Used Stunning Tongs for sale (125)

Condition: used, Year of construction: 2004, fuel type: diesel, gearing type: automatic, Equipment: cabin, Manufacturer: SVETRUCK Type: TMF 15/11 Year of construction: 2004 Hours: 46.380 Engine: Volvo TWD 1240 VE kW / PS: 275 / 374 Weight: 57.500kg Payload: 19,000kg (when telescopic boom retracted) 11,000kg (when telescopic boom fully extended) Lifting height: 8,900mm max 7,200mm measured below the timber tongs Bsdpewlinujfx Aqrslh Area of the tongs: 5.5m² Depth of the tongs: 1,200mm

Condition: good (used), Koma Pigs stunning device This device is suitable for the electrical stunning of animals. From 2019, Regulation (EC) No 1099/2009 of 24 September 2009 concerning the protection of animals at the time of killing applies. According to the new regulations, every animal slaughtering plant should record the stunting parameters. This device has a factory-installed recorder of the deafening parameters, which measures the deafening parameters during slaughter and records them on an SDHC memory card placed in the recorder's socket. The device with the recorder gives the possibility of remote assistance when setting the de-stunting parameters. The operation  is based on the principle of automatic measurement of the body resistance of the deafened piece. In the ready-to-run state, there is only a low safe measuring voltage of approx. 15 V at the open electrodes of the forceps. When the electrodes are pressed against the animal's body, the resistance is measured and a deafening voltage of < 400 V is automatically applied, which is automatically switched off when the deafening process is completed (i.e. the electrodes are opened). Two electrodes are applied to the animal's head, while the third electrode, using a pneumatic actuator, is applied to the area of the heart, causing it to stop temporarily, as a result of which the blood stops flowing and the number of congested muscles decreases. By stopping the heart with the third electrode, it is possible to significantly reduce the incidence of adverse factors affecting the quality of the meat. Bedpfoy Edvtox Aqrjlh

Condition: used, Year of construction: 2018, controller model: , _____ Description: Year of manuf. : 2018 Control : Technical data Year of manufacture:2018 Pressing force approx.:3200 kN Folding length approx.:4420 mm Control system:TASC 6000 Projection:420 mm Free upright clearance approx.:3680 mm Usable installation height approx.:615 mm Machine weight approx.:23400 kg Equipment :- Sturdy machine frame :- Press beam, stress relieved with high bending strength :- Spherical bearing of the press beam (inclined position) :- Electro-hydraulic top drive with 4-cylinder technology :- Optical set-up and positioning aid :- Generous edge clearance :- Flat front covers :- Block hydraulics :- Electronic pressure compensator :- Measuring system with glass scale and deflection compensation :- Hydraulic oil in the machine (lifetime lubrication) :- Oil cooler :- Control cabinet cooling via air-to-air heat exchanger :- Modern machine design Extended equipment :- 6-axis backgauge system :- Hydraulic upper tool clamping Blodpfsyy Hgqjx Aqroh :- CNC crowning :- Work area lighting front and rear BendMaster (150) :- Sturdy base body and manipulator in cast aluminium construction :- Load capacity 150 kg, plate plus gripper :- Low floor track in welded construction :- Sheet sensor for contour detection :- Rotary feed-through for easy gripper change :- Gripper coupling on BendMaster :- Sensors for 4-axis backgauge system :- Electric drives :- Double sheet detection :- Regripping station NC :- Vacuum generation for suction gripper :- Platform (300 mm) for the bending press Extended BendMaster equipment :Extended BendMaster equipment - Track extension to 12 m :- Sensor system for 6-axis back gauge :- Gripper changing console :- Vacuum gripper, undefined :- Modular vacuum gripper with separation (material for 3 grippers) :- Gripper coupling :- Tong gripper :- Sheet removal station with linear axis :- Side door on right for safety fence

Condition: new, power: 346 kW (470.43 HP), fuel type: diesel, empty load weight: 15,520 kg, maximum load weight: 10,480 kg, overall weight: 26,000 kg, tire size: 315/80R22.5, axle configuration: 6x2, wheelbase: 4,800 mm, brakes: retarder, color: white, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, suspension: steel-air, number of seats: 2, loading space length: 6,500 mm, loading space width: 2,480 mm, loading space height: 1,000 mm, Equipment: ABS, additional headlights, air conditioning, cabin, central locking, crane, cruise control, differential lock, electronic stability program (ESP), fog lights, navigation system, onboard computer, power assisted steering, seat heater, traction control, trailer coupling, Vehicle location: Bovenden, Main building. 1x comfort seat, 2x bunks, seat heating, electric mirrors, heated mirrors, left electric window, right electric window, air conditioning, sun visor, cruise control, navigation system, electric glass roof, ABS (anti-lock braking system), traction control system (ASR), retarder, PTO (power take-off), automatic transmission, differential lock, fog lights, work lights, leaf and air suspension, last axle can be lifted and steered, trailer coupling air+light, aluminum tank, lashing eyes, underride protection, side aluminum protection, swinging tailgates, rear-mounted crane, emergency stop, grab control, high seat, 2-point hydraulic support, 2x hydraulic extensions, green environmental badge. Wheelbase: 4800 mm. Body: flatbed body with aluminum sidewalls & rear crane Atlas AK 170.2-A12 with high seat. New vehicle from stock! Bjdpfjxxbz Rjx Aqrolh Gearbox 12 TX 2621 TD with retarder, disc brakes on all axles, air conditioning, navigation system, 2x bunks, cool box, galvanized subframe! Load chart: 4.4m-3720kg, 6.3m-2550kg, 8.2m-1940kg. Loading height approx. 1300 mm! Pallet tongs available at extra cost! ACCESSORY DETAILS WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted!

Condition: used, Westtech Woodcracker W600 W820 W1000 W1350 W1800 Log Splitter Tongs Available immediately Westtech Woodcracker W600 - Jaw opening: 620 mm - Splitting force at 240 bar: 26 t - Dead weight (basic version): 295 kg - Recommended oil flow rate: 25–60 l/min Blodpjyfqc Sofx Aqroh - Recommended operating pressure: 190–250 bar - Carrier vehicle operating weight: 6 t - Optional: Autospeed valve - Optional: Rotator Westtech Woodcracker W820 - Jaw opening: 820 mm - Splitting force at 240 bar: 26 t - Dead weight (basic version): 360 kg - Recommended oil flow rate: 25–60 l/min - Recommended operating pressure: 190–250 bar - Carrier vehicle operating weight: 10 t - Optional: Autospeed valve - Optional: Rotator Westtech Woodcracker W1000 - Jaw opening: 1040 mm - Splitting force at 240 bar: 26 t - Dead weight (basic version): 580 kg - Recommended oil flow rate: 40–80 l/min - Recommended operating pressure: 190–250 bar - Carrier vehicle operating weight: 14 t - Optional: Autospeed valve - Optional: Rotator Westtech Woodcracker W1350 - Jaw opening: 1370 mm - Splitting force at 240 bar: 34 t - Dead weight (basic version): 950 kg - Recommended oil flow rate: 80–150 l/min - Recommended operating pressure: 220–270 bar - Carrier vehicle operating weight: 20 t - Optional: Rotator Westtech Woodcracker W1800 - Jaw opening: 1830 mm - Splitting force at 240 bar: 50 t - Dead weight (basic version): 1990 kg - Recommended oil flow rate: 100–190 l/min - Recommended operating pressure: 240–300 bar - Carrier vehicle operating weight: 20 t - Optional: Rotator Various versions and adapter plates available Price on request. We are an official Westtech Woodcracker sales and service partner, Magni telehandler sales and service partner, JCB construction equipment sales and service partner, Mercedes-Benz service partner, Iveco service partner, and with 800 used vehicles, one of the largest commercial vehicle dealers in Germany. We can supply the complete range of Westtech Woodcracker products for you! Rental available = More information = New: Yes Please contact Tobias Ebert for further information.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 820x610 saw band length 5850 x 41 x 1,3 mm band speed 15 - 100 m/min table height 800 mm total power requirement 5,5 kW weight of the machine ca. 4,45 t dimensions of the machine ca. 5,85 x 3,6 x 2,7 m 2-column band saw for quick cutting, K-tech 800H with pusher system P 15. P 30 (option), Fast, quiet and ergonomic cutting Bsdpfxsfgyife Aqrolh Special development for cutting profiles and beams as well as solid material. The material is fixed vertically on and section sides. The machine is from K-tech 800 H standard with an additional horizontal vice equipped. The interaction of the hydraulic Saw frame lowering, material positioning and the Pusher system is CNC controlled. The machines come standard with the environmentally friendly “B&S-Clean Cut cutting system” with minimal quantity lubrication equipped. This saves cleaning effort and is gentle Resources. CNC Control A CNC control allows programming of up to up to 90 cutting programs with different cut lengths, Quantities and mitres. The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 1250x600 saw band length 8140x54x1,6 mm band speed 15 - 90 m/min table height 855 mm total power requirement 7,5 kW weight of the machine ca. 4,96 t dimensions of the machine ca. 5,7 x 4,0 x 2,75 m 2-column band saw for quick cutting, K-tech 1200H with pusher system P 30. P 60 (option), Fast, quiet and ergonomic cutting Special development for cutting profiles and beams as well as solid material. The material is fixed vertically on and section sides. The machine is from K-tech 800 H standard with an additional horizontal vice equipped. The interaction of the hydraulic Saw frame lowering, material positioning and the Pusher system is CNC controlled. The machines come standard with the environmentally friendly “B&S-Clean Cut cutting system” with minimal quantity lubrication equipped. This saves cleaning effort and is gentle Resources. CNC Control A CNC control allows programming of up to up to 90 cutting programs with different cut lengths, Quantities and mitres. The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Blsdpfxefgyigo Aqroh Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 820x610 capacity 45 degrees: round 550 mm capacity 45 degrees: square 550 mm capacity 45 degrees: flat 550x600 mm capacity 60 degrees: round 370 mm capacity 60 degrees: square 370 mm capacity 60 degrees: flat 370x600/450 mm saw band length 7260 x 41 x 1,3 mm band speed 15 - 100 m/min table height 800 mm total power requirement 5,5 kW weight of the machine ca. 4,8 t dimensions of the machine ca. 5,85 x 3,7 x 2,7 m 2-column double miter band saw for quick cutting with pusher system P15. Option P30 Hydraulic saw frame lowering • NC controlled • Automatic angular positioning from + 60° to – 60° High quality automatic miter adjustment Special development for cutting profiles and beams. The highest positioning accuracy is achieved via the new “B&S positioning system”. reached. An intelligent NC control ensures smooth interaction of linear encoder and self-braking positioning motor in conjunction with a reliable hydraulic brake using large radial center positioning. The work table is supported by high-quality preloaded bearings, which ensure very smooth rotation. CNC Control Bjdpfx Ajfg E Hmeqrolh A CNC control allows the programming of up to 90 cutting programs with different section lengths, quantities and mitres. Positioning system gripping on both sides The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 1250x600 mm capacity 45 degrees: round 680 mm capacity 45 degrees: square 600 mm capacity 45 degrees: flat 870x600 mm capacity 60 degrees: round 580/550 mm capacity 60 degrees: square 530/450 mm capacity 60 degrees: flat 550x450 mm saw band length 8140 x 54 x 1,6 mm band speed 15 - 90 m/min table height 855 mm total power requirement 7,5 kW weight of the machine ca. 5,3 t dimensions of the machine ca. 5,75 x 4,2 x 2,75 m 2-column double miter band saw for quick cutting with pusher system P15. Option P30 Hydraulic saw frame lowering • NC controlled • Automatic angular positioning from + 60° to – 60° High quality automatic miter adjustment Special development for cutting profiles and beams. The highest positioning accuracy is achieved via the new “B&S positioning system”. reached. An intelligent NC control ensures smooth interaction of linear encoder and self-braking positioning motor in conjunction with a reliable hydraulic brake using large radial center positioning. The work table is supported by high-quality preloaded bearings, which ensure very smooth rotation. CNC Control Bljdpfxofg E Hns Aqroh A CNC control allows the programming of up to 90 cutting programs with different section lengths, quantities and mitres. Positioning system gripping on both sides The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Year of construction: 2001, condition: excellent (used), machine/vehicle number: R2D P1503, Spindle Ø (tong passage): 32 mm Max. Turning Ø: 140 mm Distance between the spindle noses: 720 mm Main spindle, mounting acc. To DIN 55026: KK 4 Passage in the draw tube: 32 mm Counter spindle, mounting acc. To DIN 55026: KK 4 Travel z: 510 mm Travel speed: 24 m / min Main spindle drive, AC motor: 10 kW Infinitely variable speed range: 0 - 8000 rpm Counter spindle drive, AC motor, power at 40% ED: 10 kW Blsdpfx Aqef Ddafsroh Infinitely variable speed range: 0 - 7000 rpm Disk turret tool system with directional logic, 25 holders Number of driven tools: 12 Rotation speed of the driven tools: 0 - 6000 rpm electr. Connection: 400 V Weight approx .: 3000 kg Required space: 2600 x 1980 x 2350 mm

Condition: used, mileage: 321,000 km, power: 294 kW (399.73 HP), first registration: 12/2015, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: white, gearing type: automatic, emission class: euro6, total width: 2,550 mm, total height: 3,820 mm, loading space length: 6,200 mm, loading space width: 2,500 mm, loading space height: 1,000 mm, Equipment: ABS, air conditioning, compressor, crane, * MAN TGS 26.400 with Palfinger Crane PK 20.501 L TEC 3 A, equipped with pallet tongs and high-seat controls - immediately available - * Diesel - Engine capacity: 12,419 cc - 294 kW / 400 hp - Euro 6 - Green emission sticker - * Tyre sizes: Front axle: 385/65 R 22.5 - 2nd axle: 315/80 R 22.5 - Rear axle: 385/65 R 22.5 Blodpfsym H Uyex Aqrsh * Original 321,000 km - Air conditioning - German vehicle - German vehicle documents - * Automatic transmission - Trailer coupling - Air conditioning - Good condition - Immediately ready for use - * Viewing by appointment only - * Contact person: Mr. Andreas Vogel * The information provided online is a non-binding description. * It does not constitute a guaranteed characteristic. * The seller is not liable for typographical or data transmission errors. * Subject to change, errors, and prior sale.

Condition: good (used), Pipe grabs, round grabs, laying tongs, round material grabs, scissor grabs Bjdpfxelyvdys Aqrolh -Pipe grab: unfortunately without type designation -Pipe diameter: approx. 400 to 750 mm, see photos -Dimension: 930/470/H1140 mm -Own weight: 124 kg

Condition: new, Year of construction: 2026, SEMI-AUTOMATIC DRILLING RIG “UNIBORFIX 50” With the UniBohrFix 50 drilling system, all profiles can be machined against a stop or with grippers. The Drilling is done manually using the lever, with the materials on the X-axis automatically pointing to the drive to the next drilling position. Easily drill entire programs or work with the stop plate quickly carry out individual drillings. The system is suitable for weights up to 100 kg. The facility also contains a minimum quantity spray unit with holder and spray can. The technical data of the standard version can be found in the table. If necessary, all components of the system can be adapted to your requirements. You can choose between different drilling machines, roller conveyors, select positioning systems and vices. Plantec configures the system so that it suits you perfectly! ADVANTAGES A sequence of holes is automatically executed at precise intervals. Potential operator errors are drastically reduced. Programming takes just a few minutes. Very good value for money. Significant reduction in manpower. Standard measuring lengths: 3,000mm 6,000mm Drill: Unimax 2 T Spindle MK2 Continuous drilling capacity 18 mm Speed ​​ranges: 100-2000rpm, 200-4000rpm Projection 225 mm Spindle/table distance 60-400 mm Adjustable vice with measuring linear display Positioning length stop: PD-100e Bljdpfx Aqegwt Sljreh control for automatic positioning Positioning: absolute or chain dimensions Easy to read LED display Trolley with DC servo motor Positioning accuracy +/- 0.1 mm/m Attachment arm with spring damping Stop plate with groove Memory control with 3,000 memory options Roller conveyors: RD-200/3 load capacity 200 kg/m Roll width 290 mm Roll diameter 40 / 50 mm insert sheets Struts for stabilization switch cabinet Available options: Minimum quantity spray system with spray head and holder Gripper tongs for clamping the material on the stop plate

Year of construction: 2025, operating hours: 15 h, condition: like new (used), functionality: fully functional, input current: 230 A, machine/vehicle number: 202505, Absolutely like new! Demo unit (price incl. 19% VAT) - Speed oven with non-stick cooking chamber - Suitable for cooking and heating food - TRIAC circuit for precise power control - Integrated exhaust air management from the cooking chamber Scope of delivery - Starter accessory set consisting of: - 1 × rectangular pan, smooth, 260 × 260 mm - 1 × round snack pan, Ø 190 mm - 1 × round snack pan, Ø 250 mm - 1 × tong for 50 bowls - 1 × turner, 360 mm - 1 × silicone tong, 260 mm - Power cable Housing & design - Color: Red / Stainless steel Technical data - Dimensions (H × W × D): 420 × 540 × 500 mm - Power: 3,000 W - Weight: 29.5 kg - Connection: 230 V / 50 Hz / 16 A The speed oven is a compact high-performance unit for professional use in the catering industry. It is suitable for rapid cooking, baking, and heating of various dishes, designed for efficient workflows with high output. The speed oven features a non-stick coated cooking chamber and integrated exhaust air management. Thanks to TRIAC circuitry, the device allows for precise operation and consistent power regulation. Low odor, enables roasting characteristics without fat or oils ... Functionality - Speed oven with non-stick cooking chamber - Suitable for cooking and heating food - TRIAC circuit for precise power control - Integrated exhaust air management from the cooking chamber Extensive accessories available, such as steak contact plates... (Source: Website Reamotion Delmenhorst) Bljdpfjyxy R Tox Aqreh

Year of construction: 2015, condition: ready for operation (used), This TELSONIC TelsoSPlice TS3-6 P3.6 wire welding sytem was manufactured in 2015. It features a 15" SVGA touch screen, a pneumatic unit, and a 3.6kW WeldHead. The machine includes a barcode scanner, keyboard, and a spacious 2000 x 1000 mm table. Consider the opportunity to buy this TELSONIC TelsoSPlice TS3-6 P3.6 Table. Contact us for more information about this machine. • System: TelsoSplice Plus • Technology: Ultrasonic wire splicing / wire compaction • Application: Ultrasonic welding of wire strands for splice production and compaction • Material Capability: Bare copper wires • Restriction: Wires must not be tinned • Plastic Welding Capability: Not suitable for plastic welding • Total Welding Counter: 1490 welds • Recorded Welds / Compactions: approx. 490 • Ultrasonic Frequency: 20 kHz • Ultrasonic Power (Welding Tongs): 3 kW • Generator Power: 3.6 kW • Amplitude Accuracy: Stabilized ±3 % • Wire Cross Section Range: 0.26 mm² – 40 mm² • Cylinder Force at 6 bar: 1750 N • Cylinder Force at 7 bar: 2040 N • Insertion Stroke (Opening): 19 mm / 10.5 mm • Maximum Tool Torque: 20 Nm • Maximum Air Supply Pressure: 10 bar • Maximum Operating Pressure: 7 bar • Compressed Air Quality: ISO 8573-1:2010 [2:3:2] • Pneumatic Connection: Pneumatic hose Ø8 mm • Voltage Supply: 3 × 400 V / 230 V • Power Supply Type: 3LNPE • Frequency: 50 – 60 Hz • Nominal Current: 3.3 A • Maximum Peak Current: 6.0 A eff • Power Factor: cos φ > 0.95 • Minimum Line Protection: 3 × 13 A slow-blow • Protection Class: IP20 • Control System: SPC Module-4 • Operating System: Windows Embedded Standard 7 • Touch Panel PC: 15" SVGA Touchscreen • TelsoSplice Software Version: 3.5 • Version: 3.5.50929 • Microsoft Framework Version: 4.0.30319.34209 • Ultrasonic Generator: MAG • Generator Output Power: 3.6 kW • Weld Head: TS3-6 • Power Cable: 3 × 400 V / 230 V MAG/SPC-4 • Power Cable Length: 3 m • Pneumatic Unit: TelsoSplice TS • Adapter / Power Cable: MAG/SPC-4 • Rack Housing: 19" 8U • Emergency Stop: TelsoSplice Table E-Stop • Foot Switch: TelsoSplice Foot Switch Bjdpfsx D E A Asx Aqrolh • Barcode Scanner: Manhattan CCD Long-Range • Keyboard: US Layout • Key Set: TelsoSplice Key Set • Cable Set: TelsoSplice Table / Standing Version • Machine Table: TelsoSplice Table L • Table Size: 2000 × 1000 mm • Complete System Weight (Table Version): approx. 103 kg • Operating Temperature Range: 10 °C – 40 °C • Humidity Range: 20 % – 80 % (non-condensing)

Condition: good (used), Year of construction: 1995, Format: max 510 x 310 x 60 mm; min 140 x 100 x 3 mm Book block thickness: max 60 mm; min 3 mm Cover format: max 642 mm; min 203 mm Output: max 12,000 c/h Bedjquuxbopfx Aqrelh Equipment Gathering machine - 15 stations - 15 feeders 201 S - Vibrating element 3642 Perfect binder - 23 Tongs - Pincer pitch 24" - Vibrating station - Milling and roughening station - Hotmelt back gluing unit - Hotmelt side gluing unit - 2 premelters - Shingled cover feeder - 2nd SF cover pressing - Laydown device

Condition: used, Inverter welding machine for manual electric welding IMS - GYS type PROGYS FLEX 280A CEL MMA welding machine, inverter welding machine, manual electric welding inverter Serial no. IEC 60974 Year of manufacture 2020 Power with mains operation 400 Volt (40% ED) 280 Amp. Power with mains operation 400 Volt (60% ED) 200 Amp. Power for mains operation 400 Volt (100% ED) 170 Amp. Power for mains operation 230 Volt (40% ED) 200 Amp. Power for mains operation 230 Volt (60% ED) 180 Amp. Power for mains operation 230 Volt (100% ED) 150 Amp. Adjustment range 5-280 Amp. stepless Mains connection 230 / 400 Volt, 50 Hz. - Operating voltage from 110 to 480 volts alternating current - Adapts fully automatically to the existing mains supply - equipped with 16 Amp. CEE plug for 400 Volt mains voltage - Hot-start function (optimizes the ignition behaviour, simplifies the welding start of electrodes that are difficult to ignite) - Anti-stick function (optimizes electrode guidance and prevents the electrode from sticking) - Arc-Force function (optimizes arc stability and improves penetration) - Digital display - Plug socket for remote control connection - Earth cable with plug connection - Electrode tongs with 3 meter cable and plug connection - Stick electrode welding, can be used for all electrode types up to Ø 5 mm - TIG-DC welding (without TIG hosepack) - The device may be connected to a flexible three-phase power supply between 110 V and 480 V or to a fixed three-phase 400 V power supply (50 - 60 Hz) plus ground wire. This appliance may only be connected to a 3-phase power supply system with 4 conductors, where the neutral conductor is earthed. Blodpfevg Rh Tjx Aqrjh Dimensions (appliance without cable) L x W x H 470 x 270 x 430 mm Weight (without cable) 23 kg New, unused

Year of construction: 2014, condition: used, functionality: fully functional, machine/vehicle number: Multiple on request, Continuous Potato Peeling Line – Tong Engineering & Sormac Equipment This continuous potato peeling line combines reliable Tong Engineering handling equipment with efficient Sormac peelers to create a complete solution for high capacity potato processing. Designed for consistent product flow and dependable performance, the system is well suited to processors looking to streamline their peeling operation. The equipment moves potatoes smoothly from cleaning and peeling through inspection, treatment, and final product safety checks. With trusted machinery from Tong and Sormac, this line delivers both efficiency and durability in demanding production environments. Equipment Included Tong Engineering De-Stoner The process begins with a Tong de-stoner, which removes stones, soil, and heavy debris from incoming potatoes. This stage protects downstream equipment and ensures cleaner product enters the peeling process. Two Sormac Continuous Peelers The line includes two Sormac continuous peelers designed for high capacity peeling while minimising product loss. These machines efficiently remove potato skins while maintaining consistent throughput for industrial potato processing operations. Tong Engineering Surge Tank A Tong surge tank regulates product flow between processing stages. This buffer helps maintain a steady supply of potatoes through the system and prevents bottlenecks during production. Tong Roller Inspection Table The Tong roller inspection table allows operators to visually inspect peeled potatoes and remove defects. Rotating rollers spread the product evenly, improving visibility and making quality control easier. Tong Dip Tank with Dosing Unit A Tong dip tank with integrated dosing unit allows potatoes to be treated with anti-browning or preservation solutions. This step helps maintain product appearance and supports shelf life after peeling. Loma IQ3S Metal Detector The final stage of the continuous potato peeling line is a Loma IQ3S metal detector, which checks the finished product for metal contamination and helps meet food safety standards. Key Benefits Complete continuous potato peeling line for commercial processing Combination of Tong Engineering handling equipment and Sormac peelers Designed for efficient stone removal, peeling, inspection, and treatment High throughput suitable for industrial potato processing Integrated metal detection for product safety Reliable equipment built for demanding production environments Suitable Applications This equipment is ideal for: Potato processing facilities Fresh produce packing operations Blodpfx Asytn H Doqrjh Ready meal manufacturers Vegetable processing plants Enquiries If you are interested in this continuous potato peeling line, please get in touch for further information, pricing, and availability. The system offers a dependable solution for large-scale potato processing. Five individual lines available We hold a wide range of new and used food processing machinery in stock, some of which may not be showing on our website. If you have any additional requirements please get in touch

Condition: excellent (used), Manual, water-cooled spot welding tong Make: DALEX, Type 3218-4 with double-stroke mechanism with cardan suspension and hanging bracket Rated power at 50% duty cycle: 16 kVA Secondary short-circuit current: 13.5 kA Secondary open-circuit voltage: 3.4 V Bsdpfx Ajyq R Dteqrelh Electrode force: 240 daN Arm reach: 650 mm with 10 m connection cable with asynchronous welding control RB 11 with mains connection cable and CEE plug

Condition: excellent (used), Hand-operated, water-cooled spot welding tong Brand: DALEX, Type 3218-4 with double stroke mechanism Blodpfxeynl Sge Aqroh cardan suspension and mounting bracket Rated power at 50% duty cycle: 16 kVA Secondary short-circuit current: 13.5 kA Secondary open-circuit voltage: 3.4 V Electrode force: 240 daN Throat depth: 500 mm with 10 connection cables including synchronous external control 1=01 TT with 3 m mains cable and CEE plug

Condition: excellent (used), Hand-operated, water-cooled spot welding tongs Brand: DALEX Type: 3218 Rated power at 50% duty cycle: 16 kVA Secondary short-circuit current: 13.5 kA Electrode force: 270 daN Arm spacing: 130 mm Arm reach: 500 mm Bodpfoykvd Eox Aqrelh With double-stroke mechanism Cardan suspension and suspension bracket 10 m connection cable Asynchronous welding control RB 11 With 8-step switch Current time: 3-100 cycles

Year of construction: 2015, condition: like new (used), Servo-motorised 3G-X-forceps / modular welding gun for robots was mounted on KUKA robots - the adaptation to such is included Electrode force max. 6kN at 500mm radius X-tongs for Cu-arms with diameter 54mm MF transformer 560V / 1kHz, 56kVA Ratio 1:70 - U20, 7.2V with measuring coil 150 mV / kA and thermal switch Servomotor 8-pole 300V - 20kN maximum power Working stroke 95mm + 10mm reserve PDIV display Resolver 8-pin Spindle pitch 5mm Bljdpfx Aqod Eaz Tersh Electrode arm for 3G pliers, projection approx. 400mm with brake (24VDC 1A) as required for KUKA robot Long 90 ° L console complete tube package including control and cooling tubes enclosed

Condition: new, cutting diameter 410 mm saw band length 5800 x 41 x 1,3 mm table height 750 mm capacity 90 degrees: flat 700 x 410 mm capacity 45 degrees: round 410 mm capacity 45 degrees: flat 500 x 410 mm capacity 45 degrees: round links 410 mm capacity 45 degrees: flat links 430 x 410 mm Bledpsx Sr Drsfx Aqrsh capacity 30 degrees: round 320 capacity 30 degrees: flat 320 x 410 15 - 150 m/min workpiece weight max. 250 kg/m kg 5,5 kW 3200 kg 4500 x 2800 x 2000 mm - The ergonomic panel control can be networked and offers various options Option packages * Teleservice for remote maintenance * Setting sawing programs in the AV * Import of sawing programs from CAD with DSTV interface and data export - Automatic material feed: - In a compact design for shorter sections or with flexible insertion tongs Available in almost all lengths - Exact positioning of the material using servo positioning technology - Pioneering electric saw feed with ball screw: - highest cutting performance and quality, while being gentle on the saw band - Consistent use of the most modern recirculating ball bearing systems: - smooth-running, highly resilient, low-maintenance and play-free - Unique and patented double miter system: - Material is always clamped at right angles Furnishing: - Automatic cutting pressure and feed monitoring - Frequency-controlled AC drive 15-150 m/min, 5.5 kW - Hydraulic material full stroke clamping - Automatic movement of the vices - Saw frame height adjustment automatically - Minimum speed and saw band monitoring - Electric miter tilting via servo motor - Visualized program input with CNC control - Integrated MEBA pliers insertion system from 5-2300 mm per stroke with integrated roller conveyor *Special equipment: - Laser light for cutting line display/marking saws - Chip brush driven - Micro dosing system - Clamping pressure regulation - Material bundle tension - Job menu - Material database - Zero stop - Scraper belt conveyor for optimal chip disposal, 2000 mm long - Cutting progress control

Year of construction: 2014, condition: used, Multiweigh 10 heads Multihead weigher. Blsdpfxjubf A Ne Aqreh Stunning multihead weighers from Multiweigh. They are in a very good condition ready for production. - Large stainless steel buckets - Ridigized - 10 heads with in-feed ring - Collection gate

Condition: used, Pipe gripper, round gripper, laying tongs, round material gripper, scissor gripper, pipe laying device -Manufacturer: Siegert, round material gripper round pliers type RZ -Gripping range: 50 to 250 mm Bljdsrkp Nqspfx Aqreh -Load capacity: 250kg -Dimension: 630/250/H450 mm -Town weight: 11 kg