Used High Dryer for sale (21,963)

Condition: ready for operation (used), Year of construction: 2007, functionality: unexamined, machine/vehicle number: 070079A, total height: 4,500 mm, total length: 5,400 mm, total width: 5,500 mm, pressure: 6 bar, control cabinet height: 2,000 mm, control cabinet length: 2,500 mm, control cabinet width: 500 mm, operating temperature: 25 °C, working height: 950 mm, heating capacity: 107 kW (145.48 HP), number of seats: 66, workpiece length (max.): 3,200 mm, workpiece width (max.): 1,350 mm, workpiece height (max.): 80 mm, Equipment: documentation/manual, emergency stop, Giardina drying oven, manufactured in 2007 Codpfszcnu Hox Agrjhd with three different climate zones: evaporation zone - heating zone - drying zone Mobile pallets with conveyors, therefore no minimum size requirement for components Continuous vertical conveyor system

Condition: like new (used), Year of construction: 2021, Kaeser Secotec TE 142 Refrigeration Dryer YOM 2021 Serial number: 149-8393351 16 Bar 3-60 degrees C Refrigerant R513A Flow rate: 14.50 m3/min - 14500 l/min Total width: 712 mm Total length: 982 mm Total height: 1,612 mm Overall weight: 249 kg Kaeser compressed air dryers ensure dry, optimal compressed air for all flow rates. Built as high-quality industrial machines, they reliably protect your system and processes from condensation damage, even under extreme conditions. Chodpfeyy U I Njx Agrjd

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, total length: 69,000 mm, total width: 16,000 mm, total height: 16,000 mm, The system was designed and dimensioned according to Eurocode EN 1993 for the industrial drying of wood chips, sawdust, or similar biomass products and is suitable for use in biomass, wood, or pellet production. Process components: Air heater, deflection rollers, feeding modules, discharge modules, trough chain conveyor, belt tensioning and adjustment device, 7 exhaust stacks (height up to approx. 17.6 m) Designed for hot air or waste heat utilization (e.g., biomass boiler or CHP plant), heat requirement 10,270 kW thermal, installed electrical power 690 kW electrical. The inlet temperature in the dryer is 68°C, the outlet temperature is 42°C, and the heat transfer medium is a water/glycol mixture. The volume flow rate at the dryer outlet is 1,081,000 m³/h. Dust emission value 5 mg/Nm³ (moist), sound pressure at a distance of 1 m 85 dB(A) from the outlet of the discharge duct and the dryer. The dryer is designed for an ambient temperature of up to -40°C; the conveying capacity is at least 70 m³/h and a maximum of 250 m³/h with a bulk density of 260 kg/m³. The furnace is NOT included in the offer; we only sell the belt dryer! The working level of the dryer is supported by steel columns approximately 8.00 m high and is enclosed with thermally insulating sandwich panels. A hall or other production components can be placed under and between the columns (see documents, steel structure). The system has been disassembled and stored by an experienced assembly team; this team can be arranged for transport and reassembly. Chjdpozw Apgsfx Agred Please note: We only sell this belt dryer without a furnace and no other parts! Please send your inquiries via WhatsApp to Mr. Sörgel; he is on-site at the factory and may not always be available by phone. Thank you very much!

Year of construction: 2019, condition: like new (used), TM Norway Automatic Gas Cylinder Filling Carousel 200/300 bar For sale: professional, fully automatic gas cylinder filling carousel manufactured by TM Norway AS, Norway. Year: 2019 Project / Serial No.: PRJ-2018-02-13-0001 CE marked This system is designed for the automated handling, preparation, filling, and control of high-pressure gas cylinders. It is suitable for industrial gas producers, cylinder filling plants, technical gas suppliers, welding gas companies, specialty gas producers, and other professional gas filling facilities. Main features: * Fully automatic 8-station carousel concept * Cylinder sizes approx. 5-50 liters according to TM Norway platform specifications * Designed for 200 and 300 bar applications * Suitable for single gases and gas mixtures * Automatic cylinder positioning and handling * Automatic valve orientation and adapter connection, depending on the configuration * Residual-pressure measurement * Automatic blow-down * Vacuum preparation * Automatic gas filling * Final pressure measurement * Automatic valve closing * Leak testing * Automatic adapter disconnection * Industrial PLC/HMI control * Rexroth control equipment * Siemens SIMATIC mobile panel * TROAX safety guarding with interlocks and emergency stops Chsdpfo Ahhttox Agrsd Possible gas applications, depending on the installed gas supply, adapters, software, and certification: Oxygen (O2), Nitrogen (N2), Argon (Ar), Carbon Dioxide (CO2), Helium (He), welding gases, shielding gases, industrial gases, technical gases, specialty gases, and mixed gases. The TM Norway carousel platform can support different cylinder valve connections, including DS, BS, DIN, AFNOR, CGA, and VIPR/integrated valves, depending on the installed adapters. This is not a simple manual filling manifold. It is an automated industrial cylinder filling system intended to automate several operations normally performed manually in a gas filling plant. Ideal for: Industrial gas plants, gas bottling plants, cylinder filling centers, oxygen filling plants, nitrogen filling plants, argon filling plants, CO2 filling plants, welding gas producers, mixed-gas plants, and gas plant integrators. Used industrial machine. The installation is available for inspection. The exact gas configuration, adapters, software, operating pressure, scope of supply, and recommissioning requirements must be verified for the buyer's intended application. Detailed technical PDF available upon request. Keywords: automatic gas filling carousel, gas cylinder filling machine, cylinder filling system, gas bottling plant, high-pressure gas filling, 200 bar, 300 bar, oxygen filling, nitrogen filling, argon filling, CO2 filling, helium filling, mixed gas filling, welding gas filling, industrial gas equipment, cylinder filling automation, TM Norway gas filling system. Kosan Crisplant gas filling, Kosan gas filling carousel, Siraga filling carousel, Pamasol filling machine, Pamasol gas filling, Rotarex gas filling system, Cryostar gas equipment, Linde gas filling equipment, AGA gas filling system, Messer gas filling plant, Air Liquide gas filling equipment, Air Products gas filling equipment, gas filling carousel alternative, automated cylinder filling alternative, industrial gas carousel, automatic cylinder filling carousel, high-pressure gas carousel, gas bottle filling carousel, gas bottle filling machine, compressed gas bottling machine, industrial cylinder filling equipment.

Condition: used, Little used European Spraydry Technologies model 8 - 19 Tall Form Spray 304 stainless steel ATEX rated spray dryer system. Mass balance design capabilities approximately 246kgs feed @ 10% solids with 26kgs Powder @ 5% residual moisture + 220kg/h water evaporated based on Potato Proteins. Inlet temperature 190 deg.c. with exhaust temperature 90 deg.c. Mass flowrate of drying air rated 6,895kg/hr. System includes the following parts: (1) Airco model CHP inlet fan driven by 11kw motor. (1) Lanemark model DB07 propane burner with control panel. (1) Tall form spray dryer chamber with conical base fitted with dislodging hammers fitted to cylinder and cone. Access/inspection doors. Explosion suppression bottles. (1) Stainless steel feed lance with pressure nozzle. (1) 304 Stainless steel product cyclone with explosion suppression bottles. Includes DMN Westinghouse type AL250DairyMZC-11 APS rotary lock value with motor. (1) Exhaust air chamber with explosion suppression bottle. (1) Gough type GBS550 stainless steel vibratory sifter/screen, mounted on stainless steel mobile frame. (1) Feed balance stainless steel vertical vessel. (1) FBF Italia model FBF2004/P High pressure plunger pump. (1) Mettler Toledo type V4-REM industrial flow-though metal detector with Piab conveying system. (1) Airco type CHP825 exhaust fan driven by 30kw motor. (1) Robbe model Atlas filling machine for bags with controls. Cedjz D Efnepfx Agrohd Various small scale circulation pumps, pipework, instrumentation and ducting available. System has now been removed from installed production position and ready for loading Specifications: Material Of Construction: 304 Stainless Steel Type Of Spray: Nozzle

Condition: used, Used compressed air refrigeration dryer MTA DE225 for drying compressed air in industrial compressed air systems. Manufacturer: MTA S.p.A. Type: DE225 Csdpe Ahyx Uofx Agrohd Year of manufacture: 2006 Serial number: 2200091067 Voltage: 400 V Phases: 3 Frequency: 50 Hz Installed power: 6.0 kW Maximum current draw: 11.0 A Protection class: IP22 Refrigerant: R134a Refrigerant charge: 4.72 kg Maximum permissible refrigerant pressure, low-pressure side: 22.6 bar Maximum permissible refrigerant pressure, high-pressure side: 26.0 bar Maximum operating pressure, compressed air: 16 bar Maximum operating temperature, compressed air: 70 °C Ambient temperature: +5 to +50 °C Sound pressure level: < 70 dB(A) Weight: 610 kg Refrigeration compressor: Maneurop MTZ80HP4A Control: Electronic with display Condition: Used

Condition: new, Year of construction: 2026, power: 11 kW (14.96 HP), Rotary drum dryer for drying various kinds of materials like sand, biomass, sawdust, red mud, bentonite, coal Diameter: 1200mm Length: 10000mm Power: 11-13KW Gradient: 3% Capacity: 1.5-3 t/h Weight: 14Tons Besides this model, we also have the other models of rotary drum dryer 1500x12000mm, 2400x20000mm, and complete drying system for various materials, welcome to contact us for more details Our factory can design suitable solution according to your specific requirements. Rotary drum dryers are highly efficient machines used extensively in the processing of wood chips, sawdust, and biomass. They operate by utilizing a rotating drum that heats and dries the materials as they are transported through the cylinder. The design of these dryers allows them to handle a wide range of particle sizes and moisture levels, making them suitable for various types of biomass. They can also tolerate high-temperature exhaust gases, which contributes to their efficiency and versatility in industrial applications. Rotary Drum Dryer for Wood Chip, Sawdust, Biomass 🌳 Introduction to Rotary Drum Dryers In the realm of biomass processing, moisture control is key. Enter the Rotary Drum Dryer, an indispensable machine designed to efficiently reduce the moisture content of wood chips, sawdust, and biomass. This essential tool enhances productivity, improves fuel quality, and is pivotal in biomass energy production. Let’s explore its functionality and benefits! 💡 💼 Key Benefits of Using a Rotary Drum Dryer 1. Energy Efficiency: Designed to optimize energy use, Rotary Drum Dryers consume less power while delivering high drying efficiency. 🌿💡 2. High Capacity: Capable of handling large volumes of biomass, these dryers are perfect for industrial applications where large-scale drying is needed. 🏭 3. Improved Product Quality: By achieving the optimal moisture content, the dryer enhances the quality of biomass for fuel, pellets, and other applications. 🔥 4. Versatility: Suitable for a wide range of materials including wood chips, sawdust, and various types of biomass, making it a versatile tool in any biomass processing plant. 🌳 # Application Fields and Materials of Rotary Drum Dryer II. Application Fields A. Agriculture - Drying of grains, seeds, and forage. - Processing of agricultural by-products like straw and husks. B. Food Industry - Dehydration of food products such as fruits, vegetables, and spices. - Preservation of food quality during drying. C. Chemical Industry - Drying of chemical powders, granules, and crystals. - Application in the production of fertilizers and detergents. D. Mining and Minerals - Drying of ores, coal, and mineral concentrates. - Reduction of moisture content for easier handling and processing. E. Construction Materials - Drying of sand, cement, and other construction aggregates. - Preparation of materials for manufacturing processes. F. Pharmaceuticals - Drying of pharmaceutical powders and active ingredients. III. Materials Processed by Rotary Drum Dryer A. Organic Materials - Biomass, wood chips, sawdust, and animal feed. B. Inorganic Materials - Sand, clay, limestone, and gypsum. C. Waste Products Cedpfoq Igyvjx Agrohd - Sludge from wastewater treatment plants. - Industrial by-products for recycling or reuse.

Condition: new, Year of construction: 2018, operating hours: 2 h, SJ 1 2 0 X 3 8 h i g h e f f i c i e n c y single screw extruder with auto feeder and dryer SJ 30X25 Mark line extruder The head, mold and calibrator ( 710 1 2 00 mm Front vacuum fix Chodpfxjqmn Ibo Agrjd ing tank 1.5m Back vacuum fixing tank 10.5m Spraying cooling water tank 6m Oval adjusting equipment QJ 1 20 0 Haul off machine ten tracks) QG 1 2 00 Chipless cutter Pipe s tacker

Condition: like new (used), Year of construction: 2012, Atlas Copco CD 70+ adsorption dehumidifier YOM 2012 Capacity: 4,200 l / min Pressure dew point: -40 ° C Chodjyzaamepfx Agred Pressure drop: 0.16 bar Maximum operating pressure: 14.5 bar Filter sizes: DD / PD 60 - DDp 60 Weight: 120 kg Dimensions: 550 (L) × 364 (W) × 1479 (H) mm inlet air temperature: 35 ° C ambient temperature: 25 ° C operating pressure: 7 bar

Condition: good (used), Year of construction: 2021, REF: MM6468 Codpezn Rbfjfx Agrjhd 1 x MKN FlexiChef 150L high-performance multifunctional cooking pan. Suitable for soups, stews, ready meals, meat, fish, rice and pasta, bakery and confectionery products. Manufacturer - MKN Maschinenfabrik Kurt Neubauer GmbH & Co KG. Type - FCEKMP133DR-G20037. Serial number – 21542551. Date of manufacture – 2021. Electrical requirements - 380-415 V / 50 hz / 3 phase. Power - 34 kW. Water pressure - 200-600 kPa. Overall dimensions - 1600mm long x 910mm wide x 1020mm high. Machine weight - 390 kg.

Year of construction: 2021, condition: like new (used), machine/vehicle number: 100056463, This is a miniature Buchi B-290 spray dryer (Mini Spray), a high-quality piece of equipment suitable for various laboratory processes. It is a reliable and efficient tool for your laboratory experiments. This device is designed to provide consistent and accurate results with each use. Thanks to its excellent features, this spray dryer is ideal for the medical sector, laboratories, health equipment and devices, the dental field, as well as industrial applications. Chedpfx Ags Ah Eh Dersd It is a BUCHI brand, model B-290 Mini Spray Dryer, serial number 100056463, year 2021, and this equipment is NEW. Take advantage of this opportunity to acquire this exceptional tool and benefit from its practicality and performance. Year-end clearance sale.

Condition: new, Year of construction: 2026, functionality: fully functional, power: 11 kW (14.96 HP), A triple pass rotary drum dryer is a type of industrial dryer that is used to reduce or remove moisture from a material. It gets its name from the three rotating drums through which the material passes, each with a different purpose in the drying process. This type of dryer is commonly used in the production of various bulk solids, including minerals, agricultural products, and biomass. Here are the key features and components of a triple pass rotary drum dryer: 1. Triple Pass Design: - The material being dried passes through three rotating drums or cylinders, hence the term "triple pass." Each drum serves a specific purpose in the drying process. 2. Material Flow: - The material enters the dryer and first passes through the innermost drum. After the initial drying phase, it moves to the middle drum and then to the outer drum, undergoing additional drying in each pass. 3. Heat Source: - Heat is typically provided by a combustion system, such as a burner or furnace, located at one end of the drum dryer. The hot gases generated by the combustion process flow through the rotating drums, transferring heat to the material. Chedpfx Ajq Nfuzjgrsd 4. Air Flow: - The dryer is designed to optimize air flow through the drums, ensuring efficient drying. In a triple pass design, the material and hot gases move counter-currently through the three drums, enhancing heat transfer and drying efficiency. 5. Lifting Flights or Lifters: - Lifters are internal components inside the drums designed to lift and cascade the material as it rotates. This movement promotes good heat transfer and uniform drying. 6. Retention Time: - The triple pass configuration allows for an extended retention time of the material in the drying system. This longer exposure to heat enhances the drying efficiency, making the triple pass rotary drum dryer suitable for materials with high moisture content. 7. Cooling Section: - After the material completes the three passes and reaches the end of the drum dryer, a cooling section may be included to reduce the temperature of the dried material before it is discharged. 8. Applications: - Triple pass rotary drum dryers are used in various industries, including agriculture (drying crops like grains), minerals (drying ores or concentrates), and biomass (drying wood chips or other organic materials). 9. Efficiency and Energy Consumption: - Triple pass rotary drum dryers are known for their high efficiency due to the extended drying time and effective heat transfer. However, they may have higher energy consumption compared to single or double pass dryers. When selecting a triple pass rotary drum dryer, it's essential to consider factors such as the type of material to be dried, required moisture reduction, and overall processing requirements. Proper design and operation are crucial to achieving optimal drying performance. Technical details We have different options for different requirements, please contact our team for more info.

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, Timber drying 3 chamber ensemble (fully functioning, used). Parameters: - length: 12,9 m - width: 8,8 m - total height: 5,2 m / usable height: 4,1 m Chsdpfezg Iw Iex Agrod Hot water 90°C More technical details available on demand. On site inspection and testing are possible.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, We are offering this very well-maintained machine for the production of paper cups (8oz), manufactured in 2017. Machine designation: Paper Cup Machine (8oz) Manufacturer: DAE SUNG HIGH TECH CO., LTD. Model: DSD-60A Serial number: 17-DS-0027_INTERPACK Year of manufacture: 2017 Condition: very good (used) Functionality: fully functional Dismantling and transport must be organized by the buyer at their own expense. Cjdpfoziau Djx Agrjhd If you have any questions or require further information, please feel free to send us a message or call us.

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, We are offering this very well-maintained machine for the production of paper cups (12 oz), manufactured in 2018. Machine designation: Paper Cup Machine (12 oz) Manufacturer: DAE SUNG HIGH TECH CO., LTD. (Country: Korea) Model: DSD-60A Serial number: 18-DS-0045 Year of manufacture: 2018 Condition: very good (used) Functionality: fully functional Dismantling and transport must be organized by the buyer at their own expense. If you have any questions or require further information, please do not hesitate to contact us. Chjdpfozia U Djx Agrjd

Condition: used, functionality: fully functional, With this offer, you are purchasing a second-hand “Canon High Capacity Stacker H1/J1” finishing machine Item for sale: 1 x Canon High Capacity Stacker H1/J1 Condition: This offer is for a second-hand machine, which may show signs of wear (minor scratches or discolouration). Cedpfxsz Ixzqj Agrohd Compatible with various Canon imagePRESS models, including the C650/C750/C850, C710/C810/C910 and C8000VP/C10000VP. The device has been tested to ensure it is in working order Packaging and dispatch: You are welcome to view the device during our opening hours. Please arrange an appointment to do so! Sturdy packaging and worldwide dispatch available on request! A functional test will be recorded on video for you prior to dispatch or collection. For further information, please feel free to contact us directly.

Condition: like new (used), Year of construction: 2025, High Lift Electric Pallet Truck ( As NEW) Year 2025 Pharma specifications 800mm Lift Fully stainless steel Chedpoz I S Eijfx Agrod Fork length 1150mm Lift capacity 1000kg Compact battery pack, folds up inside the truck, no possibility of damage Complete with charger CE certified Quantity six in stock

Condition: used, Year of construction: 2018, The Airtec ATC 7.5 Screw compressor and air dryer Heavy-duty industrial compressor. Specifications Year 2018 Cedpszf Ivuefx Agrohd Motor Power: 7.5 KW (10HP) Maximum Pressure: 8 bar Free air delivery 1.1 m3/min Tank Capacity Options: 500 Litres Power Requirements: 3-Phase Electric Pump Type: Belt-driven, cast-iron piston

Condition: excellent (used), For sale: timber drying kiln with 3 plus 3 chambers. In very good condition. Chjdpfx Agoy R Tdwjred

Condition: excellent (used), Year of construction: 2026, operating hours: 1 h, functionality: fully functional, machine/vehicle number: F210198, compressed air connection: 6 bar, warranty duration: 12 months, year of last overhaul: 2026, Equipment: documentation/manual, F2000 HS - HIGH SPEED AUTOMATIC CARTON ERECTOR CARTON DIMENSIONS: - Length: min. 220 mm - max. 600 mm - Width: min. 100 mm - max. 500 mm - Height: min. 100 mm - max. 500 mm TECHNICAL DATA: - Siemens S71200 PLC control - Performance: 1200 cartons/min (depending on length and quality of the cartons) - Motorized carton magazine: 120 cartons - Control panel: HMI digital, Kite model 7'' - Automatic start/stop via photoelectric sensor - Venturi vacuum system: 25 m3/h, 700 mm HG - Mains voltage 400V, 3-phase, N, PE - 50/60 Hertz - Protection class IP 54 - Compressed air 6 bar - Air consumption 22 nl - Operating environment +5° C - max. +35° C - Working height 650 mm, adjustable +30 mm - Weight 1,160 kg - Dimensions of the erector incl. sealer in mm (l x w x h): 3,200 x 2,580 x 1,990 - CE safety protection The system includes a GEM B52HS carton sealer. GEM B52HS CARTON SEALER WITH SIDE DRIVE BELTS FOR CONSISTENT CARTON FORMAT CARTON DIMENSIONS: - Length: min. 150 mm - max. ∞ mm - Width: min. 150 mm - max. 670 mm - Height: min. 100 mm - max. 670 mm TECHNICAL DATA: Csdpfx Agsz Dwz Ijrshd - Drive and guide belts, vertical - Carton format adjustment, manual - Sealing unit, bottom - Standard version T22 / T23 - Adhesive tape width: 38 to 50 mm, depending on the unit - Tension adjustable - Max. adhesive roll diameter: 360 mm - Adhesive tape roll core: 76 mm - Mains voltage 400V, 3-phase, N, PE - 50/60 Hertz - Consumption 0.25 kW - Protection class IP 54 - Operating environment +5° C - max. +35° C - Transport speed 22 m/min - Average production 1000 cartons/hour - Working height 650 mm - Weight 120 kg - Dimensions of the erector incl. sealer in mm (l x w x h): 3,200 x 2,580 x 1,990 - CE safety protection: side sheet metal covers with access door, upper and lower covers (mandatory when combined with F1000/F2000/F2008) The image may contain optional features that incur an additional cost.

Condition: good (used), Year of construction: 2006, operating hours: 9,911 h, functionality: fully functional, travel distance X-axis: 450 mm, travel distance Y-axis: 270 mm, travel distance Z-axis: 310 mm, rapid traverse X-axis: 75 m/min, rapid traverse Y-axis: 75 m/min, rapid traverse Z-axis: 75 m/min, nominal power (apparent): 17 kVA, total height: 2,300 mm, total length: 1,500 mm, total width: 2,600 mm, overall weight: 3,400 kg, spindle speed (max.): 30,000 rpm, spindle nose: HSK40, number of slots in tool magazine: 40, input voltage: 400 V, Equipment: documentation/manual, CNC machining center CHIRON FZ08 KS Magnum High Speed Plus (HSP) TECHNICAL CHARACTERISTICS: Year of manufacturing: 2006 CNC control : FANUC 18i-MB5 Number of axes : 7 Stroke X axis : 450 [mm] Stroke Y axis : 270 [mm] Chsdpfxe Ahg I Ee Agrod Stroke Z axis : 310 [mm] Traversing feeds X, Y and Z axes : 75000 [mm/min] Max. bar diameter in turning spindle : 32 [mm] Main spindle max. speed : 8000 [rpm] Main spindle max. power : 12 [kW] Angular A axis stroke : 360 [°] A axis indexing precision : 0.001 [°] B axis swivelling stroke : -20° / +115 [°] B axis indexing precision : 0.001 [°] Spindle type : HSK40 Max. spindle speed : 30000 [rpm] Tool changer magazin number of stations : 40 Part turnaround by robot (6th side machining) : Yes RS232 Interface : Yes Total power required : 17 [kVA] Supply voltage : 400 [V] Number of running hours : 9911 [h] Dimensions : 1500 x 2600 x 2300 [mm] Weight : 3400 [Kg] EQUIPMENT INCLUDED: x1 RENISHAW TS27R tool probe x1 spindle cooling unit x1 parts catcher x1 coolant tank x1 unit for 6th face machining (gripping system not included) x29 tool holders type HSK40 BIG KAISER x10 collets type F37 SCHAUBLIN x1 washing gun x1 3-color status light x1 maintenance manual x1 electrical diagrams manual x1 operator's manual x1 programming manual Price on request, loading on truck included. Possibility of shipping Worldwide. The information on this page has been obtained by the best of our ability. Therefore, its accuracy can not be guaranteed Machine similar to brands such as Okamoto, ELB, GER, Tacchella, Karstens, Jones & Shipman, Jung, Favretto, Blohm. Internal and external grinding (ID/OD) also to be considered. Surface grinder, lathe, machining center, milling machine.

Condition: used, Scott AST Air Swept Tubular Dryer Chedpfxszvgiuj Agrod Flash Drying of Filter Cakes, Powders and Granules. Model 5418 Dryer complete with feeder, air heater and exhaust fan. 110 kW vee-belt drive Feed Screw with agitated feed hopper. 3.4 MW LPG fired air heater with combustion chamber. Adjustable paddles to control retention time. Large access doors for ease of cleaning. Exhaust fan with 90 kW vee-belt drive. Airflow : 30,000 m3/hour Equipment is offered in "as is" condition with no warranty given or implied. PPDS can offer full refurbishment services. Inspection is invited at our premises in Uttoxeter, Staffordshire, United Kingdom (close to East Midlands, Birmingham and Manchester airports). Powder Process Design Services Ltd has been supplying equipment and systems to the industrial minerals sector for over 20 years. We specialise in the design and supply of minerals processing systems using a combination of new and s/hand refurbished equipment. With approaching 40 years experience we aim to deliver projects that meet and indeed exceed clients expectations. We have satisfied customers throughout the world, including, the United States, South America, New Zealand, South Africa the Middle East and the UK and Ireland. Please check out our other listings and subscribe to our stock list.

Condition: good (used), Year of construction: 2015, Atlas Copco Oil Free Screw Compressor with built-in Air Dryer Chsdpfx Ajy Iplfjgrsd Model SF2+FF 7.75 bar / 112 PSI Year 2015 400 volts three phase, 2.2 KW / 3 HP, 2885 RPM 8.9 CFM / 4.21 lts/s Very little use Ex Pharma Facility

Condition: used, Year of construction: 1998, Used ultrat​​roc SD 0630 refrigerant dryer from ultrafilter for drying compressed air. The unit was manufactured in 1998 and features an integrated condensate drain. Manufacturer: ultrat​​roc GmbH Drucklufttechnik / ultrafilter Chsdo Ahy Nwepfx Agrjd Type: SD 0630 / 914 Year of manufacture: 1998 Max. permissible pressure, compressed air side: 16 bar Max. permissible pressure, refrigerant side ND/HD: 16 / 20 bar Max. permissible temperature, compressed air side: 60 °C Permissible ambient temperature: +2 to +50 °C Operating voltage: 230 V Phases: 1/N Frequency: 50 Hz Rated power consumption: 1.130 kW Protection class: IP20 Refrigerant: R134a Max. refrigerant charge: 1.250 kg Max. fuse rating: 16 A Features: Condensate drain

Condition: used, functionality: fully functional, This used Jungheinrich MPB pallet racking system is a compact, high-performance heavy-duty racking system for industrial storage requirements. The modular high-bay racking system is ideal for logistics, industry, large warehouses, and freight forwarding companies. With a load capacity of 2,400 kg per shelf level and a bay load capacity of 4,800 kg, this immediately available pallet racking system offers an efficient solution for storing Euro pallets and heavy load units. PRODUCT DETAILS: - Height: approx. 420 cm - Depth: approx. 110 cm - Length: approx. 30.80 m - Shelf load capacity: 2,400 kg per level - Bay load capacity: 4,800 kg - Beams: approx. 270 × 12.5 × 5 cm - Beam color: yellow painted - Uprights: approx. 650 × 110 cm, pre-assembled - Upright color: blue painted - Levels: ground + 2 beam levels - Pallet spaces: 99 including ground spaces - Condition: Used, Jungheinrich MPB SCOPE OF DELIVERY: - 12 × Uprights, approx. 520 × 110 cm, pre-assembled - 44 × Beams, approx. 270 × 12.5 × 5 cm - 88 × Safety pins PRICE: €2,440.00 net €2,903.60 gross You will receive an invoice with VAT shown. Codpfx As Ah Rx Sogrjhd DELIVERY, INSTALLATION & INSPECTION: - Nationwide delivery by our partner shipping company – freight costs depend on the postal code - Professional assembly and disassembly by trained teams, optionally available - Racking inspections according to DIN EN 15635 by certified inspectors - Inspection of existing heavy-duty racking systems from other manufacturers is also possible PLANNING & CONSULTATION: Our planning department will be happy to prepare a non-binding offer for you – tailored to your individual requirements. Whether it's a new installation, renovation, or expansion – we will provide you with competent advice on your racking configuration. SHOWROOM: Feel free to visit us in our showroom! On-site, you can get a comprehensive overview of our pallet racking systems, storage racking systems, and other solutions. Many systems are set up and can be experienced directly. Our technical consultants are available to answer your questions and provide individual advice – we look forward to your visit! HAVEN'T FOUND THE RIGHT ONE YET? Visit our website. Here you will find a quick overview of many other offers and models. ARE YOU INTERESTED OR DO YOU HAVE QUESTIONS? Simply contact us by message or phone. You will find our telephone number on our company website. ☎️ You can reach us by phone from Monday to Friday from 08:00 to 16:00. Alternatively, you can send us a message with your name and telephone number. We will get back to you as soon as possible.