Used Swivel Bending Machine for sale (85,059)

Condition: excellent (used), Year of construction: 1986, plate thickness 5 mm Ledpsxzk I Sefx Affjta sheet width 40 mm

Condition: new, sheet width 1070 mm plate thickness 9.0 / 10,0 mm distance between columns 1070 mm diameter of upper rolls 190 mm pre-bending capacity 9,0 mm connected load 5,3 kW weight of the machine ca. 2,4 t dimensions of the machine ca. 2,7 x 0,92 x 1,2 mm - Electrically adjustable rear roller - Electrically adjustable lower roll (material clamping) - Digital readout for rear roller movement - Digital readout for lower roll movement (material clamping) - Hardened rolls Ltedew In A Ijpfx Affsa - Conical rolling - Swiveling top roll - Brake motor - Emergency stop - Documentation - 400V

Condition: good (used), Year of construction: 1996, tube diameter 6 - 28 mm wall strength 2 mm bending radius min. 2 x D Control IPU 20 bending radius max. 5,0 x D mm bending angle max. 190 ° arbor length 3000 mm operating pressure 180 bar hydraulic motor 4 kW weight of the machine ca. 900 kg dimensions of the machine ca. 3,8 x 1,1 x 1,3 m Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut. Mandrel lubrication, adjustable length stops. Ledpfjvtgn Njx Affeta Operating modes: MANUAL and semi-automatic. Control buttons: hydraulics on / off, operating mode selection, clamp to / on, clamp forward / backward, mandrel forward / backward, bending forward / backward /, locking forward / backward, mandrel lubrication, turning device forward / backward, plate reset, length stop forward, emergency stop. The machine comes from a prototype construction and was only used a little until 2000. After that, the machines of this department were sold. However, the purchaser did not use the pipe bending machine and therefore it has only stood in the warehouse and has not worked since then ((original paint). Please notice that the price of a new machine today is over € 60.000,--. Machine dealer with own stock of 1600 m².

Condition: ready for operation (used), Year of construction: 1996, Tilting Spindle Moulder Table Moulder Woodworking Moulder Joiner’s Moulder CASOLIN Model: F45 Year of manufacture: 1996 5 adjustable spindle speeds: 3000/4500/6000/8000/10,000 rpm Table dimensions approx. 130 x 90 cm Milling fence with fine adjustment Electric height adjustment with digital display Electric tilting from -5° to +45° with digital angle display Spindle diameter: 30 mm Matching power feeders can be found in my other listings. Condition as shown in the pictures, please also refer to the item description. Parts may also be collected by the buyer. All dimensions are approximate. All information is provided to the best of our knowledge, but without guarantee. Subject to prior sale. Items can be collected in person or shipped at the buyer’s expense. Shipping costs are indicative and may vary depending on distance and unloading options. The listed sale price is a net amount plus VAT. An invoice with VAT shown will be provided. Lodpfxex Dmnaj Affjta Warranty terms: Due to wear and tear on used parts, items are generally sold as defective – for parts donors only – and only to businesses. By placing a bid, the buyer accepts this as the basis for the purchase agreement.

Condition: like new (used), Year of construction: 2011, STIERLI BIEGER 300 HE / As new, maximum 5 operating hours - Year of manufacture: 2011 - CE marking - Max. working pressure: 300 kN - Stroke length: 300 mm - Motor power: 4 kW - Hand switch Ltjdpfx Asx Dmduoffoa - Foot switch - Various dies - Bending tools - Back gauge - Documentation Dimensions: LxWxH 1.5x1.2x1.3 meters / Weight 850 kg Subject to errors and input mistakes.

Condition: good (used), Year of construction: 1998, GEOTECHNIKA XZ 1000/1 3-roll round bending machine Lodpoq Ix Anefx Affeta 1000mm year 1998 weight 200kg

Condition: reconditioned (used), functionality: fully functional, Year of construction: 2002, Mandrel bending machine for pipes up to 65 mm diameter Ltjdpfjx Dgwzex Affsa

Condition: new, sheet width 1070 mm plate thickness 4 mm distance between columns 1100 mm diameter of upper rolls 110 mm total power requirement 5,0 KW Ltodpfx Afovki E Sofsa weight of the machine ca. 1,2 t dimensions of the machine ca. 2,0 x 0,9 x 1,1 mm

Condition: new, The Hydraulic Tube Bender 1/2 is a compact and mobile Tube Bending Machine designed for bending steel tubes of larger diameters with a powerful manual hydraulic pump. This machine boasts a capacity of 10 tons and comes complete with dies for commonly used tube dimensions, allowing you to create bends of up to 90 degrees. With its robust 3-leg stand and 6 bending segments, it ensures stability and ease of use during operation. The included attachments cater to various diameters, making this versatile tool ideal for your tube and profile processing needs. You can efficiently bend tubes while enjoying the benefits of its portable design. If you require a reliable Tube Bending Machine, consider the Hydraulic Tube Bender 1/2 from KNUTH to enhance your workshop capabilities. Don't hesitate to request a quote today! Ltsdpfxeuzlh Is Affoa

Condition: used, Year of construction: 2023, Used machine Year of manufacture: 2023 Condition: as new, machine is unused Equipment and technical specifications: - Spindle speeds: 3,500 / 6,000 / 8,000 / 10,000 rpm - Milling spindle tilt: 0 to -45° - Usable spindle length: 125 mm - Spindle arbor diameter: 30 mm - Speed display: LED indicator on the machine front - Max. tool diameter (standard): 240 mm - Max. lowerable tool diameter: 230 mm - Max. tool diameter for profile milling: 240 mm - Max. tool diameter for tenoning: 320 mm - Working table length: 1,200 mm - Working table width: 530 mm Ljdjw E Tzropfx Affjta - Table height: 900 mm - Sliding table length: 1,200 mm - Sliding table width: 360 mm - Sliding table height: 142 mm - Extraction port diameter: 2 × 120 mm - Main drive motor power: 5.0 kW - Connection voltage: 400 V - Mains frequency: 50 Hz Dimensions: 1,200 × 2,000 mm Weight: 510 kg Availability: short-term Location: Saxony-Anhalt

Condition: used, Roller sets for section bending machine, 3-roll ring bending machine HERKULES WETZLAR The rollers fit a section bending machine HERKULES WETZLAR type BO 238 N Shaft diameter: 60 mm with 18 mm keyway 2 rollers set No. 1, roller diameter = 110 mm, roller width = 180 mm 2 rollers set No. 2, roller diameter = 160 mm, roller width = 40 mm Ltjdpfsglaq Iex Affsa 3 rollers set No. 3, roller diameter = 150 mm, for tube diameter Ø 33 mm, roller width 87 / 115 mm - Roller set No. 3 with adapter ring from Ø 93 to Ø 60 mm without keyway The machine had 2 driven rollers Total weight of all rollers: 57 kg Good condition

Condition: new, tube diameter 33,7 x 3,4 GAS mm tube diameter 35,0 x 2,5 STAHL mm tube diameter 35,0 x 1,5 EDELST mm bending radius min. R10 - R 190 mm bending angle max. 0 - 180 ° tool taper 6-kant 40 mm voltage 230 V total power requirement 0,9 kW weight of the machine ca. 23,0 kg Description: - MediBender "070" digital - with maximum bending performance for 35 x 2.5 mm steel tubes - Excellent bending quality with very tight bending radii . (from 2 x tube diameter) and bending angles between 0° and 180° - Easy to operate - High accuracy and reliability - Fast tool changes (within seconds) - Easy to transport - Huge selection of affordable standard tools (metric, gas inch, inch) Lodpsxab E Ssfx Affota BENDING SEGMENT AVAILABLE FOR AN ADDITIONAL CHARGE

Year of construction: 1980, condition: good (used), with initial rounding Technische Daten:/ technical details Biegelänge / bending lenght 2000 mm max. Blechstärke / max. sheet thickness 20 mm Anbiegeleistung / initial rounding 15/11 mm Walzendurchmesser Unterwalzen / roll diameter below rolls 280 mm Oberwalzendurchmesser / diameter of the upper roll 300 mm Antriebsleistung Hauptantrieb / drive capacity main drive 16,2 kW Antriebsleistung Anstellantrieb Oberwalze / drive capacity upper roll 4,8 kW Antriebsleistung Anstellsntrien Unterwalze / drive capacity below roll 3,7 kW Gewicht ca. / weight ca. 14200 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding. Ledpfxekzg E Aj Affota

Condition: new, sheet width 2070 mm plate thickness 4 mm Ltjdpfx Aefv H A Uoffsa distance between columns 2100 mm diameter of upper rolls 140 mm weight of the machine ca. 0,37 t

Condition: used, Year of construction: 2004, Technical details: tube diameter: 20 mm bending radius max.: 100 mm control for program: S7-300 tube pipe draw up length: 2270 mm air pressure - required: 7 bar total power requirement: 15 kW Bending speed: 540 °/sec control voltage: 24 V / DC V connection voltage: 400V / 50Hz / 3 Ph V dimensions L x W x H: Biegeaggregat: 1,8 x 1,4 x 1,6 m dimensions L x W x H: Zuführung: 1,2 x 1,5 x 1,55 m dimension machine xH: 3,0 x 1,0 x 1,2 m Ltjdpfeu Ibzkox Affoa Mandrel tube bending machine Bending direction RIGHT Operation via SIMANTIC Panel PC control unit Pneumatics: Pressure 7 bar; flow rate 200 l/min. Hydraulics: Pressure 150 bar; flow rate 6.8 l/min. Equipment/Accessories: -oil drip tray 3.1 x 0.96 x 0.02m -Spare parts and accessories *

Condition: used, Year of construction: 1987, Used machine Year of manufacture: 1987 Condition: fully overhauled Features and technical data: - Table size: 1100 x 760 mm - Motor: 4.7/5.7 kW, pole-switchable - With forward/reverse operation - Milling spindle: MK 5 / 30 mm - Height and tilt adjustment via handwheel - Spindle speeds: 3000/4500/6000/9000 rpm - Spindle tilt range: -5 to +45° - Milling fence with metal jaws - Mounted on round insert plate, therefore rotatable 360° Ljdpfxew I U U Ds Affeta - With table extension on both sides with retractable frame supports - Equipped with 4-roller power feed unit Weight: approx. 900 kg Images show the machine in unrefurbished condition Availability: approx. 4 weeks after order placement Location: Flörsheim

Condition: good (used), comac Series 3000, Model 303 Heavy-Duty Profile Bending Machine | 3 Driven Rolls The Series 3000 – Model 303 is a powerful and precise profile bending machine designed for demanding industrial bending applications. With its robust construction, three driven rolls, and modular roll system, this machine is suitable for a wide range of profiles, pipes, and tubes. Equipped with a solid 3 kW motor, individually adjustable bending rolls, a free-standing remote control, and both vertical and horizontal operating modes, the 303 offers maximum flexibility and ease of use. The machine complies with the 2006/42/EC Machinery Directive and is built for long-lasting, trouble-free performance. Key features - Compliant with 2006/42/EC safety standards - 3 driven rolls for maximum grip and perfect material feed - Independently adjustable bending rolls for double pre-bending of symmetrical profiles - Lateral guide rolls with three-dimensional adjustment - Modular rolls suitable for most standard profiles - Alloy steel bending rolls, heat treated to 60 HRC - Free-standing safety remote control - Suitable for vertical and horizontal installation - One-piece steel frame for extreme stability - Torque limiter on the upper shaft - Shafts and gears mounted on rolling bearings for high dynamic loads - Spline-driven power transmission for optimal force transfer Technical Specifications - Shaft diameter: 50 mm (upper/lower) - Roll diameter: 180 mm - Motor power: 3 kW - Feed speed: 5.5 m/min - Weight: 720 kg Bending Capacities Profile Up to Minimum bending radius 60 × 10 mm – Ø 450 mm 25 × 5 mm – Ø 200 mm 80 × 20 mm – Ø 400 mm 32 × 32 mm – Ø 400 mm Ø 40 – Ø 400 mm Ø 60.3 × 2.9 – Ø 800 mm Ø 20 × 1.5 – Ø 220 mm Ø 48.3 × 4 – Ø 500 mm 60 × 30 × 2.5 – – 50 × 3 – – 60 × 6 – Ø 600 mm 30 × 4 – Ø 350 mm 50 × 5 – Ø 500 mm 30 × 4 – Ø 350 mm 60 × 60 × 7 – Ø 600 mm 50 × 50 × 6 – Ø 600 mm Ljdpfex A Iviex Affsta 70 × 70 × 8 – Ø 700 mm 80 × 45 – Ø 500 mm 70 × 40 – Ø 600 mm 80 × 42 – Ø 500 mm

Condition: new, tube diameter 42.0 mm Stahl wall strength 3.0 mm Stahl tube diameter 54.0 mm CU/Alu bar material - diameter 30.0 mm wall strength 2.0 mm revolutions per minute 2.0 U/min voltage 230 Volt total power requirement 1.1 kW weight 80.0 kg Ljdpfx Afjxaa Sdofeta range L-W-H 410 x 1000 x 570 mm ERCOLINA MediBender "MB 42 M" - Capacity steel pipe 42 x 3.0mm - Capacity gas pipe 1“1/4 gas x 3.5 mm - Capacity square profile (FE 42) 35 x 35 x 3 mm - Max. bending radius 10-260 mm - Minimum radius 2 x D - 6-edge tool holder - Min. outside diameter 5 mm - 1/8“ gas Equipment: - patented fast tool change system - one bending speed - freely movable foot switch - bending tools on request for an additional charge including ERCOLINA microprocessor control: - with 30 programs each program with up to 9 bending angles programmable - in addition, the necessary correction angles can be entered . for each bending angle in the working mode BENDING SEGMENT AVAILABLE FOR AN ADDITIONAL CHARGE

Condition: good (used), functionality: fully functional, machine/vehicle number: 804, roller length: 2,550 mm, working width: 2,500 mm, sheet thickness (max.): 16 mm, sheet thickness steel (max.): 16 mm, overall weight: 12,500 kg, 3-roll hydraulic plate bending machine 2500 x 16 mm Manufacturer: KUMLA Type: PV 7 H Ltodpevxbm Rjfx Affoa Serial no.: 804, overhauled in 1987 The machine is of a very robust design and has only been used in single-shift operation. Max. bending length: 2500 mm Max. sheet thickness: 16 mm Cone bending device Top roll diameter: 324 mm Bottom roll diameter: 305 mm Hydraulic roll adjustment Dimensions: L x W x H = 5000 x 1600 x H 1900 mm Working height: 1000 mm Additionally, a staircase platform around the machine can be purchased.

Condition: new, Year of construction: 2025, Sturdy cast iron steel construction Large dimensioned milling unit made of cast iron, swivels up to -45° backwards Indication of the milling speeds by LEDs Fast, trouble-free speed change via eccentric voltage Right-left rotation Display of height and inclination 1/10 mm accurate Milling fence in heavy professional design: with fine adjustment via toothed rack, with numerical display, aluminum stop jaws, 3-fold positionable for fast repetition of the adjustment TECHNICAL DATA Suction connection suction port diameter 2 x 120mm working table working table length 2500mm Working table width 655mm Electrical data Supply voltage 400V Mains frequency 50Hz Power drive motor 5,0kW Milling spindle spindle inclination 0 - -45 useful length of the spindle 125mm Spindeldrehzahl(en) 3500/6000/8000/10000min¯¹ spindle mandrel diameter 30mm Milling tool diameter max. tool diameter max. 240mm Lodpfxsiidnfe Affsta tool diameter max. lowerable 230mm tool diameter max. profile milling 210 - 240mm tool diameter max. tenon milling 320mm SUPPLY Aluminum milling stop jaws Arch milling protection hood Motorized height adjustable and swiveling milling spindle Digital display of the set values Speed display on the machine front via LED Table extension left and right Location: Ex stock 54634 Bitburg - immediately available -

Condition: used, Year of construction: 1992, Technical details: tube diameter: 6 mm Ltsdowivn Njpfx Affsa tube diameter max.: 16 mm bending angle max.: 90 ° electrics - voltage/frequency: 220 / 50 V/Hz Total power requirement: 0,75 kW Weight approx.: 0,145 t machine dimensions LxWxH: ca. 1,0 x 0,8 x 1,2 m Application: Mini tube bending machine with free bending head. Processing of precision steel tubes according to DIN 2391/C, material 35.4 NBK Ø 6 - 16mm. -With hydraulic drive -8-fold bending preselection angle up to 180 -Pipe stop length 1m -Emergency stop button -mobile with parking brake -pivoting pipe head (vertical in horizontal position) -required hydraulic oil = approx. 20 liters (e.g. Esso Nuto 32) Accessories: various bending tools *

Condition: new, Year of construction: 2025, Table milling machine minimax twf 55 es M 3 UP Professional workman's machine with motorized height and inclination adjustment of the milling spindle, four speeds and electronic control system Item number 5502266 Brand Holzkraft / SCM EQUIPMENT Equipment Aluminum sliding carriage ✔ Handle at sliding carriage ✔ FLEX ONE routing fence: heavy-duty professional design, automatic adjustment of the entire routing fence depending on the tool diameter, manual adjustment of chip removal, swing-away device, aluminum fence jaws with connecting strips Height adjustment of the spindle motorized. Telescopic miter fence with two folding stops Inclination adjustment of the spindle motorized Lsdpfjhp Rc Iox Affsta Cantilever table ✔ Ready 3 control: Programmed movement of the milling unit in two axes, Automatic adjustment of the entire milling stop depending on the tool diameter, Stepless adjustment via switch or automatic positioning system Curved milling protective hood ✔ Position of control elements Control panel at eye level, swiveling Eccentric clamp TECHNICAL DATA Dimensions and weights Length (product) approx. 1200mm Weight (net) approx. 510kg width/depth (product) approx. 2000mm Connection suction suction connection diameter 2 x 120mm Work table Working table length 1200mm Sliding carriage length 1200mm Working table width 530mm Sliding carriage width 360mm Table height 900mm Slide height 142mm Installation information Space requirement length 2800mm Machine body width/depth 846mm Space requirement width [...]

Condition: new, Year of construction: 2024, Panhans swivel milling machine type: 245/20 Solid German engineering Table milling machine with one-sided swiveling fixed milling spindle for the swivel range from -5° to +45.5° Positioning control for height and swivel adjustment with height zeroing and offset measurement travel Electronic position and speed displays 4 speeds 3000 / 4500 / 6000 / 9000 rpm Quick belt tensioning device Push button for spindle start and stop Left and right rotation Milling cutter quick clamping device Finely planed gray cast iron table with rigid frame support Lower control panel on rigid frame support Milling fence 216 total adjustment via handwheel and LCD display incl. cast fence plates and aluminum splitter tongues Machine socket Lockable main switch Mechanical motor brake Milling protection and pressure device GAMMA V 1629 Arc milling fence 1639 Tapoa Milling spindle 30 mm, non-replaceable CE-compliant GS tested Table size 1100 x 760 mm Table height 870 mm Milling spindle not exchangeable 30 mm Clamping height 140 mm Height adjustment 125 mm Suction nozzle 2 x Ø 120 mm Speed 3000 / 4500 / 6000 / 9000 rpm Color RAL 7035 light grey and Ljdpjr Ig H Tsfx Affjta RAL 5000 violet blue Net weight approx. 800 kg Equipment: Top control panel Swivel +-45 degrees Motor 7.5 Kw Centerx Extendable frame support Location: ex stock 54634 Bitburg - immediately available -

Condition: as good as new (ex-display), Year of construction: 2025, Minimax ti 55es LL - spindle moulder Figure shows 55 i T s standard version elite The professional craftsman machine with Swivel Milling spindle and 4 speeds. M Digital: motorized height adjustable and Tiltable Stable steel-cast iron construction Large dimensioned milling unit of grey cast iron, swivel up to 45 ° to the rear Display of the cutting speeds by LEDs Quick and easy change of speed of eccentric tension Right left rotation Display height and inclination 1/10 mm exactly Shaper fence heavy-duty professional: with fine adjustment via rack and pinion, with numerical display, ALU stop baking, 3-fold positioned for quick repeat of setting Ltededqzh Repfx Affja Scope of delivery: Aluminium milling stop baking Milling wheel arch guard Extension table left and right Model minimax ti 55es LL Item No. 5502252 Technical data Dimensions of the working table 2500 x 655 mm Formatschiebeschlitten commercial length of spindle dimensions 125 mm Max tool diameter 240 mm Max tool diameter lowerable 230 mm Max tool-Ø pin cutter 320 mm Spindle inclination 0-45 degree Speed 3500/6000/8000/10000 min-1 Engine power 400 V / 50 Hz / S6-40% 5.0 kW Suction nozzle diameter 2 x 120 mm

Condition: excellent (used), Year of construction: 1994, Holz Her Tilting Spindle Moulder with Holz Her Power Feeder Table extension on both sides with pull-out stop Swiveling spindle: Yes, -5 to +45° Height adjustment: manual Tilting adjustment: electric Fence adjustment: manual Height display: digital Tilting angle display: digital Fence position display: scale Spindle diameter: 30 mm Ltjdpfxexpm Evj Affea Speeds: 1500, 3000, 4500, 6000, 9000, 12000 rpm Motor power: 5 / 6 kW Motor brake: Yes, automatic Extraction connection: 2 x 120 mm Machine length: 1950 mm Machine depth: 1400 mm Weight: approx. 1100 kg Holz Her Power Feeder, type 1112 – 4 rollers Location: Ex stock 54634 Bitburg - Immediately available -