Used Double Printing Press for sale (24,230)

Condition: used, Year of construction: 1971, pressure 100 t distance between columns 400 mm stroke 20 - 140 mm table surface area 900 x 710 mm ram surface 560 x 450 mm ram adjustment 80 mm dayligth 470 mm no. of strokes 70 Hub/min total power requirement 10,5 kW weight of the machine ca. 9 t Ppedpfxsxuv Hts Aahsu dimensions of machine L x W x H 1,98 x 1,60 x 3,10 m

Condition: used, Hydraulic Synchronizing Press, Spotting Press AGEO Type GHP 200 H6 4-Column Hydraulic Press, Tool Trial Press, Spotting Press Serial No. 21169 Year of manufacture: 1993 Pressing force: 200 tons Clearance between uprights (front): 1200 mm Upright opening (side): 650 mm Table surface: 1560 x 1010 mm Ram surface: 1560 x 1010 mm Ram stroke: 575 mm Draw cushion stroke: 300 mm Draw cushion holding force: 63 tons Draw cushion ejector force: 30 tons Max. installation height: 775 mm Table height above floor: 1000 mm Guide column Ø: 140 mm Clamping pin bore in ram: 64 mm Pressing speed: 0 to 10 mm/s, stepless Return speed: 0 to 20 mm/s, stepless Main motor power: 22 kW Control pump motor power: 5.5 kW Connection: 400 Volts, 50 Hz - Table and ram with 22 mm T-slots - Two pressure cylinders with electronic precision synchronization control - Stepless electronic stroke limitation (top and bottom with digital travel measurement and position display) - Mechanical safety support device (prevents ram from dropping due to dead weight) - Single-hand and two-hand operation - Electrical tool safety via signal contact - Pressure presetting independent of stroke (via keypad, digital pressure display) - Travel measurement system right and left via rotary encoders - Electrical control: MS-DOS PC with Ageo H v2.23 control software - Operator panel with swiveling display - Stroke movement and press force adjustable via joystick - Adjacent hydraulic power unit with electrical cabinet - Hydraulic draw cushion under the press table - Draw cushion with ejector function - Continuous stroke control - Floor-level installation - Electrical oil temperature monitoring - Operating manual with circuit diagrams Space required by press (upright) L x W x H: 1800 x 1010 x 3470 mm Space required for horizontal transport L x W x H: 3500 x 1800 x 1200 mm Net weight press: 13 tons Space for hydraulic power unit L x W x H: 1000 x 800 x 3040 mm Net weight hydraulic power unit: approx. 1 ton Psdpfx Aajwva I Hohepu The machine was used as a tool trial press in a toolmaking workshop. Very good condition.

Condition: used, Double-column hydraulic press, SMG Type HBP 200 - 2000 / 2000 Manufacturer's No. 7.4117, Year of manufacture 1986 - Refurbished 2000 Clamping force 200 tons Column width at the front 2050 mm Column opening on the side 2030 mm Table surface 2800 x 2000 mm Ram surface 2000 x 2000 mm Ram stroke 700 mm Installation height max. 1850 mm Table height above floor 750 mm Ram retraction force 33 tons Rapid traverse speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety clearance 230 mm Main motor power 75 kW Control pump motor power 11 kW Power supply 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots on the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking in the top dead center position - Linear encoder system with glass scale - Electrical control system renewed in 2000 with SIEMENS PLC S7 - Adjacent control cabinet - 2-hand control panel adjacent - Floor-level installation - Central lubrication - Operating manual with wiring diagrams Space required for the press in upright position L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space required for horizontal transport L x W x H 5900 x 3250 x 2950 mm Psdpfx Aedzp Tcoahopu Weight 38 tons The machine was used as a production press at Volkswagen until 2000. From 2000, the machine was used as a tool try-out press in a toolmaking company. Good condition.

Condition: like new (used), Year of construction: 2005, functionality: fully functional, GEARLESS FLEXOGRAPHIC PRINTING PRESS F&K FLEXPRESS 16S/10 Central impression flexographic printing press Manufacturer: Marga Fischer & Krecke Model: Flexpress 16S/10 Gearless 10 colors Materials that can be printed: PE, PP, OPP, PET, PA. Mechanical speed up to 460 m/min Maximum material width: 1200 mm Maximum printing width: 1150 mm Minimum/maximum print repeat: 370/800 mm Fully automatic turret unwinder and rewinder Unwinder inner diameter: 76 and 152 mm Rewinder inner diameter: 76 mm Maximum coil diameter: 1000 mm Thermal oil drying system Corona treater: 2 units AVT 100% camera system Bloss viscometers Ppodpfx Aaozafipehju Year: 2005

Condition: used, Year of construction: 2007, functionality: fully functional, roll width: 1,000 mm, working width: 1,000 mm, roll diameter: 1,250 mm, The machine consists of 18 printing units (14 I werks and 4 Y werks) and from 2 faltz machines and 5 Meg-Tech roll changers. Can work as two separate machine. The equipment includes: - 4 paint pumps with base containers (complete piping to each work) The upper floor of the machine has an automatic color refill while the code is running the lower floors are topped up by means of a gun. - Quadtech color and rim register - 4 Technotrans for water preparation Ppsdpfx Aaozablajhou The web offset machine is in good condition, connected and can be started for test production. Lately, most often printed 32 pages in color format 31.5 x 42 cm.

Condition: ready for operation (used), Year of construction: 1983, Offset printing machine ULTRAMAN VII AGS/1983 Ppjdpfx Aaoy U Ufdjheu Maximum sheet size 1120x1600 mm Minimum sheet size 600x800 mm Printing on 5 color groups + 1 dispersion varnish group IR drying alcohol dampening and cooling Quick action plate clamps The machine is in good working condition.

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 700 mm, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :600 mm Ram plate:700 x 600 mm table height over floor:850 mm Table size:700 x 600 mm speed of forward flow:10 mm/sec Pjdefxyh Ropfx Aahjpu Pressing speed:10 mm/sec :10 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,2 t dimensions:950 x 2440 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück heating plates :550 x 500 mm :6800 ? :2400 ? :1200 ? :1200 ?

Condition: new, Year of construction: 2019, pressing force: 275 t, pressure:275 t distance between columns:3000 mm total power requirement:30 kW weight of the machine ca.:40 t draw back pressure:27 t pump capacity:Axialpumpe mit Proportionalventil :6000 mm :max. 3000 mm Table dimensions:6000 x 3000 mm table height over floor:700 mm Podpfsfxyigsx Aahopu distance between table / ram:1100 mm :450 l traversing speed:auf X und Y, 30-33 mm/sec. down speed:2-10 mm/sec :2-50 mm/sec. Cylinder hub:900 mm Cylinder diameter:440 mm Stestle extension:200 / 200 mm / Ø :40 mm Siemens Control System:S7 1200 Monitor Siemens 9":Touch Panel Tax desk:tragbar

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 550 mm, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :550 mm Ram plate:700 x 600 mm table height over floor:900 mm Table size:700 x 600 mm speed of forward flow:50 mm/sec Pressing speed:10 mm/sec :50 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,3 t dimensions:1150 x 2600 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück Heating panels (L x B) with 2 measuring sensors diagonally:550 x 500 mm Siemens Control System:S7 1200 Monitor:12 Zoll :2400 ? Podpfx Aasfxygpohopu :1200 ? :1200 ?

Condition: as good as new (ex-display), Year of construction: 2017, machine/vehicle number: DF0052, pressing force: 200 t, pressure:200 t distance between columns:1200x1000 mm stroke:600 mm total power requirement:32,5 kW Pedpfsfxyirsx Aahjpu weight of the machine ca.:20,5 t dimensions of the machine ca.:4000x2600x5000 m draw back pressure:20 t Master cylinder:1 Stück voltage:400 V frequency:50 Hz :24 V :BOSCH/REXROTH dayligth:800 mm :1200x1000 mit T-Nuten nach Kundenwunsch DIN 650-22 mm work height max.:1100 mm pre-running speed:170 mm/sec return speed:150 mm/sec Speed printing phase:15 mm/sek. Hydraulic block:REXROTH demand for oil:500 l pressure control:über PLC (Mindestdruck 20t) Oil Cooling:elektrisch :220 (im Schaltschrank) V memory:200 Programme :über Monitor von 20-200 t Controll:Zweihandbedienung beweglich :2-10 mm/sec :0-10 sec

Condition: as good as new (ex-display), Year of construction: 2022, pressing force: 400 t, Press design double column press Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 4000 kN Free ripping force max. 400 kN Pressure build-up time Closed die steel to steel Max. 4 sec. Dimensions 3,800 mm long and 4,475 mm wide Max. Opening width 800 mm Stroke 800 mm Table height above floor 1100 mm Height above floor (headroom) approx. 4300 mm Hall height min. 5500 mm parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of press without operating materials and table plate approx. 28 t Press table Table size 1500x1500 mm Speeds Fast closing with 100 mm sec. Pressing speed 8 - 3 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Pedpfxjph Uk Ns Aahepu Hydraulics Number of pressing cylinders/driving cylinders 1 pc. Operating pressure max. 300 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 3 bar Main pump BOSCHREXROTH axial piston pump approx. 145 L/min Oil volume approx. HLP 46 MW 1000 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Auxiliary pump BOSCHREXROTH, gear pump 10 L/min Pressure stabilization for up to 300 sec. Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Connection hydraulics main motor 40 kW Sliding table press with 400 T capacity, Closing speed up to 100 mm/ ( adjustable via touch screen ) Opening speed up to 100 mm/sec ( adjustable via touch screen ) Starting press speed 10 mm/sec ( adjustable via touch screen ) table top size 1500x1500mm ram size approx. 1600x1500mm Oil temperature monitoring 55 degree warning, 60 degree shutdown Automatic lubrication ( adjustable via touch screen ) Free positioning of the ram ( adjustable via touch screen ) SICK/PILZ light barriers 14 mm, front, up to 1800 mm height Hydraulic and mechanical ram protection Circuit oil cooling ( adjustable via touch screen ) Ejector in table, 20 T press force, 350mm travel Ejector moves outwards with the table Table plate milled flat, with DIN 22 T grooves Pressure adjustment from 60 T to 400 T ( adjustable via touch screen ) Travel limitation either by pressure or position Set-up mode, single stroke and cycle sequence ( adjustable via touch screen ) Swiveling control panel on the cabinet Two-hand operation, with opening button, manual/single stroke/cycle switchover button Installation, commissioning, instruction against separate charge The control is supplied by SIEMENS. ( S 7 1200 ) Also the touch screen monitor with 9 inch. The remote maintenance unit SECOMEA -Ethernet is included in the delivery. The side of the press has two 1000 mm high and 800 mm wide windows with double doors. (sliding table press, hydraulic press, hydraulic press, double column press)

Condition: as good as new (ex-display), Year of construction: 2023, pressing force: 120 t, table length: 600 mm, table width: 600 mm, Here are the technical data of the offered machine: Technical data + information: Pjdpfx Ajk S Dt Tsahepu HB 2021-A-188, oil hydraulic double column press 120 T bottom piston heating press. - idle speed up to 40 mm/sec - Opening speed up to 40 mm/sec - Starting press speed 5-15 mm/sec - Table size/heating plate size 600 × 600 mm - ram size/heating plate size 600 × 600 mm - 2 heating plates, electrically heated, up to 250 degrees - as OPTION - total size approx. 2000 × 1000 × 2800 mm height - Oil temperature control - Automatic lubrication - Free positioning of the ram - SICK/LEUTZE light barriers 14,1 mm on front side - Circuit oil cooling - Pressure holding valve 0 to 1800 sec. - Rear monitored door - Pressure adjustment from 30 T to 120 T - Travel limitation either by pressure or position - Programming set-up mode, single stroke (adjustable via rotary switch) - Control panel permanently installed in cabinet wall - Two-hand operation - Machine body double painted - Signal light: red: alarm, yellow baking phase, green: ready - Heating plates with electric heating rods, up to max. 250 degrees - Assembly, commissioning, instruction against separate charge Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 1,600 kN Free ripping force max. 200 kN Pressure build-up time closed die steel to steel Max. 8 sec. Dimensions Max. Opening width per compartment 200 mm Stroke and min. opening per compartment 400/200 mm Table height above floor, without heating pl. 850 mm Height above floor (overall height) approx. 2.800 mm Hall height min. 3,500 mm Parallel deviation at 20 °C +/- 0.1 mm Deflection Determined at max. clamping force with 70 % occupancy ≤ 0.2 mm/m Total weight of the press without operating materials approx. 9 to Accessories: 4 HEATING PLATES 500 × 400 mm, max. heating capacity Equipped with temperature sensor 300 degrees Speeds Fast closing with 15 mm sec. Pressing speed 10 mm sec. Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 8 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 240 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH gear pump approx. 48 L/min Oil volume approx. HLP 46 MW 300 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Automatic pressure readjustment after 5 % pressure loss Pressure stabilization for up to 1800 sec. Electrical system Main supply 400 V AC Control voltage Hydraulic pumps 24 V DC 24 V DC Frequency 50 Hz Connection hydraulic main motor 15 kW Total connection approx. without heating plates 19 kW ##### If the press does not exactly meet your requirements, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Our great strength is special machine construction and press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Condition: new, pressing force: 400 t, pressure:400 t distance between columns:3400 mm stroke:500 mm total power requirement:55 kW weight of the machine ca.:49 t draw back pressure:26 t pump capacity:131 Lt./min dimensions:7.900 x 5.500 x 4.300 mm Ppodpfefhcc Rjx Aahju :5000 mm :2800 mm table height over floor:700 mm distance between table / ram:1000 mm :700 l traversing speed:0-33 mm/sec. down speed:0-10 mm/sec :0-25 mm/sec.

Condition: as good as new (ex-display), Year of construction: 2020, pressing force: 20 t, Double column press 20 T capacity, a) Closing speed up to 10 mm/sec b) opening speed up to 30 mm/sec c) table size between columns 1400x1100 mm d) ram size between columns 1400x1100 mm e) Manual lubrication (via grease nipple) f) UKF pump-cooling-filtration ( electrical cooling ) g) Pressure adjustment from 4 T to 20 T ( adjustable via rotary control ) h) Travel adjustable via slide control Type of construction Press design Double column press ,hydraulic Thermally neutral 80 - 120 °C Number of operating sides 1 side Psdpfxohmbhqe Aahspu Forces Pressing force max. 200 kN Free ripping force max. 20 kN Pressure build-up time Closed tool Steel on steel Max. 4 sec. Dimensions Max. Opening width 500 mm Stroke 300 mm Table height above floor, approx. 900 mm Height above floor (headroom) approx. 2800 mm Hall height min. 3,500 mm Parallel deviation at 20°C #ERROR! mm Deflection Determined at max. clamping force with 2/3 occupancy < = 0.4 mm/m Weight Total weight of the press without operating materials approx. 3 to Table cut-out Size 1100x850 mm Speeds Fast closing with 9 mm sec. Pressing speed 9 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Hydraulics Number of press/driving cylinders 2 pcs. Operating pressure max. 280 bar Pressing pressure build-up time 3-5 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH/PARKER approx. 35 L/min Oil volume approx. HLP 46 D 150 litres Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Circulation pump for cooling ACS approx. 6.5 L/min Electrical system Main supply 400 V AC Control voltage 24 V Frequency 50 Hz Hydraulic connection Main motor 3 kW Total connection Approx. 5 kW

Condition: like new (used), Year of construction: 2019, pressing force: 400 t, pressure:400 t Ppsdpfx Aaofh Izmoheu stroke:900 mm Table dimensions:1200 x 1200 mm Deep-Drawing Pillow:150 t travel away deep-drawing pillow:280 mm Daylight Opening:1100 mm

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, color channels: 1, paper weight (min.): 55 g/m², paper weight (max.): 350 g/m², paper width (min.): 205 mm, paper width (max.): 520 mm, paper height (min.): 145 mm, paper height (max.): 360 mm, We offer this Heidelberg GTO offset printing press, ready for immediate use, manufactured in 1991. Ppodpfxoy Ulu Aj Aahju Manufacturer: Heidelberg Model: GTO Year of manufacture: 1991 Condition: ready for use Category: 832 Type: 520 Type description: offset printing press If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, color channels: 2, paper weight (min.): 55 g/m², paper weight (max.): 350 g/m², paper width (min.): 255 mm, paper width (max.): 650 mm, paper height (min.): 190 mm, paper height (max.): 480 mm, counter reading (black): 60,287,241, We offer this ready-to-use Heidelberg MOZ-P offset printing press, manufactured in 1991. Manufacturer: Heidelberg Model: MOZ-P Ppsdpfx Aajy Uln Aohsu Year of manufacture: 1991 If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: used, Year of construction: 2011, Web Width: 850 mm 1. Unwinding and Infeed System - Unwinder with constant web tension control - Web guiding and stabilization unit - Electronically controlled infeed system with precise tension regulation - Complete drive package for accurate web handling 2. Rewinding System - Single-shaft rewinder, max. roll diameter: 1000 mm - Constant tension control for stable winding 3. Surface Treatment & Web Cleaning - Corona treatment unit for surface energy optimization (pre-print) - ACE single-sided contact roller web cleaner for dust and particle removal 4. Printing Units Flexographic Printing Section - 8 flexo printing units with: - Central impression drum - Removable ink drawer (excl. anilox rollers) - Optional flexo features: - Explosion-proof configuration (per print station) - Drum cooling system - Lightweight anilox rollers: - 5 units (195–300 lpi) with gear - 5 units (>300 lpi) with gear - 24 print sleeves with cams - 2 additional ink drawers (tray + rubber roller) - 1 trolley for ink drawers (3 slots: 2 in use + 1 reserve) Special Flexo Units - 1 cold foil trolley - 1 movable cold foil unit (can be positioned at any print station, rail-free design) Rotogravure Printing Section - 1 rotogravure station for front- or reverse-side printing, includes: - Reversing bar for reverse-side printing - Designed for PETROCOLL cold-seal coating (2.8–3.2 g/m² at 180 m/min on paper) - Rotogravure trolley for mobile positioning - Extended hot air drying system: - “Super Hood” with 32 high-efficiency blowers Pedpfx Aey Ey Nisahopu - Methane gas burner for heating - Integrated cooling unit - Electrostatic assist for ink transfer - 3 rotogravure print sizes (16”–26”) - Solvent ink viscometer - Pump and ink supply tank 5. Drying and UV Curing - 8 UV curing units, 22 kW each (one per print station) - Integrated cooling for UV lamps - Drum cooling for heat-sensitive substrates 6. Die-Cutting and Finishing Units - Rotary die-cutter, working width up to 530 mm - Base unit for die station - Trim removal system (up to 530 mm wide) - Matrix waste pressure system (limit: 530 mm) 7. Slitting Section - Shear (scissor) slitting system - 6 Helios box knives with self-sharpening counter blades 8. Electronic Control & Inspection - OMET electronic register control for 8-color operation - Includes “gate” function for accurate registration - Vision system for real-time print inspection - Motorized E+L Elscan camera for high-resolution web monitoring 9. Safety and Compliance - Complete CE-compliant safety guards and emergency stop systems - Designed for ergonomic operation and rapid job changeovers

Condition: used, Year of construction: 1994, pressure 600 t stroke 100 mm no. of strokes 45 /min distance between columns 580 mm dayligth 460 mm table surface area 550 x 620 mm ram surface 550 x 430 mm ram adjustment 50 mm power requirement 15,0 kW Weight 13,5 t dimensions (WxDxH) 1,5 x 2,45 x 2,75 m Nominal force travel 1.7 mm Podew U Ekpopfx Aahjpu Nominal energy 10.2 kJ With knuckle-joint drive, flywheel brake, hydraulic clutch, press frame balancing, self-monitoring control system

Condition: used, Year of construction: 1993, Pressure 1500 t distance between columns 5050 mm stroke 1100 mm Distance table/ram, stroke up 2300 mm Table surface area 5000 x 2700 mm pressure of drawing cushion in table 320 t Die cushion stroke in table 300 mm Die cushion area in table 4300 x 1830 mm Die cushion pressure in ram 120 t Die cushion stroke in ram 200 mm Die cushion area in ram 3410 x 1650 mm Ram surface 5000 x 2400 mm Speed down 360 mm/s Speed up 168 - 505 mm/s Working speed 19 - 86 mm/s Oil volume 10500 l Power capacity 450,0 kW Weight 400,0 t Dimensions (WxDxH) 3,47 x 6,95 x 12,21 m Height above floor 8,21 m Podpfevuucqex Aahepu Height below floor 4,0 m year of manufacture 1983 - overhaul 1993 with oilhydraulic drive, drawing cushion in table, drawing cushion in ram (drawing cushion surface) approx. 3410 x 1650 mm), cutting impact cushioning / stroke limitation (adjustment of the spindle approx. 500 mm, max. dampening force approx. 750 t, dampening stroke max. approx. 30 mm), controllabel dependant on pressure/time and way as is where is, WITHOUT dismantling, WITHOUT loading

Condition: used, Year of construction: 1997, Pressure 500 t distance between columns 1550 mm stroke 600 mm distance table/ram, max. stroke up, adjustment up 900 mm table surface area 1200 x 1300 mm pressure of drawing cushion in table 250 t stroke of drawing cushion in table 150 mm die cushion area 950 x 950 mm table height over floor 1245 mm side window 1250 mm ram surface 1200 x 1300 mm speed down 750 mm/s speed up 780 mm/s working speed 105 mm/s oil volume 4000 l power requirement 263,0 kW weight 45,0 t Dimensions (WxDxH) 3,3 x 3,3 x 6,1 m height over floor 6,1 m Ppodpoy Rutmsfx Aaheu YOM 1978 - overhaul 1997 with oil-hydraulic drive, hydraulic drawing cushion in table, pneumatic ejector in ram (0,5 t), cutting impact cushioning with depth stop (motoric adjustable), mechanical ram interlocking in TDC as is where is, WITHOUT putting into operation

Condition: used, Year of construction: 1988, Pressure 315 t distance between columns 1350 mm stroke 600 mm distance table/ram, max. stroke up, adjustment up 1000 mm table surface area 1200 x 1300 mm table height over floor 1245 mm side window 1250 mm ram surface 1200 x 1300 mm speed down 750 mm/s speed up 680 mm/s working speed 180 mm/s oil volume 2000 l power requirement 150,0 kW weight 35,0 t Dimensions (WxDxH) 3,3 x 3,3 x 5,5 m height over floor 5,5 m with oil-hydraulic drive, controllable dependent on pressure/time and way, hydraulic cutting impact cushioning with depth stop (motorized adjustment), hydraulic ram interlocking as is where is, WITHOUT putting into operation Ppjdpfxoy Rutgs Aahou

Condition: used, Year of construction: 1978, pressure 40 t stroke 8 - 50 mm no. of strokes 50 - 300 /min distance between columns 600 mm dayligth (stroke and adjustment up) 285 mm Ppodpfx Aaoy Rurcshsu column travel -side 280 mm table surface area 590 x 500 mm hole in the table 590 x 40 - 100 mm table height over floor 860 mm ram surface 590 x 380 mm ram adjustment 80 mm material width 200 mm material thickness - 2,5 mm feed length 160 mm power requirement 7,5 kW dimensions of the machine ca. 1,8 x 1,2 x 2,1 mxmxm AS SPARE PARTS DISPENSER

Condition: used, Year of construction: 1988, pressure 160 t distance between columns 880 mm Podoy Ruq Eopfx Aahspu stroke 150 mm distance table/ram, max. stroke up, adjustment up 530 mm table surface area 830 x 1000 mm hole in the table 260 x 360 mm table height over floor - 850 mm side window 610 mm ram surface 830 x 1000 mm power requirement 55,0 kW weight 14,7 t Dimensions (WxDxH) 2,2 x 2,0 x 4,3 m with oil-hydraulic drive, controllable dependent on pressure/time and way, hydraulic drawing cushion in ram (50 t / 10 mm), hydraulic cutting impact cushioning, motoric adjustable depth stop, motoric adjustable table, two-hand operation No foundation pit necessary

Condition: used, pressure 160 t distance between columns 1360 mm stroke 300 mm Distance table/ram, max. stroke up, adjustment up 620 mm table surface area 1300 x 900 mm table height over floor 950 mm side window 640 mm Ppsdpfx Aajyx Im Nehsu ram surface 1300 x 900 mm power requirement 45,0 kW weight 16,0 t Dimensions (WxDxH) 2,5 x 2,1 x 4,1 m with oil-hydraulic drive, controllable dependent on pressure/time and way, cutting impact cushioning, mechanical depth stop No foundation pit necessary