Used Route Control for sale (47,610)

Year of construction: 2017, condition: used, Used machine Year of manufacture: 2017 Condition: Well-maintained Equipment: Gantry milling machine High-Z S-1400T/105 (Rev. 1.5 - Facelift 2016) with ball screws Travel: 1400 x 1050 x 110 mm (X/Y/Z) Machine control Zero-3 (Rev. 1.3) for High-Z series, 5-channel, 110 - 240 Volt, 50/60 Hz Milling kit for High-Z S-1350 or S-1400T/105, additional stabilization of the Z-axis when machining very hard materials Energy arm for S-1350 and S-1400/105 Cable harness for clean routing of cables and hoses from milling motor, spray mist cooling, etc. T-slot plate on base frame for High-Z S-1400T/105 - 1790x1160mm (NL2016) 1790 x 1160 x 76mm T-slot keys, 8 pcs with bridge, M6 - 10 pcs. incl. screws M6x25 6 pcs. clamping bars 50x20x10mm M6 Base frame for combination with enclosure for S-1400T/105 - 1790x1450x900mm (NL2016) SET - Suhner milling motor UAD 30-RF / 1050W - 3,500-30,000 RPM, 230 Volt, 50/60Hz incl. 8mm and 10mm collets Collet set for Kress and Suhner (UAx-30RF) milling motors, 3.00mm / 3.175mm (1/8") / 6.00mm Milling cutter set, 10-piece (shaft 3.175mm) Wood milling cutter: 2x1mm / 2x2mm / 1x3mm Aluminum/plastic: 2x1mm / 2x2mm / 1x3mm Extraction nozzle made of aluminum for Kress or Suhner milling spindle Hose nozzle with Ø 32 and 38mm Dimensions 135x60x30mm Tangential module EOT-3, stroke 3mm Oscillating with 3mm stroke Connection cable for EOT-3 / TCM-4 for High-Z series - 5m Tungsten carbide blade type E12 - cutting edge 12mm Tungsten carbide blade type E18 - cutting edge 13.5mm EcoCam EC-4 continuous cutting pad 4mm / roll width 2m Always delivered in 2m roll width!!! 1m2 = 2 x 0.5m Tangential grooving module TCT-1 Tool holder type KR for grooving module TCT-1 for ball-bearing grooving wheels Grooving wheel B14 Grooving wheel B24 Side channel compressor Rubin 220, 1.5KW/50Hz vacuum pump incl. 3m spiral hose 40mm 230V/50Hz / 9.5A / 190mbar -190mbar / 71dB(A) Maintenance set High-Z series Grease gun + grease cartridge 400g + 100ml oil Network switch 5-port 10/100 Mbit/s + LAN cable 1m, 5x 10/100Mbps-RJ45 ports with auto negotiation Kinetic-NC control software incl. CNC-Pod (LAN), network cable + USB charging cable Vacuum table VT-150100 - 1500x1000mm incl. through-milling mat and connecting hoses Kodpszu T Smsfx Ah Eedt Location: NRW Availability: Short-term Sold on behalf of a customer! Technical data without guarantee!

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, operating hours: 12,666 h, power: 12 kW (16.32 HP), MACHINING CAPACITIES: - X-axis (U) vertical milling travel: 3875 mm, 3170 mm between stops - Y-axis (V) milling travel: 1390 mm between stops, for drilling: 1201 mm - Z-axis (W) milling travel: 290 mm Maximum workpiece height (thickness), effective travel: 110 mm For further details, see aggregate travel schematic - Maximum traverse speeds: X-axis (U): 60 m/min Y-axis (V): 50 m/min Z-axis (W): 20 m/min MACHINE CONFIGURATION: - Worktable with 6 mobile support beams, equipped with several vacuum pods and pneumatic clamps 2 pneumatic connections per beam for clamps, usable capacity ranging from 44 to 78 mm 6 rear stops 6 intermediate stops 3 right lateral stops 3 left lateral stops 4 lifting blades (for loading/unloading assistance) Kodjy Nb Tkopfx Ah Ejdt Table divided into 2 working zones - Becker VTLF vacuum pump 250 m3/h, 5.5 kW with air filter - Pfannenberg cooling unit 1.7 kW - Chip conveyor belt - X-axis movement by rack and pinion, Y & Z axes by ball screw and bearing block (high-precision linear guides with automatic lubrication) - Aggregates on swan-neck, composed as follows: • 12 kW HSD milling/routing unit - Toolholder type: HSK 63 F - Variable spindle speed 6000 - 24000 rpm - Inverter-controlled - Surround extraction hood - Onboard tool magazine with 10 stations + additional 12-station magazine • 11-spindle drilling unit, 1.7 kW - Center distance between spindles: 32 mm - Spindle speed: 4000 rpm - 11 vertical spindles (8 along X, 3 along Y) - 2+2 horizontal spindles on X - 1+1 horizontal spindles on Y • Control panel - Windows PC - Network card and Ethernet connection - Software: Masterworks and user manual - DXF conversion and direct execution of ISO, TLF, DXF - Pre-programmable zones - Remote control OTHER FEATURES: - Overall electrical supply: 400V, 3Phases+N+E, 50Hz Nominal current: 58.6A, 46.6 KVA - Pneumatic supply: 7/8 Bar - Average consumption: 100Nl/min - Extraction Lower port Ø120 mm, upper port Ø250 mm Recommended flow rate: 6500 m3/h at 20 m/s - CE certified, safety zones and protective grille Lockable isolator, emergency stops Operating footprint: see schematic Transport dimensions: to be specified during equipment preparation Estimated total weight: 2400+350+350 kg Please contact us for supply of consumables, accessories and/or extraction systems. Original documentation, manual, spare parts list, electrical and pneumatic diagrams, service keys, software and license keys included.

Condition: new, Year of construction: 2015, Complete Knapp Fastline System RA2519 _____ Premium Conveyor Technology Available Immediately A high-quality, modular conveyor system from the Austrian intralogistics specialist KNAPP AG is for sale. The system was manufactured in 2015 as part of an automated material flow system but was never put into operation. It remains disassembled and in storage today. With a conveyor length of approximately 300 meters, numerous buffering sections, RollerDrive curves, and comprehensive original documentation, this system offers a cost-effective alternative to a new, expensive purchase. _____ The system at a glance Feature Description Manufacturer KNAPP AG System Fastline Year built 2015 Conveyor Length approx. 300 m Roller Width 450 mm Accumulation space 720 mm Kedpfezwylrox Ah Esdt Conveyor speed 0,75 m/s RollerDrive curves 11 units Interroll DriveControls 277 units available _____ High-quality industrial design The KNAPP Fastline series is one of the proven modular conveyor systems for automated material flows. The system was developed for the continuous transport of cartons and containers and is suitable for use in: • Distribution centers • Shipping logistics • Production logistics • E-commerce • Replacement or expansion of existing conveyor systems Thanks to its modular design, individual conveyor sections can be used just as easily as complete system components. _____ Scope of Delivery The scope of delivery includes, among other things: Conveyor Technology • Approx. 300 meters of roller conveyor systems • Accumulation roller conveyors • Drive roller conveyors • Conveyor modules of various lengths • Conveyor curves Curves • 11 RollerDrive curves Drive Technology • 277 Interroll DriveControls EC310 Steel Structures • Extensive support columns • Column bases • Connecting elements Pneumatics • Pneumatically controlled accumulation stations • Pneumatic assemblies • Sensors Documentation • Original KNAPP parts lists • Transport and package lists • Documentation of the main assemblies _____ Technical Concept The system is based on the modular KNAPP Fastline system. The material being conveyed is transported on roller conveyors. The storage bins are pneumatically controlled. Thanks to the modular design, conveyor routes can be easily extended or adapted to new warehouse layouts. A key advantage is the use of commercially available industrial components, ensuring that replacement parts will remain available in the future. _____ Premium Manufacturer KNAPP is one of the world\'s leading manufacturers of automated material flow systems. The system is not a custom-built or specially designed solution, but rather based on an industrial mass-production platform. _____

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, operating hours: 15,396 h, pressing force: 173 t, stroke length: 500 mm, overall weight: 16,000 kg, working length: 4,250 mm, Equipment: CE marking, full service history, No minimum price – guaranteed sale to the highest bidder! TRUMPF TruBend 5170 including BendMaster! The machine has been continuously serviced and maintained by Trumpf, with a complete service record. The cylinders are leak-proof and have no oil loss. The tools shown for the robot are included. TECHNICAL DETAILS Stroke: 500 mm Press force: 1,700 kN Working length: 4,250 mm Tool clamping: Hydraulic, top and bottom Number of axes: 6 Load capacity: 60 kg MACHINE DETAILS Voltage: 3 x 400 V Rated current: 41.0 A Frequency: 50 Hz Connected power: 28.0 kVA Control voltage: 24 V DC Follow-up time: max. 90 ms Follow-up distance at 220 mm/s: max. 10 mm Follow-up distance at 160 mm/s: max. 8.5 mm Operating pressure: max. 300 bar Weight: 16,000 kg Operating hours Press beam running time: 15,396 h Hydraulic system running time: 83,212 h Machine operating hours: 152,638 h EQUIPMENT CE marking Documentation/Manual Rear stop with sensors CNC crowning Bendmaster (robot with 8 m travel) Vacuum manipulators CNC gripping station Double sheet detection Kjdezzkvcepfx Ah Eedt BendGuard laser safety device Spare parts: Cable carrier, spare vacuum plate, BWF fixators (machine feet) The height and weight of the asset must be taken into account when selecting the transport vehicle. A forklift is available for loading. If collection is not completed within the specified timeframe, a storage fee of €20.00 per lot and for each day started will be charged. The fee must be paid before collection. The sale is made with the exclusion of any warranty or guarantee. The information on the technical data comes from the original offer. No guarantee is given for typographical or measurement errors. In case of doubt, please compare the information with the provided photos or inspect the goods on-site before the end of the auction.

Condition: excellent (used), Year of construction: 2005, machine/vehicle number: 20787, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, IMA BIMA 410 V 140/600 – Professional CNC Woodworking Machining Centre. The machine features a gantry construction and is designed for the production of furniture, stairs, and special components. The large Z-axis travel (600 mm) enables machining of high workpieces. It is equipped with a 7.5–11 kW spindle, automatic tool changer, vertical and horizontal drilling heads, and a vacuum table with consoles. Controlled by IMA WOP. Manufacturer: IMA (Germany) Model: BIMA 410 V 140/600 Type: CNC Machining Centre for Wood (point-to-point) 🧩 Working Area • X-axis: up to approx. 6000 mm • Y-axis: approx. 1400 mm • Z-axis: version 140 / 600 mm (high Z-axis – large clearance) • Number of axes: 3–5 (depending on configuration and head) ⚙️ Main Spindle • Power: 7.5 – 11 kW • Speed: 1,500 – 24,000 rpm • Tool holder: HSK F63 • Max. tool diameter: approx. 100–150 mm • Max. tool length: approx. 150 mm • Max. tool weight: approx. 6 kg 🔧 Tool Magazine • Automatic tool changer • Number of positions: 18 🪚 Working Units (typical) • Vertical drilling heads: up to 21 spindles • Horizontal (cross) drilling heads • Special aggregates (optional): • Lock case routing units • Grooving saw • Blum/Lamello hardware aggregates • Angular aggregates 🧲 Worktable • Pod & rail vacuum table (consoles) • Approx. 8 working consoles • Vacuum pumps: 2 units (approx. 100–140 m³/h) ⚡ Drives and Feed Rates • Rapid traverse: • X: up to approx. 100 m/min • Y: up to approx. 80 m/min • Z: up to approx. 25 m/min 💻 Control • CNC: IMA WOP / IMAWOP (optionally Siemens / Beckhoff) ⚙️ Installed Power • Total connected load: approx. 23 kW 📏 Machine Weight Kedpfx Ahoyky Hds Eodt • approx. 6,500 – 8,500 kg (depending on configuration)

Condition: used, Year of construction: 2019, operating hours: 2,294 h, functionality: fully functional, machine/vehicle number: 0-250-71-6845, feed length X-axis: 3,050 mm, feed length Y-axis: 850 mm, feed length Z-axis: 70 mm, feed rate X-axis: 50 m/min, feed rate Y-axis: 50 m/min, feed rate Z-axis: 15 m/min, working width: 850 mm, total width: 1,984 mm, total length: 2,920 mm, total height: 1,895 mm, We offer a well-maintained HOMAG DRILLTEQ V-200 vertical CNC drilling and routing centre, manufactured in 2019. The machine was purchased new and has been used exclusively by our company. Our production volume is relatively low, and the machine has not been operated continuously or in two-shift production. It has typically been used for approximately 3–4 hours per working day. The machine is fully operational and currently in production. It can be inspected and tested under working conditions at our premises in Kaunas, Lithuania. A video of the machine in operation can be provided upon request. Ksdpfezzwl Dsx Ah Esdt Key information: Manufacturer: HOMAG Model: DRILLTEQ V-200 Year of manufacture: 2019 Condition: Used, well maintained and fully operational Purchased new and owned by one company Approximately 145,105 parts processed Main operating time: approximately 2,294 hours HOMAG powerTouch control system Used in a small-scale, single-shift production environment Price: EUR 38,000 net. VAT may apply depending on the buyer’s VAT status and country of destination. Location: Kaunas, Lithuania For further information, technical specifications and additional photos, please call +370 655 51230.

Condition: repair required (used), Year of construction: 1992, Weisser Heilbronn HEKTOR – Cycle-controlled CNC lathe - Bosch CC220 control system (requires repair) Kjdpfxoz Az Snj Ah Eodt - Includes tools and accessories - Includes operating manual and technical documentation - Year of manufacture: 1992 Technical data: - Distance between centers: 2000 mm - Center height: 300 mm - Swing over bed: 600 mm - Spindle bore Ø: 80 mm - Tailstock spindle taper: MK5 - Bed width: 430 mm - Operating voltage: 400 V - Dimensions (W x H x D): approx. 4700 x 2300 x 2100 mm - Weight: approx. 8000 kg

Condition: repair required (used), Year of construction: 2003, functionality: limited functionality, machine/vehicle number: 203-654, controller model: Siemens S7-200, number of chambers: 1, usable tank capacity: 4,000 l, No minimum price – guaranteed sale to the highest bidder! EXW – Dismantling and loading must be arranged by the buyer! The collection basin was renewed in 2022! TECHNICAL DETAILS Kdsdpfjzx S E Hjx Ah Ejt Number of chambers: 1 Chamber volume: 4,000 l Cleaning agent: Surfaclean 936 or Surfaclean 980 Concentration: 5% Ultrasonic power: 2 × 2,000 W Ultrasonic frequency: 25 kHz MACHINE DETAILS Control type: Siemens S7-200 Connected load: 75 kW Heating power: 57.5 kW Dimensions of the washing system: 1,900 × 2,800 × 1,700 / 3,300 mm with lifting device Dimensions of the collection basin: 3,600 × 3,300 × 400 mm Control voltage: 24 V DC EQUIPMENT Lifting device Lift truck with washing baskets Newly manufactured collection basin Ultrasonic cleaning Tools and fixtures Operating manual Wiring diagrams Maintenance history, partially available Note: The ultrasonic washing function was working during the last use. The lifting function for moving the container with the washing material did not function properly. The temperature control of the washing liquid did not function properly. The oil separation of the washing liquid did not function properly.

Condition: ready for operation (used), Year of construction: 2014, machine/vehicle number: 183610114, functionality: fully functional, stroke length: 1,200 mm, empty load weight: 1,500 kg, working width: 3,000 mm, working height: 1,710 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Press drive: Hydraulic Max. clamping width: 3,000 mm Max. clamping height: 1,710 mm Max. clamping depth: 100 mm Number of cylinders: 4 pcs Cylinder stroke: 1,200 mm Horizontal and vertical cylinders: Separately controlled MACHINE DETAILS Voltage: 400 V Current consumption: 3.5 A Fuse rating: 16 A Main motor power: 1.5 kW Connected power: 1.5 kW Dimensions & Weight Dimensions (L x W x H): 3,400 x 1,200 x 2,880 mm Unladen weight: 1,500 kg Number of transport packages: 1 pc EQUIPMENT Remote control Kdsdpfozzbb Nex Ah Est

Year of construction: 1991, operating hours: 19,888 h, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 1.844, MACHINE DETAILS Control system: CNC Kdjdpfxszxcl Ro Ah Ejt Operating hours: 19,888 h

Condition: ready for operation (used), Year of construction: 2011, operating hours: 51,000 h, functionality: fully functional, travel distance X-axis: 700 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 700 mm, controller model: FANUC 16i, spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Travel range X-axis: 700 mm Travel range Y-axis: 650 mm Travel range Z-axis: 700 mm Spindle speed: 12,000 rpm Tool interface: HSK A63 Number of tool magazine positions: 295 Rotary table: stepless, 360,000 indexing positions Rotary table speed: 65 rpm Pallet system: 7-position multi-pallet system Pallet size: 500 x 500 mm Maximum pallet load: 550 kg Maximum workpiece diameter: 800 mm MACHINE DETAILS CNC control: FANUC 16i Coolant tank: 750 l Coolant filtration system: self-cleaning Loading/unloading stations: 1 Operating hours: 51,000 h EQUIPMENT Cooling unit for temperature control of the spindle unit Spindle prepared for coolant supply through the tool flange Kdsdpfx Ahszxztas Eet Climate-controlled control cabinet with air conditioning unit Full enclosure of the work and machine area Work area lighting Scraper-type chip conveyor with rear discharge Conveyor screws for chip removal Closed upper machine cover, prepared for connection to a central extraction system C301 Workpiece cleaning C303 Tool taper cleaning C410 Tool Monitor MCM C305 Oil separator C333 Automatic coolant refill C308 High-pressure coolant system, 65 bar C403 Tool presence monitoring via laser C412 Balluff read/write system with JTERM-01 C408 Marposs wireless measuring probe MIDA T36 jFMX MCM monitoring system including Network Part Program

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 420 mm, travel distance Z-axis: 450 mm, controller model: Heidenhain iTNC 620, spindle speed (max.): 12,000 rpm, No minimum price – guaranteed sale to the highest bidder! Note: The machine is located on the first floor. The main difference between the MTRent MTcut v60 and the MTRent MTcut v60D lies in the inclusion of an additional rotary axis ("D" stands for rotary table or integrated 4th axis for extended machining capabilities). TECHNICAL DETAILS Travel in X-axis: 600 mm Travel in Y-axis: 420 mm Travel in Z-axis: 450 mm Distance from spindle nose to table: 120–570 mm Spindle speed range: 60 – 12,000 rpm Torque: 70 Nm (S6, 40 %) Spindle power: 11 kW (40 %) Spindle cooling: Oil/Air Tool interface: SK40 Pull stud: DIN 69871/72 Table dimensions: 750 × 420 mm Number of T-slots: 5 T-slot width: 14 mm H8 T-slot spacing: 65 mm Rapid traverse X/Y/Z: 32 Feed rate: 1 – 12,000 mm/min Positioning accuracy: ±0.005 mm Repeatability: ±0.003 mm Tool positions: 30 Tool change time: 1.5 s Maximum tool weight: 6 kg Maximum tool diameter: 76 mm Maximum tool length: 250 mm MACHINE DETAILS Control system: Heidenhain iTNC 620 Central lubrication: R68 (ISO 68) Hydraulic oil: R32 (ISO 32) Compressed air connection: 3/8" Compressed air: 6–8 bar Power supply: 400 V Fuse rating: 63 A Connected power: 25 kVA Coolant tank: 160 l Linear guides X/Y/Z: 30/35/35 mm Machine bed: Meehanite casting Machine weight: 4,000 kg EQUIPMENT Rotary table or integrated 4th axis Heidenhain iTNC 620 CNC control Digital Heidenhain drive technology Ceramic-bearing precision spindle Separate spindle cooling for constant temperature Integrated chip conveyor Maintenance-free Siemens spindle motor THK linear guides in all three axes 30-position tool changer with dual gripper Central lubrication Large access door to the work area Loading option from above using an overhead crane Two waterproof work area lights CE certification • The height and weight of the asset must be considered when selecting the transport vehicle. • A forklift is available for loading. • If the item is not collected on time, a storage fee of €20.00 per lot and for each day started will be charged. The fee must be paid before collection. Kdodozzlhaopfx Ah Est • The sale is made without any warranty or guarantee. • The information on the technical specifications comes from the original offer. • No liability is accepted for typing or measurement errors. If in doubt, please compare the information with the provided photos or inspect the item on site before the end of the auction.

Condition: ready for operation (used), Year of construction: 2024, functionality: fully functional, input voltage: 400 V, type of cooling: water, Equipment: cabin, For sale is a ready-to-use, compact, plug-and-play welding cell: OTC Easy Arc MIG/MAG 3.03. This system combines precise robotic technology with a high-performance, high-end welding power source and a fully automatically controlled horizontal rotary positioner. It is ideally suited for the automated, cost-effective production of small and medium-sized series. The entire cell is mounted on a stable base frame with a welding table/perforated plate and can be easily integrated into your production process. Technical highlights & components: Robot FD-B6: Highly dynamic 6-axis articulated arm robot, optimized for arc welding with internal cable routing (6 kg payload). Controller FD11: Modern robot controller for precise path guidance, including an ergonomic teach pendant for quick programming. Welding power source Welbee Inverter P400: Pulse welding power source (400 A) for spatter-free welding of steel, stainless steel, and aluminum, even at high welding speeds. Easy Arc PB250 Positioner / Horizontal Rotary Table: Fully controlled additional axis (up to 250 kg payload) for precise workpiece rotation, which enables welding in the optimal weld pool position, even with complex components. Safety concept: Complete enclosure including welding protection viewing windows and CE-compliant safety technology for direct use in a workshop. Condition & scope of supply: The system is in very good, fully functional, and ready-to-use condition, as it has been used only rarely. Scope of supply: Complete welding cell as described, including welding torch equipment, cable package, and documentation. The system is available immediately and can be inspected under power after consultation. Kedpfxszvqune Ah Esdt Technical data at a glance: Manufacturer: OTC DAIHEN Europe GmbH Model: Easy Arc MIG/MAG V03.03 Year of manufacture: 2024 Power connection: 400 V / 50 Hz B2B sale with exclusion of all warranties. Subject to prior sale. Net price plus VAT ex Philippsburg. Loading can be arranged on-site. Components: Robot welding cell as shown OTC welding robot Easy Arc MIG/MAG 1.03, robot FD B6 Easy Arc PB250 (Move) programmable positioner for automatic component alignment Controller FD11 Welding machine Welbee P400 Additional equipment: Water cooling If you have any questions or require further information, please send us a message or call us. An inspection and demonstration are possible at any time.

Condition: used, Year of construction: 2020, functionality: fully functional, machine/vehicle number: WT 1104, total height: 3,421 mm, total width: 4,704 mm, total length: 9,550 mm, load capacity: 200 kg, construction height: 3,421 mm, Vacuum Turning Portal for Panels The turning unit offers two different "automatic" operating modes: I. Component is conveyed without rotation The component is only shifted laterally, aligned to the reference edge (zero line) of the machining center, and then fed further to the CNC machining center (BAZ). II. Component is conveyed with rotation The component is shifted laterally and rotated along its longitudinal axis before being fed further to the CNC machining center. Each function can also be manually controlled in "manual" mode. SPECIFICATIONS: Max. panel dimensions: LWH: 8000mm x 2500mm x 100mm Max. weight: 200kg Min. panel dimensions: LWH: 1500mm x 1500mm x 12mm The turning portal is equipped with a total of 24 vacuum suction cups, ensuring gentle handling of the panels. The panels are always lifted via suction, then either moved horizontally to the zero line of the machining center or additionally rotated 180° en route before being delivered to the reference edge. The rotational movement is monitored via absolute encoders; the lateral positioning is controlled by adjustable photoelectric sensors. Vacuum is generated by a blower. The roller table, measuring 8500 mm x 4300 mm with roller diameter 108 mm, is fitted with material-friendly rubber rings and is driven by a SEW gear motor. Control of the roller table is via frequency inverter, adjustable speed up to 45 m/min. GENERAL INFORMATION: The entire area is enclosed by fencing; the longitudinal side of the system is secured by two sliding doors, which are safety-monitored. An operator touchpanel (12") is integrated into the fence area. The installed PLC (Siemens S7-1500) is programmed with three modes: • Automatic operation • Manual operation • Maintenance operation Input signals, loading side: – Start roller table – Rotate yes/no – EMERGENCY STOP complete system Kodpoyta R Ujfx Ah Esdt Input signals, unloading side: – Start roller table – EMERGENCY STOP complete system System output signals: – EMERGENCY STOP complete system – Panel infeed confirmed

Condition: like new (used), Year of construction: 2008, operating hours: 24,600 h, functionality: fully functional, clamping force: 1,600 kN, screw diameter: 50 mm, clearance between the columns: 520 mm, mold height (min.): 300 mm, overall weight: 6,600 kg, Equipment: documentation/manual, Here, we offer the following well-maintained used injection molding machine as part of our injection molding machine trade: We also purchase well-maintained injection molding machines, starting from the current model year 2010. We have been a wholesaler of used injection molding machines for over 25 years. Due to recent developments - tax information and advantage for the used machine: From July 1, 2025, used machines can also be considered for tax purposes with a special depreciation of 30% annually. In addition to the lower price compared to a new machine, you can claim the same depreciation amounts as with a new machine. Keyword: Growth booster, (§ 7 paragraph 2 EStG-E) Manufacturer: KraussMaffei Type: KM 160-750 Control: MC5 Year: 2008 Machine No.: 61011790 Operating Hours: 24,600 h Injection Unit Injection unit/screw: 50 mm Injection volume: 393 ccm Injection weight: 358 g Heating zones: 5 Nozzle stroke: 350 mm Injection pressure: 1892 bar Heating power: 16 kW Clamping Unit Tie bar spacing: 520 x 520 mm Platen size: 820 x 845 (h x v) Clamping force: 160 tons / 1600 kN Opening stroke: 650 mm Kedpfsz A Iarjx Ah Eodt Maximum platen distance: 950 mm Minimum tool mounting height: 300 mm Ejector stroke: 150 mm Weight: 6,600 kg Pump motor: 22 kW Dimensions: approx. 4.90 m × 1.60 m × 2.10 m Extras -Wedge shoe machine mounting -Hydraulic screw back-rotation lock -Hydraulic screw drive with standard speed -Pneumatic valve 1 on the operator side for blowing function (1 piece 5/2-way valve with 1 solenoid coil). -Control selectable: stroke/time or time/time. Quantity can be manually adjusted via 1 throttle valve at the valve outlet. -Nozzle protection door on the operator side, hinged -Ejector area protection door on the operator side, hinged -Mechanical interface according to EUROMAP 18 for handling device on the non-operator side (with intermediate plate up to and including KM 500) -End position "rear" of the ejector and the tool ejector plate monitored in sequence -Chrome-plated tie bars for the clamping unit and injection unit -Media monitor in the pump room for oil pan monitoring -Enlarged oil cooler for a maximum water supply temperature of 31°C. -Hydraulic core pull control 1-way on the non-operator side. -Water manifold 8-way -12 temperature control points for tool hot runner. Self-optimizing three-point PID controller with accuracy class 0.5. -Ejection of the cooled nozzle tip -Fan on the control cabinet -Power supply system: TN-C or TN-C-S or TN-S system (three-phase networks with a separately routed neutral conductor or a neutral conductor routed together with the earth conductor) -1 service socket 1-phase 10 A in the control cabinet, connected before the main switch in a country-specific version. -Signal interface according to EUROMAP 67 with fault signal and power supply socket CEE 16 A for handling device. -Event log for continuous recording and retrospective analysis -Quality monitoring package: Process monitoring (cycle actual values and integrals) by specifying tolerance bands, actual value display, actual value storage. Documentation can be printed. -Z-cycle time analysis, cycle storage -Language: German, Greek Visible peripherals are not included in the scope of supply. Free loading ex our warehouse in Hanover - worldwide delivery possible on request. Inspection under power possible by arrangement.

Condition: used, For inquiries regarding the vibratory plate, Mr. Herden will be happy to assist you (by phone). Weber CR 9 WSA Hatz Diesel Vibratory Plate Compactor / Electric Start / New unit / In stock & immediately available Sales price: €12,290.00 net / €14,625.10 gross 3-year manufacturer warranty Technical specifications Engine: Hatz Diesel Max. engine power: 10.5 (14.3) kW/hp Weight: 743 kg Centrifugal force: 100 kN Frequency: 65 Hz Working width: 75 cm Weber Smart Assist (WSA) - Analyzes signals from the machine’s integrated sensors and displays them graphically using symbols - Similar to the previous Weber MT engine protection, the engine automatically shuts down if continued operation would risk engine damage - Error symbols guide the operator step-by-step in troubleshooting - For an excessively dirty air filter, the cleaning and replacement process is shown step-by-step - Weber Smart Assist also includes the COMPATROL compaction control system, now in a new design - Displays compaction progress on an easy-to-read bar graph - New machine operation: after starting, vibration is activated at the push of a button - There is no throttle lever, as the engine speed is regulated automatically The reversible soil compactors of the CR series impress with strong compaction performance and maximum efficiency. They are first choice for classic road and civil engineering as well as paving applications. Well-balanced running characteristics, high stability, and low hand-arm vibration ensure outstanding operator comfort. CR 9 – Efficient machine with powerful compaction performance: - Infinitely variable forward and reverse travel. Hydraulic direction change - Throttle cable and hydraulic changeover are safely routed inside the guide bar - Low hand-arm vibration - Fatigue-free operation thanks to height-adjustable guide handle - Protection of machine and engine by engine protection frame and motor cover - Reduced maintenance due to self-tensioning centrifugal clutch - Easy servicing, with all maintenance components readily accessible - Safe and fast loading thanks to large, foldable lifting eye - Secure lashing during transport thanks to additional lashing points on the engine console - Greater operator convenience via electric start - Application areas: road and civil engineering, paving, and—thanks to the low overall height and working width—the CR 9 is also ideal for trench shoring Kedpfx Ajyi Rzpsh Eodt We have a large selection of various vibratory plates in stock for immediate delivery! Mr. Herden (phone) will be happy to assist you. We will gladly provide you with a financing offer upon request. We are an official Weber MT sales and service partner. We are an official Magni telehandler sales and service partner. We are an official Westtech sales and service partner. We are an official Gierking GMT sales and service partner. We are an official OilQuick sales and service partner. We are an official Holp sales and service partner. We are...

Condition: new, Year of construction: 2025, Table saw/router combination minimax twf 55 es M 3 UP Professional machine for skilled tradesmen, featuring motorized height and tilt adjustment of the router spindle, four speeds, and electronic control. Article number 5502266 Brand Holzkraft / SCM FEATURES Features Aluminum sliding table ✔ Handle on the sliding table ✔ Router fence FLEX ONE: heavy-duty professional version, automatic adjustment of the entire router fence depending on the tool diameter, manual adjustment of the chip removal, swing-away mechanism, aluminum fence jaws with connecting strips Spindle height adjustment motorized Telescopic miter fence with two folding stops Spindle tilt adjustment motorized Extension table ✔ Control Ready 3: Programmed movement of the routing unit in two axes, automatic adjustment of the entire router fence depending on the tool diameter, stepless adjustment via switch or automatic positioning system Arc routing guard ✔ Position of the controls Control panel at eye level, swiveling Eccentric clamp TECHNICAL DATA Dimensions and weights Length (product) approx. 1200mm Weight (net) approx. 510kg Width/Depth (product) approx. 2000mm Connection for dust extraction Dust extraction port diameter 2 x 120mm Work table Work table length 1200mm Sliding table length 1200mm Work table width 530mm Sliding table width 360mm Table height 900mm Sliding table height 142mm Installation information Space requirement length 2800mm Machine body width/depth 846mm Space requirement width/depth 2910mm Working area length 1600mm Explanation of space requirement The dimensions take into account maximum travel distances or usable lengths. Working area width/depth 2300mm Machine body length 1200mm Explanation of working area Please add the specified dimensions to the space requirement to obtain the recommended clear installation area for the machine. Electrical data Connection voltage 400V Power of drive motor 5.0kW Mains frequency 50Hz Router spindle Spindle tilt 0 to -45° Router spindle speed display Display on the control panel Usable spindle length 125mm Spindle arbor diameter 30mm Spindle speed(s) 3500/6000/8000/10000 min¯¹ Router tool diameter max. Tool diameter max. 240mm Tool diameter max. for profile routing 240mm Tool diameter max. for plunge routing 230mm Kodpfx Aohp Rc Ish Esdt

Condition: ready for operation (used), Year of construction: 2001, machine/vehicle number: HFE50-20LV010254, functionality: fully functional, pressing force: 50 t, stroke length: 350 mm, throat depth: 400 mm, working width: 2,090 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Number of axes: 8 Axis configuration: Y1 + Y2 + X1 + X2 + R1 + R2 + Z1 + Z2 Press force: 50 t Max. working width: 2,090 mm Frame distance: 1,665 mm Overhang: 400 mm Max. stroke: 350 mm Punch holder: Quick-change holder Tool holder type: European design MACHINE DETAILS Drive system: CNC Control system: Amada Operateur 2 CNC Power: 6 kW Dimensions & Weight Dimensions (L x W x H): 3,600 x 2,000 x 2,800 mm Weight: 5,500 kg Transport packages: 2 EQUIPMENT Tools Kdedpfx Ahszzbalo Eot Documentation CE marking

Condition: used, For inquiries regarding the vibratory plate compactor, Mr. Herden is available to assist you by phone. Weber CR 6 WSA Hatz Diesel Vibratory Plate / Electric Start / Brand New / In Stock & Immediately Available Sales Price: €8,990.00 net / €10,698.10 gross 3-Year Manufacturer Warranty Technical Data Engine: Hatz Diesel Max. engine output: 7.9 kW (10.7 HP) Weight: 428 kg Centrifugal force: 55 kN Frequency: 72 Hz Working width: 59 cm Kjdpfxoykhu Ne Ah Esdt Weber Smart Assist (WSA) - Evaluates signals from the sensors installed in the machine and displays them graphically using symbols - Similar to the previous engine protection from Weber MT, the engine shuts off whenever engine damage would be expected if operation continued - The user is also shown via symbols how to resolve any indicated faults - For a heavily soiled air filter, the cleaning and replacement procedure for the filter element is explained step by step - Weber Smart Assist also includes the COMPATROL compaction control, now presented with a new design - It provides the user with an easy-to-read and clearly understood bar graph display of the compaction progress - The machine operation is also new: once started, vibration is activated at the push of a button - There is no throttle lever, as the engine automatically adjusts to the correct speed The reversible soil compactors of the CR series stand out for their high compaction performance and top efficiency. They are the first choice for compaction work in classic road and civil engineering applications as well as paving. Balanced running properties, high smoothness, and low hand-arm vibrations ensure high operating comfort. CR 6 – Economical machine with strong compaction performance: - Infinitely variable forward and reverse travel. Hydraulic direction change - Throttle cable and hydraulic direction change are routed protected inside the guide bar - Low hand-arm vibrations - Fatigue-free operation with the height-adjustable guide handle - Protection for machine and engine through the engine guard frame and engine cover - Reduced maintenance effort thanks to the self-tensioning centrifugal clutch - Easy servicing, as all maintenance points are easily accessible - Safe and fast loading thanks to the large, foldable lifting eye - Secure lashing for transport with additional lashing eyes on the engine console - Enhanced operator convenience with electric start - Areas of application: road and civil engineering, paving, and thanks to its low height and working width, the CR 6 is also ideal for trench shoring We have a very large selection of different vibratory plates in stock and immediately available! Mr. Herden is happy to assist you by phone. On request, we can also provide you with a financing offer. We are an official Weber MT sales and service partner. We are an official Magni telescopic handler sales and service partner. We are an official Westtech sales and service partner. We are an official Gierking GMT sales and service partner. We are an official OilQuick sales and service partner. We are an official Holp sales and service partner. We are...

Year of construction: 2018, condition: used, This listing is for a Grant Controlled Rate Freezer - CRF-1 The unit is in full working condition and is ready for immediate release Product Overview: The CRF-1 Liquid Nitrogen-Free Controlled Rate Freezer is designed for precision-controlled freezing and cryopreservation of biological samples, such as embryos, stem cells, mammalian cells, spermatozoa, antibodies, tissue sections, and rodent organs. Unlike conventional liquid nitrogen-based freezers, the CRF-1 is liquid nitrogen and cryogen-free, eliminating contamination risks and making it suitable for use in cleanrooms and barrier facilities. It offers superior performance in terms of cell viability post-freezing and poses no fire hazard, unlike alcohol-based systems. Kjdpfjxv Dz Isx Ah Eedt The CRF-1 allows for highly accurate, reproducible, and controlled freezing rates, crucial for the cryopreservation of biological samples, ensuring optimal recovery upon thawing. Key Features: Cryogen-Free Design: The CRF-1 is free from liquid nitrogen and alcohol, offering a safer, cleaner alternative to traditional freezing methods. No contamination risk, making it ideal for use in sterile environments. Precise Cooling Control: The cooling rate is accurately controlled, especially for the critical nucleation/seeding phase, which ensures consistent and optimal recovery of cells. Wide Temperature Range: Capable of cooling down to -100°C with straws, offering a broad application range for biological cryopreservation. Simple Operation: The CRF-1 operates with or without a PC, and it can log data via PC software. Cooling profiles are displayed directly and can be customized. High Versatility: Compatible with cryovials, straws, bags, microplates, and Matrix-96-well block plates, allowing for research across multiple areas like stem cell research, transgenic embryos, mammalian cells, and more. Low Operational Costs: The CRF-1 runs at approximately 1% of the cost of liquid nitrogen-based freezing systems. Safety Features: Includes an optional Un-interruptible Power Supply (UPS) for complete cycle continuation in case of power failure. Compact & Quiet: Fits neatly on a bench-top and operates quietly, making it suitable for laboratory settings. Main Applications: Transgenic embryos research Stem cell research Clinical and research samples like lymphocytes and tissue cell lines Mammalian cell preservation (e.g., cardiomyocytes, adipose, liver, muscle) Cord blood-derived stem cells Adherent cells and stem cells in microplates Cell suspensions in numbered/barcoded arrays Robotic integration for high-throughput applications Veterinarian IVF applications Technical Specifications: Dimensions (w x d x h): 264 x 367 x 445 mm Weight: 9.8 kg Max Plate Temperature: 30°C Min Plate Temperature: -80°C (standard) or -100°C (dependent on model) Temperature Accuracy: ±0.5°C Temperature Stability: ±0.1°C Temperature Uniformity: ±1.0°C Max Cooling Rate: 10°C/min Max Temperature Stabilization Time: 5 minutes Key Benefits: Accurate and Reproducible Cooling Rates: Ensures controlled freezing rates and precise sample temperature management. Customizable Cooling Profiles: Choose from linear and non-linear profiles, or create your own tailored profile. No Cryogen or Liquid Nitrogen: Ideal for reducing contamination risk and the cost of liquid nitrogen. Low Running Costs: Estimated to cost only 1% of traditional liquid nitrogen-controlled freezing methods. End-of-Cycle Cooling Stability: Maintains a steady -100°...

Year of construction: 2011, condition: like new (used), Please notice that the entire factory with land and buildings is for sale! Kedpfx Aeim I Rueh Ejdt List of devices for the pellet production line No. 1 (with a drying line) No. Device name set. Description DRYER LINE: - bale feeder - length 9m - Rotogrin RSC B 36-132 shredder - chain scraper of wet raw material - length 12m - V500 wet raw material screw conveyor - 4 kW - drying cyclone with a rotary dispenser - 4 kW - dryer exhaust fan - 55 kW - a stove with an emergency chimney - 2.2 kW - SBP-2500 dryer drum - 5.5 kW - fuel dosing system with a container + burner - 5.9 kW - ignition detection system - extinguishing system - electrical installation, sensor system, wiring - control cabinet and automation Passat straw chopper 3 x 15 kW Beater mill ANDRITZ OPTI 900 - 250 kW, 3000 rpm JESMA EFF 64/2400 WB filter with fan 4 bar Buffer tank with feeders Conditioner ANDRITZ CM 1101 11 kW, 750 rpm Granulator PM 30 ANDRITZ 315 kW, 1500 rpm Automatic Roller Lubrication System Pellet cooler MOGENSEN G 1014 Screener A set of transport routes for the production line (pneumatic feeders, scraper and bucket conveyors MINIMAX spark detection system with control unit Control panel with software Power and control cabinets, wiring List of devices for the pellet production line No. 2 No. Device name set. Description Bale feeder - Length 9 m Rotogrin RSC B 36-132 chopper Beater mill ANDRITZ OPTI 900 - 250 kW, 3000 rpm JESMA EFF 64/2400 WB filter with fan - 4 bar ANDRITZ CM 1101 conditioner 11 kW, 750 rpm Granulator PM 30 ANDRITZ + lubrication system - 315 kW, 1500 rpm Pneumatic feeders from the hammer mill to the filter Power and control cabinets, wiring

Condition: used, For inquiries regarding the vibratory plate compactor, Mr. Herden will be happy to assist you (by phone at ...). Weber CR 8 WSA Hatz Diesel Vibratory Plate Compactor / Electric Start / New Unit / In Stock & Immediately Available Sales Price: €11,190.00 net / €13,316.10 gross 3-Year Manufacturer’s Warranty Technical Data: - Engine: Hatz Diesel - Max. Engine Output: 10.5 kW (14.3 hp) - Weight: 608 kg - Centrifugal Force: 75 kN - Frequency: 67.5 Hz - Working Width: 70 cm Weber Smart Assist (WSA): - Evaluates signals from the machine’s integrated sensors and displays them graphically via symbols - Similar to the previous Weber MT engine protection system, the engine will shut down whenever continuation could cause engine damage - Symbols also indicate to the operator how to resolve any displayed issues - In the event of a heavily soiled air filter, step-by-step instructions for cleaning and replacing the filter element are provided Kdsdoyi Rzvspfx Ah Eot - Weber Smart Assist also features the newly designed COMPATROL compaction control system - Provides the operator with a clear and easily readable bar graph display of compaction progress - New operating concept: After starting the engine, vibration is activated at the press of a button - There is no throttle lever as the engine automatically adjusts to the correct RPM The reversible soil compactors of the CR series stand out for their powerful compaction performance and maximum efficiency. They are the first choice for compaction work ranging from classic road and civil engineering to paving applications. Balanced running properties, high operating smoothness, and low hand-arm vibrations ensure a high level of operating comfort. CR 8 – Economical Machine with Powerful Compaction: - Infinitely variable forward and reverse travel; hydraulic reversing - Throttle cable and hydraulic reversing system routed and protected within the guide handle - Low hand-arm vibration - Fatigue-free operation with height-adjustable guide handle - Engine and machine protection via protective frame and cover - Lower maintenance requirements thanks to self-adjusting centrifugal clutch - Easy servicing with all maintenance components easily accessible - Safe and quick loading via large, foldable lifting eye - Secure tie-down for transport thanks to additional lashing points on the engine console - Greater operator comfort due to electric start - Areas of application: road and civil engineering, paving work, and, thanks to the low overall height and working width, the CR 8 is also ideal for trench shoring We have a large selection of various vibratory plate compactors in stock and available for immediate delivery! Mr. Herden will be happy to assist you by phone at ... Upon request, we will also be pleased to provide you with a financing offer. We are an official Weber MT sales and service partner. We are an official Magni telehandler sales and service partner. We are an official Westtech sales and service partner. We are an official Gierking GMT sales and service partner. We are an official OilQuick sales and service partner. We are an official Holp sales and service partner. We are...

Condition: like new (used), Year of construction: 2024, functionality: fully functional, power: 28 kW (38.07 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, travel distance X-axis: 3,200 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 300 mm, workpiece length (max.): 3,200 mm, workpiece width (max.): 1,300 mm, workpiece height (max.): 300 mm, number of axes: 3, number of slots in tool magazine: 14, controller manufacturer: OSAI, actuation type: pneumatic, total height: 2,900 mm, total length: 5,300 mm, total width: 3,150 mm, overall weight: 4,500 kg, table length: 3,200 mm, table width: 1,300 mm, Equipment: CE marking, documentation/manual, AES VEGA ULTRA 1332 – CNC Woodworking Machining Centre – Almost New – 2024 AES Vega Ultra 1332 CNC machining centre, manufactured in 2024, in almost new condition. The machine is equipped with a high-quality European and Japanese component package, making it a reliable and precise solution for professional woodworking and industrial CNC applications. Main specifications: Manufacturer: AES Model: Vega Ultra 1332 Year of manufacture: 2024 Condition: Almost new Working area: 3200 × 1300 mm ATC: 14-position automatic tool changer Tool holder: HSK 63F Main spindle: HSD, 12 kW Boring head: HSD Linear guides: THK Rack & pinion: Güdel Servo motors: Yaskawa Pneumatic components: Festo CNC controller: OSAI Open Smart High-quality component configuration Kjdjzxiu Sspfx Ah Esdt The machine was specified with premium components from established European and Japanese manufacturers: HSD – main spindle and boring head Güdel – rack and pinion system THK – linear guides Festo – pneumatic components Yaskawa – servo motors and drives OSAI – Open Smart CNC control The AES Vega Ultra 1332 is particularly suitable for demanding woodworking applications, including cutting, drilling, routing and machining of solid wood, MDF, plywood and other wood-based materials. The machine is in excellent, almost new condition and represents an opportunity to acquire a modern industrial CNC machine with a premium component configuration, without the lead time associated with ordering a new machine. Available for inspection and demonstration.

Condition: like new (used), Year of construction: 2022, Used HMZ-3 FR CNC miter saw with routing unit The miter line consists of: - a miter saw with a 5.5 KW braked motor and a 700 mm saw blade; - an infeed roller conveyor with a working length of 6,500 mm and a pusher unit; - an outfeed roller conveyor with a length of 6,000 mm; - an industrial computer with a 17” LCD color screen; - computer-controlled axes; - optimization software for importing Tekla/HSB CAD files, etc. Saw machine specifications: - motor power 5.5 KW; - saw blade diameter 700 mm, saw height 250 mm; - angle adjustment from 0 to 270 degrees; - noise level 81 dB; - combined guard/sound hood over the entire saw; - 2 dust extraction ports; - pneumatic material guiding system for the saw; - centerline adjustment 200 mm Infeed conveyor specifications: - robust steel construction. - working length 6,500 mm (- rollers with a diameter of approximately 50 mm and a load-bearing capacity of 125 kg each). - adjustable feet, 100 mm adjustment range. Outfeed conveyor specifications: - robust steel construction. - approximately 6,000 mm long. - equipped with an automatic scrap chute. Automatic positioning unit specifications: - reading accuracy selectable: 1 or 0.1 mm. - positioning accuracy plus or minus 0.2 mm. - speed up to 80 m/min. - Servo motor with rack and pinion, driven by a frequency inverter. - steel guide with 8 adjustable bearings. Computer specifications: - Industrial computer with a 19” LCD touchscreen. Kodpfx Ahezg Il Ss Eedt - hard drive 200 Gb, and USB port. - network card and Windows 10. - special, H&M-developed, Dutch-language Windows software. - graphical display of the cutting pattern. - control from the office via a network or by importing a drawing program, e.g., HSB CAD. - integrated optimization module. Operation: A cutting list is created or called up on the control computer and activated. Then, the available lengths and quantities can be specified, so that the machine can optimize the cutting process. After that, the saw can be started, and the machine requests the desired length. The pusher is in the starting position, and the control system requests the correct length. After a start command is given, the pusher starts and the beam is pushed through the machine and automatically cut to the desired specifications. The cut product ends up on the outfeed table. Additional options on the machine: - Label printer with software and stand. - Supports for the saw (8 pieces). Routing unit The saw is combined with a routing unit with a 90-degree (vertical) stroke. Max. reach: - 150mm. Height - 120mm. Depth Dust extraction port for routing unit: 100mm.

Condition: refurbished (used), Year of construction: 2012, machine/vehicle number: AA1/016854, functionality: fully functional, 3-AXIS DRILLING & MILLING CENTER Make: SCM Model: TECH Z2 Comp R0410.01 Serial No.: AA1/016854 Year: 2012 (Photos taken before overhaul, functional testing, and cleaning) MAKING CAPACITIES: - Max. workpiece height (thickness): 160 mm - Max. workpiece length: 2700 mm Dual station: 1210 mm - Max. workpiece width: 1300 mm Movements: - X-axis travel: 3060, Y-axis: 1735, Z-axis: 250 mm - Max. travel speed (vector: 60 m/min) MACHINE COMPOSITION: - 6 Pneumatically clamped beams for suction cups, e.g., 120x120 or 55x120 mm - Unit Automatic lubrication - Mounted unit on the neck of the sign composed as follows: (X movements by rack and pinion, Y movements by screws and bushings; high-quality precision linear guides with automatic lubrication) • 11 kW (15 HP) milling/routing unit: - Rotation 1500 - 24000 rpm, variable speed, right/left direction - Tool holder connection type HSK63F, ER32 collet - Onboard magazine for 8 tools - Perimeter extraction hood • 18-chuck drilling unit: - 12 independent vertical chucks (8 in the X direction, 5 in the Y direction) - 6 horizontal chucks (4 in the X direction, 2 in the Y direction) - Center distance between chucks 32 mm for M10 / Ø11 mm drill bits - Rotation speed 4000 rpm - Pneumatic vertical stroke 60mm - Perimeter extraction hood • Integrated unit for groove sawing and milling - Ø120mm blade, 6mm thick - 6000 rpm speed - 60mm pneumatic vertical stroke • Mobile console on a jib with a control PC: – Windows XP operating system – 17" LCD screen – Ethernet connection – Xilog and Maestro machine interface software OTHER FEATURES: - 400V overall power supply. Three-phase + N+T 50Hz IN37A - 12 kW electro-spindle motor Kedpfxov Tzrve Ah Eedt - 2.2 kW drilling/grooving motor - 1 x 2.4 kW vacuum pump: 90-108 m3/h - Pneumatic supply >=7 Bar - Suction: Suction inlets: 2 x Ø 150 mm (1 x Ø 200 mm inlet using the installed bypass) Recommended speed: 30 m/s - 3400 m3/h - CE-compliant machine with safety zone and light barrier Operating dimensions with safety zone: see documentation excerpts Shipping dimensions: to be specified when preparing the equipment Estimated total weight: 2200 kg Machine supplied with instruction manual and software, spare parts list, electrical and pneumatic diagrams. Please contact us for the supply of consumables, accessories, and/or vacuum systems. Machine serviced and brought into compliance, with quality control and dynamic functional testing. 3-month warranty and compliance certificate. Available from stock, subject to prior sale. Prices excluding VAT. Delivery and additional services upon request.