Used Shoe Press for sale (12,671)

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: Hodpsy R Nnfsfx Ag Ionl The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: used, functionality: fully functional, This listing is for a second-hand ‘Schulze Air 4 Press’ pneumatic rotary press Condition: This is a second-hand machine, which may show signs of wear (minor scratches or discolouration). The unit has been tested for functionality Packaging and shipping: Hnjdpfx Aoy R Nm Ueg Ijl You are welcome to view the unit during our business hours. Please arrange an appointment! Seaworthy packaging and worldwide shipping available on request! A functional test will be recorded on video for you prior to dispatch or collection. For further information, you are of course welcome to contact us directly.

Condition: used, This listing is for a second-hand DTG/DTF printer, the ‘Brother GTX 423Pro’ Items included: 1 x Brother GTX 423Pro with the following accessories: Includes Lotus Heat Press LTS 150B Slide Includes Schulze PreTreat maker 5 Meter readings: Total: Approx. 5,500 prints Condition: This listing is for a second-hand device, which may show signs of use Hnjdpfx Aey R Nmhjg Iel (minor scratches or discolouration). The device has been tested for functionality A test print can be seen in the photo Packaging and shipping: You are welcome to view the device during our business hours. Please arrange an appointment for this! Seaworthy packaging and worldwide shipping available on request! A functional test will be recorded on video for you prior to dispatch or collection. For further information, you are of course welcome to contact us directly.

Condition: new, Year of construction: 2025, pressure 060 t stroke 350 mm table surface area 750x344 mm dayligth 197/750 mm distance between columns 750 mm diameter of piston 75 mm Hodpfjxu Nvzjx Ag Ionl

Condition: new, Year of construction: 2025, pressure 100 t stroke 380 mm table surface area 1100x424 mm dayligth 180/750 mm distance between columns 1100 mm Hnodjxu Nv Ijpfx Ag Iol diameter of piston 90 mm

Condition: new, Year of construction: 2022, pressure 55 t stroke 37 Min./20 mm Hnedpfjwp Tcqex Ag Iol throat 500 mm stroke max. 60 mm work height max. 1060 mm total power requirement 5 kW

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Features and technical data: - Clearly arranged controls - Ideal working height Hsdpfx Agoy R Haxe Ienl - Large opening - Full access from all four sides - Push-button control - Stop button - Safety line – emergency stop (E-STOP) accessible from any position - Timer with acoustic signal - Automatic pressure switch - Automatic temperature control system - Infinitely variable stroke limitation - Heavy-duty rack compensation - Energy-saving mode as standard - Switchable side cylinders - Total pressing force: 120 tons - Plate dimensions: 3000 x 1350 mm - Number of cylinders: 6 - Piston diameter: 85 mm - Max. opening/stroke: 400 mm - Closing time: approx. 16 sec - Heating time to 80°C (from room temperature): approx. 14 min - Maximum permitted operating temperature: 140°C - Total connected load: 20.1 kW - Hydraulic power: 1.21 kW - Circuit breaker: 35 A - Dimensions: 3500 x 1610 x 2000 mm - Total weight: 6200 kg Availability: short-term Location: 63934 Röllbach

Condition: used, Eccentric Press, Köszeg (Elzett) 6.3 Tons, Used Machine Manufacturer: Köszeg (Elzett) Hnedpfoy R Eb Isx Ag Isl Overall dimensions: Width: 600 mm Depth: 800 mm Height: 1600 mm Weight: 252 kg Pressing force: approx. 6.3 tons Stroke length: 130 mm Table size: 280 × 170 mm

Condition: used, Eccentric Press, MABU-PRESSEN 6 TF, Used Machine Manufacturer: MABU-PRESSEN Maschinenfabrik K. Burkard KG Type: 6 TF Overall dimensions: Hedpfx Agjy R Ebus Isnl Width: 700 mm Depth: 770 mm Height: 1570 mm Weight: 310 kg Year of manufacture: 1973 Pressing force: 6000 kg (6 tons) Stroke length: 6 / 60 mm Stroke rate: 220 strokes/minute Required motor power: 0.7 PS Table size: 400 × 215 mm

Condition: used, Eccentric Press, Crank Press, Ateliers Soenen 15T, Used Machine Manufacturer: Ateliers Soenen Type: Presse à Excentrique 15 Tonnes Overall dimensions: Hsdey R A Avjpfx Ag Isnl Width: 620 mm Depth: 900 mm Height: 1680 mm Weight: 581 kg Pressing force: 15 tons Stroke length (adjustable): between 10 mm and 50 mm Connecting rod adjustment: 30 mm Stroke rate: 130 strokes/minute

Condition: good (used), Year of construction: 2002, functionality: fully functional, stroke length: 365 mm, throat depth: 410 mm, Hydraulic Press Brake Make: TRUMPF Model: TrumaBend V85 Year: 2002 Technical Specifications Manufacturer: Trumpf Model: TrumaBend V85 Year of manufacture: 2002 Press force: 85 t Stroke: 365 mm Bending length: 2050 mm Frame gap: 1750 mm Throat depth: 410 mm Table width: 120 mm Working height: 1050 mm Dimensions (approx.): L 2.6 x W 1.80 (plus 0.5 m support arms) x H 2.90 m Weight: approx. 9,050 kg Equipment • Control: Delem DA 2D Graphic • 2 movable support arms Hnodpfx Aoy R Arksg Ijl • Pneumatic die shifting • Hydraulic tool clamping, top and bottom • CNC-controlled crowning • Controlled axes: X1, X2, R1, R2, Z1, Z2 • Gooseneck upper tool, 86°/R1, H 120 mm, L = 1,960 mm, segmented • Straight upper tool OW202/K 28°/R1, H 120 mm, L = 1,935 mm, segmented • Lower tool V10/84°, R1, H 100 mm, L = 2,050 mm, segmented • Lower tool V24/80°, R 2.5 mm, H 100 mm, L = 2,000 mm, segmented • Lower tool V16, L = 1,000 mm • Lower tool V30, L = 500 mm All information without guarantee. A demonstration under power is possible at any time in our exhibition hall.

Condition: used, Friction press, flywheel press, forging press, screw press, used machine Manufacturer: ASJ Type: J53-160B Overall dimensions: Hnedpoxpf U Ajfx Ag Iel Width: 1850 mm Depth: 1380 mm Height: 3140 mm Weight: 8190 kg Table size: 560 × 510 mm Clear opening without table: 560 × 560 mm Clear opening with table: 260 mm Nominal pressure: 160 tons Stroke length: 360 mm

Condition: ready for operation (used), Hydraulic press, four-column press, Eitel 100T Manufacturer: EITEL Pressing force: 100 tons Overall dimensions: 1900x1100x3300mm Table size: 1050x800mm Hedpfxouhl E Re Ag Ienl Stroke length: 400mm

Condition: ready for operation (used), Hydraulic Press Machine, Coil Winding Press Machine, Used Equipment Hnodpfx Agju Hkfpe Iel Dimensions: 1340 x 1240 x 2740 mm Weight: 640 kg Electrical Specifications: 400V Hydraulic Pressure: 100 bar Stroke Length: 180 mm

Condition: ready for operation (used), Design: vertical press with four columns. The vertical press platen is driven by an electric motor, the lower platen can be pulled out with the tool. -Dimensions: 2100x1600x3000mm -plate size: 950x1120mm -Electrical data: 380V; 43A; 22kW Hsdpfotty Nkox Ag Ienl

Condition: used, Press machine, REMS Power-Press XL ACC, used equipment Manufacturer: Rems Type: Power-Press XL ACC Pressing range: Ø 10 – 108 mm (up to 110 mm) Pressing force: 32 kN Motor: 450 W universal motor Power supply: 230 V or 110 V, 50–60 Hz Weight: approx. 5.5 kg Dimensions (H x W x D): 800 x 335 x 230 mm Cable length: 2900 mm Accessories: more than 400 types of REMS pressing jaws, adapters for other manufacturers Hjdpfxexlp T Io Ag Isnl Additional features: Automatic retraction (Automatic Circuit Control – ACC) Rotatable pressing jaw holder with automatic lock Compatible with pressing jaws from other manufacturers Fast pressing, e.g., Geberit Mapress stainless steel Ø 108 mm connection in 15 seconds Press jaws: 76.1; 88.9; 108 mm

Condition: ready for operation (used), REMS press tool, cordless press ACC Li-Ion Plus, Used machine Manufacturer: Rems Type: ACC Li-Ion Plus Overall dimensions: Width: 520 mm Depth: 290 mm Height: 120 mm Key features: Electro-hydraulic drive Pressing force: 32 kN Suitable for pipe press fittings Ø 10–108 mm (up to 110 mm in some cases) Universal motor: 1850 W Battery: Li-Ion 14.4 V / 3.0 Ah (Li-Ion Plus technology) Multifunctional electronics: soft start, overload protection, automatic retraction (ACC) 360° rotatable jaw holder Built-in LED work light Ergonomic, lightweight design: approx. 4.3 kg Hnedpfx Agexl E Nfs Ijl Condition: Used, in good working order. Accessories: battery, charger

Condition: good (used), Year of construction: 2000, functionality: fully functional, operating hours: 27,169 h, Hydraulic Press Brake Make: TRUMPF Model: TrumaBend V130 Year: 2000 Technical Data Brand: TRUMPF Model: TrumaBend V130 Year of manufacture: 2000 Operating hours: 27,169 h (read off) Press force: 130 t Bending length: 3050 mm Stroke: 365 mm Operating pressure: 340 bar Dimensions: approx. L 3.80 x W 2.40 x H 2.95 m Weight: approx. 13 t Equipment • Controlled axes: Y1, Y2, X, R • Movable support arms Hnodey Ryfuopfx Ag Iol • CNC controlled crowning • Delem 2D graphical control • Hydraulic upper tool clamping • Pneumatic die displacement • Upper tool: straight 28°, R1.0, H 140mm, L = 3,050mm, segmented • Die V12/30°, R1, H 100mm, L = 3,000mm, segmented • Die V30/80°, R5, H 100mm, L = 3,000mm (6x500) • Die V60/80°, R5, H 100mm, L = 3,000mm (6x500) All information without guarantee. A demonstration under power is possible at any time in our showroom.

Condition: used, Year of construction: 1994, CNC press brake Manufacturer: Blemas Model: 100-33 Year of manufacture: 1994 CNC control: Cybelec DNC 74 PSG Pressing force: 100 t Hjdpfx Agoyvfkle Isnl Working width: 3 m Weight approx.: 8 t Dimensions approx.: 3,600 x 1,600 x 2,600 mm

Condition: excellent (used), 4-axis hydraulic CNC press brake with HACO-Robosoft ATS 590 Graphic control unit (modernized in 2008) and CE conformity Press force: 135 t Bending length: 4000 mm Dimensions (L x W x H): approx. 4500 x 1600 x 2430 mm Weight: 10,500 kg Accessories / Special features: • 4-axis CNC control HACO ATS 590 Graphic (axes Y1 + Y2, X, R) for stroke depth, back gauge, and back gauge fingers (top/middle/bottom) • Back gauge fingers can be manually set together/apart • Graphical programming and display • CE-compliant due to single working speed • Hydraulic synchronization control • Manual crowning adjustment with handwheel under the die, featuring SIKO position indicator • Segmental upper tools, as new • Continuous universal die with 4 different V-openings (up to max. V = 40 mm), as new • Additional segmented upper and lower tools • Busbar • PROMECAM tool clamping system • 2 support arms • Fast, precise, and easy to adjust • Foot pedal and emergency stop • Electrically interlocked safety doors (right, left, rear) • Single working speed, fast return stroke • CE-compliant Safety inspection (UVV) valid until 04/2027 Delivery: immediately ex stock Dortmund, free loaded on truck Siegfried Volz Werkzeugmaschinen Hnedpfx Agsx Npiye Ijl Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Condition: good (used), input voltage: 400 V, input frequency: 50 Hz, DGUV certified until: 03/2027, type of input current: three-phase, Dough Divider and Rounder Record Automat Roll Press for dividing and rounding 30-piece / 25 to 85 grams per piece Hnodpfx Asrhfp Ueg Iel with 3 rounding plates Connection: 400V, 16A-CEE plug Dimensions: 690 x 580 x 1650 mm (W x D x H) Used machine Delivery service Many more roll presses in stock!

Condition: good (used), Year of construction: 2005, power: 15 kW (20.39 HP), operating speed: 10 mm/s, total length: 4,000 mm, total width: 2,000 mm, total height: 3,000 mm, overall weight: 11,500 kg, controller manufacturer: Delem DA65, working width: 3,100 mm, bending force (max.): 175 t, distance between stands: 2,550 mm, control type: CNC control, number of axes: 5, Max. bending length: 3100mm Distance between column: 2550mm Max. pressing force: 175T Beam stroke: 225mm Table Width: 150mm Troth beam: 400mm Approch speed: 100mm/min. Working speed: 10mm/min. Hnjdpfxsyvz H Re Ag Iol Return speed: 100mm/min. Adjustment X-Axis back gauge:1000mm Number of controlled axis: 5 Control: yes Crowning: yes Hydraulic toolclamping: yes Power: 15kW Length: 4000mm Width: 2000mm Height: 3000mm Weight: 11500kg

Condition: good (used), Make: Ursviken Type: VPF 1000/800-5,0 Control: Siemens Simatic panel Year: 1970 Hydraulic press for fabrication off large componts like dish heads tanks boiler shipyard and steelconstruction Renewed in 2015 with Siemens SIMATIC panel and E-Cabinet Rittal Build in height 2950 mm Maximum die height 1500 mm Movable Table & Piston in X-Ways Large package Die tooling radius 10/20/30/50/60/80/100 Pressing force 210 kg/cm2 Maximum stroke 800 mm Machine 2350 mm placed in ground Specifications Metric US Standard Capacity Kg 1000 Ton Distance between column 5010 mm Table Length 3000 mm Table Width 2000 mm Table Height 550 mm Ram stroke 1450 mm Approche speed 50 mm/min. Working speed 5 mm/min. Return speed 50 mm/min. Dimensions (Estimate) Length 0 mm Width 0 mm Height 0 mm Hedpfx Agjkvmi So Ionl Weight 0 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Manufacturer: WMW Zeulenroda Type: PYE 160 SS Year of manufacture: 1980 C-frame construction Die height 850 mm Thickness bolster plate 100 mm Throat C side 360 mm Specifications Metric US Standard Capacity 160,000 Table length 1,250 mm Table width 600 mm Ram stroke 500 mm Starting speed 100 mm/min Working speed 10 mm/min Return speed 125 mm/min Power 22.5 kW Dimensions (Estimate) Hjdpfxjwp Nv Ho Ag Ienl Length: 2,150 mm Width: 1,250 mm Height: 3,600 mm Weight: 7,500 kg Please note: The information on this page has been provided to the best of our knowledge and, where possible, from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not represent a warranty or contract terms. We recommend you check all important details.

Condition: good (used), Hydraulic press TCS - 150T MACH-ID 8821 Manufacturer: TCS Type: 150T Control system: Siemens SIMATIC OP7 Year of manufacture: 1999 Table load sliding table 20000 Kg Table load upper table 9000 kg Table out feed stroke 2100 mm Column diamater 180 mm Closing force 1500 Kn Hsdpfx Asulwzmog Ionl Opening force 700 Kn Laser safe CE Safety Power 15 kW Specifications Metric US Standard Distance between uprights 2000 mm Installation height 2000 mm Table length 1500 x 2000 mm ram stroke 1800 mm Starting speed 50 mm/min. Working speed 8 mm/min. Return speed 50 mm/min. Table rotation 0 - 270 rpm Table rotation 0 - 180 ° Dimensions (estimation) length 4800 mm width 5600 mm height 5200 mm Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.