Used Est Ticino for sale (2,910)

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Klsdpfx Ahsx Tgr Tjvop Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 1997, turning diameter over bed slide: 1,240 mm, turning diameter over top slide: 980 mm, turning length: 3,000 mm, DBC Turning Length: 3000mm Swing over bed Ø: 1240mm Swing over cross slide Ø:980mm Swing in the gap Ø: 1980mm Gap length: 1500mm Spindle bore: 130mm Spindle power: 30kW Bed width: 500mm Stroke pinole: 300mm Spindle taper: 5Mk Speeds / ranges: 800Rpm Feed rate X-Axis: 8000mm/min. Feed rate Z-Axis: 8000mm/min. Workpiece load: 4000 Length: 7000mm Width: 2200mm Height: 2300mm Weight: 12400kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Ksdpfx Ahox Di Rqsvelp

Condition: excellent (used), Year of construction: 1996, spindle bore: 160 mm, Swing over bed Ø 1040 mm Swing over cross slide Ø 710 mm Swing in the gap Ø 1580 mm DBC Turning Length 3000/4500 mm Gap length 1500 mm Spindle bore 160 mm Spindle power Klodpfextbf Eex Ahvjp 40 kW Bed width 800 mm Spindle taper 6 Mk Workpiece weight 3500 Speeds / ranges 800 Rpm Feed rate X-Axis 10000 mm/min. Feed rate Z-Axis 10000 mm/min. Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1987, turning diameter over cross slide: 810 mm, spindle bore: 130 mm, turning diameter: 1,140 mm, turning length: 7,500 mm, quill stroke: 300 mm, total length: 7,500 mm, total width: 2,300 mm, total height: 1,650 mm, bed width: 600 mm, Please note: not original pictures its only 3000 length not 5000 mm   3 Guide way construction 2 Axis HeidenHain Digital readout Feed in 3 directions all tool post slide Central lubrication   Work load flying in chuck 2500 kg Work load NOT supported 8500 Kg Work load supported 10000 kg   Optional 4 chuck approx. 1200 mm Optional 4 chuck approx. 1500 mm Optional package with 3 steady rest fixed model from  .... to ....  Turning length: 5000 / 7500mm Turning diameter bed Ø: 1140mm Turning diameter slide: 810mm Turning diameter pit Ø: 1500mm Pit length: 2500mm Spindle bore: 130mm Bed width: 600mm Quill: 130Ø Quill stroke: 300mm Ksdpfx Ajv S Dp Iohvslp Spindle mount: 6Mk Power: 25kW Speed: 9 - 900rpm Length: 7500mm Width: 2300mm Height: 1650mm Weight: 12000kg

Condition: excellent (used), Year of construction: 1998, functionality: fully functional, Swing over bed 1,300mm, over cross slide 1.000mm, swing in gap 2,100mm, center distansen 1,500mm, 2,350mm with open bed. Spindle bore 128mm, 450 Rpm, 50 Kw, Chuck 800mm, 4-jaw plate 900mm. Fagor CNC, weight ca 12.000kg Ksdpfx Ahexqp I Nsvjlp

Condition: used, Year of construction: 1976, turning diameter over cross slide: 470 mm, spindle bore: 130 mm, turning length: 1,500 mm, quill stroke: 300 mm, quill diameter: 130 mm, bed width: 600 mm, rotational speed (max.): 600 rpm, quill mount: MK 6, Manufacturer: EST Ticino Model: ET-BM 400 Turning length: 1,500 mm Swing over bed: Ø 800 mm Swing over slide: 470 mm Swing over gap: Ø 400 mm Kledpfjw Ewarox Ahvop Gap length: 750 mm Spindle bore: 130 mm Spindle power: 15 kW Bed width: 600 mm Quill diameter: Ø 130 mm Quill stroke: 300 mm Spindle mount: 6 MK Spindle speed: 600 rpm Dimensions (approximate) Length: 4,500 mm Width: 1,800 mm Height: 1,800 mm Weight: 5,200 kg With accessories: - Safety equipment - Faceplate, four-jaw chuck, clamping jaws, tool holder, centers, drill chuck, tools Please submit inquiries by email only. All information has been provided to the best of our knowledge. Subject to change. This offer is directed exclusively to businesses within the meaning of § 14 BGB. The sale is made with exclusion of any warranty. This exclusion does not apply to claims for damages arising from grossly negligent or intentional breach of duty by the seller or for injury to life, body, or health. For more information, please visit the Witzenmann GmbH website under the sections “Imprint”, “Terms and Conditions”, and “Data Protection”.

Condition: new, Speed relay - new, available sizes: ALNICO 01 (01T) ALNICO 02 (02T) ALNICO 04 (04T ALNICO 11 Kodpfewa Sngsx Ahvelp

Condition: excellent (used), functionality: fully functional, Year of construction: 2012, operating hours: 1,451 h, load capacity: 2,500 kg, lifting height: 5,900 mm, free lift: 1,700 mm, fuel type: electric, mast type: triplex, construction height: 2,800 mm, battery capacity: 620 Ah, battery voltage: 72 V, fork length: 700 mm, overall weight: 6,100 kg, empty load weight: 6,100 kg, total height: 2,800 mm, total length: 1,700 mm, total width: 3,150 mm, maximum load weight: 2,500 kg, fuel: electricity, Equipment: adjustable boom, front guard, lighting, pallet forks, The battery has been reconditioned and has an efficiency of 81%. Only 1451 hours. We sell forklifts after a full service. Prepared for the end user. Klodpjyudr Sofx Ahvsp Ready to use. We can arrange transport within Europe and worldwide.

Year of construction: 2023, condition: refurbished (used), This listing is for a vacuum packaging machine from manufacturer VakuMit, model EST 20 LC. The vacuum in this unit is detected using a proprietary, patented process developed by VakuMit. The vacuum packer is equipped with a powerful 21 m³/h pump. Operation is controlled via the LC control panel. The machine has been fully overhauled in our in-house workshop and is in perfect working condition. The base cabinet features ball-bearing drawers and castor wheels with brakes. You will receive an invoice with VAT shown separately. Our used equipment service for you: - 6 months warranty on electrical components (limited to replacement of defective parts, does not cover removal and installation costs) - High-quality branded equipment at fair prices - Professional refurbishment, inspection & expert cleaning - Tested & fully functional – money-back guarantee if not - Flexible shipping or collection options - Competent advice – before and after purchase - Provision of user manuals, wiring diagrams & spare parts - Safety inspection according to DGUV V3 Kledpjyax Ursfx Ahvjp Technical specifications: Base cabinet (W x D x H): 470 x 620 x 760 mm Chamber size: 410 x 420 x 140 mm Seal bar length: 405 mm Power supply: 230 V / 1.3 kW Packaging output: approx. 1-2 cycles/minute Standard vacuum pump: 21 m³/h Weight: approx. 70 kg Machine number: 1900031023 Year of manufacture: 2023 Condition: used, fully refurbished, fully functional LC control – SemisSens Touch: - With push-button operation - Includes patented vacuum detection - Easy cleaning - User-friendly interface Further details: - Complete stainless steel vacuum chamber and housing - Easily removable seal bar - Automatic adjustment of sealing intensity - Service-friendly machine design - Soft-air return ventilation - Acrylic lid for monitoring the packaging process - Automatic operation cycle with lid opening - Vacuum detection (no timer-based controls) Shipping: Delivery or collection by arrangement Worldwide shipping available on request Shipping to islands or mountain stations only by special arrangement Subject to alterations and errors. If you have any questions, need advice or would like to view the machine on-site, please contact us by phone during our business hours: Monday–Friday 09:00 – 13:00 and 14:00 – 17:00. Sale only subject to our general terms and conditions (AGB).

Condition: used, pressure 160 t passage width / mm stroke / mm Working height 800 mm total power requirement 15 kW Klsdpfx Ahjiulkqovjp weight of the machine ca. 11,8 t - Table size: 1000x1000mm - Distance table/ram, large stroke above, gain. above: 800mm extra information Removable table

Condition: used, Transformer, transformer, converter, three-phase autotransformer, three-phase transformer, three-phase transformer, single-phase transformer -Manufacturer: Müco, single-phase transformer type EST 160 -Power: 160 VA -Voltage: 230V 50/60Hz -Technical data: see photo type plate Kodpfx Aheub D Scjvslp -Dimensions: 100/80/H100 mm -Weight: 2.3 kg

Year of construction: 2008, condition: excellent (used), Electric heating element Shock- and impact-proof plug-in heating system with heating conductors embedded airtight in silicone.No wear, no corrosion, operational safety even in continuous operation and in case of impacts and shocks. Temperature adjustment via integrated controller with insulated control knob. Permanently connected industrial cable, no vulnerable plug connections. High-strength special aluminum profile for high load capacity and flat pressing surfaces on all sides. Gold anodized finish as standard, scratch and abrasion resistant, easy to clean. Size:Type: EST 21 Length: 2100 mm Connected load: 1100 Watt, 230 Volt Temperature: 0 / 40 / 70 / 100 / 170 / 200 degrees Location: ex stock 54634 Bitburg - immediately available - Kledpfx Ajlcd Szohvop

Condition: used, functionality: fully functional, Year of construction: 2017, operating hours: 5,346 h, load capacity: 4,000 kg, lifting height: 4,500 mm, fuel type: electric, mast type: duplex, construction height: 2,950 mm, drive type: Elektro, Four-way side loader Kledpfsvvpuwex Ahvjp Mast type: Duplex Technical condition: good Fork positioner,

Condition: excellent (used), Electrical installation tester from the renowned German manufacturer Gossen Metrawatt The PROFITEST MXTRA model is designed for professional measurement of electrical installations and safety inspections. The device is used by electricians, service technicians, and for routine installation inspections. ⸻ TECHNICAL SPECIFICATIONS Manufacturer: Gossen Metrawatt Model: PROFITEST MXTRA Supply voltage: 230 V Measurement category: CAT III 600V, CAT IV 300V Professional electrical installation tester ⸻ INCLUDED IN THE SET PROFITEST MXTRA tester measurement cable adapter carrying bag The exact set is shown in the photos ⸻ APPLICATIONS electrical installation measurement Klsdpfsywcr Djx Ahvjp safety testing installation inspections electrical service ⸻ CONDITION used visually in good condition

Condition: excellent (used), Electrical safety tester from the renowned German manufacturer Gossen Metrawatt The SECUTEST Pro model is designed for testing electrical devices in accordance with the IEC 62353 standard. The set includes several devices along with measuring leads and carrying bags. TECHNICAL DETAILS Manufacturer: Gossen Metrawatt Model: SECUTEST Pro Standard: IEC 62353 Power supply: 230 V Professional tester for electrical device safety SET INCLUDES Several testers Measuring cables Adapters Carrying bags Exact condition as shown in the photos APPLICATIONS Kljdpfx Ahoywcrwevjp Testing of electrical devices Service and maintenance Safety inspections Medical and industrial use CONDITION Used Visually in good condition Technical condition not fully checked IMPORTANT Sale as a set as shown in the photos No additional accessories except those pictured SHIPPING

Condition: used, turning diameter over bed 330 mm centre distance 650 mm Kjdpjyv N Nyjfx Ahvolp spindle bore 36 mm weight of the machine ca. 600 kg

Condition: excellent (used), functionality: fully functional, Max. air flow rate: 800 m³/h Max. negative pressure: 1,800 Pa Suction connection: 150 mm Suction connection height: 300 mm Drive power: 1.10 kW Connection voltage: 220 / 380 volts (4.33 / 2.5 amps) Klodpfoyv Eu Ssx Ahvjp Dimensions (L/W/H): 610 x 740 x 1,150 mm Total depth: 670 V Sound pressure level: 72 dB(A) Weight: 70 kg • Includes flexible suction arm • Suitable for almost all types of dust • Cleanable, durable bag filter

Condition: good (used), Year of construction: 2007, functionality: fully functional, filter area: 64 m², suction capacity: 4,500 m³/h, negative pressure: 3,200 Pa, Dust extraction, welding fume extraction, cartridge filter self-cleaning, pneumatic, vacuum for plasma, laser , sandblasting, soda blasting, shot blasting and all kinds of dry dust. Brand : ESTA Model : DUSTEX F-64 The filter is cleaned by compressed air pulses during operation, which makes the device highly efficient. Fan on the clean side which reduces the risk of explosion to a minimum. Parameters : Capacity - 4500 m3/h Kodpfxevkd Rpe Ahvolp Vacuum - 3200 Pa Filtration area - 64 m2 Cartridge filter cartridges - 4 pieces. 4 Kw motor. Inlet diameter - 280mm Complete with HEPA filter of filtration class H13 The device from the year 2007

Condition: used, Year of construction: 1980, total length: 1,960 mm, total width: 1,050 mm, total height: 1,570 mm, Empty weight: 1.500 kg - Year: 1980 - Documentation available: No - CE certificate present: No - Serial number: 1123 - Drive system: Conventional - Power [kW]: 5.5 - Centre height [mm]: 180 - Swing over bed [mm]: 360 - Distance between centres [mm]: 800 - Bed width [mm]: 330 - Spindle bore [mm]: 52 - Min. spindle speed [rpm]: 44 - Max. spindle speed [rpm]: 2000 - Options: Quick-change tool post, Four-jaw chuck - Transport dimensions: 1960mm x 1050mm x 1570mm (l x w x h) - Transport weight [kg]: 1500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum Kedpfxjyvtkhe Ahvslp

Condition: used, Year of construction: 2003, Manufacturer: Pester Pac Automation Model: Pewo-fold 1 Year: 2003 Type: Cellophane wrapping machine Film type: OPP Film width: 90–300 mm Film thickness: 0.020–0.050 mm Max. roll diameter: 350 mm. Max. capacity: 50 strokes/min Kjdpfex R D Dhjx Ahvslp Format (min): 60 mm x 30 mm x 60 mm Format (max):250 mm x 250 mm x 140 mm Formats: 2x2 = 90 x 100 x 54: capacity: 50 cycles/min 2x3 = 90 x 150 x 54: capacity: 35 cycles/min 2x4 = 90 x 200 x 81: capacity: 18 cycles/min Power supply: 4 x 400 V + N + PE / 50-60 Hz Installed power: 4 kW (6 A) Air pressure: min. 4 bar / max. 10 bar Documentation available

Condition: used, Year of construction: 2003, Manufacturer: Pester pac automation Model: PEWO-pack 450 (with PEWO-therm tunnel) Year: 2003 Type: PE shrink wrapper/band wrapper with shrink tunnel Application: bottles, vials, vertical cartons, etc. Maximum speed: 60 products/min Passage width: 450 mm Configurable batch sizes Product guidance via upper belts and support rails Film type: PE Film width: 50–250 mm Film thickness: 0.025–0.10 mm Max. roll diameter 300 mm. Power supply: 3×400 V + N + PE, 50–60 Hz. Installed power: 10 kW (≈ 19.0 A) Air pressure: ≈ 5–10 bar Kjdpsx R D Adjfx Ahvolp The machine is sold with a dual-position feed conveyor: Feeding system for shrink wrapper Accumulation conveyor feeder for manual packaging Various formats available Complete documentation

Condition: new, Year of construction: 2026, 0330 mm 210 mm 0635 mm 167 mm 40 mm 2,2 kW spindle turning speed - stepless 30-3000 U/min Klodpfx Aheyu U Drovop

Condition: new, Year of construction: 2024, functionality: fully functional, FIVE STAR THM-460 Horizontal dual-head milling machine with indexing axis Ideal machine for milling and chamfering P-plates for toolmaking from 4 sides in one clamping. Basic technical equipment: Control system - FANUC 0i-MF - User-friendly touch screen, 10.4" color display - Dialog-supported data input Machining capacities - Workpiece length min./max.: 20 - 460 mm - Workpiece width min./max.: 20 - 460 mm - Workpiece height min./max.: 12 - 150 mm (opt. 180 mm) - Workpiece corner chamfer Cmax.: 10 mm Travel paths - X-axis (machine table): 620 mm - Y/Z-axis (infeed axis/headstock): 330 mm / 330 mm Drive power of the axes - X-axis motor: 2.5 kW - Y/Z-axis motor: 1.4 kW - B-axis motor: 1.4 kW Speeds - Rapid traverse X (machine table): 15 m/min - Rapid traverse Y (infeed axis): 10 m/min - Rapid traverse Z (headstock): 10 m/min - Manual feed: 0 - 1,500 mm/min - Automatic feed: 0 - 5,000 mm/min Main spindles - Two horizontally opposed milling spindles, designed for heavy-duty cutting - Drive type: Belt drive - Speed range: 100 to 1,000 min-1 each - Drive power: 11 kW each - Spindle interface: 2" / Ø50.8 mm each - Oil-cooled with separate spindle oil cooler (optional) Tools (standard) - Cutter head: Ø160 mm (opt. Ø200 mm) Note: Tools not included in the standard scope of delivery! Rotary axis (B-axis) - Indexing: (standard 5° pitch) - Indexing angle: 0°, 45°, 90°, 135° and 180° (for 2-sided machining) - Table size: Ø320 mm - Max. Max. load: 320 kg Workpiece alignment - 90° stop for easy positioning of the workpieces by the operator - Automatic measuring unit for detecting the workpiece position Guides - X-axis: Linear roller guide - Y-axis: Flat guide, TURCITE-B coated - Z-axis: Flat guide, TURCITE-B coated - 2 chip spirals (left and right) in the machine - Automatic spiral chip conveyor Miscellaneous - Central lubrication oil / air - Switch cabinet with heat exchanger - Machine sheet metal partial cladding - Support work table - Hand tool box - LED work light - 3-color warning light - CE declaration of conformity according to European directives Machine dimensions and weight - Machine size: 2,800 x 3,410 x 2,200 mm - Machine weight: approx. 7,500 kg Spindles - Power-Up spindle motor 15kW - Spindle interface 1-7/8" each, suitable for face cutter head Ø200 mm arbor diameter: Ø47.625 mm tools - Face cutter head Ø200 mm, MAROX-Tools Taiwan Type: SE545R/L0810, DC200 Rotary axis (B-axis) - Indexing axis, 5° increments, standard option Indexing angle: 0°, 45°, 90°, 135° Table size: Ø320 mm Max. Load capacity: 320 kg Compressed air, coolant and chip management - Chip compressed air nozzle, 1 piece each, external to the spindles, standard option (metal compressed air articulated tube) - Coolant system with separate cooling lubricant tank and low-pressure pump, as well as paper filter, tank capacity: 600 liters Kledjvi I Nmjpfx Ahvsp Filter capacity: 80 l/min. - Chip spirals (left and right) in the machine, standard option - Automatic hinged belt chip conveyor

Condition: new, Year of construction: 2024, Model: ER20/10-2000-H1 Payload: 20 kg Kledpfxsxtpkvo Ahvep Reach: 2000 mm Axes: 6 Quantity: 5 robots! Price per unit!

Year of construction: 2011, condition: good (used), Glass plate 6 cameras with illumination Two hoppers + one drive unit Klodpfsyu Ivnsx Ahvep Integrated supply bunker 25 L / 50 kg with control unit Skako Bunker 125 Loader for 10 crates Extra lens TC1224 + holder Extra lens TC23056 + holder without UPS