Used Shark 282 Ccs for sale (4,036)

Condition: reconditioned (used), Year of construction: 2015, Used automatic hydraulic band saw for metal MEP Shark 230 nc hs 5.0 Automatic auger chip remover Blade size: 2950x27x0.9 Choice of cutting speed with inverterr: from 15-100 m/min Capacity: round 230mm, square 230x230mm Year: 2015 Possibility of cuts also in semi-automatic mode The machine has been fully serviced, the following parts have been replaced: all bearings, reducers, both wheels (pulleys) leaf, hard metal plates in guides, main shaft, coolant pump, two jaws, coolant pipes,yojstick, fans and other consumables. Lasdpfx Anotva Nhjusc

Condition: as good as new (ex-display), Year of construction: 2024, Special machine for shredding plastics Base machine from €24,990 net Well-suited for shredding: - Paper, cardboard, pipes, profiles, boxes, canisters, buckets, cans, sections of wooden pallets, etc. - Semi-rigid thermoplastics such as PVC, PP, PE, PS, PU, PET Includes: - Special rotor with embedded blades (reduced load absorption), - Small cutting gap between blade and counter-blade Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Control: PLC Cutting unit opening (top) 600 x 800 mm The parts should be a maximum of approx. 500x500 mm *the height is less relevant Hydraulically operated slide Screen size as required (25 - 40mm) For plastics, coarser screens are recommended (30-40 mm) *If you want to shred finer, a two-stage shredding process with a downstream granulator type MVZ (screens 5-15 mm) is recommended. Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (l x w x h) approx. 1737 x 1167 x 1650 mm Further options available at an extra charge: - Raise shredder by approx. 25 cm (preparation for conveyor belt removal) + €1,980 net - Inclined conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) - Alternatively, manual start and stop on the conveyor belt + €595 net Requirements for the raw material: - The moisture content (as received) must be below 25% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear. We would be happy to offer a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. It is also possible for you to send us your material by freight forwarder, and we will document the test with photos and videos. --- *only for brittle plastics with medium hardness, *not for elastic or extremely hard and heavy plastics - this would affect the durability of the system. --- Optionally, the next larger machines would be available: Base machine: Shredder MGZ 830 K-S - 18.5 kW Cutting unit opening (top) 800 x 1,000 mm The parts should be a maximum of approx. 720x700 mm *the height is less relevant from €39,995 net * Options depending on effort Base machine: Shredder MGZ 1030 K-S - 22 kW Cutting unit opening (top) 1,000 x 1,000 mm The parts should be a maximum of approx. 900x700 mm *the height is less relevant Lodpfxjd H R Sxe Anueac from €49,975 net * Options depending on effort Base machine: Shredder MGZ 1330 K-S - 37 kW Cutting unit opening (top) 1,300 x 1,200 mm The parts should be a maximum of approx. 1,200x700 mm *the height is less relevant from €79,975 net * Options depending on effort

Year of construction: 2025, condition: new, to sell the demonstration machine at a special price Our MVZ 7.5 granulator is suitable for shredding thin-walled parts and/or for post-shredding wood chips. More details after a test with your material. Larger systems are also available as an option The price is only for the shredder as shown in picture 1 - fan, cyclone and filter are options. Motor: 7.5 kW *larger systems on request (4 to 75 kW) Throughput up to 120 kg/h *depending on screen and material Much higher throughput rates can be achieved with the secondary shredding of wood chips. Details after the test with about 30 kg. Rotor diameter: 180 mm 6 rotary knives each 225 mm 4 stationary knives each 225 mm Dimensions: 930x730x1420mm weight: 450 kg, Ledpfxjd N Dn Ds Anujac suction nozzle: 100 mm, Screens: 6.8 and 15 mm - other screens available, Price per sieve: €390. Price set replacement knife: 579 € Suitable e.g. fur: - Plastic waste of all Art.-No Various materials - HDPE, LDPE, PP, PS. PC, PA - biomass -Wood - Herbs etc. Parts from injection molding, blow molding, injection molding scrap, small bottles, cables, small pipes, profiles, etc

Condition: used, Number of sanding units 4 st. Laodpfjxr N I Ejx Anujc sanding width 1.300 mm Sanding height max. ca. 140 mm

Condition: new, Year of construction: 2026, functionality: fully functional, *All of our products are made with care and covered for 1 year warranty! *Installation and Operator Training FREE Cone crusher product group is designed especially for the hardest material, cone crushers are one of the best choices for crushing river gravel, basalt and granite, along with abrasive materials in the mining industry. The working principle of cone crushers is to break the material by compression, by squeezing it between its walls, which are completely covered with resistant mantle and a bowl liner. It has longer life than other crushers thanks to its long life wear parts. Model: FABO CCS-440 Capacity: 300-550 t/h Max. Feed opening; EC 450 mm C 400 mm MC 300 mm Motor: 220-250 kW, Head diameter: 1300 mm Dimensions (width * height): 3100 *2850 mm Countershaft Speed-rpm: 750-1200 Lasdpfoy Tnylex Anujc Weight: 31000 kg * Hydroset Control * Automatic Load Protection * Practical discharge * High capacity cubic production * High-performance contactless labyrinth * High productivity, low energy production and lower wear costs, long service life and high product yield with desired fine powders. FOR FURTHER INFORMATION PLEASE FEEL FREE TO CALL US!!!

Condition: good (used), Year of construction: 2015, cutting range 300 mm capacity 90 degrees: flat 330 x 260 mm capacity 90 degrees: square 260 x 260 mm capacity 45 degrees: round 260 mm capacity 45 degrees: flat 270 x 200 mm capacity 45 degrees: square 250 mm capacity 60 degrees: round 180 mm capacity 60 degrees: flat 170 x 170 mm capacity 60 degrees: square 180 mm automatic feeds 9999,9 mm feed minimum 2.0 mm cutting diameter minimum 5.0 mm band speed 15 - 100 m/min vice 340 mm Öffnung dimensions of saw-band 3650 x 27 x 0,9 mm Control MEP CNC total power requirement 2.2 kW weight 1240 kg range L-W-H 1800 x 1900 x 1750 mm actual NEW price about 23.000 Euro special price on request Equipment: - robust electro-hydraulic fully automatic band saw (INDUSTRY) - with additional semi-automatic function, for cuts from 0° to 60° left - WINDOWS “CE” based MEP 50 – control and 7” touch screen display * simple and quick setting of all machine parameters * with additional soft keys + backlit display * 10 programs, each with a maximum of 9999 pieces and . a maximum length of 9999.9 mm - material feed with stepper motor via ball screw * single stroke 600 mm repeatable to saw any length * accuracy of ± 0.1/600 mm - feeder with protective cover and safety limit switch - precise setting of the cutting feed with indication in mm/min - positioning of the saw head and movement of the feeder using a joystick - automatic detection of the start of the cut - large deflection discs, adjustable from cast steel - Saw blade tension with blade tension control and display - Hard metal blade guides for maximum cutting precision - Automatic monitoring of the cutting load - Vice with quick adjustment * with interchangeable clamping and stop jaws - Large, laterally extendable chip tray and coolant container Laodoy I Da Rjpfx Anuoc * equipped with 2 electric pumps for lubricating and cooling the saw blade * Coolant gun for cleaning the machine - Chip removal brush for cleaning the saw blade - Operating instructions DE Information from the manufacturer: When installing this saw in a network with a residual current device (FI), this should be universally current sensitive and not less than 300 mA.

Condition: used, Year of construction: 2007, We offer the complete WEBER line designed for slicing, inspection, and product conveyance in food processing plants. The line consists of: Laedpfxey N Shro Anuec WEBER CCS 304 slicer, WIPOTEC WEB 99 LC scale, WEBER CMB reject conveyor, WEBER CCL belt conveyor, spare parts, including a blade sharpener. This setup allows for a seamless product flow from the slicing stage, through weight control, to the collection and potential rejection of products that do not meet the specified parameters. This solution is particularly useful wherever portion consistency, quality control, and process automation are critical. Technical specifications: WEBER CCS 304 slicer Manufacturer: WEBER Type: CCS 304 No.: 650 Year of manufacture: 2007 Capacity: 400 slices/min Slicing thickness: 0.5 mm – 50 mm Power supply: 400V 50Hz 3N Power: 5 kW Air pressure: 6 bar Air consumption: 300 l/min WIPOTEC WEB 99 LC Scale Manufacturer: WIPOTEC Model: WEB 99 LC (Weighing Module) Year of manufacture: 2007 Max: 1500 g DL: 15000 g WEBER CMB Rejection Feeder Manufacturer: WEBER Type: CMB Year of manufacture: 08/2007 WEBER CCL Belt Feeder Manufacturer: WEBER Type: CCL No.: 3650 Year of manufacture: 08/2007 Applications of the WEBER line The WEBER line is ideal for processing and transporting various food products requiring: precise slicing, weight control, automatic transport, and rejection of products outside the specified range. Key advantages of the WEBER line combination of slicing, weighing, and transport in a single line, greater portion repeatability and product control, automatic rejection feeder, smooth product flow thanks to the belt feeder, industrial design from renowned manufacturers WEBER and WIPOTEC, a good option for facilities looking for a used, complete production line.

Condition: excellent (used), Year of construction: 2009, operating hours: 10,720 h, functionality: fully functional, Willibald EP 5500 Shark in excellent condition and ready for work. Ljdpfx Ansy Iwgksuoac

Condition: used, Year of construction: 2014, operating hours: 7,400 h, functionality: fully functional, BRAND: WILLIBALD MODEL: EP5500 Lajdoy Iwa Repfx Anuoc YEAR: 2014 HOURS: 7,400 EXTRAS: 48 hammers SERIAL NUMBER: #134 REGISTRATION NUMBER: 98.14.XX-552

Condition: new, cutting diameter 300 mm capacity 90 degrees: flat 330 x 260 mm capacity 90 degrees: square 260 x 260 mm capacity 45 degrees: round 260 mm capacity 45 degrees: flat 270 x 200 mm capacity 60 degrees: round 180 mm capacity 60 degrees: flat 170 x 170 mm height of material-table 600 mm Pitch min/max 50.000 mm vice 335 mm Öffnung band speed 15 - 100 m/min automatic feeds 600 mm dimensions of saw-band 3650 x 27 x 0,9 mm Control MEP CNC total power requirement 2.2 kW weight 1.105 kg range L-W-H 3,3 x 2,83 x 2,23 m electro-hydraulic band saw fully automatic, with additional : * semi-automatic * semi-automatic-dynamic * manual .. operation Description: - robust electro-hydraulic band saw fully automatic (INDUSTRY) * MEP - WINDOWS numerical control unit * User interface with 7” touch screen display * mechanical buttons for the sawing machine’s operating functions * guarantees reliable operation, simple and intuitive * real-time control of all cutting parameters * pivoting arm enables comfortable and safe operation * display and recording of alarm and error messages - miter cuts with automatic cycle from 0° to 60° left Laedpfexabavsx Anuoc - semi-automatic, semi-automatic-dynamic and manual cycle * miter cuts from 45° right to 60° left - manual or semi-automatic dynamic cycle selectable * to make cuts without programming - protective housing for the safety of the worker - continuous regulation of the cutting speed from 15 to 100 m/min * via frequency converter (inverter) - Latest generation hydraulic unit * extremely powerful with low energy consumption. - Material feed with stepper motor via ball screw * mounted on opposing ball bearings * Single stroke 600 mm repeatable to saw any length. - Positioning of the saw head and movement of the feeder using a joystick. - Automatic detection of the start of the cut position - Manually operated band tension control with indication on the display * using an electronic converter - Automatic monitoring of the cutting load * using a servo valve mounted directly on the cylinder - The coolant tray is built into the base frame - Chip removal brush - Bimetal saw band for solid and profile material - Tools and instructions for use with spare parts list * Angularity = 2/12 degrees * Length accuracy = plus/minus 0.1 mm per feed

Condition: new, cutting range 300 mm capacity 90 degrees: flat 330 x 260 mm capacity 90 degrees: square 260 x 260 mm capacity 45 degrees: round 260 mm capacity 45 degrees: flat 270 x 200 mm capacity 45 degrees: square 250 mm capacity 60 degrees: round 180 mm capacity 60 degrees: flat 170 x 170 mm capacity 60 degrees: square 180 mm automatic feeds 9999,9 mm feed minimum 2 mm cutting diameter minimum 5 mm band speed 15 - 100 m/min vice 340 mm Öffnung dimensions of saw-band 3650 x 27 x 0,9 mm Control MPE CNC total power requirement 2,2 kW weight 1240 kg range L-W-H 1800 x 1900 x 1750 mm Equipment: - robust electro-hydraulic fully automatic band saw (INDUSTRY) - with additional semi-automatic function, for cuts from 0° to 60° left - WINDOWS “CE” based MEP 50 – control and 7” touch screen display Laodsxaa Ewspfx Anusc * simple and quick setting of all machine parameters * with additional soft keys + backlit display * 10 programs, each with a maximum of 9999 pieces and . a maximum length of 9999.9 mm - material feed with stepper motor via ball screw * single stroke 600 mm repeatable to saw any length * accuracy of ± 0.1/600 mm - feeder with protective cover and safety limit switch - precise setting of the cutting feed with indication in mm/min - positioning of the saw head and movement of the feeder using a joystick - automatic detection of the start of the cut - large deflection discs, adjustable from cast steel - Saw blade tension with blade tension control and display - Hard metal blade guides for maximum cutting precision - Automatic monitoring of the cutting load - Vice with quick adjustment * with interchangeable clamping and stop jaws - Large, laterally extendable chip tray and coolant container * equipped with 2 electric pumps for lubricating and cooling the saw blade * Coolant gun for cleaning the machine - Chip removal brush for cleaning the saw blade - Operating instructions DE Information from the manufacturer: When installing this saw in a network with a residual current device (FI), this should be universally current sensitive and not less than 300 mA.

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, power: 12.6 kW (17.13 HP), workpiece height (max.): 50 mm, edge thickness (max.): 15 mm, feed rate X-axis: 22 m/min, overall weight: 3,200 kg, year of last overhaul: 2024, Ott Shark Edgebander for PUR The machine is fully functional and can be viewed and tested on site! The machine was completely overhauled by a specialized company 2 years ago! Equipment: - Angle stop for small parts - Release agent spray unit - Joint trimming unit - Pressure unit - Crosscut saw - Profile trimming unit - Profile milling unit (R2) Lsdpfjy H Dx Dsx Anueac - Radius scraper blade - Corner copying unit - Flat scraper blade - Polishing station (oscillating) Additionally included: - PUR glue pot - EVA glue pot - Service station with vacuum box and cleaning/boiling station

Condition: new, cutting diameter 300 mm capacity 90 degrees: flat 330 x 260 mm capacity 90 degrees: square 260 x 260 mm Lasdpfxofg E H Ue Anuec capacity 45 degrees: flat 270 x 200 mm capacity 45 degrees: round 260 mm capacity 45 degrees: square 250 x 250 mm capacity 60 degrees: flat 170 x 170 mm capacity 60 degrees: square 170 x 170 mm capacity 60 degrees: round 180 mm turning speed range: 40 / 80 m/min dimensions of saw-band 3320 x 27 x 0,9 mm engine output 1,5 / 1,8 kW weight 670 kg Electro-hydraulic semi-automatic band saw SHARK 332 SXI EVO with semi-automatic-dynamic, manual function, has a MEP-28 control for miter cuts from 45° right to 60° left. Some features: New centralized switch console on an articulated arm. Low voltage control panel: Polyester membrane keyboard with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in the user language) * Alarms (description of alarm causes) * State of inputs and outputs * Counting cuts * Time taken for the cut made * Current consumption of the saw blade motor * Saw blade tension * Blade speed * Numerical display of head position. Switch handle IP55 of manual 24V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for special ones Applications New, latest generation hydraulic control unit, extremely powerful and with low energy consumption. Turntable (on roller bearings of 420 mm with preloaded thrust bearings assembled). Double belt speed (40/80 m/min.) with control Intended to accommodate an electronic inverter for the Continuous regulation of the belt speed from 20 to 90 m/min. Stroke of the saw bow can be programmed directly from the control panel Adaptation to the cutting material. Clamping device can be moved laterally to the left and right Quick release vice. Manually operated strap tension control with display on the screen electronic converter. Base designed to completely contain the coolant, even with maximum angle cuts. The coolant pan (provided with an electric pump for lubrication and Cooling of the saw band) and the chip drawer (can be replaced by a Chip conveyor to be replaced - see special accessories) are in the base frame built-in. Preparation for installing the minimum blade lubrication kit (Optional, in addition to the conventional standard lubrication with emulsion oil. Chip clearing brush. The machine is intended for pallet truck transport. Adjustable length stop for cuts of the same length Material support arm with roller for attaching the loading platform Bimetal saw band for solid and profile material. Tools and instructions for use in the respective user language.

Condition: new, 230 mm 230 x 230 mm saw band length 2950 x 27 x 0,9 mm band speed 15 - 100 m/min total power requirement 2,2 kW weight of the machine ca. 1,2 t SHARK 230-1 NC HS 5.0, electro-hydraulic two-column fully automatic band saw with Laedpfx Aefg E Hyjnujc semi-automatic function for 0° cuts of mild steel, stainless steel, Steel alloys, solid and profile material, with a maximum remaining piece length of 60 mm. - The cross section is max. 230x230 mm. - Numerically controlled band saw machines with the new, specially designed by MEP developed for Automatic Windows “CE” based E FEATURES: - User interface with 7” touch screen display and mechanical buttons for the operating functions of the sawing machine, guaranteed reliable Operation, simple and intuitive, and real-time control of all Cutting parameters. - Safety enclosure in accordance with the latest safety regulations Machinery Directive EN 13898/2007. - New fieldbus communication system with double microprocessor Serial connection. - Robust cast iron structure (G25) to compensate for vibrations Improve machine stability and protect the saw band

Condition: new, cutting diameter 300 mm saw band length 3320 x 27 x 0,9 mm mm cutting width 300 mm Control NC capacity 90 degrees: flat 330x 260 mm capacity 90 degrees: square 260 x 260 mm capacity 45 degrees: square 250 mm capacity 45 degrees: flat 270 x 200 mm capacity 60 degrees: round 180 mm capacity 60 degrees: square 170 mm band speed 15 - 100 m/min total power requirement 2,2 kW weight of the machine ca. 1,1 t dimensions of the machine ca. 3,3 x 2,83 x 2,23 m Furnishing: - fully automatic electro-hydraulic band saw with additional semi-automatic, semi-automatic-dynamic and manual operation - Automatic cycle (cuts from 0° to 60° left) - Semi-automatic, semi-automatic-dynamic and manual cycle (cuts from 45° right to 60° left) - Manual or semi-automatic dynamic cycle to make cuts outside of series production can be carried out directly without programming. - Numerically controlled band saw machines with the new, especially from MEP Windows CE based controller developed for automatic machines. - User interface with touch screen display of 7 and mechanical buttons for the operating functions of the sawing machine. - Stepless regulation of the cutting speed from 15 to 100 m/min Frequency converter (inverter). - Material feed with stepper motor via ball screw - which is mounted on opposite ball bearings; Single stroke 600 mm - repeatable to cut to any length. Lajdpfx Aofg E H Esnuec - Automatic monitoring of cutting load - through a servo valve mounted directly on the cylinder. - The coolant pan is installed in the base frame - Chip clearing brush. - Bimetal saw band for solid and profile material. - Tools and instructions for use with a list of spare parts

Condition: new, cutting diameter 280 mm capacity 90 degrees: flat 380 x 260 mm capacity 90 degrees: square 260 x 260 mm turning speed range: 40 / 80 m/min dimensions of saw-band 3440 x 27 x 0,9 mm engine output 1,5 / 1,8 kW Lajdpjfg E Iaofx Anusc weight 670 kg Electro-hydraulic, semi-automatic band saw with additional manual and semi-automatic-dynamic function, for cuts from 45° right to 60° left. Some features: Pivoting control panel on vertical post. 420 mm large rotary table on roller bearings with preloaded thrust bearing and replaceable steel inserts. Double belt speed (40/80 m/min.)

Condition: new, cutting diameter 250 mm capacity 90 degrees: flat 280 x 220 mm capacity 90 degrees: square 220 x 220 mm turning speed range: 36 / 72 m/min dimensions of saw-band 2950 x 25,4 x 0,9 mm weight of the machine ca. 0,4 t Dimensions (LxWxH) 1,5 x 0,9 x 1,5 Semi-automatic function: Vice closes and motor starts, saw head lowers Lsdofg E H Rjpfx Anujac for the cut, motor switches off, saw head rises, Vise opens. Some features: New centralized switch console on an articulated arm. Latest generation hydraulic control unit, highly powerful and with low energy consumption. Base frame with pull-out coolant container. The machine complies in all areas CE regulations!

Condition: used, Year of construction: 2024, Stump Grinder Suitable for Energreen RoboEVO & RoboFIFTI RS Technical Data Grinding Wheel Diameter: 480 mm Grinding Wheel Thickness: 95 (15) mm Lasdoy Eythepfx Anusc Grinding Teeth: 2 x 8 with double Widia inserts Approx. Weight: 315 kg L x W x H: 123 x 84 x 55 cm Swing Range: 150 cm Above Ground Level: 70 cm Below Ground Level: 40 cm (60 cm without grader blade) Working Pressure: 160 to 400 bar Hydraulic Connection: "CEJN" quick couplings We are pleased to offer you suitable financing, hire purchase, or leasing options. Delivery or shipping by arrangement. We always have a selection of both used and new machines in stock, as well as additional equipment available for demonstration. Feel free to contact us! We also rent all equipment with or without operator and machine. Other information: * Trade-ins and purchase of vehicles and machinery possible. * Sale price excludes transport. * No liability for printing or typing errors. * Subject to error, change, and prior sale. * Offer is non-binding. * Photos may differ. Price applies to current condition. * All details provided without guarantee. Further Information New: No

Condition: reconditioned (used), Used semi-automatic bandsaw MEP Shark 281 sxi evo Three operating modes: semi-automatic, manual, and manual dynamic (gravity) Lajdsyyn Sujpfx Anuoc Blade dimensions: 2950 x 27 x 0.9 mm Two blade speeds: 36/72 m/min Max vice opening: 285 mm Cutting capacity: at 0° round 250 mm, rectangle 280x200 mm at 45° round 190 mm, rectangle 180x180 mm at 60° round 120 mm, rectangle 110x110 mm Year: 2006 Weight: 435 kg Fully serviced.

Condition: new, Year of construction: 2016, functionality: fully functional, cooling capacity: 251 kW (341.26 HP), type of input current: three-phase, type of cooling: water, input voltage: 400 V, total width: 1,100 mm, total length: 1,600 mm, total height: 1,950 mm, warranty duration: 6 months, heating capacity: 282 kW (383.41 HP), Watercooled chiller/Heat pump Climaveneta NX WN 802 251 kW/282 kW Cooling capacity: 251 kW / 71.37 tons (12/7 — 35°C) Heating capacity: 282 kW / 80.19 tons (40/45 —7°C) Year of manufacture: 2016 Options: Heat pump Refrigerant circuit: 1 pcs. Heat exchanger: Plate Compressors: 2 pcs. Copeland ZP485KCE-TWD-522 (scroll) Type of refrigerant: R410a Dimensions: 1.6x1.1x1.95 m Working hours: 124/102 h. Condition: Outlet CONDITION, TESTING & READINESS The chiller / kaltwassersatz / undergoes seven stages of technical inspection and operational parameter verification. It is also tested at our own test station, with connection to water (or glycol) and adjustment of parameters according to your requirements. After testing, you will receive a detailed report with the operating performance and the overall condition of the chiller. The chiller / kaltwassersatz / is ready for transport and commissioning. Our engineers will assist you with cooling capacity calculations, selection of the appropriate cooling scheme, and configuration of the required equipment options. WARRANTY & SUPPORT The quality of the equipment is confirmed with a warranty ranging from 6 to 36 months. LOGISTICS - Worldwide delivery available - Support with loading, export documentation, and logistics coordination Get a detailed consultation. Photos, videos, and a full testing report can be provided immediately upon request. Ljdpfsv S Dlijx Anusac

Condition: new, Length: 1500 mm 6 rollers made of tubular steel, width: 185 mm Diameter: 20mm Height continuously adjustable: 650 - 1030 mm Lodofxu Tkopfx Anujac Space requirement: 1500 x 250 x 650/1030 mm

Condition: new, dimensions of saw-band 3650 x 27 x 0,9 mm speed 15 - 100 m/min vice 335 mm capacity 90 degrees: round 300 mm capacity 90 degrees: square 260 mm capacity 90 degrees: flat 330 x 260 mm capacity 45 degrees: round 260 / 200 mm capacity 45 degrees: square 250 / 180 mm capacity 45 degrees: flat 270 x 200 / 200 x 160 mm capacity 60 degrees: round 180 mm capacity 60 degrees: square 170 mm capacity 60 degrees: flat 170 x 170 mm total power requirement 2,2 kW weight 1.105 kg dimensions 2700 x 2300 x 1800 mm Fully automatic electro-hydraulic band saw with multi-micro processors and additionally semi-automatic, semi-automatic-dynamic and manual Function. - Automatic cycle (cuts from 0 ° to 60 ° link). CNC machine with two controlled axes that allow for the same material thickness 1000 various editing programs, each with a different cutting length and quantity, too program. - Semi-automatic, semi-automatic-dynamic and manual cycle (cuts from 45 ° right to 60 ° left) - Semiautomatic dynamic system (manual lowering of the saw band bow up to the desired position and cycle start via the push button.) - Manual or semi-automatic-dynamic cycle to cut directly without Programming. Some features: - New fieldbus communication system (Modbus protocol) - Display with 20 characters x 4 lines to display the technical parameters such as: - Saw blade speed - Number of programmed and executed cuts - saw blade thickness - feed length - cutting time - ammeter - belt tension - Display of (about 100) diagnostic messages and warnings, everything in the respective user language. - Display and entry of the alarm and error messages with the possibility of display incidents that have occurred. - automatic parameter setting via control, if a new driver or Inverter is mounted. - Electronic inverter for continuous regulation of the belt speed of 15 up to 100 m / min. - New hydraulic control unit of the latest generation, highly efficient and with low energy consumption. - New material supply of 600 mm with stepper motor and ball screw mounted on opposite ball bearings. - Hublauf the saw blade directly from the control panel programmable, for Adaptation to the cutting material. - Electronic band tension control. - Automatic monitoring of the cutting load by a direct on the Cylinder mounted servo valve. - The coolant sump (equipped with 2 electric pumps for lubrication and Cooling of the saw blade) is installed in the base. Lodpfoyv Nylsx Anusac - Swarf drawer (can be replaced by a chip conveyor - see Optional) - Preparation for the installation of the minimum lubrication set of the saw blade (Optional), in addition to conventional standard lubrication with emulsion oil. Chip removal brush. - Machine is intended for lifting truck transport. - Bi-metal saw band for solid and profile material.

Condition: new, capacity 90 degrees: round 300 mm capacity 90 degrees: square 250 mm capacity 90 degrees: flat 380x250 mm 260 mm 250 mm 300x200 mm 180 mm 170 mm 200x170 mm 240 mm 210 mm Ljdpeyv Ntrjfx Anueac 280x160 mm dimensions of saw-band 3770x27x0,9 mm 385 mm speed 40/80 m/min total power requirement 1,5/1,8 kW weight 695 kg

Condition: new, 36/72 m/min capacity 90 degrees: round 300 mm capacity 90 degrees: square 260 mm capacity 90 degrees: flat 330x260 mm capacity 60 degrees: round 180 mm capacity 60 degrees: square 170 mm capacity 60 degrees: flat 170x170 mm capacity 45 degrees: round 260/200 mm capacity 45 degrees: square 250/180 mm capacity 45 degrees: flat 270x200/200x160 mm dimensions of saw-band 3650x27x0,9 mm total power requirement 1,5/1,8 kW Overall size 2130x1400x1950 mm Weight 670 kg Semi-automatic function: - Vice closes and engine starts - Saw head lowers for the cut - Engine shuts off - Saw head lifts, vice opens Lsdpfxsyv Nmle Anuoac Semiautomatic dynamic system: Manual lowering of the saw blade to the desired position and cycle start over the hand switch. Upper position is saved automatically.

Condition: new, dimensions of saw-band 4640x34x1,1 mm 15-100 m/min 515 mm capacity 90 degrees: square 320 mm capacity 90 degrees: round 330 mm Laedpfx Aoyv Nkksnujc capacity 90 degrees: flat 510x320 mm 320 mm 320 mm 350x320 mm 230 mm 230 mm 230x310 mm 320 mm 320 mm 380x320 mm 250 mm 250 mm 250x320 mm total power requirement 4 kW Weight 1190 kg Overall size 2000x1200x1800 mm