Used Solvent Recovery Distillation for sale (1,061)

Condition: used, Year of construction: 2015, Length 12000 mm Width 9000 mm Used manual overhead conveyor system with a SCHUKO paint mist extraction unit and a warm-air supply system. Includes a cross-flow heat exchanger (heat recovery) and a manual overhead conveyor; in very good, well-maintained condition. Manufactured 2015–2016. ----- Sold on behalf of a client! The system is still in operation and available for inspection. Price is ex-site; dismantling to be performed by the buyer ((Scissor lift and forklift available on-site)). Group 1: Dry-type paint mist extraction system, model FARBMEISTER: ----- Model FARBMEISTER-25/30, including a stationary paint mist extraction wall with dry-type filtration. Baffle/filter area: H x W 2,790 x 3,140 mm (cardboard filter cells). Features a centrally positioned, solid baffle panel designed to reduce the maximum required airflow, tailored to the specific frames and casements being painted. Includes an additional pull-down pre-filter. This reduces the effective extraction area—and consequently the total airflow—from a standard ~14,000 m³/h to the required 10,500 m³/h. Also includes a 250 mm deep extension around the perimeter (left, right, and top) to improve the capture of overspray. A high-performance centrifugal fan (model L-EX 500) with a 5.0 kW motor, capable of an exhaust air volume of 10,500 m³/h (free-blowing), including all necessary ductwork and components to construct and install the extraction system—extending through the wall to the outside—as well as a manually adjustable exhaust air damper. Group 2: Warm Air/Supply Air System for the Spray Booth: Gedpfx Ags Ahkkhs Usui ----- BB 1,100 warm air/supply air system for the spray booth, including a supply air unit (model WZL110-com) equipped with an integrated heating coil (hot water connection, supply temperature +80°C). The unit has an air capacity of 10,500 m³/h and a 5.0 kW motor. The required heating capacity, based on a temperature differential (Delta-T) from -15°C to +22°C, is 137 kW. The system features an automatic louver damper at the air intake to seal off the ductwork and prevent cold air from entering when the system is not in operation. It also includes an explosion-proof warm-air thermostat designed to shut down the system in the event of a loss of heating capacity (hot water supply). This group encompasses all ductwork and supply air components, spanning from the external air intake to the air outlets in the distribution ceiling located above the spray wall. A cross-flow plate heat exchanger for heat recovery from the exhaust air duct leading outdoors, while simultaneously preheating the fresh air drawn in from outside. With an exhaust air temperature of +20°C and a fresh air temperature of -12°C, this results in an energy saving of approximately 58 kW of heating capacity. Includes all necessary duct and pipe components for integrating the exhaust and supply air lines with the plate heat exchanger, in accordance with the attached planning drawing. Also includes a maintenance/repair switch and a differential pressure monitor for supervising the intake filter. Please note that the heat exchanger core must remain easily accessible for routine maintenance and cleaning. Group 3: Electrical System Control for Paint Mist Extraction: ----- Electrical system control for paint mist extraction...

Condition: ready for operation (used), Year of construction: 2019, functionality: fully functional, machine/vehicle number: h288 di, power of vacuum pump: 11 W, overall weight: 4,900 kg, PRICE REDUCED: €29,000 → €25,000 (excluding VAT) – machine available immediately Resta automatic mattress packaging machine: integrated compression and decompression The Resta mattress packaging machine is an automatic packaging machine dedicated to the industrial packaging of mattresses. In practice, on your production line, this machine performs double packaging with compression and then decompression of the mattress, while protecting it in a suitable film. Advantages of mattress packaging in production and distribution First and foremost, an efficient mattress packaging machine reduces transport volume by 70 to 80%. The mattress remains compressed during transit and then returns to its original shape upon arrival. In practice, you save storage space and reduce logistics costs. Automated compression: mattresses packaged in PVC or plastic film, without manual intervention Easy decompression: the mattress returns to its normal shape in the store or at the customer's location Optimized transport: significant reduction in volume, with more space in the truck and in storage Preparation for sale: final presentation of the mattress in appropriate commercial conditions Vacuum packaging machine: protection and transport of the mattress What really changes in production is material compatibility. The Resta mattress packaging machine adapts to different types of mattress films, PVC film or plastic film, and ensures a hermetic seal. The fully automatic packaging process avoids manual handling, limits the risk of tearing, and maintains consistent quality. Compatible with spring and foam mattresses Ideal when your production mixes spring and foam mattresses. This packaging machine handles both types without major reconfiguration. The equipment handles both bagged mattresses and compressible structures equally well, simplifying workshop organization. Spring mattresses: compression without damaging the springs, thanks to a progressive hydraulic system Gsdpfx Aszmpvrjg Usui Foam mattresses: adaptation specific to the product, with rapid shape recovery after compression Compatible with PVC film and other specialized packaging films Professional sealing: hermetic closure of the film to protect the mattress during transport Industrial applications and mattress packaging processes In practice, on an industrial mattress packaging line, this Resta automatic packaging machine is integrated after the [omitted: the text stops mid-sentence]. Special feature: allows double independent packaging (two separate bags) in the same space as a standard packaging machine, thanks to two superimposed polyethylene rolls. It also allows single or customized packaging (two different rolls, automatic change according to programming). The feeding belt and detachable press also allow packaging of bed bases. Manual and/or automatic operation, interfaceable with barcodes or RFID on the production line. Official technical specifications: Weight: 4,900 kg Electrical consumption: 11 kW Compressed air: 6-10 bar Power supply: 400V – 50Hz three-phase Available options: Press with 2 or 4 cylinders Reinforced hoist Motorized cradle for additional customization rolls Kit for removing polyethylene waste

Condition: excellent (used), mileage: 274,950 km, power: 162 kW (220.26 HP), first registration: 03/2020, fuel type: diesel, axle configuration: 4x2, wheelbase: 4,200 mm, fuel: diesel, fuel tank capacity: 400 l, brakes: engine braking, color: red, driver cabin: day cab, gearing type: automatic, emission class: euro6, suspension: air, permissible axle load (axle 1): 3,400 kg, permissible axle load (axle 2): 5,600 kg, Equipment: AdBlue, EBS, USB port, air conditioning, central locking, cruise control, differential lock, electric window regulation, electronic stability program (ESP), fog lights, navigation system, onboard computer, power assisted steering, soot filter, tachograph, traction control, = Additional Options and Accessories = - Alarm system - Aluminum fuel tank - Rear work lights - Front work lights - Armrest - Audio controls on the steering wheel - AUX input - Outside temperature display - Construction lighting - Becker holder - Leaf spring suspension - DAB radio - Differential lock - Differential lock - Tachometer - Power mirrors, heated - Additional lighting - Driver's seat height adjustment - Enclosed cab - Speed limiter - Tinted glass - Hydraulics - Adjustable steering wheel - Adjustable driver's seat height - Folding exterior mirrors - Air conditioning - LED lighting - Air suspension - Center armrest - Multifunction steering wheel - Particle filter - Radio/CD player - Rotating beacon - Reversing camera - Disc brakes - Headlight height adjustment - Sun visor - Lane keeping assist - Immobilizer - Touchscreen - Automatic preheating - Winch - Power take-off (PTO) - Power take-off (PTO) = Further Information = General Information Year of construction: 2020 Cab: CC Technical Information Number of cylinders: 4 Engine displacement: 4,580 cc Axle Configuration Brakes: Disc brakes Front axle: Max. axle load: 3400 kg; Steered; Axle brand: Hankook; Tire tread left: 70%; Tire tread right: 70% Rear axle: Double tires; Differential lock; Max. axle load: 5600 kg; Axle brand: Kumho; Tire tread left inner: 70%; Tire tread left outer: 70%; Tire tread right inner: 70%; Tire tread right outer: 70%; Suspension: Air suspension Weights Unladen weight: 6,425 kg Payload: 1,575 kg GVW: 8,000 kg Condition Technical condition: very good Optical condition: very good Damage: none Gujdpfxe Aibn Rj Ag Uei Financial Information Price: On request = Company Information = Nidro cars Holland is located in the center of the country and is the right place to purchase your car, van or truck. The indicated price is the 'internet take-away price'. For questions or a test drive, please contact us: SEE OUR ENTIRE STOCK AT All trade-ins are possible! (Our advertisements are compiled with great care, but no rights can be derived from the content).

Condition: used, mileage: 86,160 km, power: 315 kW (428.28 HP), axle configuration: 6x2, color: white, driver cabin: sleeper cab, gearing type: automatic, suspension: air, total length: 95,400 mm, total width: 25,500 mm, total height: 40,000 mm, Equipment: ABS, EBS, air conditioning, - Braking system For inquiries regarding the vehicle, please contact Mr. Seidel (at phone number...). Mercedes-Benz Actros 2543 L 6x2 BDF interchangeable chassis Gedpfe Akiy Rox Ag Uoui Rear liftgate: Dautel DS 1500 VA (1,500 kg), P5Z interchangeable platform frame, 715/745 cm H=132 cm, A1A front axle air-suspended, A1D front axle 8.0 t, A1Z front axle, angled design, A2E rear axle, bevel gear 440, hypoid, 13.0 t, A4Z trailing axle, 7.5 t, can be unloaded, can be lifted, A5H axle ratio i = 2.611, B1B electronic braking system with ABS and ASR, B1E electronic compressed air supply unit, high, B1F heater, electronic compressed air supply unit, B2A disc brake, on front and rear axle, B3H secondary water retarder, B4A condensate monitoring, for compressed air system, B4M compressed air tank, steel, B4Z compressed air tank, additional, B5B trailer brake, 2-line, C0Z frame overhang 1950 mm, C2P wheelbase 4600 mm, C6C steering, 1-circuit, C6P power steering pump, electronically controlled, C6U additional stabilizer, rear/trailing axle, C7F front underrun protection (ECE), aluminum, C7J battery carrier, batteries side by side, C8I splash guard (EC), front, C8Y underbody paneling, aerodynamic, D1B driver's air-suspended seat, standard, D1P passenger's air-suspended seat, comfort, D2M seat back, release, passenger seat, D2N seat back, release, driver's seat, D2W armrests, on both sides, passenger seat, D3B comfort bunk, lower, D3Q seat cover, velour, D4T curtain, transverse in front of bunk(s), D6F air conditioning, D6I waste heat recovery, D6M auxiliary hot water heater, cab, D7G storage compartment cover, driver and passenger side, D7J drawers, under bunk, D7R storage flaps, above windshield, D8A roof hatch/ventilation flap roof, E4A communication interface (KOM), E4C additional functions, for body manufacturer, E4W start assist, speed limitation 30 km/h, E5H switch for night driving lights, E6A trailer socket 24 V, 15-pole, E6E adapter, 15-pole to 2x7-pole socket, E7F cable remote control for air suspension, F0F side module, N3 vehicle, F0X mirror cover, on-road vehicle, F1D L cab ClassicSpace, 2.30 m, tunnel 170 mm, F3B cab suspension, comfort, steel-sprung, F3W cab tilting mechanism, mechanical-hydraulic, F4G cab side wall, closed, right, F4H cab rear wall, without window, F4X storage compartment exterior flap, left, F5Y A-pillar trim, F6C windshield tinted, F6I front mirror, heated, F7A bumper, corners made of plastic, F7C bumper, center part with towing loops, F7X cab entrance left/right, fixed, F8E locking system, with central locking, F8F comfort locking system, G0U driving program economy, G2B transmission G 211-12/14.93-1.0, G5A single-plate clutch, G5G Mercedes PowerShift 3, I2E tires tubeless, 315/70 R 22.5 front/front lift axle/rear lift axle, I2F tires tubeless, 315/70 R 22.5 rear axle, I4C wheel formula 6x2 ENA, I5E 25.0-tonner, I6I vehicle production plant Wörth, I6X air suspension, rear axle, J1B instrument cluster, 10.4 cm, with additional displays, J1R tachograph digital, EC, speed, ADR, J1S tachograph manufacturer VDO, J2A CD radio, J2K speakers, 2-way system, J9A pre-wiring for CB radio, 12 V, DIN socket, J9D pre-wiring for toll system, J9L pre-wiring FleetBoard for J3J, J9X deletion of Truck Data Center, JESM socket VG96917, 2-pole, on frame, JETC battery disconnect switch. electronic, switch in cab and on chassis, JQ8F hand lever, above, for trailer coupling, JQBF drawbar coupling Ringfeder, K4D, ECE R-55, K0T main tank, left, K1C tank 290 l, le

Condition: used, mileage: 42,000 km, power: 118 kW (160.44 HP), fuel type: diesel, gearing type: mechanical, emission class: euro6, color: white, Equipment: ABS, air conditioning, central locking, cruise control, immobilizer system, Number of doors: 4 Year of manufacture: 2023 Year of construction: 2023 Cab: double VAT/margin: VAT qualifying = Additional options and accessories = - Airbag - Alarmsysteem class 1 - Camera system - Electrically adjustable exterior mirrors - Electrically operated windows - Lane Assist - Outside temperature display - PTO - Rear air suspension - Reversing camera Gusdpfxozzxy Ns Ag Uoi = Remarks = 7-person version with the Insoli System. LIKE NEW.

Year of construction: 2020, operating hours: 14,099 h, condition: excellent (used), machine/vehicle number: S0055742, used ALMIG Belt XP 22 - (8 bar) oil-injected screw compressor Gusdpfxoix Aiyo Ag Uei with integrated heat recovery with Aircontrol Premium controller Operating hours: 14099 Bh Pressure: 8 bar Rated power: 22 kW Delivery quantity: 3.70 m³ / min Sound level: 74 dB (A) Compressed air outlet: G 1 " Dimensions length x width x height: 1250 x 880 x 1515 mm Weight: 681 kg Visit our store we have a lot of used and new compressors on stock.

Condition: excellent (used), mileage: 255,377 km, power: 162 kW (220.26 HP), first registration: 05/2020, fuel type: diesel, axle configuration: 4x2, fuel: diesel, fuel tank capacity: 400 l, brakes: engine braking, color: red, gearing type: automatic, emission class: euro6, Equipment: ABS, AdBlue, EBS, USB port, air conditioning, central locking, cruise control, differential lock, electric window regulation, electronic stability program (ESP), fog lights, navigation system, onboard computer, power assisted steering, soot filter, tachograph, traction control, = Additional options and accessories = - Alarm system - Rear work light - Front work light - Armrest - Audio controls on the steering wheel - AUX input - Outside temperature display - Construction light - Becker mount - Heated mirrors - Leaf spring suspension - DAB radio - Roof cover - Sunroof - Differential lock - Differential lock - Tachometer - Power mirrors, heated - Extra lighting - Driver's seat height adjustment - Speed limiter - Tinted glass - Hydraulics - Adjustable steering wheel - Cab - Folding exterior mirrors - LED lighting - Air suspension - Center armrest - Multifunction steering wheel - Particulate filter - Radio/CD player - Rotating beacon - Reversing camera Gedpfjz Tlb Asx Ag Ujui - Disc brakes - Headlight height adjustment - Sun visor - Touchscreen - Immobilizer - Winch - Power take-off (PTO) - Power take-off (PTO) = Additional information = Year of manufacture: 2020 Front axle: Steerable Number of cylinders: 4 Engine displacement: 4,580 cc Unladen weight: 6,425 kg Technical condition: very good Optical condition: very good Damage: none Price: Upon request = Company information = Nidro cars Holland is located in the center of the country and is the right place to purchase your car, van, or truck. The stated price is the 'internet take-away price'. For questions or a test drive, please contact us: SEE OUR ENTIRE INVENTORY AT All trade-ins are possible with us! (Our advertisements are compiled with great care, but no rights can be derived from the content).

Condition: good (used), mileage: 506,631 km, power: 162 kW (220.26 HP), first registration: 11/2019, fuel type: diesel, tire size: 245/70R17,5, axle configuration: 4x2, wheelbase: 4,500 mm, fuel: diesel, color: red, driver cabin: day cab, gearing type: automatic, number of gears: 6, emission class: euro6, suspension: steel-air, total length: 8,480 mm, total width: 2,400 mm, total height: 2,750 mm, loading space length: 5,940 mm, loading space width: 2,290 mm, Equipment: ABS, Bluetooth, air conditioning, central locking, cruise control, electric window regulation, navigation system, power mirror, seat heater, tachograph, traction control, = Additional Options and Accessories = - Heated mirrors - Digital tachograph - Fixed - Halogen lamp - Short cab - Manual - Auxiliary drive - Pump - Radio/cassette - Reversing camera - Lane departure warning system - Fabric - Blind spot sensor - Winch = Notes = Number of axles: 2, Configuration: 4x2, Unladen weight: 7900 kg, Gross vehicle weight: 11990 kg, Total tank capacity: 100 liters, Fifth wheel coupling: Fixed, Number of differentials: 1, Winch, Suspension type: Air suspension, Type of cab: Short cab, Cruise control, Trip recorder (control unit), Digital tachograph, Air conditioning, Electric windows, Electric mirrors, Radio/cassette, GPS navigation, Color: Red, Heated mirrors, Reversing camera, Lighting type: Halogen lamp, Lane departure warning system, Climate control, Seat heating, Bluetooth, Blind spot sensor, Flashing lights, Engine power: 162 kW (217 hp), Number of cylinders: 4, Engine capacity: 4580 cc, Fuel: Diesel, Euro: 6, Transmission type: AS-Tronic, Transmission type: ZF, Gears: 6, Power steering, ABS, ASR, Auxiliary drive, PTO type: 1, System type: ., Pump, Central locking, Seat arrangement: 1+1, Seat cover: Fabric, Seat adjustment: Manual = Additional Information = Transmission Guodpfj Ahwzyox Ag Uei Transmission: ZF, 6 gears, Automatic Axle Configuration Tire size: 245/70R17.5 Brakes: Disc brakes Axle 1: Steered; Tire tread depth left: 11 mm; Tire tread depth right: 11 mm; Suspension: Leaf spring suspension Axle 2: Dual tires; Tire tread depth left inside: 4 mm; Tire tread depth left outside: 5 mm; Tire tread depth right inside: 4 mm; Tire tread depth right outside: 7 mm; Suspension: Air suspension Weights Unladen weight: 7,900 kg Payload: 4,090 kg GVW: 11,990 kg Functional Loading platform height: 115 cm Pump: Yes Condition Technical condition: good Optical condition: good Damage: none Number of keys: 2 Financial Information Leasing price: €770 per month (default, 60 months); Inquire for further information and terms Identification Registration number: KLEYN1 = Company Information = Kleyn Trucks is one of the largest independent used vehicle dealerships in the world. Here you can choose from a constantly changing stock of 1200 used trucks, tractor units, and trailers. Our range includes all European brands from various years of manufacture and price ranges. Why buy from Kleyn Trucks? Simple! • Large, rapidly changing inventory • Recognizable quality • A good price • Proper business practices • We speak many languages • We understand our customers • Support for import and transport • (Export) registration is quickly arranged • Expert technical services • The security of "recognizable quality" • And more... Please visit our website for special offers and a complete inventory: Leasing through Kleyn Trucks is possible in most European countries! Quickly calculate your leasing rate and submit a request via our website. Inquire directly about our European warranty package.

Condition: used, mileage: 345,321 km, power: 127 kW (172.67 HP), first registration: 05/2022, fuel type: diesel, axle configuration: 4x2, wheelbase: 4,800 mm, fuel: diesel, emission class: euro6, number of seats: 2, total length: 8,700 mm, total width: 2,550 mm, permissible axle load (axle 1): 5,000 kg, permissible axle load (axle 2): 9,440 kg, Number of doors: 2 Year of manufacture: 2022 Godpj Ahga Rofx Ag Ujui Maximum front axle load: 5000 kg Maximum rear axle load: 9440 kg Number of cylinders: 6 Engine displacement: 6,700 cc Unladen weight: 7,433 kg Payload: 6,567 kg GVWR: 14,000 kg = Company information = Hello

Condition: used, Desktop Metal Desktop Metal 3D Printer Complete System 3D Metal Printer Studio System from Desktop Metal Complete system: 3D printer + debinding machine + sintering furnace Desktop Metal The three-part solution includes a 3D printer, debinder, and furnace. Manufacturer: Desktop Metal Model: Desktop Metal Studio System Operating condition: Used (Good) Year of manufacture: 2019 Includes: Bound Metal Deposition (BMD) technology Features: Printed materials: Metal Technology: FDM Application: Industrial Other features: Office X-axis travel: 30 cm (12 in) Y-axis travel: 20 cm (8 in) Guodpfjzd Tllox Ag Uoi Z-axis travel: 20 cm (8 in) Description: In contrast to laser-based systems that selectively melt metal powder, the printer extrudes bound metal rods – similar to an FDM printer. This eliminates the safety requirements often associated with 3D metal printing, and enables new features such as the use of closed-cell fillings for lightweight strength. Desktop Metal Studio Debinder (Delamination machine) Fully automatic debinding Cleaning tank: 17.4 L (in process) / 22.5 L (storage) Description: The debinder prepares green parts by dissolving the primary binder for sintering. With a low-emission design, it requires no external ventilation and is safe for an office environment. Automatic liquid distillation and recycling mean that no refilling is required between cycles. Desktop Metal Studio Sinter Furnace Hybrid technology (microwave & conventional heating elements) Build volume: 305x205x205 mm Carbon housing Gas supply: 2 x 900 L gas cylinders Heating power: 20 kW Function: Sintering Configuration: Chamber Heat source: Gas Other features: High temperature, automatic Maximum temperature: 1,400 °C (2,552 °F) Description: Fully automated and sized to fit through an office door, the furnace delivers industrial-grade sintering in an office-friendly package. Built-in temperature profiles, tailored to each design and material, ensure uniform heating and cooling without the residual stresses that occur in laser-based systems. Condition: used Scope of delivery: (See image) (Changes and errors in technical data, information is subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: good (used), Pharmatec 500-S4 Multistage pressure column distillation unit Gjdsyfhtnjpfx Ag Ujui Stainless, designed for the production of sterile, non-pyrogenic water for injection (WFI), all mounted on skid, four column system, 660 l/h pressurized heating steam, 4Bar, adjustable controls, 3Ph

Condition: good (used), Code: 0521 Brand: COLOMBO Model: AM 33 A/F Automatic working centre for wooden window and door frames Technical specifications: Tenoning side: Tenoning carriage 1100 x 1100 mm Feed speed adjustment Rotating chip guard Extendable aluminium guide with millimetre scale and reference stops Blade diameter 400 mm Hole 30 Blade motor power 3 Kw Electronic horizontal movement Pneumatic vertical movement Suction inlet diameter 80 mm Counter-supported tenoning spindle Useful length 600 mm Spindle diameter 50 mm Max tool diameter 320 mm Spindle rotation speed 3200 rpm Motor power 7,5 Kw Electronic vertical positioning with continuous axis and recirculating ball screw N° 2 suction inlets diameter 1500 mm Profiling side: Fittings spindle Spindle diameter 50 mm Useful spindle length 160 mm Max tool diameter 220 mm Motor power 3 Kw Suction port diameter 100 mm 1° counter-supported profiling spindle: Useful length 600 mm Spindle diameter 50 mm Max tool diameter 220 mm Motor power 7,5 Kw Electronic vertical positioning Electronic horizontal positioning N° 2 suction inlets diameter 150 mm Gusdpfxo Ai Tb Ts Ag Usi 2° counter-supported profiling spindle: Useful length 600 mm Spindle diameter 50 mm Max. tool diameter 220 mm Motor power 7,5 Kw Electronic vertical positioning Electronic horizontal positioning N° 2 suction inlets diameter 150 mm Strip recovery unit: Blade diameter 200 mm Shaft diameter 35 mm Motor power 2,2 Kw Pneumatic vertical positioning Manual horizontal positioning Suction inlet diameter 80 m Profiling table Rubber-tyred roller feed system with electric vertical positioning Safety cabin for the working units both for the tenoning side and the profiling side Electronic control unit: Freely programmable via an alphanumeric keypad, with the option to enter individual programmes, complete work cycles and entire job orders – Electronic tool positioning control with continuous axis, oup to 99 storable positions per axis Vivaldi tool unit Compressed air 7–8 bar Weight 4200 kg

Condition: used, Year of construction: 2010, Working range X = 4,600 mm Y = 1,535 mm Z = 275 mm Designed for heavy-duty applications, making it ideal for machining large solid wood components and structural timber. The 5-axis controlled machining head enables the production of complex three-dimensional workpieces. • Central lubrication system • Desktop PC o Intel Celeron D CPU 2.66 GHz or higher o 512 MB RAM o 40 GB hard drive o 15" LCD monitor o Keyboard o Mouse o CD-ROM drive o Parallel port o RS-232 serial port o USB port o Ethernet card for connection to the office network • Remote service o Direct modem access for remote diagnostics and service • Electrical control cabinet • Air conditioning for the electrical cabinet • Safety system o Two pressure-sensitive safety mats on the front side of the machine with integrated control unit, ensuring safe alternating operation. • Signal lights for alternating (pendulum) machine operation • Job recovery function o Allows machining to resume after an emergency stop. • CE safety protection systems Worktable and accessories • Multizone table for 10 beams and 40 vacuum pods o Allows multiple workpieces to be loaded simultaneously, reducing tool changes and increasing productivity. o Vacuum clamping system o Pneumatic clamping system • 10 ATS beams, each equipped with 4 vacuum pods, L = 1,525 mm • EPS electronically positioned table for 10 beams • Rear stop row for 10 beams with 115 mm travel • Additional stop row at 375 mm with 140 mm travel • Additional stop row at 770 mm with 140 mm travel • Front stop row at 1,175 mm with 140 mm travel • 4 side stops with 140 mm travel (2 left + 2 right) complete with mounting hardware • 2 additional side stops with 140 mm travel (1 left + 1 right) complete with mounting hardware • Position sensors for all stops • 4 lifting devices for easier loading and unloading of workpieces for H = 74 mm modules • Vacuum unit 132 × 146 × H74 mm • Vacuum unit 132 × 75 × H74 mm • Vacuum unit 132 × 54 × H74 mm • UNICLAMP workpiece clamping system • Window manufacturing kit H = 74 mm, 40–98 mm • 6 UNICLAMP double-acting quick-connect clamps • 2 UNICLAMP modules for short workpieces • Chip and waste conveyor • Vacuum generator for 250 m³/h vacuum pump o 250 m³/h vacuum pump • Spindle and machining equipment • Motor power: o 12 kW at 12,000 rpm (S1 duty) o 15 kW at 12,000 rpm (S6 duty) • Maximum spindle speed: 22,000 rpm • Tool interface: HSK F63 • C-axis: continuous 360° • B-axis: ±100° • Coolant unit with 1,600 W cooling capacity • 15-position tool magazine for the 5-axis head • Additional Z carriage for rear units • 8.6 kW PEAK POWER electrospindle with HSK F63 interface and air cooling, specially designed for applications requiring high torque at low spindle speeds • Gear-driven C-axis rotating unit (360°) • BH9 drilling unit o 9 independently controlled drill spindles Godszlz Svjpfx Ag Uoui o Includes: o 5 vertical drills with 32 mm spacing o 2 independent dual-output horizontal drills o Separate 3 kW drive motor • 22-position tool magazine with 180 mm centre distance • Automatic lubrication system Two Leitz tool sets are available for EUR 18,100 + VAT: • LEITZ IV 68 tool set • LEITZ IV 90 tool set This machine is offered for sale on behalf of a customer. Viewing is available by prior arrangement. Please contact us through the platform's messaging system for further information and the relevant technical contact details.

Condition: used, Year of construction: 2001, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, compressed air connection: 6 bar, input current: 204 A, heating capacity: 90 kW (122.37 HP), power: 50 kW (67.98 HP), load capacity: 750 kg, Equipment: documentation/manual, We offer a cleaning and degreasing system, type VAIOCS S G, as a front-loading system (used system from 2002 – completely overhauled* + new cleaning chamber) for batch sizes with a maximum diameter of 1,500 mm and a maximum height of 600 mm, for use with modified alcohol (A III) or hydrocarbons (A III). * Vacuum pump new – all media-carrying pumps new – remaining pumps overhauled – Control cabinet, S7-300 control system, graphic display MP377 and safety technology upgraded to the latest standard – Pneumatics (Festo) serviced and partially new – pneumatic installation completely new – Electrical installation partially new – valve seals new – container insulation new – Refrigeration unit overhauled – Cleaning chamber, basket holder, swivel mechanism and door completely new Manufacturer: EMO Type: VAIOCS SG Order number: 515215 Year of manufacture: 2001 / 2016 Operating voltage: 400 V/N/PE Control voltage: 24 V DC Connected load: 140.0 kW Heating power: 90.0 kW Motor power: 50.0 kW Rated current: 204 A Solvent: Nikutex 2307 Filling volume: 5000 l Gusdpj Ahx Dtefx Ag Uoi If you have any questions or require further information, please feel free to send us a message or call us.

Condition: used, Year of construction: 2020, functionality: fully functional, overall weight: 2,041 kg, total length: 2,300 mm, total width: 1,380 mm, total height: 1,950 mm, power: 75 kW (101.97 HP), volume flow: 851 m³/h, pressure (min.): 5 bar, pressure (max.): 7 bar, ambient temperature (min.): 5 °C, ambient temperature (max.): 40 °C, noise level: 74 dB, protection type (IP code): IP54, Equipment: documentation/manual, refrigerant dryer, type plate available, For sale is a highly efficient, frequency-controlled screw compressor from the top-of-the-line range of the German manufacturer ALMiG, type V-DRIVE 75 (PLUS O version including heat recovery), first purchased at the end of 2020. This unit impresses with minimal energy costs thanks to its loss-free 1:1 direct drive, stepless speed control and integrated heat recovery (WRG). Technical data: Manufacturer: ALMiG Kompressoren GmbH Type: V-DRIVE 75 PLUS O including WRG Drive power: 75 kW Maximum pressure: 7 bar Volume flow: up to 14.18 m³/min (approx. 851 m³/h) Voltage: 400 V / 50 Hz Control system: ALMiG Aircontrol Premium (including RS 485, operating and fault messages) Godpfxe Ahppdo Ag Uoui Dimensions (L x W x H): 2,300 x 1,380 x 1,950 mm Weight: 2,041 kg Equipment & special features: Installation in a special container: - Weather-protected outdoor installation directly on the company premises. - Generous, double-wing access doors for unrestricted maintenance access. - Integrated window with exterior roller shutter. - Standardized container corner fittings (ISO corners) for crane or lifting gear handling are available. - Integrated heat recovery (WRG): For direct use of waste heat for heating purposes or hot water. - Integrated refrigeration dryer (PLUS) & filter system (O): High compressed air quality directly from the compressor. - SCD frequency inverter & asynchronous motor (IP55): Stepless adaptation to demand, soft start without peak loads. - Sound-insulated: Extremely quiet operation thanks to optimized encapsulation and vibration-isolated installation. - Documentation: Complete documentation / manual available. Important sales & collection conditions: - Delivery condition: Sale is ex works (FCA). - Loading: No loading facilities available on site! - The removal must be organized by the buyer using a truck with a loading crane or a separate mobile crane (lifting equipment suitable for ISO container corners required). - The sale is made excluding any liability for defects and warranty. Subject to prior sale and errors.

Condition: used, Automatic filling line for EX-type products, i.e., products filled in a potentially explosive hazard zone 2. These devices are used for products of the following types: - detergents, - cleaning agents, - solvents, - windshield washer fluids, - various types of liquid chemical raw materials, - plasticizers and other process liquids, - fuels and oils, - other liquid petrochemical products – provided that the materials are compatible and the EX design is appropriate. The filling system consists of several components: Guodpfxozu Rqte Ag Usi - ROBAK volumetric filler, type: ANO-750, with Endress+Hauser DOSIMASS flowmeter fillers, EEx standard – this is a Coriolis flowmeter that can directly measure mass flow, as well as density and temperature, and based on this, volumetric flow. - ROBAK single-head capping machine, type: ZR-02, EX standard, currently in a format for 1 L bottles with a safety cap for hazardous products. - ROBAK cap feeder, type: MPZ-03 - Control cabinet Option for filling bottles or canisters. System capacity: 500 - 2,000 bottles per hour. Complete documentation for the machines. Option to order conveyor belts in EX standard. Used machines, regularly serviced.

Condition: used, Powder coating booth with filter cart & fluidized bed For sale is a professional, industrial powder coating system from the traditional manufacturer Gema Volstatic. This is the proven MRS system (Multi-recovery System), which ensures highly efficient powder recovery (overspray extraction) and clean working conditions in the workshop. The system is extremely robust and, thanks to the generous manual coating opening, is ideal for manual operation (hand coating). Technical data & connection values: • Manufacturer: Gema Volstatic AG Gsdpfxez N Aive Ag Ujui • System / Type: MRS booth with filter cart and fluidized bed • Electrical connection: Voltage 3 x 380 V / 50 Hz (standard three-phase) • Compressed air connection (input pressure): min. 6 bar / max. 10 bar (recommended pressure: 7 bar) • Compressed air quality: Water vapor content max. 1.3 g/m³, oil content max. 0.1 ppm • Compressed air consumption (filter plate cleaning): max. 18 Nm³/h • Fan output of the cleaning unit: • For organic powders: Depending on the number of filter plates, from 7.5 kW to 15 kW (volume flow up to 12,000 m³/h) • For powder coating: From 5.5 kW to 11 kW (volume flow up to 8,800 m³/h) • Fan differential pressure: 4.2 kPa (at 8000 m³/h) to 4.5 kPa (at 12000 m³/h) Dimensions & space requirements: • External dimensions of the booth: approx. Length 6.30 m × Width 2.52 m × Height 3.20 m • Internal dimensions of the booth (working area): approx. Length 6.00 m × Width 1.73 m • Dimensions of the platform: approx. Length 7.64 m × Width 2.45 m × Height 1.16 m Equipment & components: • Booth housing: Solid construction including booth inlet and booth substructure • Filter cart with fluidized bed: Excess powder is extracted downwards. The fluidized bed converts the powder into a liquid-like state using compressed air, so that it can be reprocessed and reused in the cycle (enormous material savings!). • Cleaning unit: Unit mounted on top including solenoid valve cover and sealing frame • Safety & control: Integrated pressure monitoring and pneumatic monitoring via the side control unit • Ergonomics: Hand lever valve for easy control directly on the booth, large manual coating opening for the operator, and gun travel slots on the back • CO₂ fire extinguishing system (fire protection system) Item location: 48683 Ahaus / Ottenstein (Münsterland, NRW) Important pick-up & dismantling options (Please note): Option 1: Dismantling by the buyer The system must be professionally dismantled and transported away by the buyer. Option 2: Our "all-inclusive package" (dismantling by us) Alternatively, we will take over the complete, professional dismantling of the system for you. Fixed price for this: €7,500.00 net (plus VAT). "We offer you a suitable bank financing option for your project." You can find more items - new and used - in our shop! International shipping costs on request!

Condition: excellent (used), mileage: 153,000 km, power: 412 kW (560.16 HP), first registration: 08/2013, fuel type: diesel, tire size: 385/65/22.5, axle configuration: 8x2, fuel: diesel, brakes: retarder, color: blue, driver cabin: sleeper cab, gearing type: automatic, emission class: euro5, suspension: steel-air, Equipment: ABS, AdBlue, air conditioning, crane, cruise control, differential lock, electric window regulation, fog lights, parking heater, power mirror, retarder, soot filter, = Additional Options and Accessories = - Aluminum fuel tank - High beam headlights - Speed limiter - Refrigerator - Air suspension - Particulate filter - Sun visor - Auxiliary heater (parking heater) - Toolbox - Power take-off (PTO) - Central lubrication system = Further Information = Axle configuration Brakes: Disc brakes Front axle 1: Tire size: 385/65/22.5; Steered; Suspension: leaf suspension Front axle 2: Tire size: 385/65/22.5; Steered Rear axle 1: Tire size: 295/80/22.5; Twin tires; Differential lock; Suspension: air suspension Rear axle 2: Tire size: 275/70/22.5; Twin tires; Lift axle; Suspension: air suspension Functional Boom: Telescopic (8 sections) Boom length: 21 m Lifting capacity: 12,000 kg Lifting height: 2,300 cm Crane: HIAB 477-8, year of manufacture 2013, mounted behind the cab Superstructure brand: HIAB 477-8 CE marking: yes Condition Technical condition: very good Optical condition: very good SCANIA R560 V8 8X2 TRACTOR UNIT COMBI + HIAB 477 E-8 CRANE EURO 5 L PACKAGE 560 HP DRIVELINE 8X2 REAR LIFT AXLE WHEELBASE 450 CM AIR SUSPENDED Gjdpfxjyiun Hj Ag Uoui CR19H SLEEPER CAB WITH AIR CONDITIONING, PARKING HEATER, AND REFRIGERATOR AUTOMATIC TRANSMISSION TOOLBOX ADJUSTABLE FIFTH WHEEL TOOLBOXES PREPARED FOR BALLAST FLATBED HYDRAULICS FOR TRAILER HIAB 477 E-8 HIPRO CRANE 8X HYDRAULIC EXTENSIONS OIL COOLER FOR CRANE HYDRAULICS LARGE HYDRAULIC WINCH WITH HOOK AND ROLLERS 4X OUTRIGGER SUPPORTS RADIO REMOTE CONTROL MAX LIFTING CAPACITY 12,000 KG MAX LIFTING CAPACITY AT 2080 cm: 1,380 KG WORKING HEIGHT 23.5 METERS FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPAÑOL WE SPEAK ENGLISH

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, rotary table diameter: 450 mm, position of the milling head: Schwenkbar (45°), table diameter: 450 mm, total length: 5,600 mm, gear diameter: 500 mm, total height: 3,100 mm, total width: 3,600 mm, input frequency: 50 Hz, type of input current: three-phase, spindle speed (max.): 340 rpm, table bore: 125 mm, spindle speed (min.): 80 rpm, travel distance X-axis: 325 mm, travel distance Y-axis: 200 mm, travel distance Z-axis: 400 mm, overall weight: 14,800 kg, distance table to spindle center: 350 mm, tool diameter: 200 mm, controller manufacturer: Siemens Sinumerik 840D sl, drive type: Sinamics S120, control type: CNC control, Equipment: documentation/manual, rotational speed infinitely variable, A Pfauter PE 500 for the economical production of straight and helical spur gears up to module 12 and 500 mm in diameter – completely overhauled by SerWeMa with Siemens Sinumerik 840D sl, equipped with a gripper unit and a 32-position workpiece storage for unmanned operation. The machine is ready for operation in our hall in Chemnitz: you can inspect it under power, and if desired, we will mill your own sample part and you can take delivery of the machine here. No delivery time, no risk. Sold by Serwema Retrofit Solutions, the company that carried out the overhaul and knows the machine inside out. The general overhaul included complete geometric overhaul by grinding and scraping, new roller bearings in the main drive and in the milling head, measuring and reconditioning the worm gear, overhauled or new ball screw drives, overhaul of hydraulics, lubrication and coolant system, and new electrical equipment with Sinumerik 840D sl, Sinamics S120 and new axis motors. An electronic generating gear controls all generating and single-part machining processes, and an NC-controlled crash recovery protects the tool and workpiece in the event of a power or phase failure. New paint in RAL 7035/5015 with oil and coolant resistant two-component paint, acceptance of geometry according to SerWeMa protocol based on DIN ISO 6545. The machine controls six CNC axes: X radial, Y tangential, Z axial, A milling head swivel, B milling cutter drive and C table drive. The SerWeMa gear cutting software guides you through workpiece and tool data via masks, without the need for programming: up to three position-oriented gearings per workpiece, each with its own tool, up to three cuts per gearing with simultaneous or counter-rotating movement, form corrections for convex, conical and convex-conical profiles, lead-in and lead-out phase correction, chamfer milling, dimension correction via tooth width, two-roll or two-ball gauge, measuring stop, shift strategy with defect management per generating cutter and cutting force monitoring with automatic retraction. Technologies: generating milling, single-part milling and worm gear milling both radially and tangentially. A hand-held device with a handwheel allows setup directly in the working area. Technical data: max. workpiece Ø 500 mm, max. module 12, max. milling cutter Ø 200 mm, max. milling cutter length 240 mm, shift travel 200 mm, milling cutter speed 100–450 rpm, swivel angle +25°/−45°, travel radial 325 mm (axis distance 25–350 mm), travel axial 400 mm (310–710 mm), table diameter 450 mm, table bore 125 mm, connection power approx. 60 kVA. Installation dimensions incl. automation approx. 7.2 × 4.5 × 3.3 m, weight approx. 16.8 t. Equipment: machine enclosure, chip conveyor, gripper unit with two grippers, workpiece storage with 32 positions, preparation for emission extraction (150 mm nozzle, Harting connector on the machine roof). Documentation complete in German: operating manual, electrical diagrams with parts lists, hydraulic and lubrication diagrams. Gsdsz Et E Eopfx Ag Ueui Serwema optionally offers: trial part milling in our factory, additional milling arbors, assembly and commissioning at your location, operator training and a control system upgrade to Sinumerik ONE. Spare parts and service come from a single source, worldwide, even after the purchase.

Year of construction: 1999, operating hours: 76,000 h, condition: used, functionality: unexamined, Technical parameters: • Manufacturer: AUSTRIAN ENERGY • Type: Dual pressure drum boiler (1999) • HP steam flow: t/h 40.8 • LP steam flow: t/h 17.3 • HP steam parameters: bar/°C 52 / 425 • LP steam parameters: bar/°C 4.2 / 180 • Flue gas temperature at HRSG outlet: °C 80 • Flue gas stream to the stack: t/h 468, k Nm3/h 482 • Heat recovered by the steam and water cycle from flue gas in HRSG: MWt 45.9 • Maximum output of DH exchanger: MWt 8.0 • Operating hours: 76,000 hours The high- and low-pressure sections of the equipment and the drums (HP and LP) consist of 6 independent, transportable modules. The boiler wall insulation is partial and requires replacement. Guedpfx Agey D Hy Es Uji

Condition: used, Powder coating booth with multi-cyclone and after-filter Gsdpfx Aoz Nyqweg Ujui For sale is a professional, complete industrial system for powder coating: A Gema Volstatic powder coating booth, type MRS (multi-cyclone recovery system with after-filter). This system represents the highest Swiss quality, extreme robustness, and maximum efficiency in powder recovery. Thanks to its generous dimensions, it offers plenty of space for long and bulky workpieces. It is ideal for industrial companies, powder coaters, or workshops looking for a powerful and reliable system. Technical data • Manufacturer: Gema Volstatic • Type: MRS (multi-cyclone and after-filter system) • Electrical connection: 3 x 380 V / 50 Hz • Equipment: Booth substructure with inlet, manual coating opening, and spray gun travel slots. • Recovery: Highly efficient multi-cyclone with cleaning flap and powder collection container. • Extraction / After-filter: Powerful fan unit with integrated pressure monitoring and automatic flushing air filter cleaning. • Fan power after-filter: 15 kW with 12 filter plates (air volume flow: 8000 m³/h) 22 kW with 16 filter plates (air volume flow: 12000 m³/h) • Fan differential pressure: 4.2 kPa (at 8000 m³/h) or 4.5 kPa (at 12000 m³/h) • Compressed air connection: Min. 6 bar / Max. 10 bar (Recommended: 7 bar) • Compressed air consumption (flushing air filter box): Max. 18 Nm³/h • External dimensions: approx. Height 3.20 m × Length 8.50 m × Width 1.84 m • Internal dimensions (usable space): approx. Height 2.40 m × Width 1.84 m Item location: • 48683 Ahaus / Ottenstein (Münsterland, North Rhine-Westphalia) Important pick-up & dismantling options (Please note): Option 1: Dismantling by the buyer The system must be professionally dismantled and transported by the buyer. Option 2: Our "all-inclusive package" (dismantling by us) Alternatively, we will take over the complete, professional dismantling of the system for you. Fixed price for this: 7,500,- € net (plus VAT). "Everything from one source: We would be happy to offer you a suitable bank financing option for your project." More items - new and used - can be found in our shop! International shipping costs on request!

Condition: ready for operation (used), Year of construction: 2020, operating hours: 1 h, load capacity: 45 kg, arm reach: 2,050 mm, number of axes: 6, This 6-axis ABB IRB 4600-45/2.05 robot arm was manufactured in 2020. It features a load capacity of 45 kg and a reach of 2.05 m, making it suitable for various automation tasks. The robot is equipped with a Single Cabinet Controller (IRC5) and includes advanced safety features. If you are looking to get high-quality automation capabilities, consider the ABB IRB 4600-45/2.05 robot arm we have for sale. Contact us for further details. - Payload: 45 kg- Reach: 2.05 m- Number of Axes: 6- Protection Rating: Standard- Color: ABB Graphite White std (209-202)- Manipulator Net Weight: 425 kg- Controller Net Weight: 150 kg- Operating Voltage: 3x 400 V AC, 50-60 Hz- Rated Current: 13 A- Short-Circuit Rating: 10 kA- Main Connection: Connector HAN HSB 6p+E (752-2)- Main Switch: Rotary switch (742-1)- Service Socket: 230 V (736-1)- Operating Ambient Temperature: Up to max. 45 °C (708-1)- Manipulator Cable Length: 7 m (210-2)- Teach Pendant: FlexPendant with 10 m connection cable (701-1)- Operating System / Firmware: RobotWare 6 (Boot Application 6.10.02.00) Software Options Installed: * 888-2 ProfiNet I/O Master/Slave Software * 996-1 Safety Module * 997-1 PROFIsafe F-Device * 1125-2 SafeMove Pro * 608-1 World Zones * 611-1 Path Recovery * 616-1 PC Interface * 617-1 FlexPendant Interface * 623-1 Multitasking * 689-1 External Guided Motion * 824-1 MultiFunction * 641-1 RobotWare Dispense- Interfaces & I/O Modules: * 803-2 User interface (parallel, EtherNet, and air) * 431-1 Mating connector for customer signal interface * 239-1 Mating connector kit at robot base * 970-1 RS232 serial interface * 1541-1 Digital I/O base module (16 In / 16 Out) * 731-1 Internal safety signals- Included Base Plates & Mounting Sets: * Base plate Type A (IRB2600/4600) height H=60 mm * Robot mounting kit for IRB4600 * Fastening kit GP Type C + SO Type C+G- Calibration Offset Data (Axis Resolver Values): * Axis 1: 3.9506 * Axis 2: 5.4462 * Axis 3: 5.6400 * Axis 4: 0.5636 * Axis 5: 1.2936 * Axis 6: 2.8601 Gjdpe Agwzkjfx Ag Ueui

Condition: ready for operation (used), Year of construction: 2008, operating hours: 116,131 h, functionality: fully functional, SIEMENS SGT-300 (TEMPEST) industrial Combined Heat and Power (CHP) / Poligeneration Plant, originally installed in 2008 and designed for continuous industrial operation. The plant is based on a Siemens SGT-300 single-shaft gas turbine with Dry Low Emission (DLE) combustion technology and a complete Waste Heat Recovery System (WHRS/HRSG) capable of simultaneously producing electrical power, process steam, thermal oil and chilled water. Gas Turbine • Manufacturer: Siemens • Model: SGT-300 (TEMPEST) • Year: 2008 • Type: Industrial Single Shaft Gas Turbine • Fuel: Natural Gas • Dry Low Emission (DLE) combustion Guodpfx Agozmga Io Usi • ISO Electrical Output: 7.9 MW • Site Output: approx. 7.6 MW • Generator Voltage: 6.3 kV • Frequency: 50 Hz • Generator Speed: 1,500 rpm • Electrical Efficiency: approx. 30.5% • Exhaust Gas Flow: 30.2 kg/s • Exhaust Gas Temperature: 545°C • Continuous duty (24/7 operation)Complete heat recovery package including: ✔ Thermal Oil Heater – DOWNTHERM A – 4.3 MW ✔ Thermal Oil Heater – SANTOTHERM 66 – 3.88 MW ✔ High Pressure Steam Generator (25–26 bar) ✔ Low Pressure Steam Generator (4.5 bar) ✔ Hot Water Generator Cooling capacity: 1.7 MW Production of: • Electricity • High pressure steam • Low pressure steam • Thermal oil • Hot water • Chilled waterOperating hours: 116,131 h, according to control panel Starts: 677, according to control panel Location: Spain Documentation: Available upon request Inspection: By appointment

Condition: excellent (used), Year of construction: 2010, KOMORI LITHRONE S-529 M C 66 million Year: 2010 Max. sheet size: 530 x 750 mm Max. print area: 520 x 736 mm Min. sheet size: 200 x 360 mm Substrate thickness range: 0.04 – 0.8 mm Max. production speed: 16,000 sheets/h *PQC-S remote control system (Quality Control System) for printing ▪️Remote ink control ▪️Remote dampening control ▪️Remote register control *KHS-AI® computer-controlled machine management system ▪️Intelligent inking system ▪️Machine self-diagnostic function ▪️Advanced CIP4-based information flow management ▪️Module for connection to a scanning unit * Touchscreen monitoring * High-Speed-Start system * Densitometric scanning unit * Automatic blanket cylinder washing * Automatic inking unit washing (dual nozzles for solvents and water) * Automatic impression cylinder washing * Remote substrate thickness adjustment from the control console * Remote substrate format adjustment from the control console * Semi-APC (Semi-Automatic Plate Change) system * Stream feeder with an 800 mm pile height * Feeder head equipped with lifting suckers (2x) and forwarding suckers (2x) * Deionizing air blast at the feeder head * Side air blasts * Pile support table for manual pile preparation * Table • Stream feeder with additional suction tapes * Electronic feed control * Electronic front-lay (register mark) control * Skew control via front-lay bar * Optoelectronic sheet-flow monitoring from the feed pile * Ultrasonic double-sheet detection (ULTRASONIC) * High-precision impression cylinders * Reduced number of transfer cylinders * Solid-construction transfer cylinders * Accessible plate cylinder * Accessible blanket cylinder * Chrome-plated impression cylinder * Cylinder designed for high-load/heavy-duty applications * Diamond-coated transfer grippers * Precision ink-feed adjustment (500-step ink-fountain key opening) * Inking unit featuring 19 rollers, including 4 oscillating/distributing rollers * Anti-ghosting roller (B and D positions) * Independent drive for the ink-fountain roller (ductor) * Adjustable ductor dwell time * Remote control of ink zones via the PQC-S console Gsdpfx Ago Ah Sbxs Ujui * Option to disengage the inking unit on the first or fifth printing unit KOMORIMATIC Dampening System * Dampening system suitable for both alcohol-based and alcohol-free printing * Oscillating roller for uniform dampening solution distribution, preventing ghosting and streaking * Rotational speed reduction • Continuous cleaning of the printing cylinder (or flat cylinder surface) based on the type of soiling * Integrated sensor * Pneumatic engagement and disengagement of rollers, controlled from the operator console * High-pile delivery (stack height: 900 mm) * Sheet decurler * Deionizing bar * Automatic lubrication for delivery chains * GRAFIX powder spray system o Automatic adjustment for printing speed o Automatic format compensation * Engagement and disengagement of dampening rollers * Engagement and disengagement of inking rollers Coating unit with TRESU chambered doctor blade system o Suitable for water-based and UV coatings o Remote register adjustment: ▪️ Lateral ▪️ Circumferential ▪️ Diagonal (adjusted at the transfer cylinder) o Remote adjustment for substrate thickness o Extended delivery: 2,000 mm o Special gripper bars – shadow-free (prepared for the installation of UV dryers) o Designed for tool-free mounting of rubber or photopolymer plates * Chambered doctor blade system

Condition: used, Year of construction: 2024, MACHINE PROFILE: 3,800 kN (420 US tons) IMM ===== Machine ID: • Injection Unit: 265 • Clamping Unit: 380 • Weight: 21,300 kg Clamping Unit Specifications: • Force: 3800 kN (388 tons / 420 US tons) • Tie-bar Spacing: 830x830 mm • Platen Size: 1190x1190 mm • Stroke (Open/Eject): 700 / 210 mm • Ejector Force: 90 kN • Mold Height (Min/Max): 300 / 750 mm (+800 option) • Max Mold Weight: 3.8 tons Gedpfozzv Tgex Ag Ujui • Dry Cycle: 2.3s / 500mm Injection Unit Specifications (By Screw: 25 / 30 / 35 mm): • L/D Ratio: 24 / 24 / 20 • Capacity: 74 / 106 / 144 cm³ • Rate: 98 / 141 / 192 cm³/s • Recovery Rate: 10 / 15 / 22 g/s • Pressure: 2700 / 2700 / 2000 bar • Stroke / Speed: 150 mm / 420 rpm • Nozzle (Stroke/Force): 305 mm / 40 kN • Heating Capacity: 9.2 kW