Used Galion 118 for sale (1,087)

Condition: new, machine/vehicle number: e77e603e96d0ea4194a7f7661, empty load weight: 3,000 kg, maximum load weight: 8,800 kg, overall weight: 11,800 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 5 pairs of lashing eyes bolted to the outside of the floor/outer frame, 3 tons each 2 pairs of lashing eyes additionally bolted to the floor, 5 tons each in the corners Gear support foot at the front Folding rear support 2 wheel chocks with holder Galvanized steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards Towing device central axle trailer Towbar with tested 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 250 mm Axles + suspension GFA or BPW drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires Bjdpfsi Riv Tex Acyelp 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 320 mm high, steel corner stanchions in volume design Drop sides 25 mm hollow aluminum profile, 320 mm high, hinged and removable, subdivided with 1 pair of plug-in middle stanchions Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 3 100 mm long, 510 mm wide, divided lengthwise, can be moved sidewayswith grab handle on the ramps covered with wood With gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Front wall/side wall anodized aluminium Centre stanchion DB 7350 nova grey Hot-dip galvanized drive-on ramps Attention: Archive pictures!

Condition: excellent (used), Year of construction: 2016, Debus DDS 118 / 5/ 23 chip industrial vacuum cleaner 6 bar 4,6 m³/min 278 Manufacturer: Debus Model: DDS 118 full name: DDS 118 / 5/ 23 chips Year of manufacture: 2016 Make No.: 278 operating pressure: 6 bar suction capacity: 4,6 m³/min Air requirement: 1,3 m³/min weight: approx. 30 kg Capacity: approx. 40 liters Dimensions: 55 cm long, 60 cm wide and 150 cm high Bodpeivd A Uefx Acyjlp Condition: used Scope of delivery: see pictures Complete factory lock, large selection of storage platforms, pallet racks, shelf racks, paternosters. High quality industrial machines, lathes, grinding machines, hand machines More items - new and used - you will find in our store! International shipping costs on request!

Condition: excellent (used), saw blade, wood saw blade, circular saw blade, metal circular saw blade, carbide saw blade, segment circular saw blade -Saw blade: Ø 800 x 8 mm Bljdpfx Ajvy Umtjcyop -Inside: Ø: 80 mm -Hole circle: Ø 120 x 22 mm / Ø 160 x 26 mm -Number of teeth: 118 teeth -Weight: 20 kg

Condition: repair required (used), Year of construction: 2008, functionality: not functional, machine/vehicle number: 118009950, spindle speed (max.): 18,000 rpm, feed length X-axis: 2,450 mm, feed length Y-axis: 350 mm, feed length Z-axis: 280 mm, No reserve price – guaranteed sale to the highest bidder! Condition: The machine has always been maintained but now has a software error. TECHNICAL DETAILS X-axis travel: 2,450 mm Y-axis travel: 350 mm Z-axis travel: 280 mm Feed rate: 30 / 15 / 15 m/min Spindle Spindle speed: 18,000 rpm Spindle power: 3 kW Bledjwu Ekqspfx Acyjp Working area Max. machining length: 2,400 mm Compressed air Compressed air connection: 7 bar MACHINE DETAILS Length: 3,100 mm Depth: 1,650 mm Height: 2,250 mm Weight: 1,227 kg Voltage: 400 V, 3~, 50 Hz Connected load: 8 kW

Condition: used, empty load weight: 3,500 kg, maximum load weight: 8,300 kg, overall weight: 11,800 kg, axle configuration: 2 axles, first registration: 10/2009, loading space length: 6,200 mm, loading space width: 2,440 mm, loading space height: 3,000 mm, suspension: air, tire size: 235/75R17,5, color: white, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, tarpaulin and bows, 2-axle, tandem, air-suspended, lifting+lowering, ABS (anti-lock braking system), Edscha, lashing eyes, U-protection, front support, rear support, height-adjustable drawbar Body: Flatbed + tarpaulin Trailer for glass transport with Edscha canopy Tires approx. 50% ACCESSORIES WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! Bsdpfsi Rpx Nsx Acyslp - .

Condition: used, Year of construction: 2015, Overview  This CESPEDES 117-z 118-z brewing system was manufactured in 2015 and has a wort capacity of 20 HL. It consists of a 2-vessel system in German style with mash tun and lauter tun and is heated by a steam generator with a capacity of 300 kg/h. The system is in very good condition and can be demonstrated in operation at any time. Technical details  Brewing plant Manufacturer: CESPEDES Model: 117-z 118-z Year of construction: 2015 Capacity: 20 HL Heating: Steam powered (requires external steam generator) Control: PLC touchscreen (3.5") for controlling mashing and boiling Additional components Hot water tank (HLT): Cylindrical, vertical, insulated Capacity: 2,000 L Material: AISI 304 stainless steel (2 mm thick) Helical pump: Capacity range: 1,000 to 6,000 L/h With frequency converter for adjustable flow rate Plate heat exchanger: Model: UFP-34/65 H Output: 172 kW Steam generator Model: Compat 300 (CE-certified) Fuel: Propane gas or natural gas Thermal output: 195,000 kcal/h Steam production: 300 kg/h Operating pressure: 5 bar Weight: 460 kg (without burner) Total height: 1,670 mm Steam connection: 1” gas connection 3x fermenter Capacity: 2,000 L per fermenter Maximum operating pressure: 3 bar Material: AISI 304 stainless steel (3 mm thick) Design: Cylindrical, vertical with legs Grain mill Capacity: 200 kg/h Bedpfsvxhr Tex Acyolp

Condition: like new (used), functionality: fully functional, machine/vehicle number: WFDFLT21201012268, empty load weight: 3,240 kg, maximum load weight: 8,560 kg, overall weight: 11,800 kg, axle configuration: 2 axles, first registration: 05/2022, loading space length: 5,000 mm, loading space width: 2,420 mm, tire size: 235/75 r17,5, color: green, operation weight: 3,240 kg, Further information Welded steel construction, continuous tilting shaft at the rear with 80 mm ball tilting bearing, gear support foot at the front, folding rear support, wheel chocks with holder, steel underride guard, rear spray flaps across the entire width (not in conjunction with forklift bracket), quarter-shell mudguards, spare wheel, same make as basic tires, steel rim, loose, plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery)Note! Dropside touches storage box when folded down, lockable storage space for access ramps underneath the loading area, pair of aluminum ramps 3,000 mm long, 360 mm wide, load capacity per pair 8,000 kg, (suspension bar for ramps at the rear) Drawbar with tested 40 mm towing eye, height-adjustable drawbar via spindle, max. adjustment range 300 mm BPW drum brake axles, laser-measured axle/chassis Reduction in tire wear and fuel consumption, parabolic suspension with maintenance-free steel/rubber bearings and mechanical axle load compensation (rocker compensation) Bedpfx Aok E Tdajcyelp 2-line compressed air brake systemColor-coded cable routing for easy servicing, hand spindle parking brake Integral air reservoir, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS, Duomatic connection at the front, with connecting cable to the motor vehicle 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable Three-way tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, low-pressure cylinder up to max. 170 bar, without throttle. If required, this can be retrofitted to the truck, hydraulic connection with SVK plug NW 10/3, incl. connecting hose, hydraulic actuation via truck power take-off Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoting with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom, platform length approx. 5,000 mm, side walls with 6 hinges at the bottom. Dropside retraction springs (not possible with split side walls), platform width 2420 mm, pair of lashing eyes in the floor, 5 tons each. Operating instructions: The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Country of registration: Germany, with Dekra approval and expert opinion (according to §13 EG - FGV), 24/7 service hotline, prepared for single-line license plate holder, contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: used, used, good conditionmake Fezertype 016-118-267766vacuum power 20 mbar / 0.37 kWstorage location 97447 Gerolzhofen, free loaded, unpackeddelivery as is, as viewed,without guarantee and warranty Blsdpfsvwfn Njx Acyjp

Condition: used, Gear motor, electric motor, electric gear motor, bevel gear motor -Manufacturer: SEW-Eurodrive, geared motor with brake -Type: RF07 DR63M4/BR -Speed: 118 rpm -Power: 0.18kW -Hollow shaft: Ø 35 x 180 mm Blodpfx Asik Adcecyep -Protection class: IP54 -Brake: 3.2 Nm -Dimensions: 395/118/H165 mm -Weight: 8.4 kg.

Condition: used, functionality: fully functional, Year of construction: 2018, operating hours: 2,177 h, machine/vehicle number: 10067745, empty load weight: 205 kg, construction height: 1,400 mm, fuel type: electric, drive type: Elektro, working height: 2,997 mm, Vertical lift Chassis number: 10067745 Condition: Ready for use and fully functional Technical condition: good Battery Volt: 24V Bodpfxeuhwm He Acyolp Battery Ah: 219Ah Description: Crown WAV 60-118 No.: C Year of construction: 2018 Operating hours: 2,177 The device is visually and technically in good condition. Charger on request Fast and uncomplicated transport possible by arrangement! The advertisement only serves to identify the device! A detailed description of the condition and possible equipment will be provided individually on request! Subject to errors and prior sale, sale only to tradespeople. All used goods are sold without warranty or guarantee. If you have not found the forklift you are looking for, please contact us. We have a large selection of other equipment on site.

Condition: like new (used), functionality: fully functional, machine/vehicle number: WFDFLT21201011556, empty load weight: 3,300 kg, maximum load weight: 8,200 kg, overall weight: 11,500 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 450 mm, suspension: steel, tire size: 235/75 r17,5, color: red, The images are archive images; the vehicle may still be in use! Further information Steel welded construction, continuous tilt shaft at the rear with 80 mm ball bearings Front transmission support leg, folding rear support, 2 wheel chocks with brackets, steel underride guard, full-width rear mud flaps, quarter-shell fenders, spare wheel, same make as base tire, steel rim, loose, 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock. (Lock not included) Note! The side panel touches the storage compartment when folded down. ``` Lockable storage space for loading ramps beneath the loading area, 1 pair of aluminum ramps, 3,000 mm long, 360 mm wide, load capacity per pair: 8,000 kg (rear ramp attachment bar). Towbar with tested 40 mm towing eye, towbar height adjustable via spindle, max. adjustment range: 300 mm. BPW drum brake axles, laser-measured axle/chassis to reduce tire wear and fuel consumption. Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation). Dual-line pneumatic brake system. Color-coded cable routing for easy servicing. Manual spindle parking brake, integral air reservoir, ABS and ALB, with ABS connector at the front, with connecting cable. Caution: The trailer may only be towed by towing vehicles that ensure the ABS is effective. 2 interchangeable coupling heads at the front, with connecting cables to the towing vehicle. 24-volt multi-chamber lights, yellow LED side lighting, 2 white position lights at the front. 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable connectors at the front, with connecting cable. Blodpfslhpzvjx Acyep Three-way tipping system, hydraulic multi-piston press with stroke limiter and safety cable. Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this can be retrofitted to the truck. Hydraulic connection with SVK connector NW 10/3, including connecting hose. Hydraulic operation via the truck's PTO. Sturdy tipping body with 4 mm sheet steel floor, steel side wall construction, continuous side walls, foldable and pivoting with central locking at the bottom. Rear corner stanchions are pluggable. The rear wall is foldable and pivots, with central locking at the bottom. Bedside length approx. 5,000 mm, side walls with 6 hinges at the bottom, bed width 2,420 mm 5 pairs of lashing eyes in the floor, each 5 tons Country of registration: Germany, with DEKRA approval and certificate (according to §13 EG - FGV), 24/7 service hotline, prepared for a single-line license plate holder, contour markings with reflective stripes according to ECE R 048, white on the sides and red on the rear

Year of construction: 2007, condition: used, fuel type: electric, Hydraulic pump, oil pump, hydraulic unit, hydraulic pump, electric motor, DC motor, traction motor, drive motor, hydraulic gear pump -Manufacturer: HPI, hydraulic pump from picking truck type ECE 118 -Hydraulic pump: type 50125677 -Motor: Type AU3480 AMJ5729 24 V 1.5 kW -with: tank and control valve Bledsiz Dtvspfx Acyjp -Number: 4x unit available -Price per piece -Dimensions: 200/180/H370 mm -Weight: 10 kg/pc.

Condition: used, adjustable gear motor, variable speed gear motor, electric motor -Manufacturer variable speed gear Lenze type: 155-ZNA0-80-4 -Manufacturer Motor Dietz type: D48L -Motor power: 0.75 kW -Speed range: 21-118 rpm -Motor: adjustable -height of the shaft axis: 120 mm -Number: 1 motors available -Price: per piece -Drive shaft: Ø 25 mm -Dimensions: 390/400/H250 mm Bodpschbv Hofx Acyelp -Weight: 31 kg

Condition: good (used), grinding drum, deflection drum, belt sander, belt grinder, drum sander, drum sander, conveyor belt rollers, transport rollers, replacement rollers, conveyor belt, roller conveyor, support rollers -Manufacturer: KED Kurt Ehemann, grinding drum drum width 250 mm -Drum: Ø 118 mm -Hole: Ø 30 mm -Number: 2x drum available -Price: per piece -Dimensions: Ø 118 x 310 mm -Weight: 9.7 kg/piece Bodpfx Asvxp Ddocyslp

Condition: good (used), grinding drum, deflection drum, belt sander, belt grinder, drum sander, drum sander, conveyor belt rollers, transport rollers, replacement rollers, conveyor belt, roller conveyor, support rollers -Manufacturer: KED Kurt Ehemann, grinding drum drum width 330 mm Blsdpjvxp Hxofx Acyjp -Drum: Ø 118 mm -Hole: Ø 30 mm -Number: 2x drum available -Price: per piece -Dimensions: Ø 118 x 385 mm -Weight: 11.3 kg/piece

Year of construction: 2007, condition: used, fuel type: electric, Tiller head, pedestrian stacker, pedestrian pallet truck, tiller, steering, electric hand pallet truck -Manufacturer: Jungheinrich, drawbar complete with drive from electric pallet truck ECE 118 Bedpfeiz Dr Aex Acyjlp -Drive motor: 24 VDC / 1.6 kW -Individual components: see photos -Number: 4x drawbar available -Delivery/Price: per piece -Dimensions: 1530/480/H290 mm -Weight: 87 kg/pc.

Condition: used, Gear motor, electric motor -Speed: 118 rpm -Power: 0.15 kW -Construction: B3 angle -Diameter shaft: Ø 20 mm -Protection class: IP 44 Blsdpfjc R R Anjx Acysp -Brake -Number: 1x motors available -Price: per piece -Dimensions: 400/200/H200 mm -Weight: 12.5 kg

Condition: used, Conveyor belt, belt conveyor belt, conveyor belt, belt conveyor, sorting belt, sorting conveyor belt, readout conveyor belt -Side walls made of: stainless steel -Speed: 118 m/min -Drive: 0.75 kW -Belt width: 590 mm -Length: 2000 mm Bljdpfxjffukrs Acyop -Transport dimensions: 4360/1170/H1170 mm -Weight: 684 kg

Condition: used, Position computers, position scanners Blsdob S Hr Depfx Acyop -Voltage: 220 V 50 Hz -Dimensions: 310/340/H210 mm -Weight: 12 kg

Condition: ready for operation (used), Siemens 1FT5062-0AC01-0 - Z permanent magnet motor SN:E0Y61184301007, Z= H40: lubrication, relubrication device DE and NDE, K31: nameplate, 2nd plate is loose in the terminal box, used, normal signs of use, 100% functional, scope of delivery as per photos Bljdpfx Acjuca Rkoyep

Year of construction: 2016, condition: excellent (used), machine/vehicle number: E018769, REF: MM5949 Blodpfx Aexflr Tocyjp 1 x Vemag Process Check Weigher. Technical specification ⚙️ ✅ Manufacturer - VEMAG Maschinenbau GmbH ✅ Model - CHW-2000118. ✅ Type - 4717.275.30. ✅ Serial number - E018769. ✅ Date of manufacture - 2016. ✅ Electric supply - 400 V / 50-60 hz / 3 phase. Note 🗒️ Supplied with manuals.

Condition: used, functionality: fully functional, Year of construction: 2013, load capacity: 300 kg, fuel type: electric, drive type: Elektro, working height: 13,800 mm, Scissor lift Blsdpfjxr Shbjx Acyep Technical condition: good

Condition: used, Technical details: Length: 1530 mm width: 1180 mm height: 110 mm weight of the machine approx.: 500 kg transport dimensions LxWxH: 1,55x1,18x0,1 m steel plate * Blodsu Nkiyopfx Acysp

Condition: used, functionality: fully functional, Year of construction: 2013, operating hours: 834 h, load capacity: 300 kg, fuel type: electric, drive type: Elektro, working height: 13,800 mm, Scissor lift Condition: Ready for use and fully functional Bledpfx Aoxr Sg Rscyep Technical condition: good

Condition: used, functionality: limited functionality, Year of construction: 2012, load capacity: 300 kg, fuel type: electric, drive type: Elektro, working height: 13,800 mm, Scissor lift Bedpfsxr Sg Djx Acyelp Technical condition: poor