 guides made of hardened and ground steel, one round and one flat guide, to guarantee straight feed and to protect against lateral displacement. Automatic chain lubrication. The amount of lubricating oil is optimized by the control system depending on the panels being processed. External support roller track positioned along the entire length of the machine; consisting of an extendable opening system up to 650 mm (for panels with a maximum width of 1200 mm). E-TOUCH PC control system for quick and easy execution of the main functions of the machine. Includes: – Processing of programs in Just in Time mode – Possibility of management via bills of materials – Possibility of management by Hjdpfxjxy Tm Is Aitsnu

Condition: excellent (used), Catalog number: 7715 TECHNICAL DATA - Max. width of workpiece: 220mm - Max. height of workpiece: 130mm - 8 spindles: 1) Horizontal, lower: 220mm, 5.5kW 2) Vertical, right: 130mm, 7.5kW 3) Vertical, left: 130mm, 7.5kW 4) Vertical, right: 130mm, 5.5kW 5) Horizontal, upper: 220mm, 11kW – 5th spindle adjustable electrically, up/down 6) Horizontal, lower: 220mm, 5.5kW 7) Horizontal, lower: 220mm, 5.5kW – 7th spindle with support + Jointer system (cutterhead sharpening) 8) Universal: 220mm, adjustable 360°, 7.5kW - All spindles adjustable, up/down, left/right Hnodpjzx Rlxofx Aitsu - Spindle diameter: 40mm – Top: - 6 infeed rollers, double-toothed, pull-type + 1 single - 3 outfeed rollers, pull-type, rubber, smooth, double + 3 single - Meter counter – Bottom: - 1 infeed roller, toothed, pull-type, swiveling in the lower table - 3 metal outfeed rollers, pull-type, smooth - Feed on Cardan shafts - Rollers with pneumatic pressure - Stepless feed speed adjustment + 2 speeds, 10-60m/min - Feed motor: 10kW - Electric adjustment of planing thickness - Body lifting motor: 0.75kW - Central lubrication of the table - Diameter of dust extraction nozzles: 5x140mm, 3x120mm - Machine dimensions (L/W/H): 4680x1780x1850mm - Control cabinet dimensions (on pallet): 1020x1000x2230mm - Weight: approximately 5000kg ADVANTAGES - 8 heads - Universal spindle - Ideal for both wet and dry wood - German production, WEINIG brand - Unpainted - Very few operating hours - Used planer, in perfect condition Net price: 125900 PLN Net price: 29280 EUR, depending on the exchange rate of 4.30 EUR (Prices may change due to higher fluctuations)

Condition: as good as new (ex-display), Code: N0506 Brand: FELDER - AUSTRIA Model: K 700 S – CE Standard Precision panel saw with tilting blade and scoring unit - CE Standard Technical data: Hnjdpfx Ajzqd Htsitsu Tilting guide system “Easy-Glide” “Power-Drive” for automatic adjustment of blade height and tilt Carriage length 3200 mm Blade inclination 90/45° Cutting width 1250 mm Max blade diameter315 mm Bore 30 Rpm 4800 Max cutting height at 90°104 mm Max cutting height at 45° 72,7 mm Adjustable scoring unit - blade diameter 120 mm – Bore 20 rpm 8600 Main blade motor 7,5 Hp Tilting guide on fence 0,45° Support roller on fence Dust extraction connection diameter 120 mm Upper blade dust extraction diameter 50 mm Overall dimensions of assembled machine mm 3400 x 3400 x 1050 h Weight kg 740

Condition: excellent (used), WEINIG HYDROMAT 22 AL four-sided planer - max. workpiece width 220mm - max. workpiece height 130mm - 8 spindles: 1) horizontal lower 220mm, 5.5kW 2) vertical right 130mm, 7.5kW 3) vertical left 130mm, 7.5kW 4) vertical right 130mm, 5.5kW 5) horizontal upper 220mm, 11kW – 5th spindle adjustable electrically up/down 6) horizontal lower 220mm, 5.5kW 7) horizontal lower 220mm, 5.5kW – 7th spindle with support + Jointer system (cutterhead sharpening) 8) universal 220mm, adjustable 360°, 7.5kW - all spindles adjustable up/down, left/right - spindle diameter 40mm - from above: - 6 infeed rollers, double-toothed, pulling + 1 single - 3 outfeed rollers, pulling, rubber, smooth double + 3 single - meter counter - from below: - infeed roller, toothed, pulling, pivoting in the lower bed - 3 metal rollers, pulling, smooth - feed on Cardan shafts - rollers with pneumatic pressure - stepless feed speed adjustment + 2 speeds 10-60m/min - feed motor 10kW Hjdozyl T Tspfx Aitenu - electric thickness setting - body lifting motor 0.75kW - central lubrication of the bed - diameter of dust extraction nozzles 5x140mm, 3x 120mm - machine dimensions L/W/H 4680x1780x1850mm - control cabinet dimensions (on pallet) 1020x1000x2230mm - weight approx. 5000kg - Feeder with centering device: - roller width 450mm - 1 toothed pulling roller at the inlet - 22 smooth pulling rollers - adjustable pressure from above - feeder length 9020mm - stepless speed adjustment 10-60m/min - motor 0.75kW - dimensions L/W/H 9020x790x1150mm Net price: 179900 PLN Net price: 41850 EUR, depending on the exchange rate of 4.30 EUR (Prices may change with higher fluctuations)

Year of construction: 2021, operating hours: 17,634 h, condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Lift Mast Mast type: Duplex mast Lift height: 5,495 mm Free-lift mast: Without center hydraulic cylinder Free lift: No Load Capacity and Forks Load capacity: 3,500 kg Fork length: 1,200 mm Hydraulically adjustable forks: Yes Side shifter: Yes Drive Drive type: LPG (liquefied petroleum gas) Diesel drive: No MACHINE DETAILS Machine data Manufacturer: Linde Type: H35T Year of manufacture: 2021 Operating hours: 17,634 h Self-weight: 5,516 kg UVV certificate valid until: Formerly a Linde full-service unit Facelift model Dimensions Overall length: 5,200 mm Overall width: 1,450 mm Overall height: 3,424 mm EQUIPMENT 3rd and 4th hydraulic valve Fork positioner with side shifter Full cabin Air conditioning Heater Windshield wiper Comfort seat with lumbar support Hnsdjz R Dqwjpfx Aiteu Seat heating LED work light, front LED work light, rear Road traffic lighting with turn signals Orange warning light Safety light, front Safety light, rear All dimensions are rounded values. No guarantee is given for typing or measurement errors. Collection conditions: Lateral loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. In the event of delayed collection, a storage fee of €20 per machine per day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 45

Condition: new, pressing force: 135 t, operating speed: 10 mm/s, reverse speed: 130 mm/s, table height: 940 mm, overall weight: 7,750 kg, MVD SERIES B - 3,100x135Tn SERIES B - 4 Axes Large press brake for achieving outstanding bends and flawless workpieces The body and upper beam are of steel construction, designed according to minimum and optimum strength criteria. Model: B135/3100 Bending force: 135 tons Bending length: 3100 mm Distance between uprights: 2600 mm Ram stroke: 260 mm Daylight: 465 mm Throat depth: 410 mm Table height: 940 mm Length x Width x Height: 4690 x 2340 x 2980 mm Approach speed: 210 mm/s Return speed: 130 mm/s Bending speed: 10 mm/s Oil tank capacity: 180L Main motor: 11 kW Weight: 7,750 kg Standard features: CNC 3 axes Y1, Y2, X 260 mm stroke, 410 mm throat depth ESA S630 CNC control unit ± 0.03 mm precision SERVO-driven, motorized rear gauge X = 750 mm Hjdpfjxfzpzsx Aitenu Promecam quick-release punch holder Sliding front sheet support arms Special narrow bottom table by MVD (European type) GIVI optical linear scales Standard punch tooling (H: 67, 850 R:08) Standard die tooling (60x60 mm, 4 Vee V=16-22-35-50 mm, 85°, H:60) LED lighting in RAM Optional features: Choice of X-axis backgauge options with 2-4-6-8 stops Wide bottom table for Multi Vee forming dies Anti-deflection crowning with original Wila wedges AKAS or DSP front laser safety systems Additional backgauge fingers Front laser safety

Condition: new, Year of construction: 2026, machine/vehicle number: P786, functionality: fully functional, power: 5.5 kW (7.48 HP), input voltage: 400 V, pressing force: 60 t, stroke length: 215 mm, operating speed: 280 mm/s, reverse speed: 170 mm/s, table length: 1,550 mm, throat depth: 255 mm, distance table to ram: 400 mm, clearance between the columns: 1,200 mm, oil tank capacity: 120 l, overall weight: 6,500 kg, Equipment: CE marking, documentation/manual, safety light barrier, Small, powerful all-rounder! Also suitable for multi-station operation! The High Quality Press Brake, or HQPB for short, is the top model in the Placke range of press brakes. The entire manufacturing process, from the hydraulic cylinder to the control cabinet construction, takes place in-house. By using state-of-the-art technology, combined with many years of experience in the field of forming technology, the HQPB series enables you to bend at the highest level. Even the standard basic model is a fully functional press brake. This combination of safety, reliability and efficiency, together with easy operation, allows us to meet the highest requirements and accuracies in the bending process. Press force: 600 kN (60 t) Working length: 1,550 mm Distance between uprights: 1,200 mm Installation height: 400 mm Overhang: 255 mm Ram stroke: 215 mm Hnsdoz Hnz Dopfx Aitou Lower bed height above floor: 947 mm Rapid traverse max.: 250 mm/s Pressing traverse max.: 9.8 mm/s Retract traverse max.: 170 mm/s Ram positioning accuracy: ± 0.01 mm Ram inclination: ± 10 mm (electrically limited to ± 5 mm) Motor power: 5.5 kW Hydraulic oil tank capacity: 120 l Operating voltage: 400 V / 3 Ph / 50 Hz Machine weight: approx. 7 t Description: > Machine body: Steel S 355 N Design based on FEM analysis Side stands with two pressure tubes Floor-standing 2-component structural paint RAL 7004 / 7016 > Hydraulics & upper beam Proportional valve control, electronically monitored cylinder synchronization Press beam stress-relieved annealed, Heidenhain scales Separate Y1/Y2 control, inclination monitoring > Tooling Top: WILA hydraulic, NSCL-II-HC, fully hardened Bottom: narrow table, single V (13 × 20) Reinforced lower bed, no mechanical deflection required > Support arms 2 aluminum support arms at the front, approx. 600 mm, with tilting stops Can be moved on ball bearing linear guide Height-adjustable for dies from 55 to 100 mm > Back gauge 2-axis X-axis 950 mm, 300 mm/s, ± 0.01 mm R-axis 200 mm, 150 mm/s, ± 0.01 mm Z-axis manual with quick clamp, 2 stop fingers > Control system: Delem DA 66S 24″ touchscreen on swivel arm 2D programming, 3D visualization DXF import, tandem operation > Safety CE-compliant, Pilz safety PLC TFS laser light curtain, moving with the ram Rear light curtain > Control technology Back gauge with AC servo technology Compensation for side stand deflection and temperature-related stand expansion Dynamic press force control, LED work area lighting including lighting behind the machine

Condition: used, Upper support, cross support, cross table, cross slide table Hnedpoct Aa Rjfx Aitou -Upper support comes from a Waldrich Coburg portal milling machine type: 12 D 3232-550 HL -Table surface: mm -Travel: x 350 mm/y 220 mm -Dimensions: 1380/1000/H800 mm -Weight: 800 kg

Condition: used, maximum load weight: 44,980 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, first registration: 09/2024, next inspection (TÜV): 09/2025, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Chassis, bent * Special steel frame made of high-strength fine-grain steels, electrically welded at the joints, well-dimensioned outer frame * 4-axle arrangement. Wheel protection above the axles with spray mist suppression * All steel parts sandblasted * Lateral impact protection made of anodized aluminum mounted * Increased point load of approx. 30,000 kg over approx. 4,000 mm * Special design in the bent area for maximum low-bed length in combination with AluLeg outrigger supports instead of telescopic outrigger winches, max. rear swivel radius of the tractor unit approx. 2,100 mm Special superstructure with rear beam extension * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding tarpaulin with plastic flaps * Rear beams extendable to approx. 4,200 mm * Three sliding beams per side with rubber cord relief * Additional center beam locking in the roof beam and parking position, by means of a pull cable and spring latch * Lifting roof mechanically adjustable, lifting height approx. 400 mm, can be operated on both sides or on one side, without opening the opposite side and the doors * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the beams * Front overhang on the front wall for operation under tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, bottom 450 mm pockets, above 4 rows of single pockets * Only 3 rows of insert slats in the upper bed. Spacing between slats evenly distributed Floor * Approx. 27 mm special water-resistant glued beech plywood, rough surface * Steel sheet in the wheel arch area * Forklift truck accessible according to DIN standard * Outer frame flush with the surface Brakes * WABCO compressed air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve) * Spring brake cylinders as parking brake * Wabco Smart Board with odometer and aggregate load indicator Axles Hnodpslthguofx Aitsu * 4 x 10,000 kg SAF/Sauer with drum brakes in low-loader design * Air suspension with lifting and lowering device, total stroke approx. 230 mm * Third and fourth axles as friction-jointed trailing axles with electric and mechanical lock Twin tires * 235/75 R 17.5, -16-ply, incl. E-wheel holder. without E-wheel Paint finish * Chassis in RAL 3002 red, solid color * Center beams, axles coated with KTL black * Corner beams in hot-dip galvanized design * Plastic parts black * Hot-dip galvanized parts unpainted * Rims in factory silver * Superstructure in RAL color, solid color Special equipment incl. * Air suspension in ECAS design, operated on the semi-trailer * Overwidth signs front and rear in zinc-plated, steplessly telescopic design with attached warning lights including socket for rotating beacons (small panels) * Sliding tarpaulin cover locking additionally from the outside * 4 beam adapters for special outer frame profile, to lock the center beams as desired * PVC sliding tarpaulin, color similar: RAL 9006 silver * Roof tarpaulin translucent, in overwidth and overheight design, flat hooks, tarpaulin folds, closures with pawl lock /OCS * Telescopic socket for rotating beacon including beacon on the rear left * Outer frame for machine transport with app

Condition: good (used), Code: 0480 Brand: CASADEI INDUSTRIA Model: K 60 PM - CE Standard Automatic edge bander with  upper hot-melt hybrid adhesive tank for EVA and polyurethane glue with trimming unit for panels, furniture, furnishings, kitchens, and various - Year 2024 - CE Standard Hnodpfx Ajz Ekv Isitsu Technical data: Min/max panel height 8–60 Edge thickness10 mm Min panel length 120 mm Min panel width 110 mm Panel feed speed 11 mt/min Panel support roller opening 500 mm Configuration: Infeed trimming unit : 2 diamond cutters diameter 60 mm 64 mm height - PLC-controlled work cycle - Adjustable material removal from 0 to 2 mm with digital display - HF motors, 200 Hz - 12000 rpm - 1,1 Kw each PLC-controlled logic operation - Full machine control - Electronic glue heating control - Automatic temperature standby Infrared lamp for preheating the panel after pre-milling Anti-adhesive liquid spray unit Glue tank - Tank capacity 2 kg - n° 7 electric heating elements Pressure rollers with digital position indicator Automatic edge feed Pneumatic shear for cutting rolls up to 3 mm Automatic front and rear trimming unit - Motor 0,27 Kw - 12000 rpm Tiltable trimming unit with Z4 cutters - Motor power 0,50 Kw - 12000 rpm Edge scraper unit: Widia blades - Digital displays Glue scraper unit: adjustable adhesive removal with Widia blades Brush unit - Motors 0,13 Kw - 3000 rpm - Brush diameter 120 mm Soundproof protective cabin Operating air pressure 6,5 bar Suction connection ports: n° 1 diameter 120 mm - n° 2 diameter 80 mm Overall dimensions mm 3200 x 1000 x 1450 h Weight kg 780

Condition: new, Year of construction: 2026, machine/vehicle number: PB16040, functionality: fully functional, power: 18 kW (24.47 HP), input voltage: 380 V, input current: 30 A, input frequency: 50 Hz, type of input current: three-phase, pressing force: 160 t, stroke length: 250 mm, operating speed: 10 mm/s, reverse speed: 150 mm/s, table width: 100 mm, table length: 4,000 mm, table height: 850 mm, throat depth: 400 mm, ram plate width: 1,900 mm, ram plate length: 4,000 mm, distance table to ram: 3,500 mm, clearance between the columns: 3,500 mm, oil tank capacity: 400 l, total length: 4,500 mm, total width: 2,000 mm, total height: 2,650 mm, overall weight: 12 kg, Equipment: CE marking, safety light barrier, High-end electro hydraulic servo system, upper slider controller by the full loop synchronization. Main servo motor guaranteed high efficiency, lower noise, energy saving. Mechanical compensation on crowning of worktable and deformation compensation on throat, ensuring bending strength and precision. Qualified accessories used to ensure press brake’s long-term stability running. Ball screw and linear guide adopted to ensure accurate and fast backgauge. Hnedpfjy U Hmgox Aiteu Movable front support helps with bending convenience. 2D and 3D multifunctional CNC system from Delem and Cybelec. Equipped with side guards and closed rear guards. 8+1 axis/6+1 axis control European technician service, installation, training No. Name Parameter Unit 1 Nominal force 1600 KN 2 Worktable length 4000 mm 3 Worktable height 850 mm 4 Distance between vertical 3500 mm 5 Stroke 250 mm 6 Equipping die height 500 mm 7 Throat depth 400 mm 8 Control axes 8+1 Axes Y1, Y2, X1, X2, R1, R2, Z1, Z2+V 9 Y axis working speed Quick down 160 mm/s Working 10 mm/s Return 150 mm/s 10 Y axis repeat position accuracy ±0.01 mm 11 Main servo motor Power 18 KW Brand INOVANCE Speed 1500r/min 12 Work piece Precision Straightness 0.3 mm/m Angle ±30’ /m 13 Back gauge X axis Stroke 600 mm Max. speed 200 mm/s Repeat position accuracy ±0.02 mm 14 Back gauge R axis Stroke 200 mm Max. speed 150 mm/s Repeat position accuracy ±0.05 mm 15 Dimension (Approximate) Length 4000 mm Width 1900 mm Height 2600 mm 16 Weight(Approximate) 10500 Kg No. Parts Name Brand Brand Location Remarks 1 Main servo motor INOVANCE China 2 Servo motor and drive INOVANCE China 3 Main Electrics Schneider France 4 Oil Cylinder HEYAN China TOP BRAND 5 Seal ring NOK Japan 6 Hydraulic valve & Filter Rexroth BOSCH Germany 7 Pump Hawe Germany 8 Controller DA69T Netherlands 9 Toolings Cnstamp 10 Ball screw Hiwin China Taiwan 11 Guide rail Hiwin China Taiwan 12 Grating ruler GIVI ITALY 13 Footswitch Enchi China 14 Stop finger with linear guide YES 15 Crowing table Motorized 16 Front laser protection LNTECH CE standard 17 Side and Back doors with limit switch Schneider CE standard

Condition: used, Year of construction: 2016, operating hours: 3,200 h, power: 232 kW (315.43 HP), next inspection (TÜV): 09/2024, Equipment: air conditioning, all wheel drive, cabin, front linkage, * Deutz-Fahr 9340 TTV * First registration: April 29, 2016 * Year of manufacture: 2016 * Operating hours: 3,184 h * Electrically adjustable and heated mirrors * Automatic climate control * LED work lights * 60 km/h top speed * Performance Steering ready with ''EASY-STEER'' function * Upper link CAT III for front hitch with automatic locking device * External operation for front hitch with 7-pole and 3-pole front socket * Load-Sensing with 210 l/min * Additional electric control unit at the rear with 2x double-acting valve connections * Suspended and braked front axle * ISOBUS preparation * i-Monitor 2 12'' screen with color camera * K80 ball hitch -----Internal vehicle number: 9251----Errors and prior sale excepted. WhatsApp support available! If you have any questions about the vehicle or would like more information, please feel free to contact us conveniently via WhatsApp. Hnjdpfx Aevht Hnoitju WhatsApp German, English -- WhatsApp German, English, Arabic

Condition: used, mileage: 417,840 km, power: 355 kW (482.67 HP), first registration: 06/2022, fuel type: diesel, axle configuration: 2 axles, color: white, gearing type: automatic, Equipment: air conditioning, electronic stability program (ESP), parking heater, soot filter, Model Year * Model Year: 2022 Transmission * TraXon automatic transmission, 12+2 gears Driver Assistance Systems * Electronic Braking System (EBS) * Adaptive Cruise Control (ACC) * Hill Start Assist Lights and Visibility * Daytime running lights Audio & Communication * Radio * Audio interface * Information and service system Exterior * Air suspension with leaf springs * Fifth wheel coupling * Low noise * Roof spoiler * Electrically adjustable exterior mirrors * Differential lock * Speed limiter * Tool box * Upper and lower bunk Safety * Electronic Stability Program (ESP) * Outside temperature display * Curb mirror * Wide-angle mirror Interior * Fabric seats * Tachograph * On-board computer * Sun visor * Cooler box Comfort * Automatic climate control * Stationary air conditioning system * Auxiliary heater * Comfort seats * Air-suspended driver's seat * Armrest for driver/passenger * Seat heating * Power steering * Lumbar support * Electric windows * Central locking Tire Size * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5, dual tires Other Dimensions and Weights * Fuel tank: 545 liters * Wheelbase: 3,800 mm Hedpfx Aoz Shphjitsnu ----Vehicle location: 04862 Mockrehna. Errors and omissions excepted.

Condition: used, mileage: 436,212 km, power: 355 kW (482.67 HP), first registration: 06/2022, fuel type: diesel, axle configuration: 2 axles, color: white, gearing type: automatic, Equipment: air conditioning, electronic stability program (ESP), parking heater, soot filter, Model Year * Model Year: 2022 Transmission * TraXon automatic transmission, 12+2 gears Driver Assistance Systems * Electronic Braking System (EBS) * Adaptive Cruise Control (ACC) * Hill Start Assist Lights and Visibility * Daytime running lights Audio & Communication * Radio * Audio interface * Information and service system Exterior * Air suspension with leaf springs * Fifth wheel coupling * Low noise * Roof spoiler * Electrically adjustable exterior mirrors * Differential lock * Speed limiter * Tool box * Upper and lower bunk Safety * Electronic Stability Program (ESP) * Outside temperature display * Curb mirror * Wide-angle mirror Interior * Fabric seats * Tachograph * On-board computer * Sun visor * Cooler box Comfort * Automatic climate control * Stationary air conditioning system * Auxiliary heater Hsdpfxez Shn Ro Aitonu * Comfort seats * Air-suspended driver's seat * Armrest for driver/passenger * Seat heating * Power steering * Lumbar support * Electric windows * Central locking Tire Size * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5, dual tires Other Dimensions and Weights * Fuel tank: 545 liters * Wheelbase: 3,800 mm ----Vehicle location: 04862 Mockrehna. Errors and omissions excepted.

Condition: used, mileage: 465,954 km, power: 355 kW (482.67 HP), first registration: 06/2022, fuel type: diesel, axle configuration: 2 axles, color: white, gearing type: automatic, Equipment: air conditioning, electronic stability program (ESP), parking heater, soot filter, Model Year * Model Year: 2022 Transmission * TraXon automatic transmission, 12+2 gears Driver Assistance Systems * Electronic Braking System (EBS) Hnjdpez Shpzofx Aiteu * Adaptive Cruise Control (ACC) * Hill Start Assist Lights and Visibility * Daytime running lights Audio & Communication * Radio * Audio interface * Information and service system Exterior * Air suspension with leaf springs * Fifth wheel coupling * Low noise * Roof spoiler * Electrically adjustable exterior mirrors * Differential lock * Speed limiter * Tool box * Upper and lower bunk Safety * Electronic Stability Program (ESP) * Outside temperature display * Curb mirror * Wide-angle mirror Interior * Fabric seats * Tachograph * On-board computer * Sun visor * Cooler box Comfort * Automatic climate control * Stationary air conditioning system * Auxiliary heater * Comfort seats * Air-suspended driver's seat * Armrest for driver/passenger * Seat heating * Power steering * Lumbar support * Electric windows * Central locking Tire Size * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5, dual tires Other Dimensions and Weights * Fuel tank: 545 liters * Wheelbase: 3,800 mm ----Vehicle location: 04862 Mockrehna. Errors and omissions excepted.

Condition: used, mileage: 510,071 km, power: 355 kW (482.67 HP), first registration: 06/2022, fuel type: diesel, axle configuration: 2 axles, color: white, gearing type: automatic, Equipment: air conditioning, electronic stability program (ESP), parking heater, soot filter, Model Year * Model Year: 2022 Transmission * TraXon automatic transmission, 12+2 gears Driver Assistance Systems * Electronic Braking System (EBS) * Adaptive Cruise Control (ACC) * Hill Start Assist Hnsdpfxoz Shp Ij Aiteu Lights and Visibility * Daytime running lights Audio & Communication * Radio * Audio interface * Information and service system Exterior * Air suspension with leaf springs * Fifth wheel coupling * Low noise * Roof spoiler * Electrically adjustable exterior mirrors * Differential lock * Speed limiter * Tool box * Upper and lower bunk Safety * Electronic Stability Program (ESP) * Outside temperature display * Curb mirror * Wide-angle mirror Interior * Fabric seats * Tachograph * On-board computer * Sun visor * Cooler box Comfort * Automatic climate control * Stationary air conditioning system * Auxiliary heater * Comfort seats * Air-suspended driver's seat * Armrest for driver/passenger * Seat heating * Power steering * Lumbar support * Electric windows * Central locking Tire Size * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5, dual tires Other Dimensions and Weights * Fuel tank: 545 liters * Wheelbase: 3,800 mm ----Vehicle location: 04862 Mockrehna. Errors and omissions excepted.

Condition: used, mileage: 470,010 km, power: 355 kW (482.67 HP), first registration: 06/2022, fuel type: diesel, axle configuration: 2 axles, color: white, gearing type: automatic, Equipment: air conditioning, electronic stability program (ESP), parking heater, soot filter, Model Year * Model Year: 2022 Transmission * TraXon automatic transmission, 12+2 gears Driver Assistance Systems * Electronic Braking System (EBS) * Adaptive Cruise Control (ACC) * Hill Start Assist Lights and Visibility Hnodpfx Ajz Shnwoitsu * Daytime running lights Audio & Communication * Radio * Audio interface * Information and service system Exterior * Air suspension with leaf springs * Fifth wheel coupling * Low noise * Roof spoiler * Electrically adjustable exterior mirrors * Differential lock * Speed limiter * Tool box * Upper and lower bunk Safety * Electronic Stability Program (ESP) * Outside temperature display * Curb mirror * Wide-angle mirror Interior * Fabric seats * Tachograph * On-board computer * Sun visor * Cooler box Comfort * Automatic climate control * Stationary air conditioning system * Auxiliary heater * Comfort seats * Air-suspended driver's seat * Armrest for driver/passenger * Seat heating * Power steering * Lumbar support * Electric windows * Central locking Tire Size * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5, dual tires Other Dimensions and Weights * Fuel tank: 545 liters * Wheelbase: 3,800 mm ----Vehicle location: 04862 Mockrehna. Errors and omissions excepted.

Condition: used, mileage: 463,935 km, power: 355 kW (482.67 HP), first registration: 06/2022, fuel type: diesel, axle configuration: 2 axles, color: white, gearing type: automatic, Equipment: air conditioning, electronic stability program (ESP), parking heater, soot filter, Model Year * Model Year: 2022 Transmission * TraXon automatic transmission, 12+2 gears Driver Assistance Systems * Electronic Braking System (EBS) * Adaptive Cruise Control (ACC) * Hill Start Assist Lights and Visibility * Daytime running lights Audio & Communication * Radio * Audio interface * Information and service system Exterior * Air suspension with leaf springs * Fifth wheel coupling * Low noise * Roof spoiler * Electrically adjustable exterior mirrors * Differential lock * Speed limiter * Tool box Hnsdpfxoz Shnqj Aitsu * Upper and lower bunk Safety * Electronic Stability Program (ESP) * Outside temperature display * Curb mirror * Wide-angle mirror Interior * Fabric seats * Tachograph * On-board computer * Sun visor * Cool box Comfort * Automatic climate control * Auxiliary air conditioning * Auxiliary heater * Comfort seats * Air-suspended driver's seat * Armrest for driver/passenger * Seat heating * Power steering * Lumbar support * Power windows * Central locking Tire Dimensions * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5, dual tires Other Dimensions and Weights * Fuel tank: 545 liters * Wheelbase: 3,800 mm ----Vehicle location: 04862 Mockrehna. Errors and omissions excepted.

Condition: used, mileage: 534,225 km, power: 355 kW (482.67 HP), first registration: 06/2022, fuel type: diesel, axle configuration: 2 axles, color: white, gearing type: automatic, Equipment: air conditioning, electronic stability program (ESP), parking heater, soot filter, Model year * Model year: 2022 Transmission * TraXon automatic transmission, 12+2 gears Driver Assistance Systems * Electronic Braking System (EBS) * Adaptive Cruise Control (ACC) * Hill Start Assist Lights and Visibility * Daytime running lights Audio & Communication Hjdpfxoz Shpus Aitenu * Radio * Audio interface * Information and service system Exterior * Air suspension with leaf springs * Fifth wheel coupling * Low noise * Roof spoiler * Electrically adjustable exterior mirrors * Differential lock * Speed limiter * Tool box * Upper and lower bunk Safety * Electronic Stability Program (ESP) * Outside temperature display * Curb mirrors * Wide-angle mirrors Interior * Fabric seats * Digital tachograph * On-board computer * Sun visor * Cool box Comfort * Automatic climate control * Parking air conditioning * Parking heater * Comfort seats * Air-suspended driver's seat * Armrest for driver/passenger * Seat heating * Power steering * Lumbar support * Electric windows * Central locking Tire Dimensions * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5, dual tires Other Dimensions and Weights * Fuel tank: 545 liters * Wheelbase: 3,800 mm ----Vehicle location: 01471 Radeburg. Errors and omissions excepted.

Condition: used, mileage: 459,568 km, power: 355 kW (482.67 HP), first registration: 06/2022, fuel type: diesel, axle configuration: 2 axles, color: white, gearing type: automatic, Equipment: air conditioning, electronic stability program (ESP), parking heater, soot filter, Model Year Hsdpfx Aiez Shpnotsnu * Model Year: 2022 Transmission * TraXon automatic transmission, 12+2 gears Driver Assistance Systems * Electronic Braking System (EBS) * Adaptive Cruise Control (ACC) * Hill Start Assist Lights and Visibility * Daytime running lights Audio & Communication * Radio * Audio interface * Information and service system Exterior * Air suspension with leaf springs * Fifth wheel coupling * Low noise * Roof spoiler * Electrically adjustable exterior mirrors * Differential lock * Speed limiter * Tool box * Upper and lower bunk Safety * Electronic Stability Program (ESP) * Outside temperature display * Curb mirror * Wide-angle mirror Interior * Fabric seats * Tachograph * On-board computer * Sun visor * Cooler box Comfort * Automatic climate control * Stationary air conditioning system * Auxiliary heater * Comfort seats * Air-suspended driver's seat * Armrest for driver/passenger * Seat heating * Power steering * Lumbar support * Electric windows * Central locking Tire Size * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5, dual tires Other Dimensions and Weights * Fuel tank: 545 liters * Wheelbase: 3,800 mm ----Vehicle location: 04862 Mockrehna. Errors and omissions excepted.

Condition: good (used), Upper support, upper slide, dovetail guide, tool slide, cross table, support slide, support carrier Hnedpfxswcwndo Aiteu -Tool carriage: support carriage support carrier -Tool holder: Ø 32 mm -Dimensions: see photos -Dimensions: 460/190/H205 mm -Weight: 21.6 kg

Condition: used, mileage: 449,302 km, power: 355 kW (482.67 HP), first registration: 04/2022, fuel type: diesel, overall weight: 20,500 kg, axle configuration: 2 axles, color: white, gearing type: automatic, Equipment: air conditioning, electronic stability program (ESP), parking heater, soot filter, Model Year * Model Year: 2022 Transmission * TraXon automatic transmission, 12+2 gears Driver Assistance Systems * Electronic Braking System (EBS) * Adaptive Cruise Control (ACC) * Hill Start Assist Lights and Visibility * Daytime running lights Audio & Communication * Radio * Audio interface * Information and service system Exterior * Air suspension * Fifth wheel coupling * Low noise * Roof spoiler * Electrically adjustable exterior mirrors * Differential lock Hnodpsz Shn Defx Aitju * Speed limiter * Tool box * Upper and lower bunk Safety * Electronic Stability Program (ESP) * Outside temperature display * Curb mirror * Wide-angle mirror Interior * Fabric seats * Tachograph * On-board computer * Sun visor * Cooler box Comfort * Automatic climate control * Auxiliary air conditioning * Auxiliary heater * Comfort seats * Air-suspended driver's seat * Armrest for driver/passenger * Seat heating * Power steering * Lumbar support * Electric windows * Central locking Tire Size * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5, dual tires Other Dimensions and Weights * Payload: 12,920 kg * Permissible total weight: 20,500 kg * Fuel tank: 545 l * Wheelbase: 3,800 mm ----Vehicle location: 04862 Mockrehna. New service was performed on 07/26; all data is available in the online history. Errors and changes excepted.