Used Scm Windor 60 for sale (583)

Condition: excellent (used), Year of construction: 2022, Used edge banding machine - OLIMPIC K 360 R Ltedpfx Asxhc Evoffja - Year of manufacture: 2022 - Available from November 2025 - additional photos/video available

Condition: used, machine/vehicle number: 008132, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt Premilling Unit: yes Corner Rounding Unit: yes Max feed speed: 18 m/min Maximum panel thickness: 60 mm Lodpfxjw Idc Rj Affjta Operating Units: 7 nr

Condition: used, Year of construction: 2021, MEGA 300 TS Numerical Control Panel height 60 mm PVC/Abs mm 3 Feed speed up to 22 m/min Working height adjustable electronically by C.N. Motorized rubber belt with higher pressure Introduction system for small panels Panel support guide with electronic adjustment by C.N. Side roller conveyor with idle wheels for panel support Anti-adhesive group Rectifier unit with two motors electronically adjustable by C.N. Roll holder plate for delicate edges Ltjdpet Hal Defx Affsa Edge magazine with 2 positions Gluing unit for EVA glue with glue tank and pre-melter Edge pressure group on straight profiles with pressure rollers electronically adjustable by C.N Non-stick group Trimming unit with 2 motors with automatic inclination adjustment Trimming unit with 2 superimposed motors Trimming / gleaning group with 2 tilting motors electronically adjustable by C.N. Rounding unit with 4 motors Edge scraper unit electronically adjustable by C.N. Glue scraper unit Oscillating brush group Hairdryer group

Condition: used, Year of construction: 2018, functionality: fully functional, SCM Olimpic K 560 Automatic Edge Gluing, year 2018 for sale! Complectation: Chain feed speed 12/18m/min Edge thickness 0.4/3mm EVA glue Panel milling unit "RT-V" Glue application unit "VC-S4.1" Edge trimming unit "K-SEL" Edge milling unit "R-K" Edge corner rounding unit "ROUND X" Edge scraping unit RAS-K Polishing unit SP-V Ltodpfxsw Sw Tkj Affea Technical characteristic: Conveyor speed (two speeds) m/min 12 - 18 Min / max part thickness mm 8 - 60 Thickness of glued wooden edge mm 0.4 - 6 (8mm HP composition) Thickness of glued roll edge mm 0.4 - 3 Maximum area of ​​glued roll edge mm² 135 Diameter of reel support "plate" mm 780 Maximum overlap of glued edge, relative to the part mm 2+2 Minimum distance between transported parts mm 600 Minimum length of part (when the width of the part is min. 100 mm) mm 140 Minimum length of roll edge mm 180 Minimum length of wooden edge mm 220 Minimum width of the part (when the length of the part is min. 210 mm) mm 95 (60mm opc.) Width of the extension support mm 560 Height of the worktable from the floor mm 900 Plate milling unit "RT-V" Max. chip removal area mm2 55 Max. milling thickness mm 3 Min. / max. thickness of the part mm 8 - 45 (60mm opc. Motor power kW 2 x 1.5 Mill diameter mm 100 Mill height mm 49 (64mm opc.) Tool rotation speed rpm 9000

Condition: ready for operation (used), Technical characteristics Power and Motors Voltage: 400 V Ltodjtu R Sdjpfx Affsa Pluging: Three-phased Overall dimensions Weight: 1428 Kg

Condition: excellent (used), functionality: fully functional, thickness planer SCM S 63 + surface planer SCM F52 + spindle moulder SCM T160 Lodpjvamvysfx Affeta second hand machines in Excellent working conditions NOT separate sale thickness planer model SCM S 63 L'Invincibile useful working width mm. 630 maximum (minimum) working height mm. 240 (3) maximum removal mm. 8 variable feed speed mt./min. 6 ÷ 18 motorized table positioning with reading n.4 knives "Tersa" main motor power Hp 7,5 volt. 380/50 spindle moulder with tilting spindle model SCM T160 L’Invincibile spindle tilting by electric -5 ° / + 45 ° spindle lifting by electric motor power Hp 5,5 shaft diameter mm. 50 volt. 380/50 net weigth kgs. 1000 surface planer model SCM F 52 L'Invincibile working width mm. 520 tables length mm. 3000 ground cast iron tops n.4 knives tilting guide up to 45° motor power Hp 5,5 volt. 380/50

Condition: used, Year of construction: 2005, Working area: X=2970 mm / Y=1725 mm Axis travel speeds: X=60 Y=45 Z=25 m/min Weight: 3200 kg Storage location: Nattheim Ledpfx Ajw Dcccsffota

Condition: used, machine/vehicle number: 008288, Position 1: Panel Feeding and Loading SCM-MAHROS - STEFANI - CELASCHI Position 2: Double Sided Squaring/Edgebanding Machines SCM-MAHROS - STEFANI - CELASCHI Position 3: Panel Turning Device SCM-MAHROS - STEFANI - CELASCHI Position 4: Double Sided Squaring/Edgebanding Machines SCM-MAHROS - STEFANI - CELASCHI Position 5: Panel Turning Device SCM-MAHROS - STEFANI - CELASCHI Lsdpfxjx Nv S Us Affsta Position 6: Splitters SCM-MAHROS - STEFANI - CELASCHI Position 7: Panel Stacking and Offloading SCM-MAHROS - STEFANI - CELASCHI

Year of construction: 2015, condition: ready for operation (used), Main Drive Number of axis 5 Movement X-Axis Movement 3100 mm Z-Axis Movement 160 mm Y-Axis Movement 1550 mm This 3-axis SCM PRATIX 25 CNC Wood Machining Centre was manufactured in 2015. It features a large working area of 3100x1550 mm, a 5-axis milling head, and dual tool changers with 10 and 16 positions. Equipped with a powerful 16.5 hp motor and a vacuum pump capacity of 100 m³, it supports HSK F63 clamping and Xilog Plus software. If you are looking to get high-quality milling capabilities consider the SCM PRATIX 25 machine we have for sale. Contact us for more information. Application Types Ljdpfx Afjx Nr Nisfsta CNC Wood Machining

Condition: excellent (used), Year of construction: 2018, MORBIDELLI M100 CNC Machining Center Working Area X-Y: 3,110 x 1,320 mm Max. workpiece height above suction cups: Z180 mm Technical Data Working range X axis: 3,110 mm * Working range Y axis: 1,320 mm * Panel passage Y: 1,600 mm Panel passage Z: 180 mm Workpiece length for pendulum operation: 1,400 + 1,400 mm Travel speed of X-Y axes: PRO-SPACE: 56 m/min (184 ft/min) Travel speed of X-Y axes: PRO-SPEED: 78 m/min (256 ft/min) PRO-SPACE Safety Devices 1 Enables the machine to be installed without perimeter safety fencing, thereby reducing space requirements. The safety devices are mounted directly to the machine frame. Max. X-axis speed = 25 m/min. 63.03.73 "TECPAD wired" remote control with 7" touchscreen display Tool Changer TRB11 (configuration Y=1,320) Tool Changer FAST14 1 vacuum pump, capacity 250/300 m³/h at 50/60 Hz F31LTC drilling unit The F31LTC drilling head is equipped as follows: Connection for vertical and horizontal drills Ø 10 mm, WELDON type (max drill length = 70 mm) Distance between spindles: 32 mm 21 vertical spindles, selectable independently 5 horizontal drill heads with dual output (one on each side), 3 in X direction and 2 in Y direction Drill spindle speed: 4,500 rpm (with optional inverter 2,500–8,000 rpm) 1 integrated saw blade in X direction (max diameter 125 mm, thickness 2.2–6 mm) Saw blade speed: 5,500 rpm Drilling unit with inverter Pressure booster on the Z-axis 5-axis unit, version "JQX" 10 kW The 5-axis unit includes: HSK 63F tool holder with double reference surface for rigid connection between taper and electrospindle Standard electronic control of rotation speed from 1,800 to 24,000 rpm, with static inverter and quick stop function Continuous power (S1/S6): 8.5/10 kW (11.5/13.6 HP) from 12,000 rpm B-axis rotation: ± 185° B-axis rotation speed: 7,000°/min C-axis rotation: ± 320° C-axis rotation speed: 7,000°/min Right- and left-hand rotation programmable via NC Internal air blast to ensure optimal tool holder coupling Cooling system with circulating fluid and external heat exchanger Ceramic ball bearings on main spindle Internal pressurized air circuit to prevent contamination by dust Surrounding extraction hood for chip removal with pneumatic ON/OFF function Extraction hood for 5-axis electrospindle 6 "TV FLEX" worktables 1,300 Chip and waste conveyor belt for X=3,110 mm 4 loading aid devices H=75 1,300 Front stops H=75 for 6 supports Ledpfxjx Nrwgj Affota Main front reference stop Vacuum suction cups 145x145 mm, H=75 mm – 12 pcs Vacuum suction cups 145x55 mm, H=75 mm, rotatable – 6 pcs Additional hardware dongle for Maestro CNC (for USB port) High-performance PC Location: ex works customer site - Immediately available - System must be dismantled by the seller

Condition: used, functionality: fully functional, planing width: 520 mm, total length: 3,100 mm, total height: 1,500 mm, total width: 800 mm, overall weight: 900 kg, table length: 3,050 mm, planer shaft diameter: 120 mm, working width: 520 mm, number of planer blades: 4, – CE marking – machine as new TECHNICAL SPECIFICATIONS Ltsdpew Iqa Nefx Affoa – max. planing width: 520 mm – cutterhead diameter: 120 mm – 4-knife cutterhead – TERSA knives – noise reduction comb at cutterhead – jointer shaft guard – table width: 51 cm – table length: 305 cm – hydraulic lifting by pedal – height counter – motor: 7.5 kW – tilting fence – manual star-delta switch – extraction port connection: 120 mm – two adjustable tables – quiet operation – full factory cast iron body – original factory paint – dimensions (L/W/H): 310 x 70 x 150 cm – weight: 900 kg

Condition: used, What are Presale Items at Second Owner? Presale items are machines that we sell in their current condition ("as-is"). We have purchased these machines based solely on photos and sell them with the information provided in the advertisement. Unfortunately, we do not have additional details, such as exact dimensions or machine specifications. Additionally, these machines are often not yet in stock and have not been inspected by us. These machines are offered at competitive prices, which means the prices are lower than usual, but the risk lies entirely with the buyer. Please carefully review the information in the advertisement before making a purchase. Ltjdpfx Asx Nigxeffoa If you have any questions, feel free to contact us! - Machine available from: 2026-01-05 - Documentation available: No - CE certificate present: No Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2007, Travel range: X=4400 Y=2195 Z=440 mm Working area in X=3650 mm Y=1560 mm Clearance: 330 mm Electrospindle SCM Power 2000, high speed milling spindle with 13 kW power Rotary axis Vector (C-axis) Cleaning blower for tool on the milling unit Tool holder HSK 63 F Speed range 600 - 24,000 rpm, stepless via inverter Motor power 8.5 kW Tool holders: 6 pcs Tool changer: Rapid 12 (12 positions) Vacuum pump 250 m³/h / 5.5 kW Max. vacuum: 0.9 bar Reference stop at the sides of the table Drilling unit with 11 spindles (7 vertical / 4 horizontal) Control: NUM Series 1000 User interface: XILOG Plus PC Office hardware WINDOWS XP Professional Total connected load: max. 27.5 kW Weight: 5200 kg Storage location: Nattheim Ledpfx Aow Dcb Seffsta

Condition: used, Year of construction: 2012, Basic machine Olimpic K 800 "T-ERL" (47) 1 pc. BASIC EQUIPMENT: - Ribbed steel machine frame with tubular reinforcements for optimal work unit support - Pivoting control panel - Support roller conveyor with ball bushing guides along the entire machine length - Protective and sound-absorbing hood with separate doors between the gluing and finishing units - Extractor nozzles located on the sound-absorbing hood - Electrical system with lockable main switch - Emergency/stop buttons at the inlet and outlet - Inverter for electric spindles. PLATE FEED SYSTEM - Feed chain with rubber glide shoes, mounted on a 1 1/4-inch industrial chain with a high friction coefficient - The chain slides on two guides made of hardened and ground steel, one round and one flat, to guarantee straight feed and protect against lateral misalignment. --- Automatic central lubrication of the feed chain - The upper pressure beam is made of thick-walled steel construction. Complete with double rows of bearing rollers and protective device for the printing rollers - manual lifting of the printing unit with automatic working unit positioning when changing the plate thickness - mech. Digital display for checking the selected panel thickness. ORION 100 CONTROL SYSTEM. Control device complete with PLC, allows fast, easy, and error-free execution of custom processing programs (max. 60 programs). Manages the pneumatic positioning of the units, if present on the machine. (The control system does not include pneumatic positioning). - Alphanumeric keyboard and display - Function keys for quick control of the processing units - Ambient temperature range from 0 to +45° C. MAIN FUNCTIONS - Control of the processing units and automatic activation of the motors - Control and regulation of the glue pot temperature - Selection of longitudinal and transverse processing without program change - Simple and guided diagnostics for easy troubleshooting - Statistics on absolute data and individual processing: number of pieces, edge consumption, total chain feed distance - Unit of measurement selectable in mm or inches. Technical data OLIMPIC K800 T-ER L Edge thickness: 0.4 to 8 mm Max. gluing thickness of the roll edge: 3 mmFeed speed: 12/18 m/minWorking height: 8 to 60 mmMax. dimensions of the edge cut: 135 mm²Turntable diameter: 780 mmMax. oversize compared to the panel thickness: 4 (2+2) mmMin. panel width (with 210 mm min. length): 55 mmMin. panel length (with 100 mm min. width) - with strip or roll edges max. 3 mm: 140 mm - with solid wood edges: 200 mmMin. distance between consecutive panels at 11 (16) m/min: 750 (850) Standard equipment - Pre-milling unit in the infeed RT-E- Gluing station VC-800- Trimming unit KSEL- Flush trimming unit, tiltable RI/800- Rounding unit ROUND K- Scraper unit RAS-V- ½ free space for surface scraper- 1 S free space for surface scraper or Universal milling or buffing unit - 1 free space for air nozzle unit. European safety regulations (C.E. mark). 1 unit. Voltage 400 EU. 1 unit. Frequency 50 Hz. 1 unit. "Autoset" for ER2, T-ERS, and T-ERL models. 1 unit. Allows all necessary adjustments to be made from the control panel for each machining change. Includes: - time-controlled pressure unit - pneumatic and independent pivoting of the mitre saw blades (front/rear) - pneumatic remote adjustment for the RI/800 flush trimming unit. Ltsdexq Apgspfx Affja

Condition: used, Year of construction: 2022, Sliding table: 3200 mm, cutting width: 1000 mm, CNC parallel fence, scoring unit, angle stop with digital display, electro-motorically tiltable and height adjustable, control panel at eye level. Storage location: Nattheim. Lodpexqtvqjfx Affeta

Condition: used, Year of construction: 2023, Exhibition machine Garbsen HORIZONTAL PANEL SAW GABBIANI P Manufacturer: SCM Type: GABBIANI P80 Year of manufacture: 2023 1 unit MAIN FEATURES INDIVIDUALLY SELECTABLE AIR CUSHION TABLES: AN INDISPENSABLE TOOL SIDE SAFETY DEVICES: MORE SPACE FOR WORKING FLOATING GRIPPERS: GUARANTEED PERFECT CUT TECHNICAL DATA GENERAL INFORMATION gabbiani p80 Saw blade projection mm 80 Working table height mm 950 Standard number of grippers 5 Number of grippers for versions 33/38/43 9 / 10 / 10 Number of grippers for versions 33/38/43 with FlexCut 1 unit (single gripper with double fingers included) 10 / 11 / 11 CUTTING DIMENSIONS Version 33 mm 3300x2100 Version 33 (Opt.) mm 3300x3200 Version 38 mm 3800x3200 Version 38 (Opt.) mm 3800x3800 Version 43 mm 4300x3200 Version 43 (Opt.) mm 4300x4300 AXIS SPEED Variable saw carriage speed m/min 6 – 60 Variable pusher speed () m/min 60 MAIN SAW BLADE Motor power (S6 -40%) - 50hz (star-delta start) kW (HP) 7 (9) (11) Speed – 50 hz rpm 4650 Saw blade diameter mm 340 Shaft diameter main saw blade mm 80 SCORING BLADE Motor power (S6 -40%) - 50hz kW (HP) 1.5 (2) Speed – 50 hz rpm 5850 Scoring blade diameter mm 200 Shaft diameter scoring blade mm 80 INSTALLATION Installed power kW 12÷15 Base machine voltage Euro voltage (400 V / 50 hz) Compressed air demand NL/min 300 Required compressed air pressure bar 7 Extraction air requirement m3/h 2440 Extraction air speed m/sec 20 Extraction port diameter mm 4x120 () Note: in countries where EU standards apply, the forward pusher feed speed is limited to 25 m/min. GENERAL CHARACTERISTICS Fully automatic, PC/PLC-controlled horizontal panel saw suitable for cutting solid wood, MDF, chipboard, plywood, and similar materials. Frame and working table – Machine frame is a steel tube construction – Working table of rib-reinforced steel with Bakelite coating – Longitudinal fence on the left side Saw carriage made of steel, consisting of: – a motor for the main saw blade and a motor for the scoring blade – vertical lifting of the saw blade on linear ball bearing guides and shoes – running rollers of hardened and ground steel – balanced mass distribution for optimal cut quality – running direction towards the longitudinal fence – saw carriage drive via rack and pinion – carriage travel on cylinder guides – cylinder guides of hardened and ground steel (5-year warranty), protected by special dust wipers – pneumatic switch for fast and safe main and scoring blade change Pressure beam – pressure beam with uniform pressure across the entire cut length, recesses to prevent collision with grippers; pneumatic height adjustment via high-precision rack and pinion, pressure adjustable from 1.5 to 6 bar – dual extraction system with one unit above the pressure beam for cleaning the work table and one unit below on the saw carriage – side automatic aligner with pneumatic cylinder over the entire length. Sliding on linear ball bearing guides and shoes. * Travel distance: 1200 mm * minimum working width: 60 mm * maximum working width: 1200 mm Positioning pusher and rear part of the machine – Positioning pusher full length, powered by a robust drive shaft. Positioning pusher control... Ltjdpfx Aexyl U Reffea

Condition: used, Year of construction: 2004, Saw unit: pivots 45°. Carriage length: 3200 mm. Maximum saw blade diameter: 450 mm. Saw blade bore: 30 mm. Motor power: 7.5 kW. Max. Cutting width: mm Control panel: at eye level Height adjustment: input via keyboard Tilt adjustment: input via keyboard Tilt angle display: digital Cutting width display: digital Table extension length: yes Cross-cutting at the cross stop: 3200 mm Cross stop display: scale Scoring device adjustment: electric Scoring blade: PSV Protective cover: yes End position lock: yes Automatic motor brake: yes Speeds: 2500/3500/5000 rpm Description: Cutting height at 450 sheets, 150 mm Weight approx.: 1180 kg Dimensions: 3200 x 1800 x 1800 mm Extraction diameter: 1 x 80, 1 x 120 mm Lodpfx Afex Ngzaofeta Storage location: Nattheim

Condition: used, Year of construction: 2016, TECHNICAL DATA AXES Max. workpiece dimensions X-Y-Z mm 3050 x 800 x 50 Min. workpiece dimensions X-Y-Z mm 300 x 90 x 10 Drilling/slotting working area mm 0 x 800/0 x 800 X axis stroke mm 750 Max. travel speed of X-Y axes m/min 25 DRILLING UNIT Vertical spindles Number 7 (4X-4Y one common) Horizontal spindles (along the Y axis) Number 2 (1+1) Horizontal spindles (along the X axis) Number 1 Fixed grooving saw (direction) X Grooving saw diameter mm 100 Max. grooving saw thickness mm 5 Motor power kW (HP) 1.5 (2) Spindle speed rpm 3350 Grooving saw speed rpm 4300 INSTALLATION Power supply V (Hz) 380 / 400 (50 / 60) Installed power KVA 4.5 Compressed air requirement bar 6 Compressed air consumption Nl/cycle 90 Extraction requirement m3 / h 1200 Extraction air speed m / sec 20 Extraction nozzle diameter mm 80+80 F10L Drilling unit Includes: - 7 independent vertical spindles - Drill chuck D10 mm - Distance between spindles 32 mm - 2 horizontal drilling heads, 1 in X direction with one drill, 1 double drilling head in Y direction (1 + 1 drill chuck D10 mm) - Speed 3350 rpm - 1 integrated sawing unit in X (max. Diameter 100 mm) - Saw blade speed 4300 rpm - Motor power 1.5 kW - Vertical pneumatic travel per spindle 70 mm - Horizontal pneumatic travel of the drilling unit. Positioning of the workpiece and drive of the work unit: A CNC-controlled suction cup clamps the workpiece and positions it sequentially under the work unit during machining. Movement in the X and Y axes takes place on THK guides with transmission to reinforced toothed rails. Movement in the Z axis is pneumatically controlled on ball-bushing guides with adjustable stop positioning. The positioning of the work units is carried out using technology and drives with DC motors. CNC CONTROL The control system was specially developed for use in drilling and milling machines. CN - 7" color screen with touchscreen function - Alphanumeric keyboard - Self-diagnosis and any error messages or malfunctions that may occur, in the operator's language Programming - Programming via the CN - Automatic optimization of drilling operations - Option of plate zero point shift - Option of saving and importing drilling programs via USB dongle - Option of importing drilling programs from CAD-CAM external software Configuration - User interface in the same language as the instruction manual Graphic representation of the unit configuration Vacuum suction cups "B-Power Vacuum suction cups with double vacuum connection, recommended for particularly porous panels (e.g. MDF light). Machine user interface software Xilog Maestro USB Hardware and software requirements: - Operating system: Windows XP Professional (SP2), Windows Vista or Windows 7 - Processor: Intel compatible, 2GHz min; Multicore processor recommended - Memory capacity: 1GB min., recommended 2GB - Free disk space: 5GB - Graphic card: Compatible OpenGL (The code includes a DVD for installation and a USB key) Xilog Maestro Features Programming - Parametric, graphic programming - Assisted programming with graphic and syntax help for drilling operations - Possibility to create and save machining macros Integrated additional functions - Self-diagnosis and possible error messages or malfunctions, in the operator's language - User interface in Ljdpfx Ajvvi I Rsffsta

Condition: used, Year of construction: 2018, Startech cn MAIN FEATURES FLEXIBLE AND CUSTOMIZED PRODUCTION COMBINED WITH SPEED AND PRECISION DRILLING FROM ABOVE WITH REFERENCE TO THE TOP OF THE PLATE ALLOWS ABSOLUTELY PRECISION MACHINING NUMERICAL CONTROL WITH 7" COLOR SCREEN: SIMPLE AND INTUITIVE TECHNICAL DATA Startech CN AXES Max. workpiece dimensions X-Y-Z mm 3050 x 800 x 50 Min. workpiece dimensions X-Y-Z mm 300 x 90 x 10 Drilling/slotting work area mm 0 x 800/0 x 800 X-axis stroke mm 750 Max. travel speed of the X-Y axes m / min 25 DRILLING UNIT Vertical spindles number 7 (4X-4Y one of them common) Horizontal spindles (along the Y axis) Number 2 (1+1) Horizontal spindles (along the X axis) Number 1 Fixed groove saw (direction) X Diameter of the groove saw mm 100 Max. thickness of the groove saw mm 5 Motor power kW (HP) 1.5 (2) Spindle speed rpm 3350 Speed of the groove saw rpm 4300 INSTALLATION Power supply V (Hz) 380 / 400 (50 / 60) Installed power KVA 4.5 Compressed air demand bar 6 Compressed air consumption Nl/cycle 90 Extraction demand m3 / h 1200 Extraction air speed m / sec 20 Extraction nozzle diameter mm 120 GENERAL CHARACTERISTICS Universal CNC drilling machine with work table with fixed gantry and movable workpiece for performing the following machining operations: - Vertical drilling on the panel surface - Horizontal drilling on all four sides of the workpiece - Groove Milling with integrated groove saw in the "X" direction. Self-supporting structure. Machine frame made of tubular steel to provide a large base for the work table. The structure is positioned on three self-leveling feet. The electrical control cabinet is integrated into the machine frame. "Easy Motion" central Bakelite support table: - an MDF sector for through-hole drilling, automatically pivoting for horizontal drilling - an infeed roller that facilitates panel loading - a rear roller conveyor that facilitates panel sliding - left and right stops - a central aligner with manual adjustment. The left and right stops are required to drill the two opposite sides of the panel horizontally in the "X" direction. Panel positioning along the X axis is achieved by means of suction cups. Unit support. This is a gantry structure made of tubular steel. The main machining unit is installed on the gantry. F10L drilling unit includes: - 7 independent vertical spindles - Drill chuck D10 mm - Distance between spindles 32 mm - 2 horizontal drilling heads, 1 in X direction with a single drill, 1 double drilling head in Y direction (1 + 1 drill chuck D10 mm) - Speed 3350 rpm - 1 integrated sawing unit in X (max. diameter 100 mm) - Saw blade speed 4300 rpm - Motor power 1.5 kW - Vertical pneumatic travel per spindle 70 mm - Horizontal pneumatic travel of the drilling unit Positioning of the workpiece and drive of the machining unit A CNC-controlled suction cup clamps the workpiece and positions it sequentially under the machining unit during machining. The movement in X and Y axis is carried out on THK guides with transmission on reinforced toothed Movement in Z axis is carried out pneumatically on "ball-bushing" guides with positioning on stop adjustable via the positioning of the working units is carried out via technology and drives with -CONTROL The control was specially developed for use Lsdpfjvwbp Asx Affjta

Condition: used, Year of construction: 2011, Working size in X-direction: 2770 mm Working size in Y-direction: 1220 mm Working thickness (Z-dimension): 80 mm Machine design: Gantry-type machine Main spindle power: 11.0 kW Lodpjvvi Htjfx Affjta Main spindle speed: 1500 - 24000 rpm Vector controlled spindle: Yes Clamping system: HSK 63 F Spindle cooling: Air cooling Number of axes: 3 Tool changer: Yes Tool changer positions: 10 Keyboard: Yes Mouse: Yes Programming system: Xilog Plus DXF interface: Yes Online connection possible: Yes CD-ROM drive: Yes Table type: Matrix table Stop system: Stop cylinders Number of vacuum pumps: 1 Vacuum pump capacity: 250 m³/h Safety: Safety tread mats Storage location: Sonnefeld

Condition: used, Year of construction: 2004, Storage location: Nattheim Ltodpfjvvi Hyex Affea

Condition: used, Year of construction: 2020, CNC-CONTROLLED MACHINING CENTER WITH MULTIFUNCTIONAL TABLE - WORK CELL VERSIONX400 CELLDrilling and milling made for you!The numerically controlled machining center is equipped with a wide range of milling/drilling tools to meet every need in the processing of wood and similar materials.- More powerful, with drilling spindles with 8,000 rpm and . Technology, the toughest spindle available on the market, with over 1,000 maintenance-free hours of use. Better and more comprehensively equipped, with various configuration options thanks to the multifunctional table to optimally equip the machine according to your needs. Easier and more understandable programming thanks to the integrated MAESTRO CNC CAD-CAM module. Easier to use: the work table is accessible at all times, the electrical cabinet and vacuum pump are integrated, and in the PRO SPACE configuration there are no guards. Supporting structure. The supporting structure consists of a particularly strong monolithic steel base, heavily ribbed and very rigid. The particularly wide support was specifically designed to give the machine stability, ensuring consistent precision regardless of the working conditions and eliminating the need to anchor the machine to the floor. The base forms a large and solid support for the mobile column: the work unit is thus equipped with a balanced, stable, and durable support that can withstand the most extreme stresses, ensuring higher quality performance and greater precision. The mobile gantry consists of a single, solid unit anchored to the base on both sides and slides on pyrotechnic guides with top-quality ball-return slides. The dual motorization along the X-axis ensures top performance even under demanding working conditions. The movement of the lower moving unit (X-axis) and the working unit along the rod of the moving unit (Y-axis) is achieved thanks to a rack/pinion transmission with helical teeth. this creates a greater tooth-to-tooth thrust which achieves greater acceleration and greater speed along the X and Y axes. The specially designed helical gearing ensures less wear on the mechanical components and less noise. The vertical Z axis is driven by a screw with ball return which ensures perfect balance with dynamic loading and strong acceleration and deceleration. The main milling unit is directly coupled to the Z axis carriage and ensures absolute quality of finishes as any vibrations are completely eliminated. Translation along the X-Y-Z axes is carried out by brushless motors driven by static inverters; These ensure: - Reduced processing times thanks to improved acceleration - Better positioning accuracy thanks to the high-resolution encoder - Zeroing of setup operations when switching on the machine thanks to absolute encoders - Zeroing of general maintenance operations since there are no brushes with the "brushless" system The management of the axis displacement and, in general, of the machine's working elements is carried out by an industrial NS module with digital D Ltjdpevvi N Isfx Affoa

Condition: used, Year of construction: 1999, Storage location: Nattheim Lsdpjvvi Rxjfx Affota

Condition: used, Year of construction: 2019, Incl. tools CNC-CONTROLLED MACHINING CENTER morbidelli m100 Drilling and milling made for you! This numerically controlled machining center is equipped with a wide range of milling and drilling tools to meet every woodworking requirement. - Highly powerful - with 8,000 rpm drilling spindles and . technology, the most stable spindle available on the market, with more than 1,000 maintenance-free hours of use. - Optimally and comprehensively equipped - the vacuum cleaners can be individually configured with the TV FLEX work table to customize the machine to meet individual requirements. - Easy and understandable programming thanks to the integrated Cad-Cam MAESTRO CNC software - Easy to operate; the lowered machine frame makes the work table accessible at all times. The control cabinet and vacuum pump are integrated into the machine bed, and in the PRO SPACE version, no additional structural protective measures are necessary. Supporting structureThe supporting structure consists of a particularly strong monolithic steel base, ribbed and very robust. The particularly wide support was specifically designed to give the machine stability, ensuring constant precision in all working conditions. The machine does not need to be anchored to the ground. The base provides a large and solid support for the mobile column: the work unit is equipped with a balanced, stable and resistant support that can withstand the most extreme stresses, ensuring superior performance and greater precision. The mobile gantry consists of a solid single part anchored to the base and the work unit is fixed to it and moves along Y and Z axes, also on prismatic guides with ball return sliding blocks of the highest quality. The movement of the lower moving unit (X-axis) and the working unit along the crosshead of the moving unit (Y-axis) is achieved thanks to the power transmission via a rack and pinion with helical teeth; This creates a greater tooth-to-tooth thrust, which achieves greater acceleration and higher speed along the X and Y axes. The specially designed helical gearing ensures less wear on the mechanical components and less noise. The vertical Z axis is driven by a screw with ball return, which ensures perfect balance with dynamic loading and strong acceleration and deceleration. The main milling unit is directly coupled to the Z axis carriage and ensures very high quality finishing as vibrations are completely eliminated. Translation along the X-Y-Z axes is carried out by brushless motors driven by static inverters. These ensure:- Reduced machining times thanks to improved acceleration- Better positioning accuracy thanks to the high resolution encoder- Elimination of setup operations when switching on the machine thanks to absolute encoders- Elimination of general maintenance operations as there are no brushes with the "brushless" systemThe management of the axis displacement and in general of the working elements of the machine is done via e Ledpsvvi Scjfx Affsta

Condition: used, Storage location: Nattheim Lsdjwkirqspfx Affeta