Used Heavy Drill Machine for sale (68,177)

Condition: used, Box column drilling machine WEBO Series- No 132 Machine No: 9 Drilling capacity 50 mm Spindle cone MK 5 - long quill throat 430 mm spindle stroke 280 mm Height adjustment of drill head 500 mm Table size Ø 725 mm Distance between drill spindle and table max. 740 mm Distance between drill spindle and clamping surface on machine base max. 1240 mm Spindle speed 55-820 rpm Feed rate level 1 0.13 - 0.2 - 0.27 - 0.4 mm/rev. Feed rate stage 2 0.6 - 0.83 - 1.17 - 1.8 mm/rev. Column diameter 300 mm Motor power 2.8 / 3.6 kW pole-changing Mains connection 380 Volt, 50 Hz - Spindle speed via 2 motor speeds and infinitely variable via variator - Manual drill head height adjustment via hand crank, clamping with clamping screws - Rotatable drill table with mechanical clamping - Table height adjustment via hand crank - Clamping surface on machine base 600 x 550 mm Top height of drill head 3020 mm Overall height drill head bottom 2520 mm Space requirement L x W x H 1400 x 780 x 2520 mm Weight 1600 kg good condition Iiodpfx Aoqa Txqsbnof

Condition: used, Column drilling machine ALZMETALL, type AB 3 ESV Machine no. 15967, year of manufacture 1977 Drilling capacity 32 mm Spindle mount MK 3 – short quill Distance from spindle nose to table 545 mm (short quill) Distance from spindle adapter to table 395 mm (MK adapter) Overhang 290 mm Quill stroke 160 mm Table size Ø 545 mm Column diameter 220 mm Spindle speed 55 – 1450 rpm, continuously variable Motor power 1 / 1.6 kW Power connection 380 volts, 50 Hz Iiodpfjharwvox Abnof - Spindle speed controlled via 2 gear stages, 2 motor speeds, and continuously variable via a variator gearbox - Pre-selection stage for high torque at low speeds - MK adapter from MK3 to MK4 - Automatic feed 0.1 - 0.2 - 0.3 mm/rev - Rotatable drilling table - Table height adjustment via hand crank - Heavy machine base with machined workpiece support surface (not original Alzmetall) - Lighting for the work area Space requirement L x W x H 1150 x 650 x 2000 mm Weight 850 kg Good condition

Condition: new, functionality: fully functional, mileage: 4 km, power: 35 kW (47.59 HP), gearing type: hydrostat, fuel type: diesel, fuel tank capacity: 60 l, color: green, overall weight: 4,800 kg, empty load weight: 4,800 kg, operation weight: 4,300 kg, mast type: duplex, Year of construction: 2025, platform length: 4,700 mm, transport length: 3,820 mm, transport width: 1,980 mm, transport height: 2,365 mm, Equipment: hammer hydraulics, hydraulics, rubber tracks, The MW1000-TX5 pile driver is a versatile and high-performance machine, designed for efficient pile installation in construction, solar farms, guardrails, and infrastructure projects. With its powerful hammer, flexible mast movement, and operator-focused design, the MW1000TX-5 provides superior control and precision, even in challenging terrains. Iedpex Tg Etefx Abnsif 90-Degree Rotating Platform: The upper body platform with the mast can rotate 90 degrees, allowing for precise pile placement without repositioning the entire machine. 15-Degree Mast Tilting: The mast can tilt 15 degrees left and right, providing greater flexibility on uneven or sloped terrains.

Condition: new, functionality: fully functional, mileage: 4 km, power: 35 kW (47.59 HP), gearing type: hydrostat, fuel type: diesel, fuel tank capacity: 60 l, color: green, overall weight: 4,350 kg, empty load weight: 4,350 kg, operation weight: 4,300 kg, mast type: duplex, Year of construction: 2025, platform length: 4,500 mm, transport length: 2,950 mm, transport width: 2,280 mm, transport height: 2,550 mm, Equipment: hammer hydraulics, hydraulics, rubber tracks, The MW1000 pile driver is a high-performance, versatile machine designed for efficient and precise pile installation in various solar park, guardrail, vineyard, and construction applications. Iiedpfxjx Tf R Us Abnjf

Condition: new, functionality: fully functional, mileage: 4 km, power: 35 kW (47.59 HP), gearing type: hydrostat, fuel type: diesel, fuel tank capacity: 60 l, color: green, overall weight: 4,750 kg, empty load weight: 4,750 kg, operation weight: 4,300 kg, mast type: duplex, Year of construction: 2025, transport length: 3,820 mm, transport width: 1,980 mm, transport height: 2,365 mm, Equipment: hammer hydraulics, hydraulics, rubber tracks, The MW1200 pile driver is a high-performance and heavy-duty machine designed for efficient and precise pile installation in a variety of construction applications. With its powerful hammer, extended mast height of 6.1 m, and adjustable settings, the MW1200 is ideal for solar farms, fencing, guardrails, and infrastructure projects. Isdpfsx Tg Dpex Abnjif

Condition: new, functionality: fully functional, mileage: 4 km, power: 45 kW (61.18 HP), gearing type: hydrostat, fuel type: diesel, fuel tank capacity: 60 l, color: green, overall weight: 5,200 kg, empty load weight: 5,200 kg, operation weight: 5,200 kg, mast type: duplex, Year of construction: 2025, platform length: 6,500 mm, transport length: 2,240 mm, transport width: 44,145 mm, transport height: 2,315 mm, Equipment: hammer hydraulics, hydraulics, rubber tracks, The MW1600-TX5 pile driver is a versatile and high-performance machine, designed for efficient pile installation in construction, solar farms, guardrails, and infrastructure projects. With its powerful hammer, flexible mast movement, and operator-focused design, the MW1600TX-5 provides superior control and precision, even in challenging terrains. 90-Degree Rotating Platform: The upper body platform with the mast can rotate 90 degrees, allowing for precise pile placement without repositioning the entire machine. Isdpfx Absx Tg Nxenjif 15-Degree Mast Tilting: The mast can tilt 15 degrees left and right, providing greater flexibility on uneven or sloped terrains.

Condition: ready for operation (used), functionality: fully functional, travel distance X-axis: 2,500 mm, travel distance Y-axis: 1,400 mm, travel distance Z-axis: 1,100 mm, spindle diameter: 100 mm, number of axes: 3, TECHNICAL DETAILS Travel range, X-axis: 2,500 mm Travel range, Y-axis: 1,400 mm Travel range, Z-axis: 1,000 mm Spindle diameter: 100 mm Table length: 2,200 mm Table width: 1,500 mm MACHINE DETAILS Drive system: Conventional Number of axes: 3 Iisdpozrmncsfx Abnef Dimensions & Weight Dimensions (L x W x H): 5,300 x 3,400 x 2,850 mm Weight: approx. 5,000 kg

Condition: used, Year of construction: 1994, bore capacity in steel (diameter) 35 mm throat 300 mm bore stroke 180 mm turning speeds 55 - 1450 U/min taper MK 4 column diameter 145 mm total power requirement 2,2 kW weight 500 kg dimensions 800 x 1000 x 2000 mm Features: - Heavy-duty pillar drill - Infinitely variable speed control (V-belt) - Automatic spindle feed * with electromagnetic engagement - Pole-changing motor - Right/left rotation of the drill spindle - Fixed drilling depth stop Isdpfx Abezu Tk Nonsif - Machine table with 2 T-slots * height-adjustable via hand crank - Coolant system - Machine vise - Drill chuck - Emergency stop

Condition: good (used), functionality: fully functional, drilling depth: 600 mm, workpiece weight (max.): 2,000 kg, travel distance X-axis: 750 mm, travel distance Y-axis: 630 mm, travel distance Z-axis: 300 mm, spindle speed (max.): 3,000 rpm, drill diameter: 35 mm, drill spindle length: 600 mm, spindle mount: MK 2, spindle stroke: 600 mm, number of spindles: 1, Equipment: rotational speed infinitely variable, Driling capacity: Ø 35 mm Driling depth: 600 mm X-axis: 750 mm Y-axis: 630 mm Z-axis: 300 mm Spindle speeds: 0 - 3000 rpm Tabel size: 1100 x 650 mm Load on table: 2000 kg max Turning table: 360° Controller: Degen AE30 Including: - Cabinet + pallet with drills - Coolingunit Iedpfszu Sp Rex Abnoif - Machine manuals Country of origin: Germany Motor power: 11,2 kVA Machine LxWxH: 350 x 120 x 175 cm Machine weight: 1300 kg

Condition: used, Year of construction: 1999, Machine number: 9114108 Weight (approx.): 150 kg Motor power: 0.71 / 1.26 kW Iiedpezd Hntefx Abnef Overhang – stand to drilling center: 600 mm Max. material height: 200 mm Table width: 1000 mm Number of drilling spindles: 4 Drill chuck: Screw-in thread Drilling depth limitation: Yes Drilling stroke: 70 mm Speeds: 1400 / 2800 rpm Workpiece clamp: Yes Drilling feed: Hand lever Working height or feed table height: 890 mm, with lighting Storage location: Nattheim

Condition: ready for operation (used), Year of construction: 1965, functionality: fully functional, travel distance X-axis: 1,600 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 1,150 mm, spindle speed (max.): 6,000 rpm, table load: 6,000 kg, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range, X-axis: 1,600 mm Travel range, Y-axis: 1,200 mm Travel range, Z-axis: 1,150 mm Spindle speed: 20–6,000 rpm Work table: 1,200 × 1,400 mm Table load: max. 6 t Isdpfozuzpaex Abnsif Please note the following: The height and weight of the asset must be taken into account when selecting the transport vehicle. There is no loading dock on site. However, a forklift or an overhead crane is available for loading. If the asset is not collected on time, a storage fee of €20.00 per lot and per day (or part thereof) will be charged. The fee must be paid before collection. The sale is made without any warranty or guarantee. The information on the technical data is based on the original offer. No liability is accepted for typographical or measurement errors. In case of doubt, please compare the information with the provided photos or inspect the item on site before the auction ends.

Condition: used, Year of construction: 2019, - Magazine loading system - Clamping table for frame parts - 3 horizontal, longitudinal drilling units from the rear - 4 vertical drilling units from above 1 Drilling machine Manufacturer: KOCH Type: BL 2500 NC select line - used - Year of manufacture: 2019 Workpiece dimensions Workpiece length 150 - 2500 mm Workpiece width 20 - 300 mm Workpiece thickness 10 - 50 mm Material: Solid wood Iiodpfezuynhex Abnjf Magazine loading system 1 with workpiece return. Workpiece insertion via 2 parallel-controlled servomotors. The number of workpieces in the magazine depends on the workpiece weight. Manual workpiece insertion Clamping table for frame parts 1 By inserting 3 support segments into the longitudinal drilling units, workpieces can be inserted manually and clamped with clamping cylinders and templates. This also allows for special workpiece dimensions. Work cycle triggering via 2 manual controls on the swappable control panel. 3 horizontal, longitudinal drilling units from the rear Construction width 160 mm Drilling motor 2 kW Longitudinal adjustment (X) with LCD display Vertical adjustment (Z) With dust extraction 4 vertical drilling units from above (supported on one side in a linear guide) Adjustable over the entire working width (X), reading LCD display. Adjustable in working depth (Y), reading LCD display One vertical clamping cylinder mounted directly on the unit Counterpieces for through-holes are available as an option. Drilling motor 1.5 kW at 50 Hz Drilling stroke 50 mm Speed 2,800 rpm Total drill length 70 mm With 4 rotary indexing heads with quick adjustment (for vertical drilling units) with fixed stops at 0 and 90 degrees Positioning control KOCH NUMERIC Basic 1 Positioning control with Beckhoff C6920 industrial PC Intel Celeron 2.2GHz CPU 2.5 320GB HDD 1x RS232, 2x USB, 1x Ethernet available 15-inch touch panel Operating system Windows 7: English User interface in English Input of all machine commands via the touch panel Software is prepared for an online connection. The configuration of the online connection (network) and commissioning are carried out by the customer or their software company. USB port on the PC 4 x Dynamic NC axis (with bearing control) for Z axes Connection data 1 Electrical connection 400 V, 50 Hz, 3 phases Voltage fluctuations max. + 6 % to - 10 % If protected by an RCD (residual current device) on the customer's side, an all-current sensitive (R CCB, Type B) RCD with a rated residual current of /= 300 mA must be used. Air connection 7 bar Dust extraction air velocity min. 30 m/s Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: good (used), Year of construction: 1980, functionality: fully functional, Gear-driven drill press, no belt changes required Very quiet and smooth operation - Drilling capacity in steel ST 60: 30 mm - Drill spindle mount: MK 3 - Drill spindle stroke: 160 mm - 9 drill spindle speeds: 90 - 1450 rpm - Overhang: 300 mm - Table with 2 T-slots - Table dimensions, swiveling: 500 x 450 mm - Table dimensions, base plate: 350 x 400 mm - Distance from base plate to spindle nose: 1100 mm - Max. distance table - drill spindle: 660 mm - Height adjustable via rack and pinion with hand crank - Column diameter: 120 mm - Drive: 380 V / 1.2 kW Iiedpjzuxxfefx Abnof - Space requirement: approx. W 600 x H 2100 x D 670 mm - Weight: approx. 350 kg - Includes drill chuck

Condition: used, Year of construction: 2018, operating hours: 500 h, Throughfeed machining, workpiece machining from below, and automatic workpiece return to the operator. 3 controlled axes: X axis - uninterrupted workpiece transport via DDT (double dynamic transport system) with a brushless motor Y axis - drilling head travel Z axis - drilling - Double "0" reference: new laser generation for detecting the start and end of the workpiece. The program can adjust the drilling from below to achieve perfect alignment in vertical and horizontal workpieces. The laser consists of a transmitter and receiver to avoid errors with dark edge materials. - Side stops with rollers consisting of a fixed and a movable part, mechanical digital readout with automatic alignment to the 0 stop for removal of up to 3 mm on the 0 line - Constant side pressing device for precise positioning on the 0 line. - Rear workpiece outlet - Automatic 4-position tool changer - No workpiece length limitation - Monitor LCD TFT 19" 5/4 - Industrial PC - Operator interface WSC with Lister, parametric tool, and parametric setup - Graphical programming CAD TPA EDI32, basic version - USB port - Storage of all files - Macro programming - Import DXF files Technical data Number of independent, vertical spindles: 12 Number of independent, horizontal spindles on the X axis: (2+2) Number of horizontal drilling spindles on the Y axis: (2+2) 1 saw (Ø 100mm) Electric spindle 5 kW with ISO30 taper (RPM 12000-24000) Max. workpiece weight: 80 kg Max. workpiece dimensions: X unlimited, Y 1200 mm, Z 50 mm Min. workpiece dimensions: X 270, Y 185 (70op), Z 4 mm Ijdpfezuxdbex Abnjif Feed rate: 25m/min Spindle speed: 3500 RPM Max. horizontal tool Ø 12mm Max. drilling depth horizontal on the X and Y axis 30mm Max. drilling depth vertical: 45 mm Max. vertical tool Ø 35mm Air consumption 2000 m3/h Extraction speed 30 m/s Extraction nozzle 2xØ. 100mm + 1xØ.50 mm Motor: 1.7 kw Compressed air: 7 bar Max. air consumption: 60 nlt/min CE STANDARDS - Office software - license - Adjustable zero point for 4-sided formatting - CE compliant - Status: 05/28/2026: approx. 500 operating hours and a new PC has been installed.

Condition: used, Year of construction: 2012, - Work area: X: 9000 mm / Y: 2700 mm - Gantry 1: 5-axis milling spindle 20/26 kW - 32-position tool changer - Gantry 2: 2x13 spindle drilling unit Technical data - Heavy-duty gantry system with 2 gantries - Gantries with drives on both sides (gantry drive) - CNC control SIEMENS 840D sl / PCU 50 with NCU 730 - Operator panel OP 15 with 15" display, mounted on a guide rail along the longitudinal axis Ijdpfxozuw Ixo Abnsif Work area / machinable cube size with tool length/diameter of 160 mm - X-axis: 9000 mm with both gantries - Y-axis: 2700 mm - Z-axis: (Standard cube size 420 mm) - Customer-specific design for workpiece thicknesses up to 60 mm - 5-axis head Equipment, Gantry 1 - 1 universal head for 5-axis milling - Milling spindle power: 20/26 kW (S1/S6) - Speed adjustable up to 24,000 rpm - Water-cooled - Tool interface HSK F63 for automatic tool changes - Thread cutting is possible! - 1 chain-type tool magazine with 32 positions - With rotary gripper for fast tool changes - Magazine fixed on the operator side Equipment, Gantry 2 - 2 head mounting brackets - Equipped with 2 heavy-duty multi-spindle drilling units each - With common dust extraction hood - Each drilling unit with 13 drilling spindles (total of 26 drilling spindles) - Individually selectable vertically - Arrangement in an L-shape - 2 angled drilling spindles adjustable from 0 - 25° - 1 right, 1 left, each approx. 2.2 kW, n= 2800 rpm - Drill chuck collet Rego Fix ER 25 M Machine table - Base frame with linear guide - 12 table traverses on a linear guide for positioning in the X-direction, individually driven and positionable via NC drives - Vacuum supply integrated into the table traverse - Each traverse is individually vacuum-monitored and linked to the machine control system Workpiece infeed function - 1 belt conveyor consisting of 4 belt strands - Width 40 mm, each traverse with lifting devices - Lifting device NC-controlled - Stroke 110 mm (+10 mm, -100 mm) - The machine should be installed in a foundation pit of approx. 300 mm - Vacuum pump Bush type: Mink MM 1322 - Suction capacity 250 m³/h - With intermediate tank 500 l for rapid vacuum generation - 2 chip transport belts under the machining area for the removal of chips and/or small swarf up to a size of max. 100 x 100 x 100 mm - Automatic central lubrication Work safety - Moving protective cabin on both gantries - Protective cabin with safety bumpers and safety light curtain system on the operator and rear sides (due to automatic table adjustment)

Condition: used, Vitap's smart solution for through-hole drilling and grooving with automatic return to the operator. Three controlled axes: - X-axis – continuous workpiece transport via a patented belt system. - Y-axis – drilling head movement, guided by rack and pinion. - Z-axis – drilling, guided by ball screw. The fewer limitations, the greater the progress! With our machine, we do not impose any limits on workpiece length. Simple TPA programming: - You can position the holes individually. - The machining operations are displayed on a virtual workpiece. - If the workpiece dimensions change, the holes can be automatically adjusted. Office software license – Power lies in tranquility. - Perhaps you have better ideas in a quieter environment? This allows you to make better use of the flexible CAD system. - With this license, you can write programs where they are developed and discussed, in the office. Color LCD TFT 19" 5/4 screen USB port for loading programs from any office workstation 3 password-protected access levels (operator, supervisor, assistance) Iijdpfx Abezutqienjf Technical data: - 9 vertical spindles, individually controllable - 2+2 horizontal drilling spindles in X - 1+1 horizontal drilling spindles in Y - 1 grooving saw unit (saw blade diameter 100 mm) - Max. workpiece thickness 50 mm - Max. workpiece weight 50 kg - Max. workpiece size: X unlimited, Y 920 mm, Z 50 mm - Min. workpiece size: X 270 mm, Y 150 mm, Z 10 mm - Workpiece transport speed: 25 m/min - Spindle speed 3,600 rpm - Max. horizontal drilling depth, X and Y axes 30 mm - Max. vertical drilling depth 45 mm - Max. vertical tool diameter 35 mm - Max. horizontal tool diameter 12 mm - Motor power 1.7 kW - CE standard

Condition: excellent (used), Year of construction: 1988, Drilling capacity in steel (diameter) 40 mm Overhang 1,250 mm Spindle mount MK 5 Drilling spindle stroke 355 mm Speed range 20 – 1200 rpm Iedozgdfbepfx Abnsif Machine weight approx. 3.0 t

Condition: good (used), bore capacity in steel (diameter) 25,0/30,0 mm throat 260 mm bore stroke 120 mm number of spindle speeds 80-1400 min-1 table surface area 410 x 390 mm Iiedpfxsuhhzhs Abnof total power requirement 0,8/1,5 kW weight of the machine ca. 250 kg dimensions of the machine ca. 0,75 x 0,6 x 1,15 m

Condition: used, Radial drilling machine REFORM, type RB 50-16 Year of manufacture: 2002 Drilling capacity in steel: max. 50 mm Tool holder: MK 5 Nominal overhang: 1600 mm Maximum overhang of the spindle to the column: 1600 mm Maximum overhang of the spindle to the column base: 1500 mm Minimum overhang of the spindle to the column: 340 mm Minimum overhang of the spindle to the column base: 240 mm Travel of the drilling head: 1260 mm Height adjustment of the arm: 600 mm Distance between clamping surface and drilling quill: max. 1100 mm Spindle speed: 25-2000 rpm Quill stroke: 300 mm Quill diameter: 80 mm Feed rate: 0.04 to 3.2 mm/rev (16 steps) Clamping surface of the base plate: 1750 x 980 mm (1650 x 840 mm) Column diameter: 350 mm Motor power, spindle drive: 4 kW Mains connection: 400 volts, 50 Hz - Spindle speed controlled via 16 gear stages with speed preselection and hydraulic gear shifting - Right and left rotation of the drilling spindle - Automatic feed via 16 gear stages with feed rate preselection and hydraulic gear shifting - Electro-mechanical height adjustment of the arm, with hydro-mechanical arm clamping - Hydro-mechanical central clamping of the head and column via push buttons - Coolant system in the machine base Machine height with drilling head at the top: max. 2840 mm Iodszupamopfx Abnjif Space requirement L x W x H: 2400 x 1000 x 2650 mm Weight: 3.5 tons Good condition

Condition: as good as new (ex-display), machine/vehicle number: G-V7-LBM2200-2S-RL-400-Schweiz, Exhibition machine Hans Schreiner long hole drilling machine with one-hand operation. Iisdpfxjvw Edqs Abnef Optimum work thanks to fixed table and movable drill head. Standard with left/right rotation, dowel drilling device and 2-speed motor including tool compartment, eccentric clamp, miter stop Technical data: Motor output 3.8 kW Voltage 400 V Table size 570 x 300 mm Max. drilling depth 150 mm Side travel 290 mm Height adjustment 140 mm Dowel drilling device 16, 20, 22, 25 mm hole spacing Max. drill holder 20 mm Speeds 1400/2800 rpm Weight 140 kg Suction connection 100 mm Packaging dimensions 855 x 600 x 1160 mm Prices subject to change, errors, printing and typesetting errors reserved

Condition: used, Year of construction: 2000, number of spindles / bore capacity in steel (diameter) / mm Iodjy S Dm Sopfx Abnoif bore stroke / mm BD13M – 5-Spindle Gang Drill / Bench Drill

Condition: used, bore capacity in steel (diameter) / mm throat / mm bore stroke / mm Isdpfxsxqrhfj Abnoif total power requirement / kW

Condition: used, Year of construction: 1988, bore capacity in steel (diameter) 50 mm arm length / mm workpiece height max. / mm Ijdpfxswt Dwas Abnoif Table dimensions: 1200x580mmTable dimensions: 1200x580mm

Condition: used, bore capacity in steel (diameter) / mm Iijdpfjy Tbv Tox Abnjf throat / mm bore stroke 70 mm total power requirement 0,9 kW

Condition: used, Year of construction: 1989, bore capacity in steel (diameter) / mm throat / mm bore stroke / mm Ijdpfx Aev H Er Hobnjif total power requirement / kW