Used Gildemeister As 67 for sale (235)

Condition: good (used), Year of construction: 2007, operating hours: 88,040 h, functionality: fully functional, machine/vehicle number: 07400003691, turning diameter: 120 mm, spindle bore: 118 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 30 m/min, total height: 2,500 mm, total length: 5,500 mm, total width: 2,500 mm, overall weight: 11,000 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D POWERLINE, DMG GILDEMEISTER TWIN 102 CNC Turning and Milling Center - Recorded spindle hours: 43,558 - Spindle speed range: 3,200/5,000 rpm - Swing diameter: 270 mm - Spindle distance: 900 mm - X1 axis travel: 290 mm - Z1 axis travel: 650 mm - X2 axis travel: 180 mm - Z2 axis travel: 650 mm - Y1 axis travel: ±40 mm - Z3 axis travel: 670 mm - X3 axis travel: 175 mm - Max. bar diameter: 100/104 mm - Number of driven tools per tool turret: 12 - Including chip conveyor, with 2 tool turrets (each with 12 tool stations), main and counter spindles, as well as foot switches Djdpfx Aoyaqgyjc Nokh Attention, the machine has the following defects: - The B-axis is defective (mounted on turret 1) - Guideways and drives show age-related wear - X2 axis (guide rails) runs slightly out of alignment by approximately 0.03 mm (should be re-measured) - Occasionally, axis reference value setting in the control system fails - The hydraulic pump was replaced after a failure and is now installed externally as a standalone unit FCA D-58256 Ennepetal, loaded on truck at a mutually agreed date at the end of February 2026.

Condition: good (used), Year of construction: 2008, operating hours: 72,899 h, functionality: fully functional, machine/vehicle number: 07510001241, turning length: 1,185 mm, turning diameter: 640 mm, spindle speed (max.): 12,000 rpm, workpiece weight (max.): 150 kg, total height: 3,040 mm, total length: 7,800 mm, total width: 4,100 mm, overall weight: 16,500 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D, DMG GILDEMEISTER GMX 250 LINEAR CNC Turning and Milling Center - Recorded spindle hours: 39,361 - Swing diameter: 640 mm - Counter spindle turning diameter: 400 mm - Spindle distance: 1,500 mm - X1 axis travel: 550 mm Dksdpfeyaqczex Ac Nsh - Y1 axis travel: 180 mm - Z1 axis travel: 1,185 mm - B1 axis travel: 240° - X2 axis travel: 180 mm - Z2 axis travel: 1,050 mm - Z3 axis travel: 1,150 mm - Spindle speed range: 3,200/4,000 rpm - Rapid traverse rate, Slide 1 (X/Y/Z): 40/24/70 m/min - Rapid traverse rate, Slide 2 (X/Z): 24/36 m/min - Rapid traverse rate, Slide 3 (Z): 36 m/min - Tool holder: HSK 63 - Spindle speed: 12,000 rpm - Number of tool stations in chain magazine: 40 stations - Incl. tool holders mounted on the turret - Incl. bar loader, manufacturer: COCCHE GIOVANNI, type: CNC-DB 110, year of manufacture: 2008, serial number: CNCDB-08.306, weight: 1,500 kg Note: The machine has the following defects: - The hydraulic unit is faulty – it needs to be repaired - The Q2 axis (milling spindle tool changer) fails frequently - X2 axis (guideways) moves slightly askew - The linear guides and drives show wear commensurate with age Attention: A vehicle with 3,000 mm transport width is required for transport! FCA D-58256 Ennepetal, loaded onto truck at a mutually agreed date at the end of February 2026.

Year of construction: 1982, condition: ready for operation (used), A CNC lathe Gildemeister including a chip conveyor and a Forkat chuck is available. 1) Gildemeister NEF CT 60, year of manufacture: approx. 1982, distance between centers: 1000mm, turning length: 1000mm, max. turning diameter: 460mm, center height: 300mm, bed width: 450mm, spindle bore: 107mm, speed: 3015rpm, tool stations: 12, quill diameter: 100mm, quill stroke: 180mm, machine dimensions X/Y/Z: approx. 5400mm/2100mm/2000mm, weight: approx. 7000kg. 2) Chip conveyor Allweiler GB 30L 38L. Without Filter. Documentation available. An on-site inspection is possible. Dodpfx Acoydp Azj Nokh

Condition: used, Year of construction: 2007, controller manufacturer: Siemens, controller model: 840 D, _____ Description: Year of manuf. : 2007 Control : Siemens 840 D Turning diam. : 250 mm Turning length : 650 mm In General: Year of construction:2007 Control:Siemens 840 D Bar capacity:65 mm Turning diameter:350 mm Turning length:650 mm Main spindle: Technology:Motor spindle Dedpfxeyamflo Ac Nokh Speed:5,000 rpm Power max.:35 kW Torque max.:370 Nm C-axis:0.001 Bar capacity:65 mm Chuck:Hainbuch Spanntop size 65 Clamping cylinder:Hollow clamping cylinder Sub spindle: Technology:Motor spindle Speed:5,000 rpm Power:26 kW Torque:290 Nm C-axis:0.001 Chuck:Hainbuch Spanntop size 65 Clamping cylinder:Partial hollow clamping cylinder Z-axis:670 mm X-axis:175 mm Tool carrier i (X/Y/Z): Technology:Tool turret, 12 stations Tool holder:VDI 30 Tool drive:4,000 rpm, 11 kW, 28 Nm X-axis:300 Y-axis:80 mm ( +/- 40 mm) Z-axis:650 mm Tool carrier II (X/Z): Technology:Tool turret, 12 stations Tool holder:VDI 30 Tool drive:4,000 rpm, 11 kW, 28 Nm X-axis:180 Z-axis:650 mm Equipment: Chip disposal:Chip conveyor Coolant supply:IKZ system Measuring systems:Direct in all X-axes (glass scales) Bar loader:IRCO Breuning Part removal:Finished part gripper + indexing belt Emulsion mist separator:Mechanical Set-up mode:Electronic handwheel

Condition: used, Year of construction: 2007, Number of controlled spindles (C axes): 2 Number of controlled axes: 8 Number of channels: 3 Max. bar diameter: 65 mm Bore in tie rod: 75 mm Chuck diameter: 175 mm Spindle nose: 140 mm Max. speed: 5,000 rpm Nominal torque: 191 Nm Nominal power: 20 kW DATA FOR THE W2 AXIS OF THE COUNTER SPINDLE Stroke: 690 mm Rapid traverse: 30 m/min Max. acceleration: 5 m/s² Nominal force: 2,400 N X1 AXIS DATA Stroke: 165 mm Rapid traverse: 40 m/min Max. acceleration: 10 m/s² Nominal force: 2,400 N Z1 AXIS DATA Stroke: 678 mm Rapid traverse: 30 mm Max. acceleration: 5 m/s² Nominal force: 5,000 N Y1 AXIS DATA Stroke: 80(+50/-30) mm Rapid traverse: 30 m/min Max. acceleration: 5 m/s² Nominal force: 5,000 N X2 AXIS DATA Stroke: 165 mm Rapid traverse: 30 m/min Max. acceleration: 5 m/s² Nominal force: 5,000 N Number of tool stations: 12 Dsdpfxoydfq Ij Ac Nokh Tool holder diameter: 30 mm Driven stations: 12 mm Max. speed of driven tools: 4,000 rpm

Condition: used, Year of construction: 2005, turning diameter 640 mm turning length 1.185 mm control SINUMERIK 840D swing diameter 640 mm distance of spindle heads 1500 mm slide I: X1 / Y1 / Z1 / B slide travel X-axis 550 mm slide travel Z-axis 180 mm Z- Travel 1.185 mm B - axis 240 ° feed x-axis 0 - 40.000 mm/min feed y- axis 1 - 24.000 mm/min Feed z- axis 1 - 70.000 mm/min feed B-axis 1 - 20 1/min rapid traverse X/Y/Z 40 / 24 / 70 m/min feed capacity X/Y/Z S6: 7,00/11,00/7,50 kN tool taper HSK 63 turning speed milling-spindle 10 - 12.000 1/min power capacity at 100 % load 13,20 kW power capacity at 40 % load 22,00 kW torque milling spindle 60 / 100 Nm no. of workpieces in the magazine 46 Stück tool length - max. 350 / 200 mm tool diameter 80 mm wotkpiece diameter with 2 vacant positions 120 mm weight of tools max. 6 / 10 kg slide II: X2 / Z2 slide travel X-axis 180 mm Z- Travel 1.050 mm feed x-axis 1 - 24.000 mm/min Feed z- axis 1 - 36.000 mm/min Dsdpfjydfllex Ac Njkh rapid traverse x + z axis 24 / 36 m/min feeding force S6: 11,00/9,00 kN turret (x-stations) 12 tool taper DIN 69880 Ø40 Driven tools - quantity 12 Driven tool turning speed 1 - 4.000 1/min power capacity at 100 % load 10,70 kW torque S1: 32 Nm Slide III - longitudial travel Z3 mm Z- Travel 1.150 mm Feed z- axis 1 - 36.000 mm/min rapid traverse Z-axis 36,00 m/min feed capacity Z - axes S6: 13,00 Nm Main spindle ISM90 turning speed main-spindle 10 - 4.000 1/min power capacity at 100 % load 36,00 kW power capacity at 40 % load 45,00 kW max. torque at 40% / 100% load 800 / 630 Nm spindle bore 80 mm turning speed opposed-spindle 10 - 5.000 1/min power capacity at 100 % load 21,00 kW power capacity at 40 % load 28,00 KW max. torque at 40% / 100% load 320 / 240 Nm spindle bore 80 mm total power requirement 70,00 kW weight of the machine ca. 20,00 t dimensions of the machine ca. 8,50 x 4,50 x H3,10 m Machine with SIEMENS SINUMERIK 840D control, main- and counter-spindle, chip conveyor, dust exhauster, DMG-automation WH10top. Main-spindle ISM90: hollow clamping device, C-axis, 3-jaw hydraulic chuck SMW-AUTOBLOK KNCS-NB-315-91 Counter-spindle ISM76: closed center clamping device, C-axis, 3-jaw hydraulic chuck SMW-AUTOBLOK KNCS-NB-315-91 Pick-up device with integrated conveyor belt, automatic protective cover, differential pressure clamps. Incl. pump-frame for coolant - Pump 1: 17 l/min at 80bar - Pump 2: 20 l/min at 8bar - Pump 3: 40 l/min at 20bar Without coolant unit. Was connected to a central coolant-system. Accessories: Hainbuch collet chuck incl. collets Ø30,45,50,55,60,65,72,82,85,90 1 piece workpiece pick-up-gripper for turret

Condition: used, Hydraulic self-centering steady rest, luenette, lynette SMW AUTOBLOK Hydraulic steady rest with hydrostatic bearings Dodpfx Asiv Irlsc Nokh Suitable for GILDEMEISTER / MAX MÜLLER lathe MD 5 Type: SLK 8-70 N Clamping range: 8 to 70 mm Operating pressure: approx. 60 bar steady rest base: 245 x 240 mm Type of construction: stationary - 3 pieces roller bearing Ø 35 mm - roller width 18 mm - hydraulic self centering dimension L x W x H: 350 x 250 x 550 mm dead weight: 65 kg good condition

Condition: used, Year of construction: 2008, functionality: fully functional, turning diameter: 200 mm, spindle motor power: 11 W, spindle speed (max.): 5,000 rpm, spindle bore: 50 mm, travel distance Z-axis: 450 mm, type of input current: three-phase, chuck outer diameter: 210 mm, bar diameter (max.): 50 mm, We offer this used DMG Gildemeister CTX 310 eco CNC turning and milling center, year 2008. The lathe is in perfect working condition, and various sets of chucks and driven tools are included in the price. Djdpfx Acsyc Nrgj Njkh All original paper manuals are available. If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: used, Year of construction: 2004, Technical data: Main spindle: Max. turning diameter: 33 mm Max. speed: 8000 1/min Drive power: 5.5 kW Drive power at 60% duty cycle: 7.5 kW Slide 1: Slide travel Z1: 320 mm Slide travel X1: 50 mm Slide travel Y1: 255 mm Rapid traverse speed: 30 m/min Ball screw diameter: 25 mm Tool holder slide 1: Number of tools stationary with tool shank 16 x 16: 5 pieces Slide 2: Slide travel X2: 165 mm Slide path Z2: 200 mm Rapid traverse speed: 30 m/min Ball screw diameter: 30 mm Tool holder slide 2: Number of stations for turret with integrated spindle: 8 pieces Number of axially driven tools (integrated): 8 pieces Coolant tank, approx.: 400 l Coolant pump, max. output: 80 l/min Dimensions (LxWxH), approx.: 2460 x 1510 x 1750 mm Dkedetzyx Tspfx Ac Nsh Equipment: - CNC control Fanuc iT - Workpiece unloading system - IEMCA bar loading magazine - 5-pos. tool carrier plate for slide 1 - Electrical interface and software for bar loading magazine - Collet chuck holder for main and pick-up spindle - 2 Double drill holder for rear machining support with cylinder - Pick-up spindle workpiece pusher

Condition: ready for operation (used), Year of construction: 2006, operating hours: 32,503 h, functionality: fully functional, machine/vehicle number: 01510006441, controller model: MANUAL PLUS 4110, TECHNICAL DETAILS Control: MANUAL PLUS 4110 MACHINE DETAILS Electrical Supply Rated voltage: 400 V Phases: 3~ Frequency: 50 Hz Performance Data Power: 24 kVA Rated current: 35 A Dksdpfx Aox Uz Edsc Neh Fuse rating: 50 A Operating hours: 32,503 h

Condition: used, Year of construction: 2001, chucking diameter 250 mm greates pass round over bed 500 mm swing diameter over slide rest 290 mm centre distance 850 / 1350 mm Dkjdpfxjw Syc Ij Ac Nsh control Heidenhain weight of the machine ca. 2700 t dimensions of the machine ca. 2900 x 1953 x 1825 m

Condition: ready for operation (used), Year of construction: 2010, operating hours: 29,200 h, This Gildemeister Sprint 20-8 was manufactured in 2010. It features a cooling system with a 600l capacity and 50µm filter, alongside a high-pressure pump option of 8 or 20 bar. The machine includes a Bristol B270/E oil mist separator and an IEMCA Boss 332E bar loader for 3m bars. With a chip discharge height of 1,250mm, it's designed for efficient operation. Contact us for more information about this machine. Additional equipment • Mechanical and electrical preparation for fire extinguishing system • Cooling system with 600l capacity and 50µm filter • Pump with options of 8 or 20 bar • IEMCA Boss 332E bar loader for bar length up to 3m • Bristol B270/E oil mist separator • Moving headstock (80mm) with tools on slides plus tool breakage detection Machine Benefits Technical Machine Benefits • Chip discharge height: 1250mm Extra Information Djdpfxox D H I To Ac Njkh Machine still under power

Condition: used, Year of construction: 1999, control Heidenhain centre distance 1400 mm weight of the machine ca. 3,6 t Dkjdpfxew Syd Sj Ac Noh Handwheel defective

Condition: used, Year of construction: 1988, tail stock ja ja condition nicht geprüft Dksdpfx Acsu Su I Ej Neh weight of the machine ca. 3,8 t

Condition: used, Year of construction: 2000, turning diameter . mm turning length . mm control 2x 840 D Kühlmittelsystem chip conveyor ja kW generator - rated current 95,00 A connected load 65,00 kW Dodjqn A Rnspfx Ac Nskh

Condition: good (used), Year of construction: 1998, turning diameter max. 250 mm control Fanuc 16 T 2 toll turrets 2 x 12 tool taper HSK 63 Dkjdpfoqn A Rgsx Ac Njh frequency 50 Hz ampere 168 A Chip conveyor: JAKSS Filter system: JABelade

Condition: good (used), Year of construction: 1984, functionality: fully functional, Swing diameter over bed: 560 mm Swing diameter over cross slide: 250 mm Spindle bore: 65.3 mm Max. power: 15 kW Dkodpsvn Rlzjfx Ac Noh Speeds: 11.2 - 2,240 rpm Distance between centers: 1,000 mm Quill diameter: 80 mm Quill taper: MT 5 Including chip conveyor Including complete documentation Immediately available from stock

Condition: reconditioned (used), Year of construction: 2002, Cycle-controlled lathe GILDEMEISTER NEF 320 With MANUAL PLUS 4110 control Year of manufacture: 2002 Spindle bore: 50.8 mm Distance between centers: 750 mm Swing diameter over bed: 320 mm Swing diameter over cross slide: 150 mm Center height: 160 mm Speed range: 10 – 4000 rpm, stepless With the following accessories: Sliding guard with internal lighting Multifix tool holder with 2 inserts 3-jaw chuck Schunk ROTA – S plus Ø 200 mm 2 sets of soft top jaws ICP contour programming Tailstock with extendable quill Chip tray Dksdpfoxn Apbsx Ac Njh Coolant system Chip rinse gun 6 machine feet Operating manual

Condition: reconditioned (used), Year of construction: 2003, Universal Lathe GILDEMEISTER NEF 320 K Dsdpfx Ajxn Ar Ajc Nskh With Siemens SINUMERIK 810 DE control (SIMATIC PANEL TOUCH SCREEN) Year of manufacture: 2003 Spindle bore: 52 mm Distance between centers: 750 mm Swing diameter over bed: 320 mm Swing diameter over cross slide: 150 mm Cross slide travel: 185 mm Infinitely variable speed range: 14 – 3550 rpm Including the following accessories: Sliding guard with internal lighting Multifix tool holder with 2 inserts 3-jaw chuck SCHUNK ROTA plus Ø 200 mm 2 sets of soft top jaws Coolant system Chip blow gun 6 machine feet Operating manual The machine is in very good condition!

Condition: reconditioned (used), Year of construction: 2006, CNC Lathe GILDEMEISTER CTX 420 linear Equipped with Siemens 840 D powerline control Year of manufacture: 2006 Max. turning diameter: 324 mm Max. turning length: 600 mm Max. swing diameter: 680 mm Spindle bore: 79 mm Max. spindle speed: 4,500 rpm Including the following accessories: Sliding guard with interior lighting 12-position turret with 12 driven stations Y-axis, C-axis Tool measuring device Parts catcher 3-jaw hydraulic chuck 210 mm with foot switch Hainbuch hydraulic collet chuck IRCO Breuning RBK 10012 bar feeder Signal lamp Tailstock with quill Chip conveyor Oil mist extraction Coolant system with high-pressure coolant (IKZ) and belt filter unit Dodpfxjxzt Dcs Ac Nokh Operating manuals

Condition: reconditioned (used), Year of construction: 2005, Cycle-controlled lathe GILDEMEISTER NEF 520 With MANUAL PLUS 4110 control Year of manufacture: 2005 Spindle bore: 70 mm Center distance: 1000 mm Dsdpfx Acjuda Tno Njkh O rotation over bed: 500 mm O rotation over cross slide: 290 mm Center height: 250 mm Speed range: 10 - 3050 rpm infinitely variable With the following accessories: Sliding guard with interior lighting 8-station Sauter VDI 30 turret with driven tools 10 pcs. VDI 30 tool holders 2 pcs. driven tools VDI 30 Coolant device 3 jaw chucks SCHUNK ROTA 0 250 mm ICP contour programming Tailstock with extendable drilling quill Chip tray Operating instructions

Condition: used, Year of construction: 1998, operating hours: 97,593 h, functionality: fully functional, turning diameter: 65 mm, spindle bore: 79 mm, spindle speed (max.): 4,500 rpm, spindle speed (min.): 25 rpm, For Sale: Gildemeister MF Sprint 65 CNC Sliding Headstock Lathe with 3-Meter Bar Feeder, as shown in the pictures. The machine was removed from our workshop in fully functional condition. A video of the machine in operation prior to disassembly is available upon request. Approximately five years ago, the linear guides of the X1 and Z1 slides (on the main spindle side) were replaced, including bearings and belts. A new HMI interface was installed recently. Detailed specifications and technical data can be found in the attached PDF. Dkedewym Nfjpfx Ac Njh TECHNICAL DATA Control: Sinumerik 840C Bar Feeder: SIMAG 65.1-3200G, Year of Manufacture: 1998 Bar Length: 3 meters Bar Diameter / Spindle Bore: 65 mm Main Drive Power Output: 28 / 21 kW Speed Range: 25 – 4,500 rpm Torque: 320 / 240 Nm Maximum Feed Rate for Thread Cutting: 10 m/min C-Axis Speed: 120 rpm C-Axis Torque (Holding Torque): 180 Nm Tool Carrier Number of Tool Stations: 8 Shank Diameter (DIN 69880): 30 mm Number of Driven Tool Stations: 4 Power Output: 7.6 / 4.6 kW Torque: 24 / 14.7 Nm Maximum Speed of Tool Carrier 1: 4,000 rpm Maximum Speed of Tool Carrier 2: 4,000 rpm Slide 1 Cross Travel / Longitudinal Travel: 155 / 280 mm Rapid Traverse Speed X/Z: 22.5 / 22.5 m/min Feed Force X/Z: 900 / 900 daN Slide 2 Cross Travel / Longitudinal Travel: 82 / 120 mm Rapid Traverse Speed X/Z: 22.5 / 22.5 m/min Feed Force X/Z: 900 / 900 daN MACHINE DATA Dimensions with Bar Feeder and Chip Conveyor (L × W × H): approx. 6 × 2 × 2 meters Weight: approx. 6.5 tons Operating Voltage: 50 Hz, 400 V Accessories: Cooling System Chip Conveyor Documentation The offer is subject to change and non-binding, changes and errors in the technical data or the equipment, as well as prior sale reserved Used machines are purchased as seen, without warranty claims. Delivery ex works excluding packaging and insurance, unless otherwise agreed. The price does not include statutory value added tax. As is usual with used machines, payment is made before loading.

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, Gildemeister NEF 320 CNC teach-in lathe Heidenhain Manual Plus Year of manufacture: 2000 Machine hours: 21,594 Max. turning diameter over bed: 320 mm Max. turning diameter over cross slide: 150 mm Max. turning length between centers: 750 mm Max. spindle bore: 50 mm Dkjdpfeycf Rxsx Ac Neh Motor power: 9 kW Spindle speed: 10–4,000 rpm Chuck: Rota-S Plus Multifix quick-change toolholder system Documentation and accessories Machine is powered up for inspection

Condition: used, Year of construction: 1989, Technical details: number of spindles: 6 spindle passage: 20 mm Article: cam-controlled multi-spindle automatic lathe Manufacturer: Gildemeister Type: GS20-6 Yob: 1989 six-spindle automatic lathe 8 main spindles for bars up to D=20mm All cross units are equipped with a tool holder (from Gildemeister or IMG Attachments) All longitudinal units are equipped, either fixed or rotating (without collets) An independent feed is installed at position 1 A gear set for one speed is installed A gear set for one cycle time is installed The scope of delivery regarding the tooling equipment could be different like pictures. Please, contact us for getting more information and pictures on mail(at) or Dsdsx Hggwjpfx Ac Njkh *

Condition: used, Year of construction: 1989, Technical details: number of spindles: 6 spindle passage: 20 mm Article: cam-controlled multi-spindle automatic lathe Manufacturer: Gildemeister Type: GS20-6 Dksdpjx Hgkcofx Ac Neh Yob: 1989 six-spindle automatic lathe 8 main spindles for bars up to D=20mm All cross units are equipped with a tool holder (from Gildemeister or IMG Attachments) All longitudinal units are equipped, either fixed or rotating (without collets) A gear set for one speed is installed A gear set for one cycle time is installed The scope of delivery regarding the tooling equipment could be different like pictures. Please, contact us for getting more information and pictures on mail(at) or *