Used Tube Vise Pioneer for sale (2,612)

Condition: new, Cesurbend Mandrel Bending Machine / Tube Bending Machine PBH-32 Technical specifications Max. tube diameter: 32 mm Max. wall thickness (mm): 2 Max. bending angle (°): 190 Tube bending speed (d/min): 8.5 Nledpfxsxt Rb Ns Ahkof Max. bending radius (mm): 275 Bending motor power (kW): 2.2 Hydraulic motor power (kW): 1.5 Tube length (mm): 2000 Machine width (mm): 1000 Machine length (mm): 2300 Machine height (mm): 1050 Machine weight (kg): 400 Features • Hydraulic clamping • Brake motor / precision rotation • Manual size adjustment

Condition: new, Cesurbend Mandrel Tube Bending Machine / Pipe Bending Machine PBNC-51 Technical Specifications Max. Tube Diameter: 51 mm Max. Tube Wall Thickness (mm): 3 Max. Bending Angle (°): 190 Tube Bending Rate (rpm): 7-10 Max. Hydraulic Pressure (bar): 200 Max. Bending Radius (mm): 250 Tube Length (mm): 3000 Bending Motor Power (kW): 5.5 Hydraulic Motor Power (kW): 3 Machine Width (mm): 1400 Machine Length (mm): 4215 Machine Height (mm): 1450 Machine Weight (kg): 1600 Features • In this process, the jaw clamps the tube after it is inserted into the machine. The tube is bent over the die to half its diameter. When using a mandrel and wiper, better results are achieved for bends requiring higher quality, with thinner wall thickness and smaller radii. • This is a three-piston machine with a hydraulic spool located behind the hydraulic boom. Nsdpfx Asxt Rc Tehkolf

Condition: used, MULTIHEAD TUBE CUTTING MACHINE MAIR TRA3000/7/8 Scope of supply: 1 Loading table with: - Motorised slings loader, to load the complete bundle - Lateral chain transport conveyor, to introduce the tube 1 by 1 - Top support with vertical adjustment (to avoid loading of 2 tubes when working with small diameters) - Length stop and tube loader Nlsdsymaw Uepfx Ahkjf 2 Cutting machine TRA3000 with: - 7 independent cutting heads - All cutting heads can be lifted independently - Linear guide with scale for positioning of the cutting heads - Centralised tube transport system with production cycle adjustment 3 Double collecting cradle RA3, with: - Independent cradles, to collect the cut tubes - Lateral separators between cradles, to adapt the cradle length to the tube length - Motorised endless slings for soft tube collection. Note: with the double craddle system, it is possible to make the bundling and strapping in collecting craddle nº1, while production continues, without machine stop. 4 Main electrical cabinet and operator control panel NOTE:  This machine has worked very few hours.  Mechanical condition is very good.  It only requires cleaning & repainting to be “as new” Max. input tube length: 8000 mm Bundle Loader: 3 Tn Max. loading capacity: 3000 Kg Round tubes (outer Ø): 12-60 mm Square tubes (HxW): 12x12-40x40 mm Rectangular tubes (HxW): 12x16-50x30 mm Thickness Min.-Max.: 0.8 - 3.0 mm (depending on yield) Cutting lengths: 330 - 7900 mm Max. straightness tolerance: 1 mm/m Number of cutting heads: 8 Motors power: 2.2 kW Cutting disc diameter: 300 mm

Condition: new, functionality: fully functional, jaw width: 20 mm, jaw height: 19 mm, Flat EDM vice Brand: Matchling Type: V2075 Length: 125 mm, Width: 100 mm, Height: 20 mm (without spindle) Material: stainless steel Jaw width: 20 mm Clamping range: up to 75 mm Jaw height: 19 mm Down-thrust feature Corrosion-resistant Nodoymdamopfx Ahkolf In wooden box

Condition: used, functionality: fully functional, jaw width: 16 mm, jaw height: 19 mm, Flat EDM vice, used Nodpfoymdiuox Ahkelf Brand: Matchling Type: V1650 Length: 100 mm, Width: 100 mm, Height: 16 mm (without spindle) Material: stainless steel Jaw width: 16 mm Clamping range: up to 48 mm Jaw height: 19 mm With downforce feature stainless in wooden case

Condition: good (used), Year of construction: 2002, received a new control unit in 2019 for €14,000 Nedpfx Ahsykl Rzjkslf max. bending diameter: 63.5 mm smallest bending radius: 32 mm motor: 30 kW

Condition: good (used), functionality: fully functional, Year of construction: 2009, Used tube bending machine from Jutec Type: 5000 Capacity: up to approx. 40 mm Mandrel length: 4500 mm Nodoyfmwxjpfx Ahkjlf CNC controlled Automatic head Manually rotatable head with hydraulic clamping Incl. 3 sets of tools Year of manufacture: 2009 Very little used

Condition: new, Year of construction: 2025, neu 2025 .00775 Nlsdpfx Asyui Tzohkof prompt, Zwischenverkauf v 949.81 € 1 150 mm 40 mm 33 kg Vice [felix] 2.0 150 Quick-action drill chuck B18 3-16 mm (accuracy 0.17 mm) Taper mandrel B18/MK IV Reducing sleeve MK III/MK II Reducing sleeve MK III/MK I

Condition: new, Year of construction: 2025, neu Nsdpfx Ahjyukbgjkslf 2025 00774 prompt, Zwischenverkauf v Deutschland 523.41 € 1 100 mm 32 mm 12 kg Vice [felix] 2.0 100 Quick-action drill chuck B18 3-16 mm (accuracy 0.17 mm) Taper mandrel B18/MK II Reducing sleeve MK II/MK I

Condition: like new (used), functionality: fully functional, Year of construction: 2026, operating hours: 8 h, machine/vehicle number: BD38NCCOMP, bending angle (max.): 190 °, overall weight: 900 kg, total length: 3,100 mm, total width: 950 mm, total height: 1,500 mm, power: 6 kW (8.16 HP), input voltage: 220 V, type of input current: AC, warranty duration: 12 months, Semi-Automatic Single-Head Hydraulic Pipe Bending Machine BD50NC2A Machine Model: BD38NCCOMP Machine Applications  Transportation Sector For locomotives, automobiles, and bicycles: exhaust manifolds, brake lines, fuel supply conduits, steering mechanisms, air - conditioning ducting systems, seating assemblies, balancing components, bumper structures, window frame assemblies, handlebar components, and frame structures.  Furniture Industry Indoor and outdoor seating and table sets, office furniture including desks and chairs, shelving units, bed frames and associated furniture pieces.  Leisure and Recreation Industry Fitness apparatus, infant strollers, utility carts, and amusement ride installations.  HVAC (Heating, Ventilation, and Air - Conditioning) and Appliance Industry Water heating units, electric heating appliances, gas - fired cooktops, refrigeration units, and air - conditioning equipment.  Heavy Industrial Sphere Piping networks for boilers, heat exchanger, power generation plants, chemical processing facilities, diesel engine manufacturing, and shipbuilding operations.  Diverse Other Industries Household consumer goods, rehabilitation - oriented medical devices, sanitary fixtures, the decoration and interior design sector, the construction industry, agricultural machinery and equipment, and the aviation manufacturing and maintenance industry. Specification Nlodpfx Ahoya An Nskof The largest applicable carbon steel pipe (bending radius ≥ 2d) Φ38×2.0mm (thickness Max. 2.0) The largest applicable stainless steel pipe (bending radius ≥ 2d) Φ38×1.5mm (thickness Max. 1.5) Maximum core length (*) 850mm Critical Parts and Functional Components Maximum bending radius (*) 320mm Maximum bend angle 190° The number of bends that can be set for each pipe fitting (*) 25 bends The number of pipe fitting files can be set 280 sets (extensible) Working speed bending speed Max.90°/s Machine tool bending angle ±0.1°

Condition: new, functionality: fully functional, Year of construction: 2026, control type: CNC control, degree of automation: semi-automatic, controller manufacturer: PFEIFER technology, laser type: fiber laser, laser power: 6,000 W, laser wavelength: 1,064 nm, pipe diameter (max.): 160 mm, pipe length (max.): 7,500 mm, table length: 6,500 mm, type of input current: three-phase, type of cooling: water, compressed air connection: 13 bar, overall weight: 5,500 kg, total length: 14,800 mm, total width: 2,900 mm, total height: 2,525 mm, warranty duration: 24 months, year of last overhaul: 2026, working range: 7,500 mm, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, fume extraction, safety light barrier, PFEIFER technology skyTUBE Pro 6500 X3 – Profile and Tube Laser Centre 6500 x 15–160 mm with bevel cutting up to 50° skytube-pro-6500 X3 Profile and Tube Laser | Fiber Laser Metal Cutting for fast material change with up to 6kW — the smart and efficient tube laser processing solution for your production! Designed for round tubes, square tubes, rectangular tubes, open profiles, and special profiles. This laser cutting machine delivers maximum productivity, especially during production changeovers. The task: fiber laser up to 6kW for a wide range of metalworking applications. Unmatched Laser Cutting Performance High axis speeds and accelerations, paired with a stable mechanical structure, provide excellent cutting performance and accuracy. The tube and profile laser processing machine for production — space-saving and simply smart! Innovative solutions 100% made in Saxony! Tubes and profiles from 15 x 15 to 160 x 160 mm 3D cutting with efficient fiber laser technology The semi-automatic 6-fold profile tube loading chain system enables fast job changeovers. With the optional bundle loader, you can work completely independently. Bevel Cutting A function that changes everything. With our machine’s ability to swivel its cutting head up to 50° on an additional fifth axis, we address one of the biggest challenges in modern profile machining. If the laser beam always strikes the tube perpendicular to the surface, the cut edge will be elliptical. Swiveling the tube laser’s cutting head, combined with the feed axis, enables true bevel cutting. With the skyTUBE Laser, you are always on the safe side! The skyTUBE Pro is a class 1 laser system — there is no risk of exposure to laser radiation or reflections during operation. For all our laser systems, safety and compliance with the highest standards and regulations are paramount. Technical Features: · Closed industrial housing, class 1 or optionally class 4 laser · Working area, tube cutting system/clamping system: uniform tubes 15 to 160 mm, rectangular tubes 15 x 15 – 110 mm · Working area on tube X 6500 Y ±100 Z 150 A ±360° U ±50° · Automatic material feeding: up to 6 x 160 mm profiles, 3500–7000 mm lengths Njdpfx Ahjyh A Nyjkelf · Automatic material unloading system for profile sections, design matched to profile lengths · Z drive system: ball screw axis system with PTI SVZ system · X/Y drive system: linear axis system with PTI AC-SERVO system · Productive cutting speed: up to 50 m/min depending on material and laser combination (1.4G) · Software resolution: up to 2500 DPI · Repeatability: ±0.03 mm · Maximum footprint (W x D x H): 11,600 mm x 2,830 mm x 2,100 mm + unloading system, depending on required profile cut length. With standard version and 4.5 m automatic unloading, the total length is approx. 14,800 mm.

Condition: new, 4 x Ceramic Jacketed Radiant Tubes 514736 4 x Ceramic Jacketed Radiant Tubes 514736 L = 1520 mm OD = 128 mm Find more items - new and used - in our shop! Nlsdpfx Aheghrmaskef International shipping costs on request!

Condition: new, Year of construction: 2025, laser hours: 20 h, laser power: 3,000 W, laser wavelength: 1,060 nm, sheet thickness steel (max.): 12 mm, sheet thickness aluminum (max.): 6 mm, overall weight: 3,600 kg, total length: 8,600 mm, total width: 1,400 mm, total height: 2,400 mm, working range: 6,100,230 mm, Equipment: cooling unit, ATTENTION: Demonstration machine – The K-series sets new standards in terms of price and performance. It is a space-saving alternative to conventional tube laser cutting machines and offers an unbeatable price. With a length of just over 8 meters, it fits into almost any workshop. The time required to process bar stock, such as round, rectangular, square tubes, and profiles, is reduced to a minimum. An automated or semi-automated loading system is also available. Nedpfxeh Igimj Ahkjlf

Condition: used, Year of construction: 1999, color: red, loading space volume: 5 m³, loading space width: 1,700 mm, loading space length: 4,500 mm, loading space height: 600 mm, mileage: 1,001 km, first registration: 01/1999, gearing type: other, driver cabin: other, Vehicle location: Bovenden, steel body, tailgate Body: City skip loader with a drive-over tailgate, approximately 5 m³ capacity. Year of manufacture unknown, as no identification plate is present. Internal container. ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to change, prior sale and errors! Njdpfxoy U N Nks Ahkelf

Condition: new, Year of construction: 2026, functionality: fully functional, ALMI pipe notcher AL2 for pipes with outer diameter Ø48.3 (1 1/2″) and Ø60.3 (2") mm Pipe notcher for pipes with outer diameter Ø48.3 (1 1/2″) and Ø60.3 (2") mm Easy to attach to the wall Ideal for double corner connections Wall thickness max. 3 mm steel, 2.5 mm VA, weight 15 kg Nledpfx Ahey T N Svokef

Condition: used, mileage: 858,100 km, power: 260 kW (353.50 HP), first registration: 11/2008, fuel type: diesel, number of seats: 50, gearing type: automatic, emission class: euro5, color: white, Equipment: ABS, air conditioning, electronic stability program (ESP), soot filter, In accordance with our "General Terms and Conditions," without any guarantee or warranty, we can offer you the following vehicle on a non-binding basis until completion, subject to errors, typographical errors, and prior sale: Mercedes Benz Citaro LE intercity bus with partial leather seats and seatbelts (Vehicle 305) Njdpjzfdk Iefx Ahkslf First registration: November 20, 2008 858,100 km Engine: 11,967 ccm 260 kW / 354 hp Euro 5 EEV Technical inspection and emissions test due Permissible total weight: 19,000 kg Unladen weight: 13,020 kg Payload: 5,980 kg Axle load front: 7,245 kg, rear: 11,500 kg Overall length: 13,057 mm, overall width: 2,550 mm, overall height: 3,400 mm 50+20 seats and standing places + wheelchair/stroller or 50+15+1 Seatbelts, armrests, leather headrests Ramp at the double door Single door at the front, double door at the rear Windshield with stone chips Air conditioning, auxiliary heating, ventilation Radio/CD LAWO Without cash register Emergency exit Electric mirrors + mirror heating Fire suppression system out of order; fire extinguisher needs to be reprogrammed; battery was disconnected Engine slightly oily Full air suspension Fully automatic transmission Tires 275/70R22.5, approximately 30% tread remaining in the front, approximately 30% in the rear Price: €6,500.00 (net) All information is provided without any guarantee or warranty. Our "General Terms and Conditions" apply. The place of jurisdiction for both parties for disputes up to a value of €10,000 is the Ludwigslust District Court; for disputes exceeding this value, it is the Schwerin Regional Court. Subject to errors, typographical errors, and prior sale.

Condition: used, Year of construction: 2005, table length: 6,000 mm, total length: 6,000 mm, input voltage: 400 V, Ercolina EB 45 with tooling for inch-sized pipes Inspection and demonstration possible by appointment. Nedsyr H A Iepfx Ahkslf

Condition: ready for operation (used), Year of construction: 2002, operating hours: 147,007 h, spindle speed (max.): 6,300 rpm, travel distance X-axis: 370 mm, travel distance Z-axis: 250 mm, spindle motor power: 10,700 W, bar diameter (max.): 36 mm, controller manufacturer: TRAUB, controller model: TX8i (64-bit), workpiece diameter (max.): 32 mm, number of slots in tool magazine: 22, number of axes: 10, This 10-axis TRAUB TNK 36 horizontal turning machine was manufactured in 2002. It features a main spindle speed of 6,300 rpm and a counter spindle speed of 6,300 rpm. The machine includes a maximum workpiece diameter of 32 mm and a coolant tank capacity of approximately 360 liters. If you are looking to get high-quality turning capabilities, consider the TRAUB TNK 36 machine we have for sale. Contact us for further details. • 14" flat screen • Additional V24 RS232 interface in the electrical cabinet • MDE interface in the electrical cabinet (machine status and parts counter) • Rigid tapping without compensation chuck • Polyform function for C-axis • Tool monitoring • Main spindle bore: 36 mm • Main spindle drive power: AC 6.7 / 10.7 kW • Main spindle C-axis • Motorized counter spindle • Counter spindle bore: 32 mm • Counter spindle speed: 6,300 rpm • Counter spindle Z-axis travel: 250 mm • Counter spindle Z-axis rapid traverse: 30 m/min • Counter spindle C-axis • Counter clamping pressure device • Workpiece ejector • Increased feed force • Hainbuch Axfix chuck • X2 travel: 50 mm • Y2 travel: ±20 mm • Z2 travel: 100 mm • X2 rapid traverse: 15 m/min • Y2 rapid traverse: 15 m/min • Z2 rapid traverse: 15 m/min • 12 driven tools (via central drive) • Driven tool speed: 6,000 rpm • Electronic gearbox • X3 travel: 370 mm • Z3 travel: 250 mm • X3 rapid traverse: 30–60 m/min • Z3 rapid traverse: 30 m/min • 5 driven tools • Tool holder diameter: 40 mm • Driven tool speed: 6,000 rpm • Increased feed force • X4 travel: 73 mm • Y4 travel: ±50 mm • X4 rapid traverse: 15 m/min • Y4 rapid traverse: 15 m/min • 5 driven tools • Tool holder diameter: 40 mm • Driven tool speed: 6,000 rpm • Left-hand workpiece conveyor • Pneumatic workpiece gripper Nsdpfxozl S Eme Ahkslf • Gripper jaws: Ø5–8 mm / Ø8–20 mm / Ø20–36 mm • Maximum workpiece length: 200 mm • Maximum workpiece diameter: 32 mm • RESY compact belt filter • Cooling unit • Coolant tank capacity: approx. 360 l • Coolant pressure: 7 bar • Coolant flow rate: 50 l/min • Through-tool coolant: 30 bar • Coolant gun • Connected load: 22 kW Optional equipment, not included: • KNOLL 240S-1/100 hinged belt chip conveyor (discharge height: 950 mm) • Bar feeder preparation (guide tubes Ø25 / Ø36) • Rotating workpiece stop (16 × 16 mm shank) • Brankamp CMS 100 collision monitoring (main and counter spindle) • FMB Turbo 5-42 XT / 3200 "C" bar feeder • Basic set of static and driven tool holders included Technical Specification Through-spindle Coolant Yes Counter Spindle Yes Driven Tools Yes

Condition: used, functionality: fully functional, Year of construction: 2016, Combined profile and tube bending machine Manufacturer: Italy For round tubes up to 48 mm 1st station for ring bending for large radii 2nd station for tube bending up to max. 180 degrees Electrically driven Motor: 1.1 kW, 400 V, 50 Hz, 3-phase With digital display With foot pedal With tooling for 42.4 mm tube, radius approx. 150 mm Nledpfey Ryfnjx Ahkjf Weight approx. 350 kg

Condition: good (used), Machine vice, sturdy vice, drill press vice Nlsdpfjzlc Ncex Ahksf -Machine vice: Clamping jaws 125 x 34 mm -Clamping depth: 98 mm -Dimensions: 365/125/H70 mm -Weight: 15.7 kg

Condition: good (used), Code: 0445 Brand: LANDONI - ITALY Model: AGM 1 - CE Standard Portable electric sawig machine for heading and dividing of packed boards and logs - CE Standard Njdpfezl Dn Hox Ahkslf This pack cutter is also suitable for the cutting of rolls of paper with the specific Widia chain, and for the cutting of plastic blocks or tubes Technical data: Straight-tooth chain DLC-type with pitch 1" Chain tensioner for automatic chain tensioning Guide bar lenght cm 240 Useful cutting cm 200 Electric motor Hp 12,5 three-phase Automatic oiling of the chain Overall dimensions: mm 1800 x 900 x 3000 h Dimensions for transport: mm 3900 x 900 x 1900 h Weight kg 300

Condition: excellent (used), functionality: fully functional, Universal milling machine Deckel FP1 with 3-axis active digital display TNC 113 Heidenhain and stepless feed, in very good condition. Accessories, CE compliant. Technical data: >> Year of manufacture 1992, machine no. 2102-7007 >> Fixed angular table >> Speed: 40 - 2000 rpm >> Stepless feed in 3 axes >> Rapid traverse in 3 axes >> Drive power: 1.5 / 1.9 kW >> Spindle brake >> Travels X/Y/Z: 300/160/340 mm Nsdpfozl Ebbex Ahkslf >> Vertical milling head, adjustable on spindle head by 100 mm >> Vertical and horizontal quill - SK40 >> Clamping system M16 >> Weight approx. 800 kg Accessories and equipment: >> 3-axis digital display Heidenhain TNC113 >> Coolant system >> Machine lamp >> Operating manual, parts list >> Tool holders, vise, counter holder About the machine: Offered is a Deckel FP1 universal milling machine in very good condition and CE compliant. The machine has very little backlash and all spindles move easily. Even at maximum speeds, the milling machine runs very smoothly. A special feature is that the control cabinet is connected to the machine with a plug. This makes it easier to transport the machine. In this newer FP1 model, the feed is steplessly adjustable in three axes, and the machine also has rapid traverse in these axes. A major advantage is the active 3-axis digital display. With this Heidenhain positioning control, you can enter dimensions that the machine will automatically move to. The FP1 was used in a training workshop, where it was only used occasionally. An oil change was performed. Mechanically and electrically tested. The digital display from Heidenhain makes working easier and even more precise. Take advantage of the opportunity to inspect and test this machine on site under power.

Condition: used, Year of construction: 2016, machine/vehicle number: 0605-260018, FICEP Flex FRC 1201 Notching Machine The Ficep FRC 1201 notching machine is part of the modern Ficep Flex series of notching machines. This modern CNC-controlled notching machine is designed for the rapid thermal cutting and notching of H, U, L, flat, and square tubes. The steel profile is positioned in the machine at the cutting location via a roller conveyor using a pulling tong carriage. A robotic arm equipped with the cutting units (oxy-fuel or plasma) cuts the profiles at the selected position. The cut or notched finished components either fall into the collection tray or are pushed out of the system by the measuring arm. Thermal Cutting Units: This Ficep Flex FRC 1201 profile notching system is equipped for thermal cutting using oxy-fuel and/or plasma. A Hypertherm HYPERFORMANCE PLASMA HPR 260 XD plasma power source, suitable for material thicknesses up to 32 mm, is used. Thicker materials or phase cuts larger than 32 mm are cut using the oxy-fuel cutting unit. Conveyor System: On the infeed side, in front of the Ficep Flex FRC notching system, there is a chain-driven cross conveyor with a length of 11,150 mm. The profiles (components) can be conveyed in both directions. Nlsdpfx Aozmbgvohksf The profiles are then transported into the machine on a sturdy roller conveyor using a clamp-type measuring cart. The system is designed for 12-meter-long profiles and therefore features 12-meter-long roller conveyors on both the inlet and outlet sides, each with a roller track width of 1,300 mm. To remove the finished components on the outlet side, four chain-driven cross conveyors, each 6,450 mm long, are located downstream of the notching station. Mitrol CNC Control and Pegaso Software: The system is controlled by a modern CNC control system from Mitrol. This reliable CNC control system, manufactured by Ficep’s in-house supplier Mitrol, features Pegaso software, including remote maintenance capabilities and a data transfer interface. Torit DCE Filter Unit The filter unit for dust extraction is a Donaldson Torit DCE. Safety: via fence and light barriers Max. profile cross-section: 1,220 x 600 mm Min. material length: 2,500 mm Working height: 865 mm Weight: 7,000 kg Weight of cutting unit cover: 1,200 kg This modern Ficep Flex FRC 1201 notching machine is in very good condition.

Condition: excellent (used), functionality: fully functional, GAIANI PROFILE BENDING MACHINE DIAMETER 40 Nedpfx Aoznm Hkehkolf 3 ROLLERS HORIZONTAL USED, FUNCTIONAL MACHINE INTERNAL CODE: SVR 370

Condition: like new (used), functionality: fully functional, Year of construction: 2022, operating hours: 296 h, control type: CNC control, The Jinan Bodor P3T series is one of the manufacturer's most sought-after, fully enclosed industrial workhorses equipped with an automatic pallet changer. In addition to sheet metal processing, this machine is also designed for the precision cutting of tubes and profiles (T-version), allowing the entire production range to be covered with a single system.Dual Function: Flatbed sheet metal cutting and automatic tube cutting module in a single system. Maximum Safety: Fully enclosed protective cabin with laser safety glass for the complete protection of operators and the environment.Minimal Downtime: Automatic pallet changer system that enables loading and unloading during the cutting process.Outstanding Dynamics: High positioning speed and acceleration for maximum productivity.Intelligent Control: Bodor PRO. Technical Specifications: - Laser Source Power: 3000 W (3 kW) - Sheet Dimensions (X x Y): 3000 mm x 1500 mm - Tube Length Capacity: 6000 mm (6U execution) - Chuckable Tube Diameter: Ø20 mm – Ø170 mm (and corresponding square and rectangular profiles) - Chuck System: Automatic pneumatic / electric self-centering chucks - Control Software: Bodor PROPositioning Njdpjznwu Sjfx Ahkslf - Accuracy: ±0.03 mm - Cuttable Materials and Guideline - Maximum Thicknesses (3 kW): Carbon Steel / Mild Steel: max. 20 mm Stainless Steel: max. 10 mm Aluminum: max. 10 mm Brass / Copper: max. 6 mm Accessories and Scope of Delivery: - Factory industrial water chiller unit - Automatic voltage regulator / stabilizer - Extraction and dust filtration system - Automatic nozzle cleaner - Complete documentation and software licenses Condition and Inspection: - The machine has been continuously maintained and has a service history fully supervised by a specialized technician. It is currently in live production and can be inspected and tested under operating conditions by prior appointment. Subject to prior sale. Under power in Hungary.