Used Sandblasting Machine for sale (65,028)

Condition: used, machine/vehicle number: 005521, X axis working area: 4000 mm Y axis working area: 1400 mm Working Table: Pod and Rail Main Electrospindle power: 15 KW Number of controlled axes: 4 axes Kdsdpfx Ahsvctlgsbju Total number of drilling spindles: 30 Total number of tool changer positions: 24

Condition: as good as new (ex-display), Year of construction: 2025, KraussMaffei KM 651-6100 GX hydraulic injection molding machine LRX 250 robot Year of manufacture: 2025 TECHNICAL DATA Manufacturer: KraussMaffei Year of manufacture: 2025 Clamping force: 6500 kN (650 tons) Machine type: hydraulic injection molding machine Robot: KraussMaffei LRX 250 CLAMPING UNIT Clamping force: 6500 kN (650 t) Mold opening force: 455 kN Platen dimensions: 1660 × 1530 mm Tie bar spacing: 1200 × 1020 mm Mold opening stroke: 1450 mm Minimum mold height: 450 mm Maximum mold height: 1000 mm Maximum platen clearance: 1900 mm Ejector stroke: 300 mm Ejector force front/rear: 140/70 kN INJECTION UNIT Screw diameter: 95 mm L/D ratio: 23.0 Injection pressure: 1795 bar Injection volume: 3367 cm³ Injection shot weight: 2391 g (HDPE) Injection speed: 110 mm/s Injection rate: 780 cm³/s Screw speed: 147 rpm Plasticization rate: 102 g/s Nozzle closing force: 166 kN ELECTRICAL AND HYDRAULIC SYSTEM Pump motor power: 97 kW Installed heater power: 54 kW Number of cylinder heating zones: 7 Dry cycle time according to Euromap 6: 3.3 s / 840 mm Dry cycle time according to KraussMaffei: 2.9 s / 600 mm Oil tank capacity: 1435 l DIMENSIONS AND WEIGHT Kdsdps Aaxp Sjfx Ahbou Machine length: 10,190 mm Machine width: 3030 mm Machine height: 2510 mm Net weight: 38,500 kg KRAUSSMAFFEI LRX 250 ROBOT Manufacturer: KraussMaffei Model: LRX 250 Type: linear robot, 3-axis Payload: below 25 kg (including gripper and part) X-axis – stroke from mold: 900 mm Y-axis – vertical stroke: 1000/1000 mm, telescopic Z-axis – transverse stroke: 2500 mm Axis drives: servo motors Vertical axis: equipped with a motor brake Part removal side: opposite to the operating side

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, DMU90P duoBLOCK Operating hours: 52,700 h Operating hours: 22,700 h Kjdpfx Ahj Aa Ayujbsdu Immediately Available! Control: HDH iTNC640 Travel: X-900 mm, Y-1050 mm, Z-850 mm clamping surface: 900 x 700 mm max. table load: 1.800 kg Spindle mount: SK50 Spindle speed: 12,000 rpm tool magazine: 60 seats Internal coolant supply (IKZ) and chip removal package: 40 bar Tool measurement: BLUM Laser probe: Heidenhain electric handwheel: Yes

Condition: used, machine/vehicle number: 005448, Max. panel width: 3000 mm Kdodpfx Ahowcydzjbsu Max. panel length: 1350 mm No of injectors: 24

Condition: used, machine/vehicle number: 007350, X axis working area: 4000 mm Y axis working area: 1400 mm Working Table: Pod and Rail Kdedpfx Ahj Aayaljbju Main Electrospindle power: 15 KW Number of controlled axes: 4 axes Total number of drilling spindles: 30 Total number of tool changer positions: 28

Condition: used, machine/vehicle number: 008403, Max. machinable height: 160 mm Kodpfx Ajykivhehbsdu Maximum machinable width: 250 mm Max. forward feed speed: 24 m/min Operator shafts number: 5

Condition: used, machine/vehicle number: 007468, X axis working area: 3200 mm Y axis working area: 1300 mm Main Electrospindle power: 11 KW Number of controlled axes: 3 axes Total number of drilling spindles: 36 Total number of tool changer positions: 10 Ksdpfxo Aax Nfj Ahbsdu

Condition: used, Year of construction: 1990, functionality: fully functional, weight 4 t X - Y + Z-axis each 410 mm kN control Fanuc Axis 4 Kedpjuu S R Ujfx Ahbedu

Condition: used, Safety fencing for securing machinery or areas. Technical data: Kjdozryz Ajpfx Ahbjdu - Colour: Yellow - Length: 4,000 mm - Height: 1,700 mm

Condition: used, Year of construction: 2000, functionality: fully functional, pointing milling machine für Stangen carbide turnover plates 4 Stück working area Rund, Profil+vierkant mm working range 80 (100) an 25 mm milling drive 380/420V, 18,5 KW, 50 Hz kW revolutions per minute Fräsantrieb: 1465 U/min . clamping devices hydraulic pneumatic hydraulisch infeed device hydraulisch ca. 5 lfdm x 300 mm hydraulic power unit Rexroth tank 250 l coolant tank mit Spänekasten l switchgear cabinet mit Klimaanlage control SIEMENS S 7-300 +++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Ksdsg Akgtspfx Ahbsdu Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. +++++

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 161055, Used ENGEL injection molding machine Manufacturer: ENGEL Type: INSERT 330V/100 Kjdpfx Ahe Aazd Sjbsdu Year of manufacture: 2006 Machine No.: 161055 Weight: 9400 kg

Condition: good (used), Year of construction: 1998, Good working condition. Parts shown by hand not come. Kdsdpfx Ahe Aaz Rxobsu Technical data are shown on picture.

Condition: new, Benchtop drill press OPTIMUM D 23 Pro-Set OPTIdrill - Exhibition model - ----- Technical data ----- Number of speeds: 12 steps, Speed range: 200 - 2,440 rpm, Spindle stroke: 80 mm, Arm reach: 180 mm, Table size: 280 x 245 mm, Max. drilling capacity in steel: 25 mm, Motor: 750 watts, Column diameter: 73 mm, Dimensions (L x W x H): 615 x 330 x 1,015 mm, Weight: 63.5 kg, Spindle mount: MK 2 Benchtop drill press with V-belt drive - Industrial motor - User-friendly safety switch according to IP 54 - Digital depth-of-drill and speed display integrated into the housing - Separate emergency stop switch - Precision-bored spindle - Safety electrical system in 24 V DC - Guaranteed concentricity accuracy less than 0.02 mm, measured in the drill chuck - Drilling spindle with precision ball bearings - High-quality quick-change drill chuck - Depth stop - Precisely machined, stable drill table with diagonally running T-slots and a surrounding coolant channel - V-belt cover with safety switch - One-piece, die-cast aluminum spindle lever with soft-grip handles - Large, height-adjustable protective shield with safety switch - Heavy-duty design of the entire machine - GATES quality belts - Right/left rotation -- Scope of supply -- Quick-change drill chuck 1 - 16 mm Morse taper MK 2 / B16, T-slot wedges Kjdpfx As Aaz Ttehbjdu Special set including machine vise BMS 100 - New exhibition model -

Condition: used, operating hours: 14,808 h, total height: 2,850 mm, total length: 9,000 mm, total width: 2,450 mm, Year of manufacture: 2006 Colour: White Empty weight: 4.000 kg - Machine available from: 2026-07-10 - Year: 2006 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Serial number: AA1/015406 - Operating hours: 14808 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - - Min. spindle speed [rpm]: 600 - - Max. spindle speed [rpm]: 24000 - - Main motor power [kW]: 11 - - C-axis present: Yes Kodpfx Aj Aazv Ushbjdu - Type milling table: Beam table - Tool holder: HSK-F63 - Material clamp system: Pneumatic - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 12 - Saw unit present: Yes - Tool changer positions [pcs.]: 16 - System/software: Xilog plus - Safety feature: Safety mat - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - └ Main motor power [kW]: 5.5 - └ Capacity [m³/h]: 250 - CNC options: Manual control, Offcut conveyor - CNC documentation available: User keys/licenses - Table length [mm]: 3050 - Table width [mm]: 13 - Working range X [mm]: 3110 - Working range Y [mm]: 1300 - Z-axis working range [mm]: 200 - X-axis maximum stroke [mm]: 3500 - Y-axis maximum stroke [mm]: 1815 - Z-axis maximum stroke [mm]: 440 - Installed length [mm]: 4600 - Installed width [mm]: 6500 - Installed height [mm]: 3400 - Transport dimensions: 9000mm x 2450mm x 2850mm (l x w x h) - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Year of construction: 2005, travel distance X-axis: 16,000 mm, travel distance Y-axis: 3,500 mm, travel distance Z-axis: 1,500 mm, Head Pick up Station TUPC CNC Indexing Micro Head A-Axis 360.000 x 0,001 Gr C-Axis 360.000 x 0,001 Gr SELS Spindle extionsion L=500 mm CTS Internal coolant system ATC Chain Tool changer 60 Positions Hydrostatic guideways Optional T Slotted floorplates 5600 x 1875 (2x) + 4000 x 1875 mm Kedpfx Ahjxpfkkebedu X-Axis: 16.000mm Y-Axis: 3.500mm Z-Axis: 1.500mm Power on spindle: 80kW Spindle speeds: 4000Rpm Spindle Taper: Sk59ISO/Bt/Mk Feed rate X-Axis: 25000mm/min. Feed rate Y-Axis: 25000mm/min. Feed rate Z-Axis: 25000mm/min. Millinghead auto-index:2.5 x 2.5° Length: 24000mm Width: 6500mm Height: 6500mm Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1990, Hydraulic surface grinding machine with automatic vertical feed Max. grinding length 670 mm Max. grinding width 280 mm Max. grinding height 400 mm Table speed, longitudinal 2 – 35 m/min Table speed, transverse 0.3 – 40 mm/stroke Rapid traverse yes Grinding wheel dimensions 300 / 76 x 40 mm Drive power 4 kW Machine dimensions L x W x H 2000 x 1850 x 2000 mm Machine weight 2300 kg Hydraulic and electrical system dimensions L x W x H 1200 x 800 x 2000 mm Hydraulic and electrical system weight 650 kg Accessories / Special features: • Permanent magnet clamping plate 630 x 200 mm • Automatic vertical feed with digital display • Manual dressing device • Coolant system • Separate hydraulic unit • Grinding wheel • Machine alignment elements Note: o Hydraulic cylinder for table stroke newly sealed Ksdpfof Um Rasx Ahbsdu o New filters in the hydraulic unit o Handwheel adjustment for transverse stroke newly mounted Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Condition: excellent (used), Year of construction: 2008, Table size 600 x 300 mm Max. grinding area 600 x 300 mm Dimensions of the grinding wheel 406 x 50 x 127 mm Min. / max. distance table / spindle center 500 mm Table speed, hydraulically adjustable 5 - 25 m/min. Cross feed 0.1 – 20 mm Cross travel 900 mm/min. Handwheel, cross 1 revolution 5 mm 1 division mark 0.02 mm Automatic vertical feed 0.001 - 0.999 mm/cycle Handwheel, vertical 1 revolution 2 mm 1 division mark 0.01 mm With AD 5 (automatic feed) 0.005 mm Grinding motor speeds 1450 / 2900 rpm Grinding motor 1.5 / 3.7 kW Hydraulic pump motor 0.75 kW Drive motor, cross 1.1 kW Drive motor, vertical 1.1 kW Machine dimensions L x W x H approx. 2300 x 1800 x 2100 mm Weight 1700 kg Accessories / Special features: • 2-axis digital display • Automatic vertical feed with spark-out and subsequent retraction • Electro-magnetic clamping table L x W 600 x 300 mm • Manual grinding wheel dressing device • Grinding wheel speed, 2 stages Kodpfxoizka Ij Ahbedu • 1 grinding wheel with flange • Control panel • Lighting • Coolant system with band filter and magnetic separator • Machine feet • CE compliant Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 11-153 DE - 44143 Dortmund - Wambel / Germany

Condition: excellent (used), Year of construction: 2011, Table size: 1800 x 800 mm Tool holder DIN 69871: ISO 40 Travel ranges: X-axis: 1615 mm Y-axis: 815 mm Z-axis: 725 mm Table load: 2000 kg Spindle speed range: 0 - 10,000 rpm Feed rate: up to 10 m/min Rapid traverse: 24 m/min Footprint (W x D x H): approx. 5400 x 4550 x 3120 mm Drive power: 15 / 18.5 kW Weight: 10,000 kg Accessories / Special features: • CNC control system FAGOR 8055 i/PLUS MS • Internal coolant supply through the spindle, 20 bar • 24-position tool changer • Hinged chip conveyor • Coolant system • CE compliant Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany Kedeyy Npnspfx Ahbsdu

Condition: good (used), Year of construction: 1992, Table surface area: 1850 x 710 mm Permissible table load: 3000 kg Travel ranges: Longitudinal, automatic (X): 1600 mm Lateral, automatic (Y): 710 mm Vertical, automatic (Z): 850 mm Spindle mounting: SK 50 Speed range: 20 - 2500 RPM Main motor power, AC: 15 kW Transport dimensions L x W x H: 3650 x 2300 x 2700 mm Weight: 9400 kg Kodpfx Aettamkehbodu Accessories / Special features: • CNC path control system, manufacturer HEIDENHAIN, model TNC 360 with 3 scales • Programming language "Plain text dialog" and DIN-ISO • Electronic handwheel HEIDENHAIN HR 330 with magnetic holder • 3D probing system HEIDENHAIN TS 120 • Main spindle compact unit RAC 3 • Control system prepared for 4th axis • Universal milling head system "HURON" with 2 levels, gears run in an oil bath • Hydraulic tool clamping • Coolant system • Central lubrication with interval • German electrical system, drives INDRAMAT • Operator control panel • Operating manual - Newly refurbished milling head, partially overhauled with new gears, seals and bearings - Oil dispenser for central lubrication renewed Operating hours: 10,032 Program runs: 3,288 Spindle ON: 2,569 Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE – 44143 Dortmund - Wambel / Germany

Condition: excellent (used), Year of construction: 2016, Travel paths X / Y / Z 300 / 200 / 200 mm Max. table load: 16 kg Kdsdpfx Ajt E Hd Rshbeu Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund-Wambel / Germany

Condition: good (used), Year of construction: 1991, Table clamping surface: 710 x 400 mm Tool holder: ISO 40 Travel paths: X-axis: 400 mm Y-axis: 350 mm Additionally displaceable in Y-axis: 420 mm Z-axis: 380 mm Quill stroke: 80 mm Speed range: 45 – 2240 rpm Feed range, stepless: 6.3 – 1250 mm/min Rapid traverse: 1250 mm/min Drive power: 2.2 / 2.8 kW Dimensions (L x W x H): 1400 x 1600 x 1850 mm Weight: 1900 kg Accessories / Special Features: • 3-axis digital readout by HEIDENHAIN • Vertical and horizontal milling spindle • Vertical milling head with quill, tiltable right and left • Stepless feed • Rapid traverse on all 3 axes • Fixed angle table • Coolant system • Chip tray • Spindle clamping by push button, e.g., for tool change • Machine feet • Central lubrication • Control panel • Emergency stop switch Kjdpsupiypofx Ahbsdu Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: reconditioned (used), Year of construction: 2013, functionality: fully functional, CNC vertical machining center "KUNZMANN BA 1000 SK" Equipped with Heidenhain iTNC 530 path control. Year of manufacture: 2013 Travel ranges: X 1020 mm, Y 620 mm, Z 920 mm Spindle speed range: 1 – 14,000 rpm, stepless With the following accessories: - Fixed angular table, 1200 mm x 610 mm clamping surface Kedpoyx Ua Aefx Ahbodu - NC attachment rotary table WALTER, diameter 500 mm - B-axis swivel head (torque drive), +30 / -120 degrees - Vertical tool changer with 40 magazine positions (SK 40) - 3D Heidenhain touch probe - Electronic handwheel - Fixed full enclosure with internal lighting - Coolant through spindle (IKZ system) - Coolant system - Oil mist extraction - Chip conveyor - Operating manual

Condition: used, total width: 800 mm, total length: 1,200 mm, total height: 2,600 mm, Year of manufacture: 1987 Colour: Green Empty weight: 700 kg - Year: 1987 - Serial number: 14441 - Drive system: Conventional - Drive system: Gear drive - Power [kW]: 2.2 - Table type: Fixed table - Table length [mm]: 500 - Table width [mm]: 500 - Drilling depth [mm]: 250 - Drilling capacity [mm]: 32 - Reach [mm]: 320 - Tool holder: MK4 - Main spindle power [kW]: 1.5 - Min. spindle speed [rpm]: 85 Kdedpfx Aozkq Auehbeu - Max. spindle speed [rpm]: 1500 - Options: Drill unit feed - Transport dimensions: 1200mm x 800mm x 2600mm (l x w x h) - Transport weight [kg]: 700kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Year of construction: 1991, operating hours: 19,888 h, condition: used, Year of manufacture: 1991 Operating hours: 19.888 - Year: 1991 - Documentation available: No - CE certificate present: No - Serial number: 1844 - Operating hours: 19888 - Control: CNC Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum Kdedpfx Aozldwbshbsu

Condition: good (used), Schmedt hardcover book production line The machines are in very good condition and have seen little use. The set consists of the following machines: Kdsdpfxez S Uzij Ahbju – Schmedt PraLeg book block casing-in machine – Schmedt PraForm Pro book press and joint-forming machine – Schmedt SC-3 Autocase cover assembly table – Schmedt PraziCoat Pro gluing machine (coater) – Schmedt BT-1 Board Trimmer (automatic board cutter) Includes documentation, spare parts, and glue.