Used Draw Tube for sale (3,641)

Condition: used, Year of construction: 2007, with light barriers in the inlet area, the dryer only switches on when parts are detected by the light barrier, otherwise the dryer is in energy-savingstandby mode with almost closed mirror halves. Operation via a Siemens panel. - Manufacturer: Venjakob - Type: VEN DRY UV 3D - Year of manufacture: 2007 - Operating side: right - Working width: 1.300mm - Max. Part height: approx. 100mm - Number of tubes: 2 pieces - Suitable for mercury and gallium tubes - 3D for edge drying - Tube power max. 120W/cm - Tube power infinitely adjustable 50-120Watt/cm - With standby mode- With belt conveyor Nsdpfx Aeu S N R Eohvokw - Feed rate: ~ 2.5 - 7.5m/min. - Length: 3,000mm - Bretie: 2.750mm - Total connection ~45KW - Location: in stock - Volt/HZ: 400/50

Condition: excellent (used), Year of construction: 2005, Technical Data: Minimum bending capacity (steel): ø 19.8 x 3.0 mm Maximum bending capacity (steel): ø 76.1 x 3.0 mm Maximum bending capacity (stainless steel): ø 76.1 x 1.65 mm Bending radius: max. 150 mm Bending angle: max. 190° Bending direction: clockwise (right) Maximum tube length: 6000 mm Mobile control panel CE marking Dimensions (L x W x H): approx. 7200 x 2000 x 1650 mm Weight: approx. 3 t Equipment: Torsion device Programmable bending angle Digital travel distance display Digital torsion angle display 1 x movable drawer support Collets Condition: Very good condition, lightly used Nkedpfx Aoynt Icshvew The seller is not liable for any typing or data transmission errors. The machine's appearance, technology, and wear are commensurate with its age; used machines are sold without any warranty.

Condition: used, Year of construction: 1973, pressure 1000 t distance between columns 4150 mm stroke 1200 mm distance table/blankh.,max. stroke up,adjustm. up 2100 mm table surface area 4000 x 2200 mm die-cushion pressure inside the table 360 t stroke of drawing cushion in table 300 mm die-cushion pressure in pusher 100 t Njdpfx Ajynmm Sjhvskw stroke of drawing cushion in pusher 150 mm ram surface 4000 x 2200 mm column travel -side 1300 mm die-cushion inside the table hydraulic, controlled die-cushion in pusher hydraulic, controlled Cut Shock absorption hydraulic Control Siemens S7 height over floor 7,7 m total power requirement 300 kW weight of the machine ca. 280 t dimensions of the machine ca. 5,75 x 4,3 x 9,55 m Year of construction 1973 Modernization 2005 with oil-hydraulic drive, hydraulically controlled drawing cushion in the table and Ram, hydraulic cutting impact damping stored dismantled - short video available from the seller before dismantling

Condition: used, Year of construction: 1972, pressure 800 t distance between columns 3160 mm stroke 1100 mm control Siemens S5 distance table/blankh.,max. stroke up,adjustm. up 1900 mm table surface area 3100 x 1900 mm die-cushion pressure inside the table 300 t stroke of drawing cushion in table 400 mm die-cushion pressure in pusher 80 t stroke of drawing cushion in table 150 mm ram surface 3100 x 1900 mm Njdpfeynmmxox Ahvokw die-cushion in pusher hydraulic, controlled die-cushion inside the table hydraulic, controlled total power requirement 200 kW weight of the machine ca. 150 t dimensions of the machine ca. 4,95 x 3,3 x 10,2 m

Condition: used, Year of construction: 1972, pressure 800 t distance between columns 3160 mm stroke 1100 mm control Siemens S5 distance table/blankh.,max. stroke up,adjustm. up 1900 mm table surface area 3100 x 1900 mm die-cushion pressure inside the table 300 t stroke of drawing cushion in table 400 mm die-cushion pressure in pusher 80 t stroke of drawing cushion in table 150 mm ram surface 3100 x 1900 mm die-cushion in pusher hydraulic, controlled die-cushion inside the table hydraulic, controlled total power requirement 200 kW weight of the machine ca. 150 t dimensions of the machine ca. 4,95 x 3,3 x 10,2 m Nodpfx Aoynmmrshvekw

Condition: used, Year of construction: 1972, pressure 800 t distance between columns 3160 mm Nkodpfeynbdfjx Ahvjw stroke 1100 mm control Siemens S5 distance table/blankh.,max. stroke up,adjustm. up 1900 mm table surface area 3100 x 1900 mm die-cushion pressure inside the table 300 t stroke of drawing cushion in table 400 mm die-cushion pressure in pusher 80 t stroke of drawing cushion in table 150 mm ram surface 3100 x 1900 mm die-cushion in pusher hydraulic, controlled die-cushion inside the table hydraulic, controlled total power requirement 200 kW weight of the machine ca. 150 t dimensions of the machine ca. 4,95 x 3,3 x 10,2 m

Condition: used, Year of construction: 1972, pressure 800 t distance between columns 3160 mm stroke 1100 mm control Siemens S5 distance table/blankh.,max. stroke up,adjustm. up 1900 mm table surface area 3100 x 1900 mm die-cushion pressure inside the table 300 t stroke of drawing cushion in table 400 mm Nodpsynbc Ijfx Ahvskw die-cushion pressure in pusher 80 t stroke of drawing cushion in table 150 mm ram surface 3100 x 1900 mm die-cushion in pusher hydraulic, controlled die-cushion inside the table hydraulic, controlled total power requirement 200 kW weight of the machine ca. 150 t dimensions of the machine ca. 4,95 x 3,3 x 10,2 m

Condition: new, The KPB 81, a robust Tube and Profile Rolling Machine, excels in high-performance bending, combining modern mechanical engineering with powerful hydraulics. This advanced machine allows you to bend medium and heavy steel profiles with remarkable precision, making it ideal for various applications in metal construction, locksmithing, and mechanical engineering. Equipped with three motor-driven rollers, hardened and ground shafts, and an overload slip-clutch, the KPB 81 ensures efficiency and safety. The modular roller system provides optimum adaptability for bending a wide range of profiles, while the hydraulically adjustable bending rollers enhance versatility, allowing for both horizontal and vertical machining. Standard equipment includes a digital display, control panel, and operator manual for intuitive operation. To experience the precision and performance of the KPB 81 in the Tube and Profile Rolling Machines category, you can request a quote today. Nkedpfjn Upglox Ahvjw

Condition: new, functionality: fully functional, power: 3 kW (4.08 HP), Year of construction: 2025, Equipment: air conditioning, cooling unit, G16 Type: Two chucks Nksdpfxowz Ufws Ahvow

Condition: new, functionality: fully functional, Year of construction: 2025, control type: CNC control, laser type: fiber laser, pipe diameter (max.): 9,000 mm, input voltage: 380 V, input frequency: 50 Hz, type of cooling: water, warranty duration: 24 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, model: GS-HG Nksdpewwqvwjfx Ahvew Maximum length of pipe:

Condition: new, functionality: fully functional, Year of construction: 2025, laser type: fiber laser, laser power: 6,000 W, input voltage: 380 V, input frequency: 50 Hz, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, Maximum tube length: Njdsw I In Rspfx Ahvekw

Condition: used, Brush deburring machine, tube deburring machine BAUER type BE 1 Machine. No. Year of construction 2005 Brush diameter 250 mm Brush width 25 - 60 mm Speed 1500 / 3000 rpm Power 2.2 / 3 kW Mains connection 380 Volt, 50 Hz - Material support Nedehrkrwopfx Ahvskw - new deburring brush Space requirement L x W x H 550 x 450 x 440 mm Weight 65 kg good condition

Condition: used, TUBE MILL OTO MILLS 219.10 The OTO MILLS 219.10 is a heavy-duty tube mill, characterized by its rigid mechanical construction and its integration of high-tier industrial components, making it a stable continuous, high-quality industrial production line. Technical specifications · Manufacturer: OTO MILLS · Tube diameter: 88.9 - 219 mm · Square: 90x90 - 200x200 mm. · Rectangular: 20x60 - 250x150 mm. · Thickness: 2.5 - 10 mm. · Speed: Max. 80 m/min · Coil weight: Max. 16 Ton · Tube length: 6 - 12 m Scope of supply · Entry line · OTO 219.10 forming and sizing system · Cutoff and runout system · Electrical and electronic parts · Hydraulic system · Tooling Nksdpfjym Dbdsx Ahvjw · Thermatool HF welder cfi 600 kw · Double seam annealer (500 kw x 2) – Thermatool · Online Eddy current – Foerster · Semi-automatic packaging machine · Tube inside scarfing system – Alpha Metall Tube diameter: 88.9 - 219 mm Square: 90x90 - 200x200 mm. Rectangular: 20x60 - 250x150 mm. Thickness: 2.5 - 10 mm. Coil weight: Max. 16 Ton Tube length: 6 - 12 m Speed: Max. 80 m/min

Condition: used, functionality: fully functional, Year of construction: 2011, operating hours: 500 h, control type: PLC-controlled, degree of automation: automatic, actuation type: hydraulic, pipe length (max.): 3,000 mm, tube wall thickness (max.): 2 mm, bending angle (max.): 180 °, overall weight: 300 kg, power: 1.5 kW (2.04 HP), input voltage: 220 V, input current: 12 A, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, documentation/manual, Metalworking company sell megabender 030 In the equipment have mandrels for tube: 60,3mm x 2mm R120 50mm x 2mm R75 40mm x 2mm R60 32mm x 2mm R100 700 kg - Powerful mandrel bending machine up to 2 "gas pipe (60.3mm) in semi-automatic design (3000 mm pipe slide length) - Electromechanical drive of the bending axis - hydraulic clamping - mandrel feed / extract - 30 programs x 9 bending angle + correction angle Stainless steel 2mm steel 3mm cooper and aluminium up to 4mm Nodpfov Di Dnjx Ahvokw

Condition: as good as new (ex-display), Year of construction: 2024, Tube Bender BB 48 without mandrel - model BB 48 - capacity up to 48 x 3,0 mm (mild steel) round tube mild steel - digital readout - bending angle programable - with foot pedal - bending speed 2,2 rpm - motor 1,5 KW 400 volt 50 hz 3 ph. - all shafts and necessary parts are heat treated and grinded - monoblock body CK 45 - weight ca. 200 kg Njdpfx Aofp Al Uehvekw

Condition: like new (used), Year of construction: 2021, cutting width (max.): 2,500 mm, cutting length (max.): 9,000 mm, Equipment: documentation/manual, PLASMA TUBE AND SHEET METAL COMBINATION WORKING RANGE SHEET METAL MM 2500 X 9000 Nkodpfxsv E Sabe Ahvjw TUBE DIAMETER FROM MM 80 TO MM 550, TUBE LENGTH MM 9000 YEAR OF CONSTRUCTION 2021 HYPERTHERM BRAND PLASMA GENERATOR MODEL XPR 170

Condition: used, The RGM 3, a top-tier Tube End Finishing Machine from KNUTH, is designed for precision and efficiency in tube processing. Its rigid construction and small footprint make it an ideal choice for any workshop looking to optimize space without sacrificing performance. The machine features a jaw chuck at the front and a clamping chuck at the rear, allowing for versatile operations. Additionally, it comes equipped with a tube cutter and an inside deburrer, ensuring clean and accurate finishes on all types of tubing. With the inclusion of a mobile base, the RGM 3 offers easy maneuverability, enhancing its usability. Whether you need to perform intricate tube work or handle larger projects, this highly robust machine is built for the task. Don't miss out on the opportunity to enhance your tube and profile processing capabilities; order online today to bring the RGM 3 to your workshop. Nedjuxc Rhepfx Ahvokw

Condition: good (used), functionality: fully functional, Year of construction: 2002, control type: manual, degree of automation: manual, actuation type: hydraulic, pipe diameter (max.): 6,090,115 mm, tube wall thickness (max.): 3 mm, number of axes: 3, working height: 700 mm, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, operating pressure: 200 bar, pressure (max.): 200 bar, number of digital displays: 3, Equipment: CE marking, documentation/manual, emergency stop, quick-change device, Limpet coil roller hydraulic to form half round pipe from flat stainless steel strip and bending into wanted radius with spiral continuous. -Shafts output 80 mm -Interchangeable set of rollers on the shafts for the different size of pipe 60 mm , 90 mm , 115 mm -Coil holder for the reel metal strip with guide-way bench uncoiling and alignment the steel strip to the rolling machine Njdpfx Aheyik Hcevekw -Pinching lower central roll adjustable to form the half pipe -Digital position readout to determine the bending diameter of the coil, the pitch of the coil, the half tube shape forming -hydraulic arm movable in 3 directions to set the pitch of the coil roll -Upper vertical support hydraulic operated to hold in position the formed diameter and collect the coils from diameter 700 to diameter 3000 mm -Operator console electric with push buttons and digital position readouts for the coil length, the bending radius and the forming load. -Service manuals and operation books along with the machine

Condition: used, Year of construction: 2015, TUBE LASER CUTTING MACHINE, Model LT8, made by ADIGE This tube laser cutting machine is in excellent working condition. Manufactured in 2015, it has been meticulously maintained, ensuring optimal performance. Technical data: - Round profiles diameter: 20 - 220 mm - Square profiles: Max. 200x200 mm - Max length: 8500 mm - Max tube weight: 32 kg/m - Laser Source: CO2 - Laser Power: 3 kW - Lens holders for: 5 & 7.5 “ - Bundle loader & Loading module: with 5 arms - Tube length loading: 8500 mm - Cutting head: 3D Tilt head - Max tube length unloading: 8500 mm - Unloading modules for tube lengths: 4500mm / 6500mm / 8500 mm - Front unloading conveyor for short parts: Up to 500 mm Scope of supply: - TRUMPF TruLaser Tube 5000 - Tube LoadMaster - Bundle loader with 8.5 m step loader - Finished part 8.5 m collecting table - Chiller - Extractor Special features - Machine integration Rofin - Rear scrap conveyor - Capable for open profiles - Handling option for delicate tubes - High speed pierce boost - Weld seam detection - Artube modules second licenses + USB hardware key - CAD – CAM - Artube adv CAM features - Direct import steps / Iges files - Post Processor LT8 for Artube (1st license) - Production time and Cost calculation - Artube Service Contract Annual Fee - Advanced edit - Part viewer - Cut and fold library - Booster drilling process - Remote tele-diagnostic - Siemens 12 months full warranty - Auto focusing head - Protube Express off line nesting and scheduling - Protube Enterprise productivity & machine monitor - Whole nbar processing software - Pierce booster edge detection Nedpfx Aheyma Itsvekw Round profiles diameter: 20 - 220 mm Square profiles: Max. 200x200 mm Max length: 8500 mm Max tube weight: 32 kg/m Laser Source: CO2 Laser Power: 3 kW Lens holders for: 5 & 7.5 “ Bundle loader & Loading module: with 5 arms Tube length loading: 8500 mm Cutting head: 3D Tilt head Max tube length unloading: 8500 mm Unloading modules for tube lengths: 4500mm / 6500mm / 8500 mm Front unloading conveyor for short parts: Up to 500 mm

Year of construction: 2024, condition: refurbished (used), Tube Straightener 6V1+1 90×5, made by CARTACCI Recently revamped Tube diameter size : 12 – 90 mm Wall thickness : 0,8 – 5 mm Tube length : 4 – 12 m Straightening force : 16 Mp Straightening precision : 0,5 mm/m Speed infinitely variable : 0 – 100 m/min Diameter: 12 – 90 mm Thickness: 0,8 – 5 mm Length: 4 – 12 m Straightening force: 16 Mp Nedpfjyma Hvex Ahvskw Straightening precision: 0,5 mm/m Speed: 100 m/min

Condition: used, Multihead cutting machine TRA2000/7/7, made by MAIR Including: 1) Loading table 2) Cutting machine with 7 cutting heads 3) Operator control panel 4) Unloading bin Optional to be build new upon requirement : 5) Double output craddle 6) New electrical control panel with frequency converters for cutting motors 7) Sound and safety protection cover Max. tube length: 7.500 mm Max. loading capacity: 2.000 kg Round tubes (outer ø): 12 – 50 mm Square tubes (hxw): 12×12 – 40×40 mm Rectangular tubes (hxw): 12×16 – 50×30 mm Max. thickness: 2,5 mm Length of tubes to be cut: 330 – 7.400 mm Number of cutting heads: 7 Nkjdpfxeymaypo Ahvow

Condition: used, MULTIHEAD TUBE CUTTING MACHINE MAIR TRA3000/7/7/CAR + RA1 SCOPE OF SUPPLY 1 Loading table with: - Motorised slings loader, to load the complete bundle - Lateral chain transport conveyor, to introduce the tube 1 by 1 - Top support with vertical adjustment (to avoid loading of 2 tubes when working with small diameters) - Length stop and tube loader 2 Cutting machine TRA3000 with: - 7 independent cutting heads - All cutting heads can be lifted independently - Linear guide with scale for positioning of the cutting heads - Centralised tube transport system with production cycle adjustment 3 Single collecting cradle RA1, with: - Independent cradles, to collect the cut tubes - Lateral separators between cradles, to adapt the cradle length to the tube length - Motorised endless slings for soft tube collection. 4 Main electrical cabinet and operator control panel 5 Safety barriers around the machine & photelectric barriers & emergency line. Note: Safety barriers were installed by owner to have the machine under “safety conformity” TECHNICAL SPECIFICATIONS Manufacturer: MAIR Model: TRA 3000/7/7/CAR +RA1 Yearly maintenance: made by MAIR Spain Max. input tube length: 7000 mm Bundle Loader: 3 Tn Max. loading capacity: 3000 Kg Round tubes (outer Ø): 12-60 mm Square tubes (HxW): 12x12-50x50 mm (see note) Rectangular tubes (HxW): 12x16-60x40 mm (see note) Thickness Min-Max.: 0.8 - 4.0 mm (depending on yield) Cutting lengths: 330-6900 mm Max. straightness tolerance: 1 mm/m Number of cutting heads: 7 Nsdpjymax Ejfx Ahvskw Motors power: 2.2 kW Cutting disc diameter: 300 mm Voltage: 380 / 50 V/HZ, 3 phases Compressed air: It must be supplied filtered and lubricated 6 bar Total installed power: Aprox. 21kW – 50Amp Manufacturer: MAIR Model: TRA 3000/7/7/CAR +RA1 Yearly maintenance: made by MAIR Max. input tube length: 7000 mm Bundle Loader: 3 Tn Max. loading capacity: 3000 Kg Round tubes (outer Ø): 12-60 mm Square tubes (HxW): 12x12-50x50 mm (see note) Rectangular tubes (HxW): 12x16-60x40 mm (see note) Thickness Min-Max.: 0.8 - 4.0 mm (depending on yield) Cutting lengths: 330-6900 mm Max. straightness tolerance: 1 mm/m Number of cutting heads: 7 Motors power: 2.2 kW Cutting disc diameter: 300 mm Voltage: 380 / 50 V/HZ, 3 phases Compressed air: It must be supplied filtered and lubricated 6 bar Total installed power: Aprox. 21kW – 50Amp

Condition: used, MULTIHEAD TUBE CUTTING MACHINE MAIR TRA3000/7/8 Scope of supply: 1 Loading table with: - Motorised slings loader, to load the complete bundle - Lateral chain transport conveyor, to introduce the tube 1 by 1 - Top support with vertical adjustment (to avoid loading of 2 tubes when working with small diameters) - Length stop and tube loader 2 Cutting machine TRA3000 with: - 7 independent cutting heads - All cutting heads can be lifted independently - Linear guide with scale for positioning of the cutting heads - Centralised tube transport system with production cycle adjustment 3 Double collecting cradle RA3, with: - Independent cradles, to collect the cut tubes - Lateral separators between cradles, to adapt the cradle length to the tube length Nsdpfxjymaw Uj Ahvskw - Motorised endless slings for soft tube collection. Note: with the double craddle system, it is possible to make the bundling and strapping in collecting craddle nº1, while production continues, without machine stop. 4 Main electrical cabinet and operator control panel NOTE:  This machine has worked very few hours.  Mechanical condition is very good.  It only requires cleaning & repainting to be “as new” Max. input tube length: 8000 mm Bundle Loader: 3 Tn Max. loading capacity: 3000 Kg Round tubes (outer Ø): 12-60 mm Square tubes (HxW): 12x12-40x40 mm Rectangular tubes (HxW): 12x16-50x30 mm Thickness Min.-Max.: 0.8 - 3.0 mm (depending on yield) Cutting lengths: 330 - 7900 mm Max. straightness tolerance: 1 mm/m Number of cutting heads: 8 Motors power: 2.2 kW Cutting disc diameter: 300 mm

Year of construction: 2019, condition: used, Automatic high-precision tube cutting machine TS72, made by ADIGE Cuts round, square, rectangular, and flat-oval tubes up to 102 mm in diameter. Efficient production: - Program up to 4 different cut lengths per tube - Continuous measurement changes for small batches Organized unloading: - Program up to 3 different unloading positions plus a scrap container. Nkodjymangspfx Ahvsw Non-Stop unmanned production: - Automatic production changes without tools. - High-capacity bundle loader holds up to 4000 kg of material. Superior Cutting Quality: High precision, efficiency, and versatility for tube cutting - Independently operated hydraulic material clamps ensure precise clamping and high cut accuracy. - Blade and clamps detach during return movement to prevent wear. TECHINCAL DATA Working range - Round tube cutting: from 8 to 102 mm - Square tube cutting: from 10x10 to 80x80 mm - Bar cutting: Up to 40 mm - Cutting length: From 20 mm to 3.000 mm Loading - Loading from bundle: Fully automatic - Unloading positions: 3 + 1 (scrap) Tools - Cutting blade diameter: From 200 to 350 mm General - Total installed power: 20 kW Round tube cutting: from 8 to 102 mm Square tube cutting: from 10x10 to 80x80 mm Bar cutting: Up to 40 mm Cutting length: From 20 mm to 3.000 mm Loading from bundle: Fully automatic Unloading positions: 3 + 1 (scrap) Cutting blade diameter: From 200 to 350 mm Total installed power: 20 kW

Year of construction: 2023, condition: used, VIOLI Drawing Bench VM/TRI25-3s Manufactured in 2023 The VIOLI Drawing Bench VM/TRI25-3s is a robust and innovative machine designed for precise and efficient metal drawing, featuring a 3-meter useful length and a powerful 2,500 kg pulling capacity. Its patented hydraulic system ensures linear pulling, compact design, and consistent quality. TECHNICAL SPECIFICATIONS Useful Length: 3 Meters Pulling Power: 2,500 kg Drawing force: Max. daN 2500 Operating hydraulic pressure: 180 bar Drawing speed: Min. 0 m/min. - Max. 17 m/min. Drawing reduction: Around 15% of the section Clamping force POINTER: 100 Ton Tolerance: 1 mm Power supply: 400 V - 50 Hz Electric power: 9,2 KW Hydraulic oil: ISO 46 Motor Power: 9.2 kW - 380 V, 50 Hz Noise: At the workplace LP < 70 dB(A) Hydraulic System: Proportional hydraulic pump Carriage Sliding: with ball circulation guides Construction and movable installation of a hale holder to house 1 O hales in line with the trolley; Predisposition for cooling the lubricating oil with the insertion of a stainless steel pipe coil in the tank; Adjustable Die holder; Bar support system; Tank with pump for lubrication; Opening/ closure of pliers operated manually by pneumatic pistan; Compliance: Machine comply with the UE conformity regulations. DETAILED FEATURES Operating System: The system uses a hydraulic piston and patented technology for optimizing space, ensuring linearity with the drawing hole, and minimizing bending of the supporting structure. It allows for a compact die length and double the useful pulling stroke. Caliper Return: A patented double-circuit chain technology returns the caliper to its starting point. This allows the hydraulic piston's length to be half of the useful working stroke. Pulling Power: The pulling power is in line with the drawing die. Speed Control: Manual adjustable speed from 0 to 16 meters per minute (0−16 Mt/m). It offers fine regulation of the speed and constant speed derived from the hydraulics. Tolerance: The tolerance is 1 mm. Nkedeyl U Sqopfx Ahvew Hydraulic System: Features a proportional hydraulic pump. Motor Power: 9.2 kW - 380 V, 50 Hz. Carriage: Carriage sliding with ball circulation guides. Hole Holder: Construction and movable installation of a hole holder to house 10 holes in line with the trolley. Lubrication: Includes a lubrication tank with a lubrication pump. There is also a predisposition for cooling the lubricating oil with a stainless steel pipe coil in the tank. Die Holder: Adjustable. Bar Support: Includes a bar support system. Pliers Operation: Opening and closure of pliers are operated manually by a pneumatic piston. Control Panel: The machine is equipped with a control panel FUNCTION The hydraulic drawing bench VM/TRI253S is a machine used for the cold reduction of the cross section of a metallic rod, both with round or shaped profile, or of an empty or “animated” metallic tube. The reduction of the section is obtained by passing the product through a calibrated drawing die and pulling it, using a mechanical clamp with the force required to obtain the reduction of the section. COMPOSITION OF THE DRAWING BENCH The machine is composed of the following main components: - Metal structure - Carriage equipped with a hydraulically controlled clamp - Carriage drive unit - Hydraulic system - Electrical system Metal structure The metal structure is composed of a recirculating ball guide. At the end of the rails, a suitable sized plate supports t...