Used Homag Kl 79 for sale (469)

Condition: used, Year of construction: 2002, functionality: fully functional, HOMAG Optimat KL79 A20/S2 (2002) – Full Configuration The edge banding line is in satisfactory working condition, fully operational and ready for production. Installed Units: • A20/S2 gluing station (edge thickness up to 20 mm) • Edge feed magazine • Front/rear end trimming units (two saw modules) • Top and bottom trimming units • Corner rounding units (two heads) • Profile scraper units (top/bottom) • Glue joint scraper • Buffing/polishing units • Pneumatic control and vacuum extraction system Technical Data (from manufacturer specifications): • Feed speed: 18–24 m/min • Edge thickness: 0.3–20 mm • Workpiece thickness: 12–60 mm • Minimum workpiece width: 55 mm (22 mm thickness) / 100 mm (60 mm thickness) Codpfxoycg D To Aa Eegp • Machine length: 10,115 mm • Weight: ~6,200 kg • Power supply: 400 V, 50/60 Hz • Compressed air: 8 bar

Condition: ready for operation (used), Year of construction: 2001, This HOMAG Optimat KL 78/A20/S2/Z was manufactured in 2001. A robust single-sided edge bander, it features a comprehensive setup including joint milling, a glue premelter, pressure zone, snipping, and flush trimming units. It also boasts advanced contour and groove trimming, profile and surface scrapers, and a buffing unit, all controlled by the Homatic NC 21 unit. Contact us for more information about this machine. Cjdpfxoyap Tle Aa Ejgp Machine Benefits Technical Machine Benefits • Single-sided edge banding machine with workpiece return • Joint milling • Gluing section with glue premelter • Pressure zone • Snipping unit • Flush trimming • Contour trimming unit fk 13 with automatic tool changer 8-fold • Groove trimming unit • Profile scraper // surface scraper • Buffing unit Extra Information Machine still under power

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, operating hours: 33,000 h, workpiece height (max.): 60 mm, feed rate X-axis: 25 m/min, controller model: Power Control PC22, working height: 950 mm, TECHNICAL DETAILS Feed rate: 18 - 25 m/min Working height: 950 mm Minimum working width at workpiece thickness of 22 mm: 55 mm Minimum working width at workpiece thickness of 60 mm: 100 mm Workpiece overhang: 30 mm Workpiece thickness: 8 (12) - 60 mm Edging material, strip max.: 0.4 - 20 mm Edge cross-section, strip max.: 900 mm² Edging material, coil: 0.3 - 3 mm Max. edge cross-section for PVC: 135 mm² Max. edge cross-section for veneer: 100 mm² Max. roll diameter: 830 mm MACHINE DETAILS Control system: Power Control PC22 Pneumatic connection: 7 - 8 bar Cjdpfsyc Sr Asx Aa Eegp Operating hours: approx. 33,000 h EQUIPMENT Continuous machine frame for mounting processing units Workpiece support with roller rail, extendable approx. 800 mm Glue roller drive on feed stop Glue pot lift-off at feed stop Glue pot clamping, workpiece actuated Infeed fence automatically adjustable Infeed lock pneumatically controlled Infeed device with 2 rollers Infeed extension 500 mm Automatic pressure zone adjustment Sliding carriage Pre-installed for Boomerang ZHR05 return system Workpiece support in extended scissor design Operating data collection Electric height adjustment Fixed stop on left side Workpiece transport system Top pressure Separating agent spray unit Jointing cutter unit, 2 x 3 kW Gluing station A20 Basic for coil material up to 3 mm and strip material up to 20 mm, with melting unit with granulate tank and quick-change system Cross-cutting unit, 2 x 0.8 kW, with pneumatic adjustment Slip agent spray unit Pre-milling unit 1.5 kW, pneumatically adjustable Profile trimming unit FK13, 2 x 0.4 kW Universal milling unit 4 kW, controlled, with stepless axis Multi-finishing unit MN21 automatic Finishing unit FA11, with finishing station, cleaning agent application, and buffing unit, pneumatically adjustable Noise protection Spare position for additional processing units Note: The machine is sold without consumable tools. Container loading and seaworthy packaging by the seller is not possible.

Condition: used, Multiplexer, control card, input card, control, edge banding machine, edge banding machine -Manufacturer: Homag Homatic -Type: 2-083-02-7921 -Type: 2083027921 Cedpfjcc Enxsx Aa Esgp -Number: 2x control cards available -Price: per piece -Dimensions: 130/340/H30 mm -Weight: 0.28 kg

Condition: excellent (used), Year of construction: 2021, Angular sawing plant Numerical Control PowerControl V2.1 - CADmatic 5 (Tapio ready) No. 1 Rollers table for pre-loading (useful mm 2200 x 4500 approx) Lifting table (mm) 4300 x 2200 1st Rear-pusher, with No. 4 clamps/grippers 1st Panel Saw - Max cutting width mm 4300 Max blade projection (mm) 125 Scoring Unit (max. diameter saw / power) mm 180 (Kw 2,2) Main Sawing Unit (max. diameter saw / power) mm 450 (Kw 28) Adjustable speed of the saw carriage (m/min) 1 - 150 m/min 2nd Rear-pusher, with No. 8 clamps/grippers 2nd Panel Saw - Max cutting width mm 2200 Max blade projection (mm) 125 Scoring Unit (max. diameter saw / power) mm 180 (Kw 2,2) Main Sawing Unit (max. diameter saw / power) mm 450 (Kw 28) Adjustable speed of the saw carriage (m/min) 1 - 150 m/min No. 2 Front supporting tables with Air blowing system (2 x mm 800 x 2810) Total installed power A 102 Cedpfxsx Aqdcs Aa Eegp OPTION: No. 1 Waste grinder

Condition: excellent (used), Numerical Control Power Control + Software Cadmatic 4 Professional N° 1 Infeed roller tracks (ca.) 18,000 mm + (OPTIONAL: Infeeder with chains) Lifting table (mm) 5600 x 2200 VAC loader (sliding bridge) with fan suction for loading special or delicate panels 1° Rear-pusher, with No. 6 clamps/grippers Turning device (rotating unit) at 90° 1° Panel Saw - Max cutting width mm 5600 (cutting line with air cushion) Max blade projection (mm) 170 Scoring Unit (max. diameter saw / power) mm 200 (Kw 2,2) Cjdpfxof Nkv Sj Aa Eogp Main Sawing Unit (max. diameter saw / power) mm 570 ( Kw 30) Adjustable speed of the saw carriage (QS) (m/min) 1 - 150 m/min 2° Rear-pusher, with No. 7 (+1) clamps/grippers 2° Panel Saw - Max cutting width mm 2200 (cutting line with air cushion) Max blade projection (mm) 170 Scoring Unit (max. diameter saw / power) mm 200 (Kw 2,2) Main Sawing Unit (max. diameter saw / power) mm 570 (Kw 30) Adjustable speed of the saw carriage (QS) (m/min) 1 - 150 m/min Waste evacuation system with grinder (Kw 19.5) No. 2 Front supporting tables with Air blowing system (mm 800 x 2160) Plastic wheels coated with special material to avoid scratching delicate panels Automatic unloading System of the cut panels (N° 2 roller conveyors) Typ 68/20 and Typ 58/24 + N° 3 tables with motorised belts: 2 x Typ 255/56/2 and 1 x Typ 27/56) Total power Kw 110 ca.

Condition: excellent (used), Numerical Control Power Control + Software Cadmatic 4 Professional No. 1 Infeed roller tracks (ca.) 32,000 mm Lifting table (mm) 5600 x 2200 VAC loader (sliding bridge) with fan suction for loading special or delicate panels 1° Rear-pusher, with No. 6 clamps/grippers Turning device (rotating unit) at 90° 1° Panel Saw - Max cutting width mm 5600 (cutting line with air cushion) Max blade projection (mm) 190 Cedpfx Aovnq H Esa Esgp Scoring Unit (max. diameter saw / power) mm 200 (Kw 2,2) Main Sawing Unit (max. diameter saw / power) mm 600 ( Kw 36) Adjustable speed of the saw carriage (QS) (m/min) 1 - 130 m/min 2° Rear-pusher, with No. 14 clamps/grippers 2° Panel Saw - Max cutting width mm 2200 (cutting line with air cushion) Max blade projection (mm) 190 Scoring Unit (max. diameter saw / power) mm 200 (Kw 2,2) Main Sawing Unit (max. diameter saw / power) mm 600 (Kw 36) Adjustable speed of the saw carriage (QS) (m/min) 1 - 130 m/min Waste evacuation system with grinder (Kw 19.5) No. 2 Front supporting tables with Air blowing system (mm 800 x 2160) Plastic wheels coated with special material to avoid scratching delicate panels Automatic unloading System of the cut panels: N° 2 x Liftomat HAU-A 25/12 Automatic Stacking System with 8 stations

Condition: excellent (used), Angular sawing plant Cgodpfx Aaepuh Dkj Eop Numerical Control Cadmatic 4 professional Rollers table for pre-loading No. 1 (mm 2200 x 4400) Lifting table (mm) 2200 x 4300 1st Rear pusher, with clamps No. 4 1st Panel Saw Max cutting width (mm) 4300 Max blade projection (mm) 125 Scoring Unit (max. diameter saw / power) mm 180 (Kw 2,2) Main Sawing Unit (max. diameter saw / power) mm 450 (Kw 18) Adjustable speed of the saw carriage (m/min) 0-150 2nd Rear pusher, with clamps No. 8 2nd Panel saw Max cutting width (mm) 2200 Max blade projection (mm) 125 Scoring Unit (max. diameter saw / power) mm 180 (Kw 2,2) Main Sawing Unit (max. diameter saw / power) mm 450 (Kw 18) Adjustable speed of the saw carriage (m/min) 0-150 Front supporting tables with Air blowing system No. 2 With extra long air blowing table to facilitare the evacuation of the cut panels Total power Kw 52.6

Condition: used, functionality: fully functional, machine/vehicle number: 2-017-95-2630, Motor spindle for CNC machine Weeke BOF and BAZ. - Available 7 pcs (in that quantity 2 pcs with C axis); Cgjdpfxjxnbmfj Aa Esp - 12000 - 24000 Rpm; - 16kW - HSK 63

Condition: excellent (used), Double side - Independent Machine (or 1st and/or 2nd in a line) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Panels thickness (min/max) mm 8 / 60 Working width (min/max) mm 240 / 2500 Numerical Control PC 22 Adjustable feeding speed (m/min) 10 - 40 Distance (center-axes) of the Disappearing Dogs (mm) 500 SIZING PART (for each side): Anti-chipping Milling Unit 1 x Kw 4,5 (hydro) Hogging Units KD 11 (2 x Kw 8,1) hydro EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt Glue + Quick Melt system) A3 + A34 Edge coils support (No 6 reels) Band Pressure zone "C" Rough Trimming unit 2 x Kw 0,55 Fine Trimming unit MF 20 (2 x Kw 0,55) 20° Cgsdpslikydofx Aa Eop Corner Rounding unit (Contour Trimming) FF22 (4 x Kw 0,4) max 35 m/min Profile edge scraping unit PN 20 Finish processing unit (Glue scraper + Buffing unit) FA 11 Free space

Condition: excellent (used), FULL LINE of Double-side Sizing-Milling & Edge Banding, max working width mm 2500, with automatic handling. Composed of the following machines: X04004A) Double Loader "BARGSTEDT" TBH 500/D/30/14 with central motorised roller conveyor X04004B) Turning station (90°) lengthwise to crosswise "HOMAG" Mod. TDR31/25/12 X04004C) Splitter "HOMAG" Mod. FPR620/04/15/PS/LQ to split in two parts the unique panel X04004D) Seperation Station "BARGSTEDT" X04004E) Double-side Sizing & Edge Banding machine "HOMAG" Mod. KFR 620 / 19 / QA / 25 X04004F) 1° Automatic (through-feed) Multi Borer "WEEKE" Mod. BST 500 D X04004G) 2° Automatic (through-feed) Multi Borer "WEEKE" Mod. BST 500 D X04004H) Turning station (90°) crosswise to lengthwise "HOMAG" Mod. TDR 51/25/12 X04004I) Motorized belt transfer "HOMAG" TR 10/70/12 Csdpfx Aaolikvhs Ejgp X04004L) Splitter "HOMAG" Mod. FPR620/04/15/PS/LQ to split in two parts the unique panel X04004M) Double Stacker "BARGSTEDT" Mod. TSP 420/40/30/12 BA with central motorised roller conveyor

Condition: excellent (used), Double side Sizing & Edge banding - First (1st) machine in a line Edges (tape) thickness in rolls (min/max) mm 0,3 / 3 Panels thickness (min/max) mm 10 / 60 Working width (min/max) mm 240 / 1000 Numerical Control / Software NC 21 / Homatic Adjustable feeding speed (m/min ) high speed 10 - 60 Safety and sound-proof enclosures/cabins SIZING PART (for each side): Hogging Units KD 10 (2 x Kw 6,6) EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt + Quick Melt Unit) A3 + A34 (high Speed package) Pressure zone Edge coils supporting unit (No. of reels) 2 Rough Trimming unit 2 x Kw 0,55 Fine Trimming unit 2 x Kw 0,55 (0° - 30°) Cjdpfxeifnxxs Aa Eogp Finish processing unit (Glue scraper + Buffing unit) FA 11 Milling grooving unit UF11 (1 x Kw 4) 0°-90°

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions Cgodpfx Asyqybusa Ejp End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW Cgodpfx Aaeyqx U He Eep EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: used, machine/vehicle number: 006376, Max. panel width: 1000 mm Max. panel length: 2500 mm Cedpfx Aaoyqxypj Eogp Length of conveyor: 10000 mm Panel return for edgebander: Left

Condition: excellent (used), Year of construction: 2020, Homag Edgeteq S-200 Year: 2020 Specification: Feed Speed 11m/min Machine Length 4605mm Workpiece Thickness max 60mm Edge Material Roll 0-3-3mm Edge Material Strips 0.4-5mm Joint trimming / pre-milling (44mm high blocks) Standard EVA glue unit Pressure zone with 1 main pressure roller + 2 idel rollers with pneumatic adjustment for thickness End Trim unit with pneumatic adjustment for chamfer / straight Top and bottom trimming unit with 2mm cutters Contour trimming unit with 2mm cutters Profile scraping with pneumatic adjustment with 2mm blades Additional changeable scraping heads with 1mm blades Glue Joint scraper Buffers LED indoor lighting Control system easy touch Cgodpfx Aeypm Hhsa Eep Package for construction elements Basic v Package Central Lubrication 400V 50Hz CE

Condition: excellent (used), Year of construction: 2019, Specification Cgjdpeypm Dgefx Aa Eop 2 tanks 1 cleaning station Suitable for right sided machine such as Edgeteq S-240, S-300 and S-380 400V 50Hz

Condition: excellent (used), Year of construction: 2019, Specification: Working height: 950mm Length: 4773mm Cgsdpfx Aaoypm Avj Ejp Workpiece Thickness: 60mm Edge Material Roll: 0.4-3mm Edge Material Strip:0.4-6mm Adjustable Infeed Fence Workpiece Support Feed Speed 11m/min Central Lubrication Roller Top Pressure Manual Top Pressure Adjustment Separating Agent Spray Device Joint Trimming Unit 2x2.2kw Panel Pre-Heating QA65 Application unit for PUR Pressure Zone End Trim Unit Trimming Unit Counter Trimming unit Radius Scraping Unit with 2 sets of quick change heads Glue Joint Scraping Detergent Spraying Unit Buffers 400V 50Hz CE XES 200 with 2 tanks and 1 cleaning station including collecting tray.

Condition: ready for operation (used), Year of construction: 1998, Homag Processing Center Genius BAZ20/30/14/D Electronically controlled milling and edge-banding machine, post-processing, and drilling center designed for batch production of furniture parts, solid wood, or similar materials. Base Machine: - Heavy-duty, stable machine bed with a compact linear guide system. - Aggregate carrier with linear guide system, ball screw, and digital AC servo motor for Z-axis positioning, travel distance 340 mm - Automatic central lubrication for all drives and linear guides - Designed for the attachment of various table configurations Control System: Wood Wop 5.0 - Enlarged Z-axis travel, 500 mm - Extended safety step mat - Manual through-feed table B20/30+40/…/D - Motorized width adjustment of the longitudinal console D-table - Chip conveyor belt for B../30+40/K - Stop pins for laminate overhang - Main spindle, 12 kW Csdpsx Nrk Hsfx Aa Eogp - Chain tool changer, 70 positions for B20, for HSK 63 F tools - Aggregate interface for main spindle - Electrical/electronic interface 220/24 volt - Edge gluing aggregate, 4 sides for main spindle - Melting unit with granulate container - External automatic triple edge changer - Rack changer system for aggregates and tools - Rabbet pressure zone for main spindle - Flush trimming unit for tool changer - Saw and crosscut unit for tool changer - Boring/milling unit with 4 spindles for tool changer - Lock case milling unit for rotary magazine - Vertical milling unit with tracing ring - Sanding unit with air blast nozzle - CNC programming system Wood-Wop - Post-processor for BAZ - Free-standing control panel Location: Ex works, customer site - Immediately available - Machine must be dismantled by the buyer.

Condition: used, Year of construction: 2018, max. workpiece length 4200 mm profile spindle 1 Stück main drive 15 kW HOMAG CNC Machining Center BMG310/42/F/K, Year of Manufacture 2018 ----- This machine is part of the sale of a complete window manufacturing business, Codeyn R Iajpfx Aa Eogp see stock number 1305-6979. Machines still connected and ready for demonstration Technical specifications: ----- - Gantry machine, 5-axis Drive 5C+ with 15 kW - Ceiling laser - Working dimensions 4200 mm length, 1350 mm depth - 32-position disc changer - 8-position linear changer - Fixed drilling head with 18 spindles V12/H6/S0/90 degrees - 8 consoles - 6 lift rails - Connection for 8 PowerClamp clamps - Approx. 30 vacuum clamps - 4 x PowerClamp clamps - WoodWop - Chip conveyor belt - Various small solid wood clamps, used for casement windows For a detailed description, please see the attached PDF document! ----- Price: on request! Options with additional costs: ----- - Used Leitz tools for Homag with curved tooling, compatible with SCM Windor 40 R systems #1305-6993. Price: 12.000 Euro - Barbaric vacuum lifter, manufactured in 2015. Price: 4.500 Euro - used Löwer MZP 1 mini fingerjointing press for arched windows Price: 1.000 Euro (Technical specifications according to the manufacturer, without guarantee!)

Condition: used, machine/vehicle number: 008167, X axis working area: 6000 mm Cgedpfex A Hczjx Aa Esp Y axis working area: 1750 mm Working Table: Pod and Rail Main Electrospindle power: 12 KW Number of controlled axes: 5 axes Total number of drilling spindles: 30 Total number of tool changer positions: 72

Condition: used, Year of construction: 2000, The HOMAG BOF 31/40/G is an industrial CNC machining center designed for precise sizing, drilling, and milling of panel components in furniture manufacturing. BOF series machines are robust production centers suitable for both series and flexible manufacturing of furniture parts. Cgedpfsynb N Uox Aa Eep This model is conceived as a universal production cell with options for automation and integration into HOMAG production lines.

Condition: good (used), Year of construction: 2008, functionality: fully functional, input voltage: 400 V, Equipment: CE marking, documentation/manual, HOMAG Optimat BAZ 722/42/16/K Cedpfx Ajyq Nkrja Esgp Gantry CNC machine with 2 shuttle tables Options included: Vacuum pumps 2pcs Parts positioning laser. Vacuum pads Scrap parts transporter

Condition: used, Year of construction: 2000, functionality: fully functional, NEW PRICE! Manufacturer: HOMAG Model: KFL 10/22/QE/CF Type: Double-side Sizing & Edge Banding machine Year: 2000 Cedpfx Aajuggpze Ejgp Status: Connected, test possible. Location Lithuania Basic machine Workpiece thickness 12...60 mm Workpiece width 70... mm Workpiece overhang to transport chain 40 mm Feed 10...40 m/min Power consumption Main drive 3...75 kW Height adjustment 0,2 kW Machine main drive Feed 6...30 m/min Power draw 2,2...6,9 kW Gluing unit Edging type: Straight and softforming edges Edging material height 16...65 mm Workpiece feed max. 60 m/min Contour, trimming unit CF/CS 10/11/12 Discharge valve HMA 1 Melting unit HMG 12-1x1-M-HO Gluing section for preformed parts Type of edge Straight edges drum profiles Edge material Belt from roll Snipping unit for profile parts WK 46 Saw blade (diameter 80 mm, cutting width 3.2 mm, drill hole 34 mm, number of teeth 20) Flush-trimming unit and scraping unit for performed parts Buffing unit for performed parts Specification, layout on request

Condition: excellent (used), Year of construction: 2013, Used 5-axis CNC machining center Manufacturer: Homag Model: PROFI BMG 511/40/15/F/K Year of manufacture: 2013 5-axis spindle 15 kW, Drive5C+ MPU drilling head with 30 spindles, 360° Vertical drilling spindles: 20 Horizontal drilling spindles: 10 Additional routing spindle: 6 kW Speed Pack 18-position disc tool changer D=130 below PickUP station for saw blade 350 mm Tool transfer station Workpiece length: All units: Single 4,000 mm, pendulum 2,250 mm, min. 500 mm Tool diameter 25 mm: Single 4,175 mm, pendulum 2,250 mm, min. 500 mm Workpiece width: Rear stop: 1,900 mm Front stop, all units: 1,450 mm; with tool diameter 25 mm: 1,675 mm – Workpiece thickness: – Max. 300 mm including clamping devices – Up to 60 mm with standard clamps Console table with 10 movable consoles, each with 2 suction cups, side and longitudinal stops, LED position display for vacuum suction cups 14* for laminate overhang; 10 extraction rails, connection for Power-Clamp, vacuum connection for templates SAFETY AND PROTECTIVE DEVICES: CE Compliant; SAFETY FENCING ON THE RIGHT WITH DOOR Equipment: DRILLING HEAD 30 SPINDLES: V20 / H10/ S360° “MPU” 10 HORIZONTAL SPINDLES GROOVING AND SEPARATING SAW ADDITIONAL ROUTING SPINDLE 6 KW FOR MPU DRILLING HEAD DRILLING/MILLING UNIT 4-SPINDLE FOR TOOL CHANGER Cgjdsym Am Sspfx Aa Eop MACHINING SPINDLE 15 KW DRIVE5C+ AGGREGATE INTERFACE DRIVE5C+ TOOL MEASURING PROBE FOR TOOL CHANGER SOFTWARE FOR POSITION MEASUREMENT & CNC AXIS ROTATION TOOL TRANSFER STATION 18-POSITION DISC TOOL CHANGER D=130 BELOW PICKUP STATION FOR 350 MM SAW BLADE FOR DRIVE5(C)+ COOLANT TANK FOR MACHINING SPINDLE VACUUM PUMP 300/360 M³/H Control: POWERCONTROL PC85 WITH POWERTOUCH CONTROL SYSTEM; IPC POWERPACK, OPERATOR CONSOLE FOR PROGRAM START; CAMERA SYSTEM WITH TABLET PC WOODWOP CAD/CAM INTERFACE STANDARD DOCUMENTATION AND CONTROL TEXTS: GERMAN Delivery includes only the depicted tools and HSK holders!