Used Round Magazine Nailer for sale (6,010)

Condition: like new (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: 1234, input voltage: 380 V, input frequency: 50 Hz, Codix nailer fully rebuilt in Sophograf France 2 years ago. The machine is now setup to make doubleside stringpallets Chedpev Hh Haofx Afgsc

Condition: not inspected (used), Year of construction: 2016, functionality: unexamined, edge thickness (max.): 22 mm, rotational speed (max.): 12,000 rpm, Equipment: CE marking, The machine has the following configuration: Pre-milling unit Automatic, timer-controlled intervention and positioning via NC Edge preheating lamps Edge band magazine Glue pot for EVA hot-melt adhesive Chjdpfx Afsyxndbjgec Premelter for EVA hot-melt adhesive QM-705 End trimming unit IN-801 Number of motors: 2 Top and bottom flush trimming unit RS-100 Number of motors: 2 Motor power: 2 kW Speed: 12,000 rpm Fine finishing and contour trimming unit RF-100 Number of motors: 2 Motor power: 2 kW Speed: 12,000 rpm Corner rounding unit AR30 Number of motors: 2 Motor power: 0.8 kW Speed: 12,000 rpm Automatic, timer-controlled intervention End cutting unit RB02 Positioning by NC Glue scraping unit RCC-701 Polishing unit SP-501 Number of motors: 2 Motor power: 0.25 kW Spraying unit LPT-700 TECHNICAL DETAILS Panel height min: 10 mm Panel height max.: 60 mm Edge thickness min.: 0.4 mm Edge thickness max.: 22 mm MACHINE DETAILS Total connected load: 22 kW EQUIPMENT Feed pressure with rubber belt Panel support guides with NC positioning CE marking The machine is sold and delivered as is (“as seen and approved”) based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the place of destination. External reference: 7673

Condition: used, Year of construction: 2008, power: 41 kW (55.74 HP), edge thickness (max.): 3 mm, controller model: ICOS OPEN, The machine has the following configuration: Pre-milling unit Manufacturer model: R3 L20 Engagement control: Automatic, time-controlled Motor power: 4 kW Speed: 9,000 rpm Edge processing Number of edge processing units: 10 Crosscut saw unit Manufacturer model: 8.42/39/B Number of motors: 2 Motor power: 0.6 kW Speed: 12,000 rpm Flush trimming and rounding unit Manufacturer model: 08.055 Number of motors: 0.6 (?) Motor power: 1 kW Speed: 12,000 rpm Corner rounding unit Manufacturer model: 08.342 Number of motors: 2 Motor power: 0.66 kW Speed: 12,000 rpm Scraper blade unit Manufacturer model: 08.50 Belt sanding unit 1 Manufacturer model: 08.62 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 2 Manufacturer model: 08.062 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 3 Manufacturer model: 08 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 4 Manufacturer model: 08.617-2 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 5 Manufacturer model: 08 Processing unit 10 Manufacturer model: 08.190 Motor power: 4.5 kW Speed: 9,000 rpm TECHNICAL DETAILS Workpiece dimensions Max. panel height: 60 mm Min. panel length: 130 mm Min. panel width: 65 mm Edge material Min. edge thickness: 0.4 mm Max. edge thickness: 3 mm Feed Max. feed rate: 30 m/min Pressure: Rubber belt Number of panel sizing/milling units: 1 Chjdpfx Afjzmtkajgoc MACHINE DETAILS Control system: ICOS OPEN Total connected power: 41 kW EQUIPMENT Number of panel sizing/milling units: 1 Lamps for preheating the panel side Edge roller magazine with 2 positions PUR pre-melting unit Pressure roller set with 5 pressure rollers Spraying unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at its destination. External reference: 5657

Condition: used, Year of construction: 2017, power: 20 kW (27.19 HP), edge thickness (max.): 12 mm, feed rate X-axis: 20 m/min, The machine has the following configuration: Pre-milling unit End-capping unit Number of motors in end-capping unit: 2 Rough milling unit, top and bottom Number of motors in rough milling unit: 2 Edge rounding unit Number of motors in edge rounding unit: 2 Edge trimming unit Glue application unit Edge finishing unit Number of motors in edge finishing unit: 2 TECHNICAL DETAILS Workpiece processing Min. board thickness: 8 mm Max. board thickness: 60 mm Min. edge thickness: 0.4 mm Max. edge thickness: 12 mm Max. feed rate: 20 m/min MACHINE DETAILS Chsdozmtldepfx Afgoc Total connected load: 20 kW EQUIPMENT Preheating lamps for workpiece sides Edge roller magazine Glue reservoir for EVA hot melt adhesive Spray unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents, which are for descriptive purposes only. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7981

Condition: used, Roundo PS340 3000 mm Hydraulic Double-Pinch Plate Bending Rolls Manufacturer: Roundo AB Model: PS340 Year: 1983 Country of manufacture: Sweden Type: Hydraulic three-roll double-pinch plate bending rolls Capacity Maximum working length: 3,000 mm Pre-bending capacity: approximately 12 mm mild steel aximum rolling capacity: approximately 18–23 mm mild steel, depending upon finished diameter Standard upper-roll diameter: 340 mm Plate capacities based upon mild steel of approximately 270 N/mm² yield strength Minimum rolling diameter: approximately 1.1–1.4 times the upper-roll diameter, depending upon material thickness Remaining straight edge after pre-bending: approximately 1.5–2 times plate thickness Features Hydraulic double-pinch design Both lower rolls independently hydraulically adjustable Pre-bending of both ends without removing and reversing the plate Codszuzpyopfx Afgohc Hydraulic rotation of all three rolls Infinitely variable rolling speed Hydraulic powered drop end Portable pendant control Front safety trip bar Heavy-duty fabricated and stress-relieved frame Forged and crowned steel rolls Rolls mounted in heavy-duty roller bearings Suitable for cylindrical and conical bending Approximate machine weight: 14,000–15,000 kg, subject to confirmation Approximate main motor: 22 kW, subject to data-plate confirmation

Year of construction: 2018, condition: like new (used), functionality: fully functional, TECHNICAL DETAILS Load cell: 2 pcs Xforce K Testing software: testControl II & testXpert III Load cell: Xforce K Measuring amplifier: DCSC module Documentation: available FURTHER TECHNICAL DETAILS - as per documentation, no guarantee Cjdpfx Ajzpw Hdjfgshc Maximum test force Fmax: 50 kN Total height of the testing chamber: 1,534 mm Height of the lower testing chamber without attachments: 1,355 mm Height of the upper testing chamber without attachments: 1,369 mm An additional crossbeam is required for the upper testing chamber. Testing chamber width: 440 mm Load frame Load frame height without uprights: 1,714 mm Load frame height with uprights: 1,829–2,694 mm Load frame width without uprights: 760 mm Load frame width with uprights: 936 mm Load frame width with uprights and machine electronics: 1,124 mm Load frame depth: 140 mm Load frame depth without uprights and with drive base: 507 mm Load frame depth with uprights: 762 mm Load frame depth with uprights and machine electronics: 765 mm Weight and footprint Weight with machine electronics, uprights and typical attachments: approx. 300 kg Net footprint: 0.01 m² Load frame footprint: 0.713 m² Average sound pressure level at maximum speed at a distance of 1 m from the front of the machine: 61 dB(A) Drive Crossbeam speed: min. 0.0005 mm/min to max. 600 mm/min Crossbeam return speed: max. 1,000 mm/min Deviation from the set drive speed: max. 0.05% of the actual value Drive path resolution: 0.317891 nm Positioning repeatability without direction reversal: ±2.0 µm Adaptive control Cycle time: 1,000 Hz Power input Power connection plug CEE 7 (Schuko) Power connection: 230 V, 1 Ph/N/PE Power consumption at full load: approx. 2.3 kVA Mains frequency: 50/60 Hz Mains-side protection of the power connection cable: 16 A Safety functions The drive is equipped with a mechanical holding brake. When switching off, when the emergency stop is activated, or in the event of a power failure, the material testing machine stops at the current position. Unintended unloading due to energy stored in the specimen is prevented.

Condition: excellent (used), Year of construction: 2007, Technical data: Codpfx Afsztckiegjhc Working length: 2550 mm Max. bending capacity for small diameters: 12.0 mm Bending capacity from diameter 900 mm: 18 mm Bending allowance: 10 / 12.0 mm Roller diameter: 310 mm Hydraulic folding bearing Drive power: 11 kW Lateral bending support Sheet metal holding device Digital display Dimensions (length x width x height): approx. 4200 x 1500 x 1650 mm Weight: approx. 10 tons Condition: Overall in very good condition, used only sparingly. The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: excellent (used), Zwick / Roell Z020 Allround-Line BT2-FR020TNW.A50 Material Testing Machine, 20 kN Manufacturer: Zwick / Roell Series: Z020 Allround-Line Type: BT2-FR020TNW.A50 Machine Type: Servo-electric Material Testing Machine / Universal Testing Machine Max. Testing Force: 20 kN For sale is a used Zwick / Roell Z020 Allround-Line material testing machine with testControl II control system, industrial PC, and installed testXpert V3.5 software. The machine is suitable for tensile and compression tests on metals, plastics, elastomers, composite materials, and numerous other materials, and is used in testing laboratories, quality assurance, research and development, and training. Technical Data: Manufacturer: Zwick / Roell Series: Z020 Allround-Line Type: BT2-FR020TNW.A50 Max. Testing Force: 20 kN Testing Direction: Tensile and Compression Testing Space Height: 1,000 mm Crosshead Speed: 0.0005–1,000 mm/min Power Supply: 230 V / 50–60 Hz Power Consumption: 8 A Control System: testControl II Software: testXpert V3.5 Load Cell: Zwick / Roell Xforce P 20 kN Zwick / Roell Xforce P 2.5 kN Dimensions: Machine Dimensions (W × D × H): approx. 1,244 × 690 × 1,324 mm Machine Weight: approx. 212 kg Equipment: Cjdpfx Ajzra Rqsfgshc testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Testing table Testing fixture Connection and cabling Accessories as shown in the pictures Shipping Data: Dimensions (W × D × H): approx. 1,244 × 690 × 1,324 mm Shipping Weight: approx. 212 kg Condition: Used Optical condition as shown in the pictures. Functional scope as shown in the pictures. Nameplates present. Scope of Supply: Zwick / Roell Z020 Allround-Line BT2-FR020TNW.A50 testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Testing table Testing fixture Connection and cabling Further accessories as shown in the pictures The table, monitor, keyboard, and mouse shown in the photos, as well as any other items not explicitly mentioned, are not included in the sale. Availability: by arrangement. Scope of supply as shown in the pictures. Subject to changes, errors, and prior sale.

Condition: used, Year of construction: 2010, Technical details: • Edge material thickness for strip material: 0.4–6 mm • Edge material thickness for coil material (depending on material): 0.4–3 mm • Edge material height: max. 65 mm • Workpiece thickness: 6–60 mm • Minimum workpiece width: 65 mm • Minimum workpiece length: 160 mm • Feed speed: 10 m/min • Integrated control panel on the front side, in the infeed area • Control system: PPC 221 – Power PC • Pull-out workpiece support table, extension: 600 mm • 1801 Pre-milling unit with diamond milling cutter (1 × 0.8 kW, 1 × 1.2 kW, 200 Hz, 12,000 rpm) • 1903 Edge band magazine, pre-cutting up to 3 mm • 1906 MG combined glue application unit (cartridge and granulate) Chsdjzxww Ujpfx Afgec • Pressure regulator for cartridge glue application with pneumatic control • 1912-3 Pressure roller unit • 1918 Pneumatic end-trimming unit • 1827 Multifunctional milling unit (pneumatic control) • 1832 Corner rounding/milling unit • 1929 Scraper unit, R = 2 mm • 1964 Flat scraper Specifications are provided for information only. This machine is offered for sale on behalf of a customer. Viewing is available by prior arrangement. Please contact us through the platform's messaging system for further information and the relevant technical contact details.

Condition: new, Year of construction: 2026, Feed speed 9 m/min Board thickness 12 - 45 mm Minimum board dimensions (L x W) 90 x 170 mm Worktable height 960 mm Table extension (steady rest) 560 mm Extension connector ⌀ 125 mm Installed power 6.1 kW Pre-milling 3000 rpm Front/back 12,000 rpm Top/bottom 12,000 rpm Polishing 3000 rpm Machine dimensions 3960 x 720 x 1748 mm Weight (net/gross) 800 / 950 kg Feed motor power 0.75 kW Glue tank heater motor power 1.315 kW Pre-milling motor power Milling 1.5 kW Plate heating motor power 0.125 kW Glue spindle motor power 0.25 kW Front/rear cutting motor power 0.37 kW Top/bottom cutting motor power 0.37 kW x2 Corner trimming motor power 0.37 kW Polisher motor power (top/bottom) 0.12 kW x2 (3-phase), 0.18 kW x2 (1-phase) Touchscreen control panel Chsdpfx Aszp Nz Hefgjc Air consumption 350 L/min Minimum extraction power 5 kW (for effective dust extraction from the edge bander)

Condition: used, Esterer round timber intake, 4-strand with feed table with separator with inserter complete with chains and motors Total conveyor length: approx. 6.8 m Total width: approx. 7.5 m Chsdpfx Aoyxz U Tofgoc Already dismantled Location: Austria, near Graz (Internal number: 10br12)

Condition: excellent (used), Year of construction: 2006, Arburg 370 S 600-290 (2006) Screw ø 35 mm 📐 CLAMPING UNIT Clamping force: 600 kN Closing force: 38 kN Opening force / increased: 24 / 160 kN Opening stroke: 400 mm Mould height min.: 200 mm Daylight max.: 600 mm Distance between tie bars: 370 × 370 mm Platen size: 510 × 510 mm Weight of mov. mould half: 360 kg Ejector force: 125 kN Ejector stroke: 125 mm ⚙️ HYDRAULICS Drive power: 15 kW Total connected load: 23,9 kW 💉 INJECTION UNIT — ø 35 mm Screw stroke max.: 150 mm Effective screw length L/D: 20 Injection volume max.: 132 cm³ Shot weight max.: 20,5 g PS Material throughput max.: 10,5 kg/h PS Injection pressure max.: 2000 bar Injection flow max.: 140 cm³/s Injection flow with accumulator: 430 cm³/s Back pressure max.: 350 / 200 bar Screw speed max.: 54 m/min Screw torque max.: 380 Nm Nozzle contact force: 60 kN Nozzle retraction stroke: 240 mm Cedpfx Afjzrv Irogjhc Heating zones / power: 4 zóny / 5,8 kW Nozzle heating: 0,6 kW Hopper capacity: 50 l 📦 DIMENSIONS & WEIGHT Oil capacity: 135 l Net weight: 3300 kg Electrical connection: 80 A

Condition: new, Model Name Csdpfjgvkctox Afgshc Shark 282 SXI evo

Condition: excellent (used), Manufacturer: ARBURG Model: Allrounder 270-S-500-60 Chedox Eiq Hjpfx Afgjc Year of manufacture: 1998 Serial number: 173062 Control system: Arburg Selogica Screw diameter: 18 mm

Condition: used, Year of construction: 2000, Edge banding machine, single-sided Manufacturer: OTT Type: Pacific V 6-F Year of manufacture: 2000 Technical data: Edge thickness: 0.2 - 6 mm Workpiece thickness: 8 - 42 mm Workpiece width: min. 70 mm Workpiece length: min. 0 mm Feed speed: 12 m/min Electrical connection: 3 x 400 V, 50 Hz Cjdpfxjzuyh Uj Afgjhc Extraction: 2 x 120 mm at 20 m/s Extraction capacity: m³/h Equipment, processing units: Edge trimming 2 x 1.5 kW, 12,000 rpm, 200 Hz two tool-controlled spindles Gluing unit Rapid heating tank with Melt-matic automatic edge magazine with optical monitoring for strip edges in fixed lengths Release agent spraying device Cutting unit 2 x 0.2 kW, 12,000 rpm, 200 Hz automatic pivoting 0 / 3 Flush trimming unit x 0.43 kW, 12,000 rpm, 200 Hz Radius trimming unit R2 - R5 2 x 0.3 kW, 12,000 rpm, 200 Hz 2 quick-change stations for trimming units Corner rounding trimming unit 2 x 0.3 kW, 12,000 rpm, 200 Hz Scraper blade 2 x carbide scrapers Smoothing unit 2 x 0.2 kW, 2,800 rpm, 50 Hz Weight: 2,000 kg Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is not binding.

Condition: excellent (used), functionality: fully functional, Holz Her Auriga 1308 XL FÜ + PU compact design - edge thickness 0.4 - 8 mm SPS-based Edge-Control PPC 231 touchscreen control system motor-driven, position-controlled bridge height adjustment pre-milling unit for attachment before the gluing section fully automatic edge magazine for roll and strip material GLU JET cartridge gluing station + PU gluing glue application via nozzle technology workpiece height 6-60 mm automatic glue height adjustment pressure unit 1912-3, pneumatic trimming unit 1918, pneumatic, for roll and strip material up to 8 mm edge thickness with pneumatic adjustment for 0-10° bevel of the trimming saw milling unit 1827 MOT 4, flush trimming 8 mm, radius milling - bevel milling - 15° MOT NC axes controlled via control panel profile milling unit 1832 pneumatic, rounding of corners up to edge thickness 3 mm in a single pass Chedpfxjzib Nie Afgec scraper blade unit 1929 MOT2 for bevels and radii with 2 scraper blade holders, NC axes controlled via control panel surface scraper blade unit - finishing buffing unit - polishing spraying system at the infeed and outfeed complete tool equipment included first delivery 2013 machine is FUNCTIONALLY TESTED and in TOP CONDITION available from warehouse Lieboch

Condition: used, Holz Her Sprint 1321, with edge banding and PU adhesive application Heavy-duty version – edge thickness 0.4 – 15 mm SPS-based Edgecontrol control panel Motorized, position-controlled bridge height adjustment Pre-milling unit for attachment before the gluing station Fully automatic edge magazine for roll and strip material Gluing unit with cartridge system + PU adhesive application Chodpfxozp Hc Uo Afgoc Automatic glue height adjustment / touch probe nozzle Pressure unit 1913, pneumatic Trimming unit for roll and strip material 1918 – 15 mm With pneumatic adjustment for trimming saw angle from 0-10° Multi-function milling unit with motorized adjustment: flush trimming – 15 mm, radius and chamfer milling – 15° Profile milling unit – corner rounding 1833 Scraping unit for chamfers and radii 1929, pneumatic Pneumatic infeed and outfeed Surface scraping unit – finishing, pneumatic Buffing unit for finishing and edge polishing with 2 textile discs HIGH-END spraying system Complete set of tooling Machine is in FULLY OPERATIONAL CONDITION Machine from a craft business / consignment sale Available from stock in Lieboch, NET € 21,500.00

Condition: used, Year of construction: 2002, functionality: fully functional, LIGMATECH ZHR 15 Transfer Unit / Roller Conveyor (Workpiece Return Conveyor / Boomerang) – will be sold separately from the edgebanding machine. HOMAG Optimat KL79 A20/S2 (2002) Installed Units: • A20/S2 gluing station (edge thickness up to 20 mm) • Edge feed magazine • Front/rear end trimming units (two saw modules) • Top and bottom trimming units • Corner rounding units (two heads) • Profile scraper units (top/bottom) • Glue joint scraper Chodpfx Afjycg D Tegsc • Buffing/polishing units • Pneumatic control and vacuum extraction system Technical Data (from manufacturer specifications): • Feed speed: 18–24 m/min • Edge thickness: 0.3–20 mm • Workpiece thickness: 12–60 mm • Minimum workpiece width: 55 mm (22 mm thickness) / 100 mm (60 mm thickness) • Machine length: 10,115 mm • Weight: ~6,200 kg • Power supply: 400 V, 50/60 Hz • Compressed air: 8 bar

Condition: used, Year of construction: 1994, Dough divider and rounder WP Multimatic MUC 5 Year of manufacture: 1994 Condition: Dough dividing chamber refurbished, ready for immediate use Type: MUC 5, 5-row model Weight setting via handwheel Weight range: 30 to 90 g Includes 1 chamber drum, selection based on availability Capacity: 600 to 2000 pieces/hour per row (depending on dough type and weight) Chjdpfxsz A Shmo Afgoc Individual pistons can be locked for, for example, 4-row operation.

Condition: used, Dough divider and rounder König Industrie Rex I 6 Condition: cleaned and inspected Includes dough hopper with lubrication, laterally adjustable with ladder Weight range: 30–100 g Csdsz A Sfrepfx Afgjhc Max. hourly output: 18,000 pieces Siemens touch control with program memory Includes 1 chamber drum Includes 1 set for 4-row production, 1 set for 6-row production

Condition: ready for operation (used), Year of construction: 2006, operating hours: 3,010 h, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 530 mm, travel distance Z-axis: 510 mm, controller model: Fanuc Oi-MC, spindle speed (max.): 10,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 1,000 mm Travel range, Y-axis: 530 mm Travel range, Z-axis: 510 mm Table length: 1,200 mm Table width: 510 mm Orientation: Horizontal Tool interface: ISO 40 Max. spindle speed: 10,000 rpm Tool positions: 24 MACHINE DETAILS Control: CNC Control system: Fanuc Oi-MC Number of axes: 3 Power: 11 kW Dimensions & Weight Cjdjz Ebb Uspfx Afgehc Dimensions (L x W x H): 2,850 x 2,150 x 2,300 mm Net weight: 6,000 kg Shipping packages: 3 Operating hours: 3,010 h EQUIPMENT Spindle cooling Documentation CE marking External cooling Tool magazine Chip conveyor Tools included

Condition: like new (used), Year of construction: 2008, travel distance X-axis: 700 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 700 mm, feed rate X-axis: 60 m/min, feed rate Y-axis: 60 m/min, feed rate Z-axis: 60 m/min, nominal power (apparent): 68 kVA, controller manufacturer: HEIDENHAIN iTNC 530, workpiece height (max.): 1,000 mm, workpiece diameter (max.): 800 mm, workpiece weight (max.): 600 kg, total height: 2,547 mm, total length: 5,866 mm, total width: 4,196 mm, table width: 500 mm, table length: 500 mm, overall weight: 12,000 kg, spindle speed (max.): 18,000 rpm, spindle motor power: 34,000 W, number of slots in tool magazine: 120, Equipment: chip conveyor, documentation/manual, CNC controller: HEIDENHAIN iTNC 530 Axes: X-axis travel mm: 700 Y-axis travel mm: 700 Z-axis travel mm: 700 Distance spindle nose - table surface mm: 100 - 800 Rapid traverse m/min: 60 Acceleration in the axes m/s2: 6 / 6 / 5 Worktable: Number of pallets: 2 + 5 Table dimensions mm: 500 x 500 Maximum workpiece size (D x H) mm: 800 x 1.000 Max. workpiece weight kg: 600 T-Slot version: DIN 55201-A2 APC time s: 9,5 División estandar Grados: 360º (1º) Spindle: Spindle speed rpm: 18.000 Spindle drive power kW: 34 / 28 Spindle torque Nm: 110 Tool system: Tool holder: HSK-A63 Tool magazine slots: 120 Max. Tool Diameter: 80 Max. Tool Length mm: 550 Cedpfxowhdhzj Afgshc Max tool weight kg: 12 Chip-to-chip time s: 2,9 Equipment: Electronic Handwheel Chip conveyor Rotating inspection windows Rinsing gun Signal lamp Tool breakage probe 3D quickSET Workarea light CE conformity Cooling device blowing air through spindle center, selectable via M-function MPC – Machine Protection Control Paper band filter Infrared Probe Heidenhain TS640 Blum laser tool measurement Taper clear brushes Blum laser NT Hybrid Round pallet Storage (RPS 5) Measuring probe Heidenhain TS 640 Production package Internal cooling supply 40 BAR Cooling: Cooling through the Spindle Center bar: 40 BAR Tank capacity: 980 High-pressure bar: 40 BAR Machine running times: Under power: 95.210 Operating Time: 44.971 Rated power kVA: 68 Basic machine dimensions / weight: Length mm: 5.866 Width mm: 4.196 Height mm: 2.547 Weight kg: 12.000.

Condition: excellent (used), Year of construction: 2004, operating hours: 88,926 h, functionality: fully functional, machine/vehicle number: 194501, clamping force: 600 kN, screw diameter: 25 mm, clearance between the columns: 370 mm, overall weight: 2,930 kg, Equipment: documentation/manual, We are selling a very well-maintained 370C. The machine is connected to the power supply and can be inspected at any time. Cedpez Dq I Ujfx Afgohc 1x core pulling unit, hydraulic, Drop-off switch, Handling interface EM67

Condition: new, Year of construction: 2026, functionality: fully functional, Labeling system for round and square canisters Stainless steel frame Chsdpeu Ia E Iefx Afgjc 170 mm wide link chain (optionally wider possible) Standard label width 140 mm or 190 mm, optionally up to 260 mm possible Label length 300 mm, optionally longer Dispensing speed up to 30 m/min., optionally 50 m/min Product diameter according to technical testing from 20 mm - 170 mm, optionally other sizes possible Touch screen display, with storage option Label dispenser with three-dimensional adjustment option Product separation with two-sided belts Product alignment for square bottles Top belt guide for square and oval products Other labeling options, such as lid labeling, seal labeling, bottom labeling, etc.

Year of construction: 2016, condition: excellent (used), functionality: fully functional, machine/vehicle number: Elite P27965, This Kliklok Certiwrap Elite was bought to wrap snack pots at high speed. It is in nearly new condition as it has not been used a great deal. Chsdpoz E N Hrjfx Afgec