Used Hardinge Hlvh for sale (30)

Condition: used, Hardinge HLV-H High Speed Super Precision Tool Room Lathe Max’ Distance Between Centres 18” Max’ Swing over Bed 11” Max’ Swing Over Carriage 9” Max’ Swing over Cross Slide 6” Spindle Capacity: Though Spindle - 1 1/4” 5C Round Collets - 1 1/16” 5C Hex Collets - 7/8 5C Square Collets - 3/4” With Step Chucks – 1 1/16” to 6” With Jaw Chuck (Through Spindle) - 1 5/32” With Expanding Collets 3” Variable Spindle Speeds - 125 to 3000 rev/min Tailstock M/T 2 3 Phase Electrics Todpfx Aqoy Nfqmotoc Net Weight (approx.) 750Kgs Supplied with: 2 Axis Digital Readout 4 Jaw Chuck Faceplate 3 off Multifix Tool Holders Set of Misc’ 5C Collets For Sale Jet Machinery Ltd Jet Machinery Stock No: #79017 Machine Serial Number: HLV-H14793T Cost: £8,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, table length: 1,200 mm, table width: 600 mm, spindle speed (max.): 12,000 rpm, table height: 560 mm, table load: 900 kg, Machine with just revised spindle, never used after Tsdsrb Amljpfx Aqtoc Connected to power and available for inspections and tests Lubrication through spindle 30 Tools Heidenhain 530

Condition: used, Year of construction: 2011, Used 2011 Hardinge Bridgeport XR760. Supplied with Heidenhain iTNC 530 Control, 12,000 RPM Spindle with Through Spindle Coolant, 30 Station ATC, Renishaw spindle and table probing, Swarf Conveyor, Coolant Equipment & Manual Set. SPECIFICATION: TRAVELS: X Axis 760 mm, Y Axis 610 mm, Z Axis 610 mm Spindle Gauge Plane to Table (~ max) 710 mm, Spindle Gauge Plane to Table (~ min) 100 mm TABLE: Length 1000 mm, Width 600 mm T-Slot Width 18 mm, T-Slot Centre Distance 100 mm, Number of Std T-Slots 5, Max Weight on Table (evenly distributed) 900 kg SPINDLE: Max Rating 25 kW (S6 40%), Max Speed 12,000 rpm, Max Torque 159.2 Nm, Taper BT 40 Through Spindle Coolant, Coolant Flow Rate at Cutter 160 L/min, Through Spindle Coolant Pressure 20 bar (Std) FEEDRATES: Rapid and Jog (Max.) 20 m/min Cutting Feed Rate (Max.) 20 m/min BALL SCREWS: X & Y Axis 45 x 16 mm Z Axis 45 x 12 mm Tjdpfxozzairs Aqtjc TOOL CHANGER: Type Rapid ATC, Capacity 30 Max Tool Diameter 125 mm (adjacent pocket), 80 mm Tool Length Max. 300 mm Tool Weight Max. 7 kg COOLANT & CHIP MANAGEMENT: Swarf Conveyor, Coolant Capacity 355 L Wash Down Standard, Wash Gun Standard, Cutter Air Blaster Standard Washdown Flow Rate 140 L/min ACCURACY – ISO 230-2: Positioning Accuracy 0.010 mm Repeatability 0.004 mm GENERALS: Machine Dimensions (W x D) 2528 x 3000 mm Air Required 4.9 cfm Power Supply 25 kVA / 415 V / 3 Phase / 50 or 60 Hz Control: Heidenhain iTNC 530 Spec: X760 Y610 Z610 mm | 12000RPM | BT40 Accessories: Renishaw Probing, Through spindle coolant, 30 Position Side mount tool changer, Swarf conveyor, Chilled 12000RPM Spindle

Condition: used, Year of construction: 2011, Used 2011 Hardinge Bridgeport XR300 5AX. Supplied with Heidenhain iTNC 530 Control, 12,000 RPM Spindle with Through Spindle Coolant, Renishaw probing, 30 Station ATC, Swarf Conveyor, Coolant Equipment & Manual Set. SPECIFICATION: TRAVELS: X Axis 410 mm, Y Axis 610 mm, Z Axis 500 mm A Axis +30° to -120°, C Axis Continuous 360° TABLE: Diameter 300 mm Max Swing Diameter 300 mm, Max Weight on Table (evenly distributed) 100 kg Todpfxozzax Te Aqtjc SPINDLE: Max Rating 25 kW (S6 40%), Max Speed 12,000 rpm, Max Torque 159.2 Nm, Taper BT 40 FEEDRATES: Rapid and Jog (Max.) 36 m/min Cutting Feed Rate (Max.) 20 m/min Rotary Axis Speed 25 rpm BALL SCREWS: X & Y Axis 45 x 16 mm Z Axis 45 x 12 mm TOOL CHANGER: Type Rapid ATC, Capacity 30 Max Tool Diameter 125 mm (adjacent pocket), 80 mm Tool Length Max. 300 mm Tool Weight Max. 7 kg COOLANT & CHIP MANAGEMENT: Swarf Conveyor, Coolant Capacity 355 L Wash Down Standard, Wash Gun Standard, Cutter Air Blaster Standard Through Spindle Coolant Coolant Flow Rate at Cutter 160 L/min Through Spindle Coolant Pressure 20 bar (Std) Washdown 140 L/min GENERALS: Machine Dimensions (W x D) 2528 x 3000 mm Air Required 4.9 cfm Power Supply 25 kVA / 415 V / 3 Phase / 50 or 60 Hz Control: Heidenhain iTNC 530 Spec: X410 Y610 Z610 mm A360| 12000RPM | BT40 Accessories: 5 axis Table, Renishaw Probing, Side Mount Tool Changer, Swarf conveyor

Condition: used, Year of construction: 2008, operating hours: 48,899 h, HARDINGE BRIDGEPORT XR 1600 MACHINING CENTER YEAR: 2008 MANUFACTURER: HARDINGE TAIWAN PRECISION MACHINERY LDT MODEL: XR 1600 CNC: HEIDENHAIN iTCN 530 Features Axis Travels: X-axis: 1600 mm Y-axis: 700 mm Z-axis: 610 mm Rapid Traverse Rates (X/Y/Z): Up to 36 m/min Table: Dimensions: 1700 mm x 700 mm Maximum Load Capacity: 1500 kg Spindle and Tool Holder: Spindle Taper / Tool Holder: ISO 40 (BT40/DIN standard) Tedpjz Dv S Sefx Aqtsc Spindle Speed: 12,000 rpm Motor Power: 22 kW / 30 HP Automatic Tool Changer (ATC): Capacity: 24 positions Type: Swing arm type. Machine comes with manuals and CE declaration of conformity. All technical data provided is indicative and may be subject to change without prior notice, and therefore should not be considered binding.

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, turning diameter over cross slide: 290 mm, turning length: 330 mm, turning diameter: 229 mm, spindle bore: 47 mm, spindle speed (max.): 5,000 rpm, travel distance X-axis: 138 mm, controller model: Fanuc GE 18i-T, Hardinge Conquest T42 CNC turning center (2000) Controller: GE Fanuc Series 18-T, live tooling, C-axis option noted, tailstock included, 12-station turret, Spindle bore 47.6 mm, spindle speed 5,000 rpm, Tedpfx Aqjyzbivjtjc Max turning/machining diameter 229 mm, Max turning length 333 mm, X travel 138 mm, Z travel 350 mm.

Condition: used, Hardinge Talent Slant Bed CNC Lathe Model TI. S/No. 4500117 with Fanuc OT-B CNC Control, 10 Position Tool Turret, Tailstock, Hardinge Collet Chuck and Collets, Acrovu Feedmaster CNC Barfeed 5m Long, Kitagawa B-205 Powered Chuck Location: These lots are located in Andover, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. Tsdpfx Aqezy Rafstoc

Condition: not inspected (used), Year of construction: 2003, turning length: 380 mm, turning diameter: 284 mm, spindle speed (max.): 5,000 rpm, overall weight: 2,300 kg, siemens maximum spindle speed: 5,000 RPM Tsdex Rbwxjpfx Aqtsc VDI turret, 12 stations tooling chip conveyor

Condition: used, Year of construction: 2014, Hardinge GS200 CNC Lathe 2010 Hardinge GS200 CNC slant bed lathe equipped with Fanuc Series Oi-TD control. ----- Control Fanuc Series Oi-TD CNC Control ----- Capacity Chuck Size: 3 Jaw Bar Capacity: 52mm Maximum Swing: 457mm Maximum Cutting Diameter: 284mm Maximum Cutting Length: 406mm Distance Between Centres: Not specified ----- Main Spindle Maximum Spindle Speed: 5,000 RPM ----- Turret Number of Stations: 12 ----- Axis Travels X Axis Travel: 218mm Z Axis Travel: 406mm ----- Accessories Hydrafeed Multifeed 65 Barfeed Swarf Conveyor Control: Fanuc Spec: Spindle bore 52 mm | Max Swing 457 mm | Travel X 218 Z 406 mm Tjdpoylchtofx Aqtsc Accessories: Tailstock, parts catcher & 8" Power Chuck, Swarf conveyor, Collet chuck

Condition: excellent (used), Year of construction: 2007, Hardinge Talent 6/45 2 Axis CNC Turning Centre (2007) Siemens 810D Control (CCU3) Spindle Motor 11kW VDI30 Turret Spindle Speeds to 6000rpm Max. Turning Lenth 381mm Max. Turning Dia. 284mm Max. Swing over Bed 457mm X Axis Travel 228mm Z Axis Travel 406mm 2800kgs *For sale with Jet Machinery Ltd* Jet Machinery Stock No: #79161 Machine Serial Number: BLAA7E0070 Tedpfxsyvqdfe Aqtsc Cost: £13,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: used, 10’-0” x 84” HARDINGE CONICAL BALL MILLS MILL SPECIFICATION Model : 10’-0” x 84” HCBM Overall Dimensions : 3050 mm diameter x 5185 mm long. Installed Power : 400 kW Absorbed Power : 320 kW Mill Speed : 20 rpm Lining : Chrome Iron Cast Liner Plates Media : Steel Balls (30 tonne required) Drive : Girth Gear and Pinion, Gearbox and Slip Ring Motor Trunnion Bearings : No.1 Mill - Cooper Split Roller Bearings No.2 Mill – White Metal Bearings The mills were operated by British Chrome & Chemicals Ltd (later Elementis Chromium), at their site in Cleveland, UK, processing Chrome Ore to a fineness of 99% passing 45 µm. The first mill, with the white metal bearings, was installed in around 1970. Todpfx Aqszvgdlstec The second mill, with the Cooper Split Roller Bearings was installed in 1980. This mill is offered with a new set of Cooper Trunnion Bearings. Both mills were in operation until the site closed in 2009 and have been in storage ever since. Equipment is offered in "as is" condition with no warranty given or implied. PPDS can offer full refurbishment services. Inspection is invited at our premises in Uttoxeter, Staffordshire, United Kingdom (close to East Midlands, Birmingham and Manchester airports). Powder Process Design Services Ltd has been supplying equipment and systems to the industrial minerals sector for over 20 years. We specialise in the design and supply of minerals processing systems using a combination of new and s/hand refurbished equipment. With approaching 40 years experience we aim to deliver projects that meet and indeed exceed expectations. We have satisfied customers throughout the world, including, the United States, South America, New Zealand, South Africa the Middle East and the UK and Ireland. Please check out our other listings and subscribe to our stock list.

Condition: good (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: NVLA7K0128, travel distance X-axis: 480 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 330 mm, controller manufacturer: Fanuc, controller model: 0i-MC, total length: 1,575 mm, total width: 2,168 mm, table width: 400 mm, table length: 600 mm, overall weight: 3,000 kg, spindle speed (max.): 10,000 rpm, spindle motor power: 7,500 W, spindle nose: BT40, number of spindles: 1, number of slots in tool magazine: 16, Equipment: rotational speed infinitely variable, BRIDGEPORT HARDINGE GX480 Vertical Machining Centre. New 2007 With Coolant, Interlocked guards, Low Volt Light FANUC 0i-MC Control Machine Dimensions: 1575 x 2168 mm Machine Weight 3000 kg Tedpfx Aqjxgqwdstjc Spindle Motor Power 7.5 kW Spindle Speed 10000 rpm Table Size 600 x 400 mm Tool Change Capacity 16 Station Tool Size BT40 Traverses XYZ 480 x 400 x 330 mm

Condition: like new (used), Year of construction: 2021, Traverses X Y Z: 710 x 400 x 430mm, Table 800 x 400mm, Tsdpfxjyt E Uxs Aqtsc table load 300kgs, Spindle speed 12,000rpm, Spindle taper CAT40, 5.5kW Spindle motor, FANUC Oi , 20 Station ATC, Coolant, Low Volt light, swarf conveyor

Condition: used, Year of construction: 2006, Technical details: turning diameter over bed: 284 mm turning dia. over face-slide: 380 mm turning length: 381 mm x-axis: 153 mm longitudinal traverse (z-axis): 406 mm control: Siemens 810D revolution per minute: 5000 U/min spindle bore: 52 mm tool turret - number of stations: 12 Stationen / Stations operating hours - idle run: 78000 h electrics - voltage/frequency: 400/50 V/Hz Tedpfozrlvlox Aqtoc total power requirement: 11 kVA Weight approx.: 2,8 t dimension machine approx.LxWxH: 3,0 x 1,6 x 1,8 m The machine is equipped with a C-axis, enabling the use of driven tools. *

Condition: used, HARDINGE Conical Ball Mill 6’-0” dia x 36” ball mill for the dry grinding of industrial minerals. Tjdpfx Aezvgvnoqtsc Mill fitted with Manganese steel liners for operation will steel ball grinding media. White Metal Bearings on trunnions. 90 kW Motor fitted (could be reduced to 75 kW). Mill with countershaft drive but could be converted to gearbox.

Year of construction: 2017, condition: ready for operation (used), X-axis: 607mm, z-axis: 286mm, spindle speed: max. 6000/min, control: Fanuc 32i A, length: 4600mm, width: 1600mm, height: 2700mm, weight: 2.1t, operating hours: 34,536h. With automation FMB Unirobot LR MATE 200iD7L-P2TB, grinding spindle Jäger HF-Spindle, chuck MicroCentric 4-410-3-QC, MARPOSS measuring system with automated dimensional compensation, oil mist filter S400, belt filter Knoll KF110/500, hinged belt conveyor 320 S1 and other accessories. On-site inspection is possible. Tsdpfx Aev Uz Akoqtsc

Year of construction: 2013, condition: ready for operation (used), X-axis: 607mm, z-axis: 286mm, spindle speed: max. 6000/min, control: Fanuc 32i A, length: 1850mm, width: 1750mm, height: 1750mm, weight: 2.1t, operating hours: 59,861h. With automation FMB Unirobot MH5LS-SP, grinding spindle Jäger HF-Spindle, chuck MicroCentric 4-410-3-QC, MARPOSS measuring system with automated dimensional compensation, oil mist filter S400, Liqui gravity filter UR1020 with clean tank and other accessories. On-site inspection is possible. Todpfx Asv Uz Adoqtsc

Condition: excellent (used), Year of construction: 2008, 3-axis CNC Lathe HARDINGE GS 250M CNC Fanuc Oi-TC Spindle hours: 6000h Specifications: Max swing over bed: 595 mm Max turning diameter: 356 mm Tedpfx Ajykbareqtsc Turning length: 558.8 mm X-axis travel: 271 mm Z-axis travel: 600 mm Bar capacity: 78 mm Spindle bore: 89 mm Spindle speed: 3500 rpm Spindle power: 18.5 kW Spindle nose: A2-8’’ Options: 1 turret with 12 driven positions in VDI 40 C-axis with 360,000 positions 2 driven tools Fully programmable tailstock Automatic tool measurement probe Parts catcher 2 fixed tool holders 2 driven tool holders 1 3-jaw chuck 254 mm Tonfou

Year of construction: 2021, condition: ready for operation (used), X-axis: 607mm, z-axis: 286mm, spindle speed: max. 6000/min, control: Fanuc 32i A, length: 1850mm, width: 1750mm, height: 1750mm, weight: 2.1t, operating hours: 14,841h. With FMB Unirobot GP7-5Pkhs automation system, Jäger HF spindle grinding spindle, MicroCentric 4-410-3-QC chuck, MARPOSS measuring system with automated dimensional compensation, S400 oil mist filter, Knoll KF110/500 belt filter, 320 S1 hinged belt conveyor and other accessories. On-site inspection is possible. Tsdpfxsv Uz Aqe Aqtec

Condition: good (used), Year of construction: 2007, operating hours: 30,000 h, CNC Lathe Hardinge Quest 6/42 SP Technical Data and Scope of Supply TECHNICAL DATA Manufacturer: Hardinge Tjdpfsxflprex Aqtoc Model: Quest 6/42 SP Year of manufacture: 2007 Control: GE Fanuc 18i-TB Supply voltage: 400 V Phases: 3 Frequency: 50 Hz Machine current: 78 A Spindle drive: 44 A Control voltage: 115/24 V Operating hours: approx. 30,000 h Spindle mount: A2-5 Bar capacity: 42 mm Chuck size: 150 mm Max. workpiece length with collet: 381 mm Max. workpiece length with chuck: 270 mm Max. turning diameter: 309 mm X-axis travel: 89 mm Z-axis travel: 406 mm Rapid traverse X-axis: 28 m/min Rapid traverse Z-axis: 38 m/min Turret: 12 station VDI 30 Indexing time: 0.1 s Machine length: 2,576 mm Depth: 2,025 mm Height: 1,905 mm Weight: approx. 5 t SCOPE OF OFFER Includes (not exhaustive): - CNC lathe Hardinge Quest 6/42 SP - Toolholder set - Chip conveyor - Transformer - Chip tray - Renishaw probe For the exact scope of supply, please refer to the photo documentation. The CNC Lathe Hardinge Quest 6/42 SP with Fanuc 16i/18i/21i control system from 2007 is a high-precision machine designed for a wide range of turning operations. It features a robust A2-5 spindle mount, a 42 mm bar capacity, and a 150 mm chuck, allowing flexible machining of different workpiece sizes. With a maximum turning diameter of 309 mm, even larger components can be machined reliably. The axes provide generous travel ranges of 89 mm (X) and 406 mm (Z), as well as high rapid traverse speeds, ensuring maximum productivity. The 12-station VDI 30 turret with an extremely short indexing time of 0.1 seconds guarantees fast tool changes and minimizes downtime. Thanks to the solid construction and the proven Fanuc control, the Hardinge Quest 6/42 SP is ideally suited for series production with the highest accuracy demands. No guarantee is given for the correctness, completeness or currentness of the information provided.

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, spindle speed (max.): 6,000 rpm, travel distance X-axis: 607 mm, travel distance Z-axis: 286 mm, controller model: Fanuc 32i A, grinding spindle speed: 30,000 rpm, The offer includes a CNC hard turning lathe with FMB automation! The machine is from year of manufacture 2013, but it was only commissioned in 2017 (showroom machine)! HARDINGE GT27SP GG-134HS TECHNICAL DETAILS X-axis travel: 607 mm Z-axis travel: 286 mm Max. spindle speed: 6,000 rpm Number of axes: 2 MACHINE DETAILS Control: Fanuc 32i A Dimensions & Weight Machine dimensions with robot cell (L x W x H): 4,600 x 1,600 x 2,700 mm Weight: approx. 2,100 kg Operating hours: 34,536 h EQUIPMENT MARPOSS measuring system MicroCentric 4-410-3-QC chuck Jäger HF spindle (spindle speed: 30,000 rpm) Oil mist filter S400 Spindle cooling possible FMB Unirobot LR Mate (Serial number: E-83200 (robot) / E15X36204 (controller), year of manufacture: 2015) Robot model: FANUC LR MATE 200iD7L-P2TB Controller: FANUC R30iB Max. part feed: 70 mm Axes: 6 Robot cell weight: approx. 1,000 kg GENERAL EQUIPMENT Knoll filter system KF110/500 (capacity: 500 l) Grinding spindle holder Grinding wheel arbor RINECK Reversing station in robot cell Feed conveyor for raw/finished parts 2,900 mm 2x MAS-MEX20-GT27-1-S385H adapters Todpox I A Hpofx Aqtoc 2x MAS-MEX20 turn sleeves 2x MAS-turn rings 2x Hydro-expansion holders for internal turning tools Holder for turning tool + turning tool MARPOSS probe with holder

Condition: ready for operation (used), Year of construction: 2003, operating hours: 28,000 h, functionality: fully functional, turning diameter: 309 mm, spindle speed (max.): 6,000 rpm, travel distance X-axis: 89 mm, travel distance Z-axis: 406 mm, controller model: Fanuc Typ 18i-T, TECHNICAL DETAILS Maximum turning diameter: 309 mm Spindle speed range: 25 – 6,000 rpm Travel in X-axis: 89 mm Travel in Z-axis: 406 mm Collet diameter: 42 mm MACHINE DETAILS Control system model: CNC Fanuc Type 18i-T Spindle motor drive power: 11 kW Operating hours: 28,000 h Machine weight: approx. 5,000 kg EQUIPMENT C-axis Y-axis 12-station turret VDI 30 Powered tools at each station Power chuck, diameter 140 mm Hydraulic steady rest Workpiece collection system Chip conveyor Coolant system Tjdezu Rz Eepfx Aqtjc

Condition: excellent (used), Year of construction: 2004, functionality: fully functional, Controller GE FANUC 21i-TB Swing dia 533 mm Turning dia 340 mm Turning lenght 355 mm X travel 209 mm Z travel 355 mm Spindle hole D50,8 mm Spindle speed 5000 rpm Tjdpevw Uqaefx Aqtjc Chuck size max. D200 mm Turret 12-fold Rapid speed 30 m/min Spindle power 11 kW Spindle face A2-6 Tool holder type VDI30 C axis 0,001 degree (programmable) Dimensions LxWxH = 2300 x 1700 x 1700 mm Weight ca 3000 kg Features, accessories - Hydraulic chuck - Short barfeeder EMT Super 80 - Manual Guide in FANUC Software - Drive tool turret and C axis - Tailstock - Part catcher - Manuals Very good condition. The lathe works accurately and run quitely. Ready to buy immediately.

Year of construction: 2006, condition: ready for operation (used), Table dimensions X/Y: 1370mm/660mm, travel X/Y/Z: 1250mm/660mm/635mm, speed: 8000rpm, spindle mount: BT40, tool positions: 32, spindle-table distance: 790mm, control: Siemens 810 T. Documentation available. On-site inspection is possible. Tjdev Ubp Dspfx Aqtjc

Condition: used, Year of construction: 2005, CNC Machining Center HARDINGE BRIDGEPORT XP610 (Year 2005) Condition: Good, technically sound. Manufacturer: Hardinge / Bridgeport (USA / UK) Model: XP610 Year of manufacture: 2005 A compact and reliable CNC vertical machining center designed for precise milling, drilling, and tapping of metal parts. The Bridgeport XP series is known for its high accuracy, robust construction, and reliable control system, making it an excellent solution for manufacturing processes where precision and repeatability are crucial. Main technical specifications: (according to Hardinge Bridgeport XP610 model specifications) Tedpfxjxqp Ene Aqtoc Control system: Heidenhain iTNC 530 Travel (X / Y / Z): 610 × 510 × 510 mm Table size: 800 × 520 mm Max. table load: 500 kg Spindle speed: up to 10,000 rpm Spindle taper: BT40 Tool changer: 20 positions (automatic) Spindle motor: 11–15 kW Cooling: integrated coolant system Power supply: 400 V / 50 Hz Machine weight: approx. 6,000 kg Application: The Hardinge Bridgeport XP610 is designed for precision machining of components and parts: - Metal, aluminum, copper, and brass workpieces - Tool and die manufacturing - Production of mechanical components and industrial parts Suitable for both small batch and series production where a precise, stable, and repeatable result is required. If you have any further questions, please feel free to contact us.